Professional Documents
Culture Documents
Component Maintenance Manual With Illustrated Parts List: Passenger Seats
Component Maintenance Manual With Illustrated Parts List: Passenger Seats
PASSENGER SEATS
Part Number
EC25001G8B03L02 EC25001G8B13R01
EC25001G8B03L30 EC25001G8B13R03
EC25001G8B03R02 EC25001G8B13R04
EC25001G8B03R30 EC25001G8B13R05
EC25001G8B13L01 EC25001G8B13R06
EC25001G8B13L03 EC35001G8B13L50
EC25001G8B13L04 EC35001G8B13R50
EC25001G8B13L05
EC25001G8B13L06
TP1
TP2
This document and all information contained here in is the sole property of ZIM Flugsitz GmbH. No
intellectual property rights are granted by the delivery of this document or the disclosure of its content.
This document shall not be reproduced, altered, reused or disclosed to a third party in any form, paper or
electronic, without the express written consent of ZIM Flugsitz GmbH.
This document is intended for internal use only by ZIM authorized owner, lessee operators and repair
stations and its content shall not be used for any purpose other than that for which it is supplied. This
includes but is not limited to its use in the creation, manufacture, development or derivation of any repairs,
modifications, spare parts, design or configuration changes or to obtain EASA or any other government
or regulatory approval to do so. If consent is given for reproduction in whole or part, this notice shall
appear in any such reproduction in whole.
ZIM assumes no liability whatsoever, whether contractual, warranty, tort or otherwise, for unauthorized
alteration or alterations not performed in accordance with ZIM approved procedures.
TP 3
TRANSMITTAL LETTER
To
The holders of Component Maintenance Manual (CMM) 25-20-72 , Revision No. 2, date Aug 13/18.
General
This Revision Transmittal Letter is attached to the Revision No. 3 of the CMM 25-20-72, date Aug 23/18.
Change Bars
– Small changes in the text are not identified with the change bars
– Nomenclature and item number change of IPL items are only identified in the IPL pageblock
– Consumable / Special Tool name and number changes are only identified in the 9000 pageblock.
Instructions
The pages which have changed with this revision are shown on the List of Effective Pages. The type of the
change is given in the list below.
Make sure that the pages of the CMM are the same as in the List of Effective Pages.
TL
25-20-72 Page 1
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
INTENTIONALLY BLANK
TL
25-20-72 Page 2
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
HIGHLIGHTS
Pages which have been added, revised or deleted are outlined below together with the Highlights of the
Revision.
TITLE PAGE R
HLTS
25-20-72 Page 1
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
INTENTIONALLY BLANK
HLTS
25-20-72 Page 2
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
RECORD OF REVISIONS
INSERTED INSERTED
REV. ISSUE REV. ISSUE
No. DATE DATE BY No. DATE DATE BY
00 Feb 02/18
01 Jun 12/18
02 Aug 13/18
03 Aug 23/18
ROR
25-20-72 Page 1
Feb 02/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
INTENTIONALLY BLANK
ROR
25-20-72 Page 2
Feb 02/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
INSERTED REMOVED
TEMP REV. ISSUE DATE
No. DATE DATE BY DATE BY INCORPORATED
RTR
25-20-72 Page 1
Feb 02/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
INTENTIONALLY BLANK
RTR
25-20-72 Page 2
Feb 02/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
SBL
25-20-72 Page 1
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
INTENTIONALLY BLANK
SBL
25-20-72 Page 2
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LEP
25-20-72 Page 1
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LEP
25-20-72 Page 2
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
ASSEMBLY REMOVAL
LEP
25-20-72 Page 3
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LEP
25-20-72 Page 4
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LEP
25-20-72 Page 5
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LEP
25-20-72 Page 6
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
TABLE OF CONTENTS
PAGE
TOC
25-20-72 Page 1
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
TOC
25-20-72 Page 2
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
TOC
25-20-72 Page 3
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
INTENTIONALLY BLANK
TOC
25-20-72 Page 4
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LIST OF ILLUSTRATIONS
LOI
25-20-72 Page 1
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LOI
25-20-72 Page 2
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LOI
25-20-72 Page 3
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
INTENTIONALLY BLANK
LOI
25-20-72 Page 4
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LIST OF TABLES
LOT
25-20-72 Page 1
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
INTENTIONALLY BLANK
LOT
25-20-72 Page 2
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
INTRODUCTION
This Component Maintenance Manual (CMM) agrees with the requirements that are given in Air Transport
Association (ATA) specification iSpec 2200. It is written in Simplified English created by the AeroSpace and
Defence Industries Association of Europe (ASD). With the data in this CMM a mechanic who does not know
the product can put it back to serviceable condition. The CMM includes routine servicing and maintenance
that is necessary to maintain the passenger seats in a satisfactory operating condition during its life cycle.
2. Manufacturing
A. Make sure the manual contains the data applicable to your component. Look at the title page
for the part number.
B. If it is necessary to identify a part or to find a part number, refer to the Introduction in the
ILLUSTRATED PARTS LIST (IPL) .
C. You must use the instructions in this manual for all the component maintenance. Read all the
applicable WARNINGS and CAUTIONS before you do the work on the component.
A. This CMM will be revised when necessary and will show new data or will include modifications.
All changes to the text are identified by a revision marker in the left-hand margin, opposite the
change(s) only.
B. There are separate service bulletins. Their effect on this manual will show in reissues of the applicable
list of service bulletins.
A. Read and obey all WARNINGS, CAUTIONS and NOTES in this CMM.
WARNING
(a) A warning tells you that injury or death is possible if the instructions are not obeyed.
– Warnings must always be put before the work step to which they apply.
– They must give data about the risk where it is not easily seen.
– Warnings are printed in bold capital letters.
INTRO
25-20-72 Page 1
Feb 02/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
CAUTION
– Cautions must always be put before the work step to which they apply.
– They must give data about the risk where it is not easily seen.
– Cautions are printed in capital letters.
NOTE
INTRO
25-20-72 Page 2
Feb 02/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
B. All values in this manual are in S.I. units or subdivisions of these units. Imperial units are given
in parentheses immediately after the S.I. units.
7. Abbreviations
LIST OF ABBREVIATIONS
Table INTRO-2
INTRO
25-20-72 Page 3
Feb 02/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LIST OF ABBREVIATIONS
Table INTRO-2 (continued)
INTRO
25-20-72 Page 4
Feb 02/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LIST OF ABBREVIATIONS
Table INTRO-2 (continued)
INTRO
25-20-72 Page 5
Feb 02/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
INTENTIONALLY BLANK
INTRO
25-20-72 Page 6
Feb 02/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
TASK 25-20-72-870-001-A01
1. Description and Operation
A. General
This page block gives a description of the passenger seat and data on operation and use.
Nomenclatures used for parts in the description and illustrations agree with nomenclatures in
ILLUSTRATED PARTS LIST (IPL) .
The description enables repair personnel to become familiar with the components and gives
identification data of the major sub-assemblies, modules and parts for removal purposes. You can
also use data in this page block to do training in the use of the seat components in their normal
operational setting.
TASK 25-20-72-870-002-A01
2. Layout
A. For detailed information about seat dimensions, refer to envelope drawings Fig. 9.
25-20-72 Page 1
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
TASK 25-20-72-870-003-A01
3. Description
The seats described in this CMM are made in versions. All the seats are facing in flight direction.
Fig. 1 show the main assemblies of the seats.
The seats are made on modular basis to make the maintenance and repair procedures easier. All of the
modules can be easily removed from the seat with a minimum of tools.
A. Backrest
A table and upper literature pocket are installed on the rear side of the backrest.
B. Armrest
The fixed and FR armrests are not movable. The center moveable armrests can be flipped up.
The FR armrests have a table for each passenger.
C. Backrest Table
The backrest table is installed at the rear side of the backrest. The passenger in the row behind can
use the backrest table in front of him. The cup holder recess is integrated in each table.
D. Armrest Table
E. Literature Pocket
The upper literature pocket is integrated in the backrest module, above the backrest table. The
passenger in the row behind can use the literature pocket to stow e.g. the magazines.
F. Lifevest Box
The lifevest box is installed to the front and rear beam of the seat structure. There is a red pull-strap
below the seat cushion. The pull-strap is attached to the lifevest box.
G. Baggage Bar
The baggage bar is installed to the seat structure to make sure that the baggage does not move out
unintentionally during flight.
H. Steward Step
25-20-72 Page 2
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
The seat assies are attached to the mounting tracks of the aircraft with a front stud located at the
bottom of the front seatleg and the rear fitting located at the bottom of the rear seatleg.
K. Headrest Cushion
The headrests cushion are attached to the backrest structure (inside backrest dress-cover).
The dress cover is attached to the seat cushion and to the backrest structure.
The seat cushions are attached to the seat with hook tapes and loop tapes. They can be easily
removed from the seat structure.
25-20-72 Page 3
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
Backrest
Armrest fixed
Y-Seat Belt
Seat Cushion
Lifevest
Seatleg
Acou Shroud
Shroud Assy (Satellite)
IAT Armrest
with Table inside
25-20-72 Page 4
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
Backrest
Armrest Moveable
Armrest Fixed
Y-Seat Belt
Seat Cushion
DP029-252072-00000-01-02-00
Acou shroud
Life Vest
Bumper
(Spreader Foils)
Baggage Bar
25-20-72 Page 5
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
Toggle
Literature Pocket
Primary Structure
Acou Shroud
Backrest
Table
DP029-252072-00000-01-03-00
25-20-72 Page 6
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
TASK 25-20-72-870-004-A01
4. Operation
A. Operation
SUBTASK 25-20-72-870-001-A01
(1) Backrest Recline
SUBTASK 25-20-72-870-005-A01
(2) Armrest Table Operation
2 Hold the handle at the outer table plate and turn up the complete table.
4 Move the table plate in horizontal direction forward or rearward to necessary position.
3 Hold the handle at the outer table plate and put the table back to the armrest
SUBTASK 25-20-72-870-0001-A01
(3) Backrest Table Operation
1 Hold the backrest table and turn the toggle which keeps the backrest table in stowed
position.
3 Turn the toggle so that it keeps the backrest table in stowed position.
SUBTASK 25-20-72-870-006-A01
(4) Lifevest Box Retrieval
(Refer to Fig. 2)
25-20-72 Page 7
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
(a) Pull the red pull-strap to get access to the life vest. The lifevest is attached to the red
pull-strap with an elastic strap.
1 PULL STRAP
STRAP
DP029-252072-00000-03-01-00
STRAP
2 PUSH LIFEVEST INTO POUCH
CLOSE POUCH
3
LIFE VEST
Figure 2
SUBTASK 25-20-72-870-007-A01
(5) Seat Bottom Operation
(Refer to Fig. 3)
(a) Remove the seat cushion with the dress cover from the seat bottom.
(b) Carefully lift up the seat cushion with the seat dress cover from the seat bottom.
25-20-72 Page 8
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
(c) Pull out the front seating pipe from the spreader (refer to Removal of the Seat Bottom,
subtask-25-20-72-020-013-a01).
(d) Remove the trampoline with the front and rear seating pipes.
25-20-72 Page 9
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
SEAT CUSHION
WITH SEAT COVER DRESS
TRAMPOLINE
DP029-252072-00000-04-01-00
SEATING PIPE
25-20-72 Page 10
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
SUBTASK 25-20-72-870-008-A01
(6) Armrest Movement
1 Hold and move the armrest up to the position levelled to the backrests.
(b) HC Armrest
1 To unlock the armrest, push and hold the lever located below the armrest. Refer to
Fig. 4 for the location of the lever.
3 To lock the armrest, move it down until the lever locks in the armrest structure.
Push to release
discrete latch
DP029-252072-00000-05-01-00
RELEASE LEVER ON THE HC ARMREST
Figure 4
SUBTASK 25-20-72-870-009-A01
(7) Backrest Breakover (Stretcher)
(Refer to Fig. 5)
NOTE: The seat cushion and dress cover are attached with hook and loop tapes.
25-20-72 Page 11
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
2 Remove the trampoline with the front and rear seating pipe (refer to Removal of
the Seat bottom).
3 If installed, cut the tie wrap from the rear tube and backrest shell.
7 Move forward the backrest structure with increase force until you have the necessary
position.
25-20-72 Page 12
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
DP029-252072-00000-02-01-00
STRUCTURE STRETCHER
Figure 5
25-20-72 Page 13
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
NOTE: The seat cushion and dress cover are attached with hook and loop tapes.
2 Remove the trampoline with front and rear seating pipe (refer to Removal of the
Seat bottom).
4 Move rearward the backrest structure with increase force until you have the necessary
position.
6 If necessary, install the tie wrap to the rear tube and backrest shell.
7 Install the trampoline with the front and rear seating pipe.
NOTE: The seat cushion and dress cover are attached with hook and loop tapes.
25-20-72 Page 14
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
TASK 25-20-72-872-801-A01
5. TSO, Layout and Envelope
A. Layout
25-20-72 Page 15
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
16 1 EC25001G8B03R30 TPL RH LR Stretcher, Narrow / No IFE 465/465/465 506 299 175 531 31.2 519 788 3
15 1 EC25001G8B03L30 TPL LH LR Stretcher, Narrow / No IFE 465/465/465 506 299 -175 531 31.2 519 788 3
14 1 EC25001G8B13R06 TPL RH STD Stretcher, Narrow / 3x USB-Power / 1x In-use-Light Bumper 480/480/480 510 299 216 514 38.1 519 858 3
13 1 EC25001G8B13L06 TPL LH STD Stretcher, Narrow / 3x USB-Power / 1x In-use-Light Bumper 480/480/480 510 299 -216 514 38.1 519 858 3
12 1 EC25001G8B13R05 TPL RH STD Stretcher / 3x USB-Power / 1x In-use-Light Bumper 500/500/500 506 303 240 514 38.5 519 926 3
11 1 EC25001G8B13L05 TPL LH STD Stretcher / 3x USB-Power / 1x In-use-Light Bumper 500/500/500 506 303 -240 514 38.5 519 926 3
Over Wing Exit TYPE III, outboard without armrest /
10 1 EC25001G8B13R04 TPL RH OWE 500/500/500 506 292 222 487 41.1 519 926 3
6x USB-Power / 1x In-use-Light Bumper
Over Wing Exit TYPE III, outboard without armrest /
9 1 EC25001G8B13L04 TPL LH OWE 500/500/500 506 292 -222 487 41.1 519 926 3
6x USB-Power / 1x In-use-Light Bumper
Over Wing Exit TYPE III / CW Toggle, -2° Recline, outboard
8 1 EC25001G8B13R03 TPL RH OWE 500/500/500 506 297 239 514 38.4 519 926 3
without armrest / 3x USB-Power / 1x In-use-Light Bumper
Over Wing Exit TYPE III / CCW Toggle, -2° Recline, outboard
7 1 EC25001G8B13L03 TPL LH OWE 500/500/500 506 297 -239 514 38.4 519 926 3
without armrest / 3x USB-Power / 1x In-use-Light Bumper
6 1 EC25001G8B03R02 TPL RH STD CW Toggle / No IFE 500/500/500 506 315 223 548 35.9 519 926 3
5 1 EC25001G8B03L02 TPL LH STD CCW Toggle / No IFE 500/500/500 506 315 -223 548 35.9 519 926 3
4 24 EC25001G8B13R01 TPL RH STD 3x USB-Power / 1x In-use-Light Bumper 500/500/500 506 303 240 514 38.5 519 926 3
3 24 EC25001G8B13L01 TPL LH STD 3x USB-Power / 1x In-use-Light Bumper 500/500/500 506 303 -240 514 38.5 519 926 3
2 1 EC35001G8B13R50 TPL RH FR IAT / 6x USB-Power / 1x In-use-Light Bumper 500/500/500 506 254 184 477 49.7 518 1852 3
1 1 EC35001G8B13L50 TPL LH FR IAT / 6x USB-Power / 1x In-use-Light Bumper 500/500/500 506 254 -184 477 49.7 518 1852 3
Item QTY Seat Part Nomenclature Information Width Overhang SCG SCGF SCGH Max. (kg) BBI BBO PAX
Integrated
Seat Weight
TABLE TO RIGHT
TABLE TO LEFT
16. Life-vests are restrained in pouch thru use of a flap with velcro closure for ECO SEATS
15. See appropriate trim & finish document: 500102-TFD-011 for ECO
13. No-break-over applies to all seats, except Stretcher with quick release pin (Row 29, 30, 31)
11. Estimated integrated seat weight includes all items except life vest. With a 3% weight tolerance.
Estimated integrated seatweights will be revised into Maximum integrated seat weights after FAI inspection
10. Stations are at front stud with aft track fitting in lock position.
9. All seats except front row seats have handicapped armrest aisle side.
7. SEAT BELT: AMSAFE P/N 2232-1-011-8008 Colour Purple / Y-Lap Belt LH / EXTENSION
AMSAFE P/N 2232-1-021-8008 Colour Purple / Y-Lap Belt RH
General Notes:
LAYOUT
(Sheet 1 of 10)
Figure 6
25-20-72 Page 16
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
CROSS SECTION
ECO 3 - 3 ABREAST FRONT ROW
LINING
21.2"
537,5 NOT TO EXCEED
LINE
17.9"
45 4
SCG F SCG F
DP029-252072-00001-01-01-00
TABLE TO RIGHT
TABLE TO LEFT
SC G
LAYOUT
(Sheet 2 of 10)
Figure 6
25-20-72 Page 17
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
CROSS SECTION
ECO 3 - 3 ABREAST STD SEAT
LINING
21.2"
NOT TO
537,5
EXCEED LINE
17.9"
45 4
SCG F SCG F
DP029-252072-00001-01-02-00
SC G
LAYOUT
(Sheet 3 of 10)
Figure 6
25-20-72 Page 18
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
CROSS SECTION
ECO 3 - 3 ABREAST EMERGENCY EXIT TYP III
ROW 12 / 13
LINING
21.2"
NOT TO EXCEED
537,5
LINE
WITHOUT
WITHOUT
ARMREST
ARMREST
17.9"
45 4
SCG F SCG F
CROSS SECTION
ECO 3 - 3 ABREAST STRETCHER
ROW 29
LINING
21.2"
NOT TO EXCEED
537,5
LINE
OFFSET
SPREADER
DP029-252072-00001-01-03-00
OFFSET 17.9"
SPREADER 45 4
SCG F SCG F
LAYOUT
(Sheet 4 of 10)
Figure 6
25-20-72 Page 19
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
CROSS SECTION
ECO 3 - 3 ABREAST STRETCHER
ROW 30
LINING
NOT TO EXCEED
21.3
LINE
54 2
17,5"
44 6
SCG F SCG F
DP029-252072-00001-01-04-00
SC G
LAYOUT
(Sheet 5 of 10)
Figure 6
25-20-72 Page 20
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
CROSS SECTION
ECO 3 - 3 ABREAST STRETCHER LAST ROW
ROW 31
LINING
17.9
45 4
SCG F SCG F
DP029-252072-00001-01-05-00
LAYOUT
(Sheet 6 of 10)
Figure 6
25-20-72 Page 21
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
R 4 66,
10
2 8
01 EC35001G8B13L50
02 EC35001G8B13R50
4.5
114,5
22.9
581,7
NO TABLE
NO TABLE
MONUMENT
MONUMENT
DP029-252072-00001-01-06-00
LAYOUT
(Sheet 7 of 10)
Figure 6
25-20-72 Page 22
Aug 23/18
07 EC25001G8B13L03 DETAIL - TYP III EMERGENCY EXIT
08 EC25001G8B13R03
ROW 12 / 13
CL CL
09 EC25001G8B13L04 NOT TO EXCEED LINE TYP III EXIT
10 EC25001G8B13R04
4 0.3
102,5 8,4
13.7
13.7 347,8
348,5
2.5
62.6 1.2
30.9
5.7 5 3.3
4.3
144,7 127,9 83,9
109,3
3" 3" 3" 3"
LAYOUT
Figure 6
EC25001G8
3.15 3.15
80 80
16 5
(Sheet 8 of 10)
6.5
EXIT signs OWE EXIT signs OWE
3.94
3.94
10 0
10 0
45 4
24 0
24 0
17.1
17.87
434.6
9.45
17.1
434.6
9.45
COMPONENT MAINTENANCE MANUAL
28 38 37 29
25-20-72
ROW 10 ROW 11 1657 8
ROW 12 ROW 13 ROW 14
1670 7
652.68
657.76
685.99
691.07
17424,1
17553,3
DP029-252072-00001-01-07-00
Page 23
Aug 23/18
UPRIGHT -2°
SIDE VIEW RH PASSAGEWAY = 13. 8 13. 7 = PASSAGEWA Y STRETCHER
351, 5 34 9
4. 5 3. 7 CLEARANC E
NOT TO EXCEED LINE TYP III EXIT
114, 5 92, 8
10
R 4 66,
2 8
22. 9 6 6 =2x33" Pitc h 22 4 =8x28" Pitc h 38 37 20 3 =7x29" Pitc h 28 0 =10x28" Pitc h 29 25.4 5
34 0
863 6
63 0
70 5
1600 2
1790 7
40 6
66 8
90 8
317. 1
118 8
121 7
8054, 3
1242. 5
10312, 4
16967, 2
23063, 2
30175, 2
30911, 8
31558, 2
UPRIGHT -2°
SIDE VIEW LH PASSAGEWAY = 13. 8 13. 7 = PASSAGEWA Y
351, 5 349, 1
4. 9 CLEARANC E
4. 5 NOT TO EXCEED LINE TYP III EXIT 123, 7
114, 5
10
R 4 66,
2 8
22. 9 6 6 =2x33" Pitc h 22 4 =8x28" Pitc h 38 37 17 4 =6x29" Pitc h 30 8 =11x28" Pitc h 29 26.4 5
34 0
863 6
63 0
70 5
1600 2
1790 7
40 6
66 8
87 9
317. 1
118 7
121 6
8054, 3
1242. 5
10312, 4
16967, 2
22326, 6
30149, 8
30886, 4
31558, 2
TOP VIEW
LAYOUT
Figure 6
EC25001G8
40 6
66 8
90 8
63 0
70 5
317. 1
34 0
1242. 5
8054, 3
863 6
10312, 4
1600 2
16967, 2
1790 7
23063, 2
30175, 2
30911, 8
31558, 2
(Sheet 9 of 10)
TYP III EXIT STRETCHER
22. 9 6 6 =2x33" Pitc h 22 4 =8x28" Pitc h 38 37 20 3 =7x29" Pitc h 28 0 =10x28" Pitc h 29 25.4 5
F 2 4 4 4 4 4 4 4 4 4 6 8 10 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 12 14 16
E
COMPONENT MAINTENANCE MANUAL
D
0.1 6
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
17. 9
17. 9
17. 9
17. 9
17. 5
17. 9
C
0.1 6
B
1.3 2
A 1 3 3 3 3 3 3 5 13 15
3 3 3 7 9 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 11
25-20-72
22. 9 6 6 =2x33" Pitc h 22 4 =8x28" Pitc h 38 37 17 4 =6x29" Pitc h 30 8 =11x28" Pitc h 29 26.4 5
2.1 3
STRETCHER
SEATS WITHOUT ARMREST
34 0
863 6
63 0
70 5
1600 2
1790 7
40 6
66 8
87 9
317. 1
118 7
121 6
8054, 3
1242. 5
10312, 4
16967, 2
22326, 6
30149, 8
30886, 4
31558, 2
TABLE TO LEFT
DP029-252072-00001-01-08-00
Page 24
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
FRONT VIEW
STRETCHER RH
955, 1
CROSS SECTION
37. 6
STRETCHER RH
ROW 28 ROW 29 5
ROW 30 4 ROW 31
101, 6
12 7
28 28 29 25. 45 "
711, 2 711, 2 736, 6 646, 4
11 EC25001G8B13L05
12 EC25001G8B13R05
13 EC25001G8B13L06
DP029-252072-00001-01-09-00
14 EC25001G8B13R06
15 EC25001G8B01L30
16 EC25001G8B01R30
LAYOUT
(Sheet 10 of 10)
Figure 6
25-20-72 Page 25
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
B. TSO
25-20-72 Page 26
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
F E D C B A
DP029-252072-00001-02-01-00
TSO
CUSHION AND DRESS COVER (Sheet 1 of 2)
Figure 7
25-20-72 Page 27
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
Seat P/N Position Row / Place Seat Cushion P/N Seat Dress Cover P/N Backrest Dress Cover P/N Headrest Foam P/N
1A 5008734001232 5001734002232R5
EC35001G8B13L50 1B
5008734001212 5001734002212R5
1C
1D 5008734001233 5001734002233R5
EC35001G8B13R50 1E
5008734001212 5001734002212R5
1 F
2-10; 14-28 A
EC25001G8B13L01 2-10; 14-28 B
2-10; 14-28 C
2-10; 14-28 D
EC25001G8B13R01 2-10; 14-28 E
2-10; 14-28 F
11 A
EC25001G8B03L02 11 B
11 C
11 D
EC25001G8B03R02 11 E
11 F
5001735002200R5
12 A
EC25001G8B13L03 12 B
12 C
5008734001202 5001734002202R5
12 D
EC25001G8B13R03 12 E
12 F
5008736001200
13 A
EC25001G8B13L04 13 B
13 C
13 D
EC25001G8B13R04 13 E
13 F
29 A 5008734001264
EC25001G8B13L05 29 B
5008734001202
29 C
29 D
5008734001202
EC25001G8B13R05 29 E
29 F 5008734001265
30 A
EC25001G8B13L06 30 B
30 C
5008734001244 5001734002244R5
30 D
EC25001G8B13R06 30 E
30 F
5001735002201R5
31 A
EC25001G8B03L30 31 B
31 C
5008734001254 5001734002254R5
31 D
EC25001G8B03R30 31 E
31 F
DP029-252072-00001-03-01-00
TSO
CUSHION AND DRESS COVER (Sheet 2 of 2)
Figure 7
25-20-72 Page 28
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
C. Configuration
25-20-72 Page 29
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
2.1
53,2
0.9
22
20,1
0.05
1,3
0.79
0.42
10,7
0.81
20,5
B Y 1.2
17.4 30
441,3
DP029-252072-00001-02-05-00
B
C
17.4
441,3
CONFIGURATION
SEAT BELT AND LEGREST (Sheet 1 of 9)
Figure 8
25-20-72 Page 30
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
247.7
9.75
31.2
7
9
40.
SRP
±9
45 °
B
33 2
13.1
39 6
B
15.6
0.37
0.3.6
6
DP029-252072-00001-02-06-00
CONFIGURATION
SEAT BELT ATTACHMENT (Sheet 2 of 9)
Figure 8
25-20-72 Page 31
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
Detail C
2,04
8,15
BK 0.08
BU 0.32
7
Detail D
20,06
Screw 7/16" 1/4-28 UNF
(P/N 505800043)
BV 0.79
TOP OF TRACK
BZ 0.5
DP029-252072-00001-02-07-00
12,68
REAR FITTING ASSY
BW 1.63
41,3 5058600040000
CB 1 CB 1 BT 0.31
25,4 25,4 7,78
CONFIGURATION
FRONT AND REAR FITTING (Sheet 3 of 9)
Figure 8
25-20-72 Page 32
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
10.6
27 0
17 9
23 3
7.1
9.2
13 1
5.2
0.9 9.2 LIFEVEST
22 23 4
1.3 9.6 LIFEVEST-POUCH
32 24 3
7.24
18 4
5.12
13 0
0.98 DETAIL T
0.98 25
25
3.54"
90
VELCRO
DP029-252072-00001-02-10-00
RED STRAP
LIFEVEST-POUCH WHITE LETTERS
PULL
RUBBER-STRAP STRAP
T
13 0
5.1"
0.98
25
CONFIGURATION
LIFE VEST (Sheet 4 of 9)
Figure 8
25-20-72 Page 33
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
Step 2 :
Push fitting into seat track and move
Fitting cap to the specified locking position (station location)
Step 3:
Turn Fitting screw clockwise, until Plunger snaps
in the seat track
Fitting screw and locks the seat position
Step 4 :
Turn Fitting screw further clockwise
and tighten with 8 Nm < Torque < 10 Nm
Plunger
Step 5 :
Push down fitting cap to secure fitting screw
(see view W)
DP029-252072-00001-02-08-00
CONFIGURATION
REAR FITTING (Sheet 5 of 9)
Figure 8
25-20-72 Page 34
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
30
Fitting screw
CONFIGURATION
REAR FITTING (Sheet 6 of 9)
Figure 8
25-20-72 Page 35
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
DP029-252072-00001-02-02-00
CONFIGURATION
PLACARDS (Sheet 7 of 9)
Figure 8
25-20-72 Page 36
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
4.13"
10 5
1,97"
50
2232-1-011-8008, 2232-1-21-8008
1.97"
50
Printing color: black
Front: Arial size 3mm
0.79"
2232-1-011-8008, 2232-1-21-8008
4.13"
10 5
CONFIGURATION
PLACARDS (Sheet 8 of 9)
Figure 8
25-20-72 Page 37
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
Cushion Placard
Placard size 90 x 60 cm
Placard material: Coatet Polyamid 5
Glue: back melt athesive
Thickness 0,2mm
Thickness 0,2mm
or
CONFIGURATION
PLACARDS (Sheet 9 of 9)
Figure 8
25-20-72 Page 38
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
D. Envelope
25-20-72 Page 39
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LINING
IUL IUL
LINING
NOT TO EXCEED LINE
NOT TO EXCEED
LINE OVERWING EXIT
HC HC
IUL IUL
HC HANDYCAP ARMREST
DP029-252072-00001-05-01-00
TABLE TO RIGHT
TABLE TO LEFT
USB OUT
TIP
RACEWAY
25-20-72 Page 40
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LINING
HC HC
IUL IUL
HC HC
LINING
HC HC
IUL IUL
LINING
HC HC
25-20-72 Page 41
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
LINING
21.2"
NOT TO EXCEED LINE 537,5
AQ 1.5
38,2
17.9
0.3 ,5 45 4
7
AR
49,1
1.9
22,9 20.7 20.4 20.4 20.7
52 7 51 8 51 8 52 7
29.3 21.2 21.2 29.3
74 4 53 8 53 8 74 4
36.5 36.5
92 8 92 8
40.2 40.2
102 1 102 1
LINING
21.2"
NOT TO EXCEED LINE 537,5
NOT TO EXCEED LINE OVERWING EXIT
AQ -0.4"
-9,2
0.5
A R 12 ,8
17.9
45 4
25,7 24 4 25 6 25 6 24 4
2.2
AQ 0.9
21,6
0.7
A R 17 ,5 17.9
45 4
25-20-72 Page 42
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
20
CROSS SECTION AIRBUS A320
4 6 3-3 ABREAST STD 3 5
61.4 61.4
155 9 155 9
AP 19.7 19.7 19.7 19.7 19.7 19.7
0.5 50 0 50 0 50 0 50 0 50 0 50 0
12,2
LINING 21.2
537,5
NOT TO EXCEED LINE
A Q 1.6
39,7
0.4 ,5 17.9
AR 10 45 4
9.6 10.1
AS 1 24 4 25 6 10.1 9.6
55,9
25 6 24 4
2.2
25,7 20.7 20.4
52 7 518,7 20.4 20.7
518,7 52 7
29.3 21.2 29.3
21.2
74 4 53 8
53 8 74 4
36.5
36.5
92 6
926,3
40.2 40.2
102 1 1020,8
LINING 21.2
537,5
NOT TO EXCEED LINE
AQ 1
25,1
1.8 17.9
A R 44,9 45 4
A S 0.3
7,1 9.6 10.1 10.1 9.6
24 4 25 6 25 6 24 4
55,9
2.2
20.7 20.4 20.4 20.7
52 7 518,7 518,7 52 7
29.3 21.2 21.2 29.3
74 4 53 8 53 8 74 4
36.5 36.5
926,3 926,3
40.2 40.2
1020,8 1020,8
LINING
21.3"
NOT TO EXCEED LINE 54 2
A Q 1.7
DP029-252072-00001-05-04-00
43,9
0.1
AR 3,3 17.5"
44 6
AS 1
8.4 10.5 10.5 8.4
25,1
55,9
21 4 26 6 26 6 21 4
2.2
25-20-72 Page 43
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
K 21.9" T 8"
557,4 204,4
N 4.3 J 13.9
108.9 353.4
3
3
76,2
114 3
G 45
702.5
F 27.7
629.6
635.4
A 24.8
B 25
42 0
434.1
E 16.5
C 17.1
Q 0.7
DP029-252072-00001-05-05-00
A N 6.9 17
174,7
R 2.6 P 18
65.7 457.2
25-20-72 Page 44
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
SEAT POS. 3 4 5 6 11 12 13 14
K 21.9" T 8"
557,4 204,4
H 14.4 CRP
36 7
J 13.1 SRP
33 2
A W 2.5
63.3
A O 4.8
3
122.9
3
76,2
1142.6
G 45
CRP
702.4
F 27.7
632.2
B 24.9
SRP
CRP
SRP
41 3
E 16.2
434.7
396
D 15.6
C 17.1
31.65
DP029-252072-00001-05-06-00
Q 0.7
17
R 2.3 P 18
59.6 457.2
25-20-72 Page 45
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
K 21.9"
557,4
H 14.4 CRP
36 7
J 13.1 SRP
33 2
AW 2.5
63.3
A O 4.8
122.9
1142.6
G 45
CRP
632.2
B 24.9
CRP
SRP
SRP
41 3
E 16.2
434.7
39 6
D 15.6
C 17.1
DP029-252072-00001-05-07-00
31.65
Q 0.7
17
R 2.3 P 18
59.6 457.2
25-20-72 Page 46
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
K 21.9" T 8"
557,4 204,4
H 14.4 CRP
36 7
J 13.1 SRP
33 2
3
w/o armrest
3
76,2
1142.6
G 45
CRP
702.4
F 27.7
SRP
CRP
SRP
41 3
E 16.2
434.7
39 6
D 15.6
C 17.1
DP029-252072-00001-05-08-00
Q 0.7
17
R 2.3 P 18
59.6 457.2
25-20-72 Page 47
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
K 21 " T 8,7"
533,5 22 0
H 14.4 CRP
36 7
J 13.1 SRP
33 2
3
w/o armrest
3"
76,2
1147,5
G 45.2
CRP
702.4
F 27.7
SRP
CRP
SRP
41 3
E 16.2
434.7
39 6
D 15.6
C 17.1
DP029-252072-00001-05-09-00
Q 0.7
17
R 2.3 P 18
59.6 457.2
25-20-72 Page 48
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
Detail D
CRP
SRP
LUGGAGE REF
DP029-252072-00001-05-10-00
TOP OF FLOOR
12 6
5
17.6
44 6
25-20-72 Page 49
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
Rear view
STD SB 500 w/o IFE
ROW 11
LUGGAGE REF
TOP OF FLOOR
14.2 18.4 18
36 2 46 7 45 8
Rear view
STD SB 480
ROW 30
LUGGAGE REF
TOP OF FLOOR
9.8 15.1 18
25 0 38 4 45 8
Rear view
LR SB 465
ROW 31
DP029-252072-00001-05-11-00
LUGGAGE REF
TOP OF FLOOR
9.5 18.4 18
25-20-72 Page 50
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
Rear view
STD SB 500
LUGGAGE REF
TOP OF FLOOR
12 15.1 18
30 4 38 4 45 8
Rear view
FR SB 500
LUGGAGE REF
TOP OF FLOOR
12 15.1 14.9
30 4 38 4 37 7
Rear view
STD SB 500 OWE
ROW 13
DP029-252072-00001-05-12-00
LUGGAGE REF
TOP OF FLOOR
12 15.1 14.9
30 4 38 4 37 7
25-20-72 Page 51
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
25-20-72 Page 52
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
15 16
NO TABLE FOR
LR-SEATS
DP029-252072-00001-05-14-00
25-20-72 Page 53
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
7
2.83
72
17 8
Detail A
25-20-72 Page 54
Aug 23/18
COMPONENT MAINTENANCE MANUAL
EC25001G8
TASK 25-20-72-700-001-A01
1. General
This page block contains specific tests and procedures which are required to determine the condition of the
passenger seats. You can do the tests described in this page block on fully assembled passenger seats.
TASK 25-20-72-700-002-A01
2. Seat Assy Test and Fault Isolation
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-700-001-A01
(1) Visual Check
SUBTASK 25-20-72-700-002-A01
(2) Test of the Floor Track Alignment
(a) Test if the seatlegs are correctly aligned with the floor tracks.
(b) Check if the front and rear studs are locked in right position.
SUBTASK 25-20-72-700-003-A01
(3) Fault Isolation of the Floor Track Alignment
E. Close Up
Not applicable
TASK 25-20-72-700-003-A01
3. Armrest Movement Test
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-700-004-A01
(1) Armrest Movement
(a) Examine the alignment of the flip-up armrest in deployed and folded position.
(b) Ensure that the flip-up armrest does not drop down in an uncontrolled way.
E. Close Up
Not applicable
TASK 25-20-72-700-005-A01
4. Table Operational Test and Fault Isolation
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-700-008-A01
(1) Armrest Table Deployment Test
Action Result
Open the armcap, pull the table out of this stowage The table moves from stowed position to released
and move it sidewards to a horizontal position, so position.
that the table assy is released.
Pull the table rearward (against flight direction). The table stops in most retracted position.
Push the table forward (in flight direction). The table stops in most extended position.
Open the armcap, move the table upwards to a The table is stowed.
vertical position and rotate it into its stowage.
SUBTASK 25-20-72-700-009-A01
(2) Backrest Table Deployment Test
Action Result
Turn the toggle so that the backrest table assy is The backrest table assy moves against flight direction
released. from loaded position to released position.
Hold the backrest table and turn the complete assy The table arms and the table stop in their aligned use
down (against flight direction). position.
Pull the table rearward (against flight direction). The table stops in most extended position.
Press the backrest table assy slightly against the The backrest table assy is stowed.
backrest and turn the toggle to lock the backrest
table assy.
SUBTASK 25-20-72-700-010-A01
(3) Armrest Table Fault Isolation
The table assy is not in correct Inclination of the table is improperly Adjust the screws to necessary level.
level. adjusted. Tighten the screws (5-95).
SUBTASK 25-20-72-700-011-A01
(4) Backrest Table Fault Isolation
The backrest table assy is not Inclination of the backrest table Adjust the set screws to necessary
in correct level. assy is improperly adjusted. level. Tighten the set screws (8-170).
No friction during the The table attachment is improperly Tighten the set screws (8-160):
movement of the backrest installed.
table assy
Too much friction during the The table attachment is improperly Tighten the set screws (8-160):
movement of the backrest installed.
table assy .
E. Close Up
Not applicable
INTENTIONALLY BLANK
TASK 25-20-72-750-001-A01
1. Schematic and Wiring Diagrams
A. General
WARNING: BEFORE ANY REPAIR WORK MAKE SURE THAT THE ELECTRICAL PARTS OR
COMPONENTS ARE CORRECTLY SWITCHED OFF AND FREE OF ELECTRICAL
LOAD.
CAUTION: MAKE SURE THAT THE ELECTRICAL PARTS, COMPONENTS AND/OR THEIR
COMPARTMENTS ARE SECURED AND SEALED TO RESIST ENTRY OF
LIQUIDS/MOISTURE AND DUST.
(1) This page block provides all the schematic diagrams, wiring and interconnecting diagrams
of the wiring and modules.
TASK 25-20-72-750-002-A01
2. Schematic Diagrams
A. Cable Routing
Additional requirements:
- All cable plate installed side by side should be tied together
with two tiewraps
- Cables installed on cable plate shall be tied to cable plate
every 10cm or less
- Stow overlength on cable plate as loop or slack
General notes:
- For position 1-499 Refer to IFE Package
- For position 500-900 Refer to Installation Kit
- For diamonds refer to General drawing
- Additional drawings:
5001-I-001 - Integration drawing
5001-L-001-007 - General Drawing,
diamonds description, fixation details
DP029-252072-02000-01-01-00
GENERAL DRAWING
(Sheet 1 of 2)
Figure 2001
650
730
650
Crossing cables Cable fixation on seat spreader
650
691
670
650
Cable fixation on seat spreader and hydrolok Cable fixation on seat spreader [2]
650
650
670
691
650
Cable
650
DP029-252072-02000-01-02-00
630,631,632,633,634
650
GENERAL DRAWING
(Sheet 2 of 2)
Figure 2001
Side view
View 5.1
670
LH shown 5
RH mirrored 6
650
651
Flight Direction 691
730
Isometric view
Shroud EEPMS DISC LH (1x EEPMS)
195
195
771 (EEPMS)
DP029-252072-02000-01-03-00
Flight Direction
SHROUDS
(Sheet 1 of 5)
Figure 2002
View 6.1
LH shown 7
RH mirrored 8
Flight Direction
Isometric view
DP029-252072-02000-01-04-00
Flight Direction
SHROUDS
(Sheet 2 of 5)
Figure 2002
Side view
View 7.1 650
650
651
LH shown 9 670
691
730
RH mirrored 10
Flight Direction
136 (J2)
771( PWR/DATA IN)
135
DISCONNECT BRACKET
136
150
DP029-252072-02000-01-05-00
150 (J25)
771
(FROM WALL MONITOR)
Flight Direction
SHROUDS
(Sheet 3 of 5)
Figure 2002
Side view
View 8.1 650
650 670
LH shown 11 651
691
730
Flight Direction
Isometric view
DISCONNECT BRACKET
152
152 (J25)
771 (FROM WALL MONITOR)
DP029-252072-02000-01-06-00
Flight Direction
SHROUDS
(Sheet 4 of 5)
Figure 2002
LH shown 12
650
651
RH mirrored 13
691
730
650
670
Flight Direction
195
151
151 (J25)
771 (FROM WALL MONITOR)
DISCONNECT BRACKET
DP029-252072-02000-01-07-00
Flight Direction
SHROUDS
(Sheet 5 of 5)
Figure 2002
Right view
View 10.1 14
142,143,145
16 (P7,P14)
16
142,143,145
(J7,J7A,J7B J14,J14A,J14B)
View10.2 15
Left view
650
652
15
DP029-252072-02000-01-08-00
140,141,144
140,141,144
(J7/J7A/J7B)
ACOU Shrouds
Figure 2003
Front view
Leg centerline
26 2
10.3
24
11
1
0.4
77
3
3.9 3.4
10 0 87
Front Stud
EC25001G8B03R30
n/a
EC25001G8B03L30
EC25001G8B13R06 7.2
EC25001G8B13R05 5.2
EC25001G8B13R04 4.1 und 4.2
EC25001G8B13R03 n/a
EC25001G8B03R02 5.2
EC25001G8B13R01 5.2
EC25001G8B13L06 7.1
DP029-252072-02000-02-01-00
24
1
0
DP029-252072-02000-02-02-00
General Info:
TPL Front Row
:Raceway Location
disc. shroud
Applicable
Applicable seats:
:E Box SPB seats: 3L04
3R04 3L50
3R50
disc. shroud
w.cable cover
ACOU_1
Figure 2004
(Sheet 3 of 15)
Applicable Applicable
seats: seats:
3L01
3R05 3L05
3R06 3L06
25-20-72
DP029-252072-02000-02-03-00
Jun 12/18
Page 2012
COMPONENT MAINTENANCE MANUAL
EC25001G8
P3
12.3 J3
31 2
POWER INPUT J1
10 0
3.9
Quick 3.9
fixation P1 10 0
Quick
fixation J2
P2
20 2
14 6 8
10 3
5.7
4
P1
J1
12 7
55
27 2.2
5
36
1.4
Fixed with tie wrap
1.1
R2 R1 3.8
79
62
95
97
3.1
2.4
7.2
3.8
Front view
TPL Front row LH
C
IUL B
2.6
65
1.8
45
C B
2.2
20.4 Front Stud 56 Front Stud
51 8 2.9
73
Top view
TPL front row LH
DP029-252072-02000-02-04-00
P8
J8 J8
P8B
P8A J8
AC OUT(P3)
DC OUT(P3)
P3
G
J3 Fixed with
tie wrap
POWER OUTPUT
J1
Fixed with P1
tie wrap
J2
P2
18 5
7.3
13 0
5.1
85
3.4
Fixed with
tie wrap
3.4
8.1 86 Front Stud
9.1 20 7
23 1
Auxiliary view G
0.9
23
3.9 Front Stud
Front Stud 10 0
J2
20 0
7.9
F
P2
14 6
Quick
5.7
fixation
10 0
3.9
Quick
P1
10 4
J1 fixation
4.1
27
74
1.1
2.9
55
2.2
R1 R2
3.8 3.9
Front Stud 95 10 0
7.5 Raceway
19 0 Outlet/
bottom
E opening area
[inch] 12 9,5 8
[mm] 305 240
20 2
Function Front stud to R2 Front stud to R1
8.5
21 7 Flight Direction
9.4
24 0 10.7
27 2
14.5
36 7
IUL
I
H
2.2 2.5
56 64
H I
2.9 20.4
F 73 51 8
J8 P8A P8
P8B J8
J8
AC OUT
DC OUT
Section view I-I
P3
Fixed
J3
with
tie J1 Fixed with
wrap
J tie wrap
P1
J2
18 5
7.3
P2
12 9
5.1
84
3.3
3.4
86
8.2
20 8
9.2 Auxiliary view J
23 4
DP029-252072-02000-02-07-00
Leg
centerline
26
1
0.9
23
Front
Stud 3.9
10 0
Auxiliary view F
View 4.2
Applicable
seats:
3R50
3R04
Leg centerline
Front
Stud
2.6
65
Section view E-E 2.8 2.6
66
71
3 3.4
77 87
Auxiliary view N
3.9
99
Quick
fixation
Leg centerline
99
3.9
DP029-252072-02000-02-08-00
79
3.1
Front 1.3
Stud 32
2.6
67 2.2
56
P3
J3
N
POWER OUTPUT J1
3.9
Quick 10 0
fixation
P1
Quick
fixation J2
P2
7.9
14 6
5.7
84
10 3
4
84
92
3.6
17
54
66
0.7
2.1
2.6
R2 R1 3.7
10 0
Front Stud
3.9
3.9 8.4 95
Raceway 10 0 21 5
Outlet/ 8.7
bottom
opening area 9 22 0
9.2 22 8
[inch] 12,2 11,7 9.4 23 3
[mm]
Function
309
Front stud to R2
298
Front stud to R1
24 0 10.3
26 1
13.7
34 7
Front view
TPL STD LH
IUL
Leg
centerline
Front Stud
0.9 3.4
20.4 23 87
51 8 D 3.9
2.2
56 99
DP029-252072-02000-02-09-00
Top view
TPL STD LH
P8
J8
AC OUT(P3)
DC OUT(P3) P3
J3
POWER OUTPUT
J1
P1 Quick
fixation
J2
94
3.7
P2
20 0
7.9
14 8
5.8
10 2
4
3.7 R3 R4
95 8.4 3.9
Front Stud 21 5 9 10 0
9.4 22 8 Raceway
Outlet/ [inch] 12,7 11,6
[mm] 322 294
23 8 11.6
bottom
opening area Function Front stud to R4 Front stud to R3
29 4
Front view
TPL STD RH
IUL
Scale 1:3
K
Leg
centerline
Front Stud 20.4
51 8
0.9
3.4 K 23 3.9
87 99
Top view
TPL STD RH
Scale 1:3
DP029-252072-02000-02-10-00
J8
P8
P3
J3
POWER INPUT
J1
Quick
fixation
14 8
J2
5.8
P2
200.6
91.8
102.6
7.9
3.6
4
53.7
2.1
3.8
R1 10 0 95.4 Front Stud
8.4
3.9 9.3 214.6
100 10.3 235.6
13.7 26 1
14.5 347.4
367.4
Raceway
Outlet/
bottom
opening area Front View
TPL STD LH (3L06)
Leg
centerline
Front Stud
20.6'
2.2
522
56
L 0.9
3. 23 3.4
99 87
Top View
TPL STD LH (3L06)
DP029-252072-02000-02-11-00
P8
J8
View 6.2
AC OUT
DC OUT
P3
J3
POWER OUTPUT
J1
Quick
P1 fixation
200.8
J2
147.7
7.9
5.8
93.9
10 4
3.7
4.1
3.8 R2
95.5 8.3 3.9
210.2
Front Stud 9.4 100 Raceway
238.2 11.6 Outlet/
[inch]
[mm]
12,9
327
11,6
294
29 4 bottom
Front stud to R2 Front stud to R1
opening area
Front View
TPL STD LH (3R06)
M
Leg
centerline
Front Stud
3.4 M 0.9
87 3.9 23
99
Top View
TPL STD LH (3R06) DP029-252072-02000-02-12-00
J8
P8
View 8.1
P3
POWER INPUT
J3
Quick
fixation
J1 3.9
Quick 10 0
fixation P1
J2
P2
66
2.6
82
20 1
11 7
7.9
4.6
10 3
82
4
96
3.8
14 6
17
5.7
56
0.7
2.2
10 6
98
3.8
4.2
Quick fixation
26
1
R1 R2 3.8
10 0
95
3.9
Front View
TPL OWE LH (3L03)
IUL
P
Leg
centerline
20.4
51 8 Front Stud
P
2.2 0.9
56 23
3.9 3.4
99 87
DP029-252072-02000-02-13-00
Top View
TPL OWE LH (3R03)
P8
J8
View 9.1
Applicable seats:
3R03
P3
POWER OUTPUT
J3
Quick
J1 fixation
P1
J2
20 0
P2
7.9
4 14 6
5.7
10 3
1 86
96 3.4
26
3.8
R1 R2
Front Stud 3.7 3.9
95 8.4 10 0
9 21 5
9.4 22 8
Raceway
10 23 9 Outlet/
bottom
11.4 25 4 opening area
28 9
14.6
37 0
11.6
29 5
12.7
32 3
DP029-252072-02000-02-14-00
Front View
TPL OWE RH (3R03)
Q
IUL
20.4
51 8
3.4 Q
87 3.9
0.9 99
23 2.5
64
Top View
TPL OWE RH (3R03)
P8
J8
DP029-252072-02000-02-15-00
DISASSEMBLY
TASK 25-20-72-030-001-A01
1. Disassembly
A. General
This page block gives complete step-by-step disassembly procedures for the parts of the passenger
seat that you can remove.
NOTE: We do not recommend complete disassembly of the passenger seat. Disassemble the
passenger seat only to the degree which is necessary to remove damaged or defective component.
NOTE: Tag or mark correctly all removed assemblies and subassemblies to facilitate later
exact reinstallation.
(1) Read all instructions and look at the related illustrations before starting disassembly. Refer to
the exploded view illustrations in the ILLUSTRATED PARTS LIST (IPL) for location, sequence,
quantity and identification of assemblies, sub-assemblies and parts. These illustrations are also
intended as a guideline for the disassembly procedure. IPL item numbers are used in the
detailed procedures.
(2) Refer to INSPECTION/CHECK and TESTING AND FAULT ISOLATION to find the condition of
the passenger seat or the cause of malfunction.
TASK 25-20-72-020-801-A01
2. Removal of the Main Seat Assemblies
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-020-011-A01
(1) Removal of the Seat Belt
(a) Push the seat belt shackle together and remove the seat belt (1-380), (1-390), (1-400),
(1A-380), (1A-390), (1A-400), (1B-380), (1B-390), (1B-400), (1C-380), (1C-390),
(1C-400) from the seat belt shackles.
SUBTASK 25-20-72-020-022-A01
(2) Removal of the Seat Cushion
(a) Position both hands on the front of the seat cushion and lift it to remove the seat cushion
from the hook and loop tape.
(c) Remove the seat cushion (1-190), (1-200), (1-210), (1A-190), (1A-200), (1A-210),
(1B-190), (1B-200), (1B-210), (1C-190), (1C-200), (1C-210) with the seat dress cover
(1-220), (1-230), (1-240), (1A-220), (1A-230), (1A-240), (1B-220), (1B-230), (1B-240),
(1C-220), (1C-230), (1C-240).
(d) Loosen the hook and loop tape and remove the seat dress cover from the seat cushion.
SUBTASK 25-20-72-020-012-A01
(3) Removal of the Backrest Dress Cover and Headrest Cushions
CAUTION: DO NOT REMOVE THE BACKREST DRESS COVER FROM THE UPPER SIDE
THAT BEWARE FOR DAMAGE THE DRESS COVER. THE DRESS COVER IS
ATTACHED BETWEEN SHELL AND SEAT FRAME WITH TAPES.
(a) Position both hands on the left hand and right hand side of the middle part of the backrest
cushion and lift it from the rear to the front.
(b) Carefully lift it from the middle to the bottom from the hook and loop tape.
(c) When the middle and the bottom side is released, lift up carefully from the bottom to
the head side.
(d) Remove the backrest dress cover (1-250), (1-260), (1-270), (1A-250), (1A-260), (1A-270),
(1B-250), (1B-260), (1B-270), (1C-250), (1C-260), (1C-270) from the backrest structure.
(e) Remove the headrest cushion (1-280), (1-290), (1-300), (1A-280), (1A-290), (1A-300),
(1B-280), (1B-290), (1B-300), (1C-280), (1C-290), (1C-300) from the backrest structure.
TASK 25-20-72-020-803-A01
3. Removal and Disassembly of the Fixed Armrest
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-020-0003-A01
(1) Disassembly of the Fixed Armrest
(a) Remove the screw (2-120) and the washer (2-110) from the structure and fasten the
armcap.
(c) Remove the front cap (2-40) with the screw (2-50) from the structure.
(e) Remove the foils (2-60), (2-70) from the structure [refer to Repair of the Foils,
task-25-20-72-6000-300-0801-a01].
TASK 25-20-72-000-821-A01
4. Disassembly of the Armrest Movable
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-000-0002-A01
(1) Disassembly of the Movable Armrest
(a) Remove the screw (2A-120) and the washer (2A-110) from the structure and fasten the
armcap.
(c) Remove the front cap (2A-40) with the screw (2A-50) from the structure.
(e) Remove the foils (2A-60); (2A-70) from the structure [refer to Repair of the Foils,
task-25-20-72-6000-300-0801-a01].
TASK 25-20-72-000-0802-A01
5. Disassembly of the IAT Amrest
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-030-005-A01
(1) Removal of the IAT Amrest
(b) Remove the screws (4-230) from the bracket (4-210) and from the bumper sheet.
(e) Remove the IAT Armrest with the bushings (4-140) and (4-150) from the upper spreader.
SUBTASK 25-20-72-000-0004-A01
(2) Disassembly of the IAT Amrest
(a) Slide and remove the rear armcap (4-180) from the structure.
(b) Remove the armcap (4-190) with the screws (4-200) and washers (4-205) from the hinges
(4-70), (4-80).
(c) If the foils (4-160), (4-170) are damaged, remove they from the structure [refer from Repair
of the Foils, task-25-20-72-6000-300-0801-a01].
(d) Remove the IAT Table [refer to Removal and Disassembly of the IAT Table,
task-25-20-72-000-822-a01].
(e) Remove the brackets (4-50) with the screws (4-120) from the structure (4-20).
(f) Remove the spring (4-40) with slider (4-30) from the structure (4-20).
(g) Remove the guide (4-60) with two screw (4-110) from the structure.
(h) Remove the guide (4-62) with the screw (4-110) from the structure.
(i) Remove the slide plate (4-90) with the two screws (4-110) and two screws (4-120) from
the structure.
(j) Remove the rear hinge (4-70) with the screws (4-120) and the washers (4-65) from the
structure.
(k) Remove the front hinge (4-80) with the screws (4-120) and the washers (4-85) from the
structure.
(l) Remove the distance (4-25) with the screws (4-110) from the structure.
(m) Remove the rear beam [not a spare part] with the screws (4-110) and the spacer
(4-23) from the structure.
TASK 25-20-72-000-822-A01
6. Removal and Disassembly of the IAT Table
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-020-023-A01
(1) Removal of the IAT Table
(c) Slide and remove the IAT table (4-260) from the IAT Armrest (4-10).
SUBTASK 25-20-72-000-024-A01
(2) Disassembly of the IAT Table
(a) Remove the handle (5-110) with the screws (5-120) from the hinge (5-100).
(b) Remove the setscrews (5-140) in the pin (5-130) from the table plates.
(c) Remove the pins (5-130) from both table plates and from the hinge (5-100).
(d) Remove the hinge (5-100) with the screws (5-95) from the table plate.
(e) Remove the endstop (5-90) with the setscrews (5-155) from the table plate (5-80).
(f) Slide the assembled table arm (5-20) from the table plate (5-80).
(g) Remove the screws (5-95) from the table arm (5-20).
(h) Remove the carriage (5-60) with the screws (5-95) from the hinge arm (5-20).
(i) Remove the carriage (5-70) with the screws (5-95) from the hinge arm (5-20).
(j) Remove the screws (5-95) from the table arm (5-20) with the pin (5-50), the bearing
hinges (5-30) and the hinge arms (5-40).
(k) Remove the two carriages (5-70) with the screws (5-95) from the hinge arm (5-40).
(l) Remove the foils (5-170), (5-180), (5-160) from the structure [refer to Repair of the Foils,
task-25-20-72-6000-300-0801-a01].
TASK 25-20-72-000-0803-A01
7. Disassembly of the Backrest Module
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-000-0005-A01
(1) Disassembly of the Backrest Module
(a) Remove upper literature pocket (9-30) from the backrest shell assy (9-20).
(b) The backrest shell cover (9-40) is glued to the table attachment assy, refer to Replacement
of the Backrest Shell Cover, task-25-20-72-000-828-a01.
TASK 25-20-72-000-0805-A01
8. Disassembly of the Table Plate Assy
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-000-0006-A01
(1) Disassembly of the Table Arm Assy
(a) Align the table arm (8-80) through the backrest and remove the backrest module (8-130).
(b) Remove the hinge attachment (8-70) with the screws (8-200) from the backrest (8-10).
(c) Remove the hinge attachment (8-70) from the table arm (8-80).
(d) Remove the bolt (8-110) with bushings (8-150), (8-120), (8-150) and the insert
(8-100) from the table arm (8-80).
(e) Remove the hinge attachment (8-70) from the table arm (8-80).
SUBTASK 25-20-72-020-006-A01
(2) Removal of the Table Arm Assy from the Table
(a) Loosen and remove the setscrew (8-160) from the hinge attachment (8-70).
(b) Remove the end pin (8-130) and the groove screws (8-90).
(d) Slide the table arm (8-80) from the table plate.
TASK 25-20-72-000-825-A01
9. Removal of the Life Vest Pouch
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-000-026-A01
(1) Removal of the Lifevest Pouch
(a) Loosen the life vest pouch tape around the rear beam and close tape.
(b) Loosen the two press button straps around the front beam.
E. Close Up
Not applicable
TASK 25-20-72-000-0806-A01
10. Disassembly of the Set Spreader Foils
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-000-0008-A01
(1) Disassembly of the Spreader Foils
1 Remove the bumper (6-20) and the cover (6-40) with the screws (6A-20), (6A-30) from
the seat spreader
2 Remove the sheet (6-30), the cover (6-40) with the screws (6A-40) from the seat
spreader.
1 Remove the covers (6-20) with the screws (6A-20), the washers (6A-35) and the nuts
(6A-45) from the seat spreader.
1 Remove the bumper (6-20) and the cover (6-40) with the screws (6A-20), (6A-30) from
the seat spreader
2 Remove the sheet (6-30), the cover (6-40) with the screws (6A-40) from the seat
spreader.
TASK 25-20-72-000-0807-A01
11. Disassembly of the Set Armrest Attachment
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-000-0009-A01
(1) Removal of the Armrest
(a) Remove the locking plate (3-50) with the screw (3-60).
(b) Remove the armrest attachment set (3-10) with the bolt (3-20), washers (3-40) and new
spring loaded washer (3-30). Make sure that the spring loaded washer direction (3-30) is
correct.
(c) Remove the washer (3-70) from the armrest from opposite side of the seat spreader and
hold on.
SUBTASK 25-20-72-020-025-A01
(2) Removal of the Upper Spreader Cover (outbd)
(a) Remove the screw (7-40) with the bolt (3-20) from the covers.
(b) Remove the covers (7-20), (7-30) and the pin (7-50) from the seat spreader.
TASK 25-20-72-000-0808-A01
12. Removal and Disassembly of the Backrest
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-000-0010-A01
(1) Removal of the Backrest from the Primary Structure
(b) Move both bolts (15-30), (15A-30) from the centre until they are aligned with the inner side
of the backrest bearings.
(c) Move this bolt (15-30), (15A-30) approx. 20 mm [0.8 in.] into the seat centre of the seat
place where mechanical structure and backrest will be installed.
(d) Align the backrest structure assy (8-10) from the bushes (15-45), (15-50), (15A-45),
(15A-50), the bearings (15-40), (15A-40) with the opposite bolt (15-30).
(e) Slip the backrest structure assy (8-10) and the bushes (15-45), (15-50), (15A-45),
(15A-50), the bearings (15-40), (15A-40) on the bolt (15-30), (15A-30).
(f) Remove the bushes (15-45), (15-50), (15A-45), (15A-50) and the bearings (15-40),
(15A-40).
(h) Move one bolt (15-30), (15A-30) approx. 20 mm [0.8 in.] into the seat centre of the seat
place where mechanical structure and backrest will be installed.
SUBTASK 25-20-72-020-007-A01
(2) Removal of the Backrest Module Assy
(a) Remove the backrest shell cover (9-40), refer to Replacement of the Backrest Shell Cover,
task-25-20-72-000-828-a01
(b) Cut the cable ties (1-640), (1A-640), (1B-640), (1C-640) from the rear beam.
(c) Remove the push in rivets (1-560), (1A-560), (1B-560), (1C-560) from the backrest
module assy.
(d) Remove the screws (1-570), (1A-570), (1B-570), (1C-570) and washers (1-580), (1A-580),
(1B-580), (1C-580) from the backrest module assy.
(e) Remove the backrest module assy from the backrest structure.
TASK 25-20-72-000-824-A01
13. Disassembly of the Backrest Structure Attachment
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-000-025-A01
(1) Removal and Disassembly of the Backrest Structure Attachment
(a) Remove the LOK attachment, refer from Disassembly of the Lok Attachment ,
task-252072-3000-000-0809-a01.
(b) Remove the attachment (17A-20) from the backrest lever with the pin (17A-50).
TASK 25-20-72-000-0809-A01
14. Disassembly of the Lok Attachment
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-000-0011-A01
(1) Disassembly of the LOK-Attachment
(a) Remove the bearings (17-60) from the brackets (17-20), (17-30).
(b) Remove the brackets (17-30), (17-20) from the support (17-50).
SUBTASK 25-20-72-020-009-A01
(2) Removal of the LOK Attachment
(a) Remove the attachment (17A-20) with the quick release pin (17A-50) from the
backrest-fixation point of the backrest.
(b) Remove the bearing (17A-40) from the backrest-fixation point of the backrest.
(c) Remove the attachment (17A-20) with its threaded end from the support (17-50) (if
applicable remove the washers (17-65)) and loosen with the two locking nuts (17-70).
(d) Remove the pre-assembled part with the support (17-50) and the screws (17-80) (if
applicable (17-90), (17-100)) from the front tube.
TASK 25-20-72-000-0811-A01
15. Disassembly of the Toggle Attachment
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-000-0014-A01
(1) Disassembly of the Toggle Attachment
(b) Remove the screw (12-20) inside upper of the literature pocket [part of Backrest Module]
from the toggle (12-40).
(c) Remove the toggle (12-40) from the literature pocket [part of Backrest Module].
(d) Remove the bearing (12-30) the upper literature pocket [part of Backrest Module].
TASK 25-20-72-000-827-A01
16. Disassembly of the Primary Structure
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-000-028-A01
(1) Removal of the Tube
(b) Remove the tube (13A-120) with the support (13A-140) and the screws (13A-150) to the
seatlegs (13A-20).
TASK 25-20-72-000-0813-A01
17. Disassembly of the Seat Bottom
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-030-008-A01
(1) Disassembly of the Seat Bottom
SUBTASK 25-20-72-020-013-A01
(2) Removal of the Seat Bottom
(a) Remove the screws (15-110) and the nuts (15-120) of the spreader assy.
(b) Pull the opposite side of the front mounted seating pipe(10-20) into its pocket using the
Spanner Assy (5008800100000) from the front of the spreader assy.
(c) Remove one end of the front pipes (10-20) from the front of the spreader assy.
(d) Remove the other end of the pipes (10-20) from the spreader assy.
(e) Loosen one end of the pipe (10-20) at the aft of the seat spreader.
(f) Install the screws (15-110) and the nuts (15-120) of the spreader assy.
TASK 25-20-72-000-826-A01
18. Disassembly of the Reinforcement Assy
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-000-027-A01
(1) Disassembly of the Reinforcement Assy
(a) Remove the baggage bar (18-60) with the screw (18-100) from the diagonal reinforcement
(18-30).
(b) Remove the bolt (18-50) with the screw (18-70) from the lower diagonal reinforcement
(18-30).
(c) Remove the bolt (18-40) with the screw (18-90) from the upper diagonal reinforcement
(18-30).
SUBTASK 25-20-72-030-011-A01
(2) Removal of the Reinforcement Assy
(a) Remove the vertical reinforcement (18-20) with the screws (18-70) and (18-80) from the
diagonal reinforcement (18-30) and from the lower tube of the primary structure.
(b) Remove the vertical reinforcement (18-20) with the screws (18-70) and (18-80) from
the tube of the primary structure.
(c) Remove the diagonal reinforcement (18-30) with the screws (18-70) from the tube of the
primary structure.
TASK 25-20-72-000-0814-A01
19. Removal and Disassembly of the Seatleg Assy
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-020-004-A01
(1) Removal of the Seatleg from the Structure
(a) Remove the supports (14A-20) with the screws (14A-30), (14A-40), (14A-50) from the
seatleg assy (14-10).
SUBTASK 25-20-72-000-0017-A01
(2) Disassembly of the Seatleg
(a) Remove the rear fitting (14-80) from the rear seatleg (14-30).
1 Remove the hexagon cap nut (14-210) together with the washer (14-70).
2 Remove the bolt (14-200) together with the washer (14-70) from the rear seat leg.
3 Remove rear seat fitting (14-80) together with the washers (14-60) from the rear
seat leg.
1 Remove the front fitting (14-130) from the front seat leg (14-20).
a Remove the base body (14-140) with the nut (14-150) the locknut (14-160) and
the washers (14-170), (14-180).
b Remove the seat track cover (14-50) from the front seat leg (14-20).
2 Remove the seat track cover (14-50) from the rear seat leg (14-30) with the screw
(14-220).
(c) Remove the bar (14-40) with the screws (14-190) the washers (14-240), (14-250) and the
nuts (14-230) from the rear seatleg (14-30) and the front seatleg (14-20).
TASK 25-20-72-000-0816-A01
20. Disassembly of the Spreader Assy
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-020-014-A01
(1) Removal of the Spreader Assemblies
(a) Remove the support (15B-20), (15B-60) with the screws (15B-30) and (15B-40) from the
spreader assy (15-20) and from the primary structure.
SUBTASK 25-20-72-020-016-A01
(2) Removal of the Outer Spreader Assemblies (with Steward Step Attachment)
(a) Remove the screw (16-70) and the washer (16-90) from the baggage bar.
(b) Remove the bolt (16-40) with the screw (16-60) from the support (16-30).
(c) Remove the supports (16-20) and (16-30) with the screws (16-80) and (16-50) to the
spreader assy (15-20) and from the primary structure.
SUBTASK 25-20-72-030-002-A01
(3) Disassembly of the Center Spreader Assemblies (STD)
(a) Remove the screw (15A-110) and the nut (15A-120) from the seat spreader and from the
seat bottom .
(b) Remove the inner bolt (15A-30) with the bearing (15A-40) and the bushes
(15A-45)(15A-50) from the seat spreader (15A-20).
1 Remove the screw (15A-80), the seat belt limiters (15A-60), seat belt shackles
(15A-70), the washer (15A-90) with the nut (15A-100) from the seat spreader
(15A-20).
2 If applicable (Y-belt), remove the screw (15A-140), seat belt shackles (15A-70A),
the washer (15A-90A); (15A-150); (15A-160) with the nut (15A-100A) from the seat
spreader (15A-20).
(d) If necessary, remove the bearings (15A-130) from the spreader (15A-20).
SUBTASK 25-20-72-030-004-A01
(4) Disassembly of the Outer Spreader Assemblies (STD)
(a) Remove the screw (15-110) and the nut (15-120) from the seat spreader and from the
seat bottom .
(b) Remove the outer bolt (15-30) with the bearing (15-40) and the bushes (15-45),
(15-50) from the seat spreader (15-20).
1 Remove the screw (15-80), the seat belt limiter (15-60), seat belt shackle (15-70), the
washer (15-90) with the nut (15-100) from the seat spreader (15-20).
2 If applicable (Y-belt) , remove the screw (15-170), seat belt shackle (15-70A), the
washer (15-90A) with the nut (15-100A) from the seat spreader (15-20).
(d) If necessary, remove the bearings (15-130) from the spreader (15-20).
SUBTASK 25-20-72-030-010-A01
(5) Disassembly of the Aisle Spreader Assemblies (HC)
2 Remove the HC lever (15-140) and the spring (15-150) from the spreader.
(b) Remove the screw (15-110) and the nut (15-120) from the seat spreader and from the
seat bottom .
(c) Remove the outer bolt (15-30) with the bearing (15-40) and the bushes (15-45)(15-50) from
the seat spreader (15-20).
1 Remove the screw (15-80), the seat belt limiter (15-60), seat belt shackle (15-70), the
washer (15-90) and the nut (15-100) from the seat spreader (15-20).
2 If applicable (Y-belt) , remove the screw (15-170), seat belt shackle (15-70A), the
washer (15-90A) with the nut (15-100A) from the seat spreader (15-20).
(e) If necessary, remove the bearings (15-130) from the spreader (15-20).
TASK 25-20-72-000-0815-A01
21. Removal of the Baggage Bar
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-020-020-A01
(1) Removal of the Baggage Bar (STD)
(a) Remove the plug (1A-480), (1B-480), (1C-480), from the baggage bar.
(b) Remove the baggage bar with the clamp (11-20) and the screws (11-30) from the seatlegs.
(c) Remove the curved baggage bar with the screw (16-70) and the washer (16-90) from the
steward step assy.
(d) Remove the straight baggage bar and the curved baggage bar with the baggage bar
connector (1A-470), (1B-470), (1C-470).
TASK 25-20-72-000-0801-A01
22. Disassembly of the IFE Installation
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-000-0003-A01
(1) Installation of the IFE
(a) Remove the power connector with the screws (19-471) and the nuts (19-472) from the
primary structure.
(b) Remove the electric plates (19-20) with the mounting bridge (19-240) from the primary
structure.
(c) Remove the electrical equipment from the primary structure (refer to Schematic and
Wiring Diagrams, task-25-20-72-750-001-a01).
SUBTASK 25-20-72-030-012-A01
(2) Disassembly of the Shroud Assy
(a) Remove the cover (20-40) with the stud (20-50) from the shroud.
(b) Remove the quick fixation (20-130) from the shroud assy.
(c) Remove the disconnect bracket (20-90) with the screw (20-120) and the nut (20-110) from
the shroud assy.
SUBTASK 25-20-72-020-026-A01
(3) Removal of the Shroud
(a) Remove the cover (20-40) with the stud (20-50) from the shroud.
(b) Remove the screws (21-20) with the bushings (21-30) and washers (21-40) and nuts
(21-50) from the shroud assy.
(d) Remove the electrical equipment from the shroud assy (refer to Schematic and Wiring
Diagrams, task-25-20-72-750-001-a01).
(e) Attach the cover (20-40) with the stud (20-50) to the shroud.
SUBTASK 25-20-72-030-013-A01
(4) Disassembly of the ACOU Shroud Assy Rear
SUBTASK 25-20-72-020-027-A01
(5) Removal of the ACOU Shroud Assy Rear
(a) Remove the ACOU Shroud (22-10) from the rear seatleg.
(b) Remove the electrical equipment from the shroud assy (refer to Schematic and Wiring
Diagrams, task-25-20-72-750-001-a01).
(c) Remove the screws (23-20), (23-30) with the bushings (23-70), (23-80) and washers
(23-40) and nuts (23-50), (23-60) from the ACOU Shroud.
SUBTASK 25-20-72-030-014-A01
(6) Assembly of the ACOU Shroud Assy Front
(a) Remove the cable mount (24-30) with the screw (24-40).
SUBTASK 25-20-72-020-028-A01
(7) Removal of the ACOU Shroud Assy Rear
(a) Remove the electrical equipment from the shroud assy (refer to Schematic and Wiring
Diagrams, task-25-20-72-750-001-a01).
(b) Remove the supports (25-20) with screws (25-30) from the ACOU Shroud (24-10).
(c) Remove the ACOU Shroud (24-10) from the front beam.
INTENTIONALLY BLANK
CLEANING
TASK 25-20-72-100-001-A01
1. Cleaning
A. General
This page block gives a list of cleaning materials and instructions to clean the passenger seats.
B. SAFETY INFORMATION
WARNING: WHEN YOU USE SOLVENT TYPES OF CLEANING AGENTS, MAKE SURE THERE IS
A GOOD AIRFLOW IN THE AREA. DO NOT USE OZONE-DEPLETING CLEANERS,
USE ENVIRONMENTALLY FRIENDLY CHEMICALS. OBEY FIRE PRECAUTIONS
OF THE PRODUCT.
CAUTION: BECAUSE EACH CLEANING AGENT HAS SPECIFIC PROPERTIES AND YOU MAY
ONLY USE IT FOR SPECIAL TASKS, OBEY THE INSTRUCTIONS GIVEN ON ANY
PRODUCT CONTAINER AND THE SUPPLIER`S MATERIAL SAFETY DATA SHEET
TO GET THE BEST RESULTS. OBEY APPLICABLE INTERNATIONAL CHEMICAL
SAFETY CARDS (ICSC).
(1) Safety information helps you to prevent damage to personnel and material.
C. CLEANING INTERVALS
TASK 25-20-72-100-002-A01
2. Cleaning of the Passenger Seat
(1) Prevent contact with eyes. If you get cleaner in your eyes, flush the eyes thoroughly with water.
C. Job Set-Up
(1) Make a test on the surface before you use the cleaners.
D. Procedure
SUBTASK 25-20-72-100-002-A01
(1) Cleaning of the Upholstery
(b) Clean the dress covers with a upholstery shampoo. Dilute the upholstery shampoo as
recommended by the manufacturer.
(c) Clean the seat belts with soapy water only and rinse them with clean water.
(d) Clean the oil-type grease marks with a soft sponge and a soap or dilution of Isopropyl
alcohol.
SUBTASK 25-20-72-100-005-A01
(2) Cleaning of Plastics Parts
CAUTION: USE MILD SOAP ONLY FOR CLEANING OF PLASTIC PARTS. OTHERWISE THE
WARRANTY MAY BE VOID.
(a) Clean all plastic surfaces with a solution of mild soap and water.
(b) Apply the solution directly to the plastic surface and rinse it with clean water.
SUBTASK 25-20-72-100-006-A01
(3) Cleaning of the Metal Parts
(b) Clean the parts with a soap and water solution, or Isopropyl alcohol dilution.
SUBTASK 25-20-72-100-007-A01
(4) Removal of the Adhesive Residues
(a) Remove the adhesive residues with a Lint-free cloth soaked in Isopropyl alcohol dilution.
E. Close-Up
SUBTASK 25-20-72-100-003-A01
(1) Make sure that the surfaces are fully dry before use.
INTENTIONALLY BLANK
INSPECTION/CHECK
TASK 25-20-72-200-801-A01
1. General
This page block gives the procedures and criteria to show that the components are serviceable.
TASK 25-20-72-210-001-A01
2. Visual Inspection of Parts
Self explanatory
Not applicable
C. Job Set-Up
(1) Use a strong light and a magnification tool during the test to make sure that you have a
satisfactory view of all components.
D. Procedure
SUBTASK 25-20-72-200-001-A01
(1) Visual Inspection
(a) Inspect all new or existing parts before installing them on the seat. Use an inspection
mirror during inspection for damage or corrosion.
(b) Examine the seat for missing, loose, damaged or worn parts.
E. Close Up
Not applicable
TASK 25-20-72-200-802-A01
3. Passenger Seat Serviceability Inspection
Self explanatory
Not applicable
C. Job Set-Up
(1) Use a strong light and a magnification tool during the test to make sure that you have a
satisfactory view of all components.
(2) Do the tests that follow after any significant repair work or disassembly of the passenger seat.
Replace parts that do not meet the requirements of the tests with a serviceable part.
D. Procedure
SUBTASK 25-20-72-200-002-A01
(1) General Parts
(a) Examine if all parts are clean, free of cracks, corrosion, deterioration or other obvious
signs of wear and damage.
(b) Test the dimensions of the passenger seats, refer to Description and Operation,
task-252072-870-001-a01.
SUBTASK 25-20-72-200-003-A01
(2) Dress Covers and Foams
(b) Examine if the dress covers and cushions are correctly aligned.
(c) Examine the condition of dress covers and foam, especially for looseness, frayed edges
and loose seams.
SUBTASK 25-20-72-200-004-A01
(3) Seat Belts
(a) Examine the condition of all seat belts, especially for looseness, frayed edges and loose
seams.
SUBTASK 25-20-72-200-005-A01
(4) Backrest
(a) Examine the backrest functions (recline and upright) for correct action and clearance of
operation, refer to TESTING AND FAULT ISOLATION .
(b) Examine the correct function and installation of the backrest cylinder, refer to TESTING
AND FAULT ISOLATION .
(c) Make sure that there are no missing or broken parts and the parts correctly attached or
tightened.
SUBTASK 25-20-72-200-007-A01
(5) Armrest
SUBTASK 25-20-72-200-010-A01
(6) Backrest Table Attachment
(a) Make sure that the backrest table arm are correctly attached.
SUBTASK 25-20-72-200-008-A01
(7) Baggage Bar
(a) Examine the baggage bars for proper attachment to the seatlegs.
(b) Examine the parts for correct alignment, burrs and sharp edges.
SUBTASK 25-20-72-200-009-A01
(8) Lifevest
E. Close Up
Not applicable
INTENTIONALLY BLANK
REPAIR
TASK 25-20-72-300-801-A01
1. Repair
A. General
This page block gives a list of all materials necessary for repair of the passenger seat together with
repair procedures that agree with DISASSEMBLY . Refer to INSPECTION/CHECK for damage
limit criteria.
TASK 25-20-72-000-0801-A01
2. Adjustment of Backrest Table
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-820-001-A01
(1) Adjustment of Backrest Table
(a) The two set screw on the side of the table arm must be tightened in order to achieve the 3
degrees up compensation of the table.
SUBTASK 25-20-72-820-002-A01
(2) Adjustment of Backrest Table Attachment
(a) Adjust the backrest table arm with the backrest table attachment. Refer to Fig. 6001.
E. Close Up
Not applicable
TASK 25-20-72-000-828-A01
3. Replacement of the Backrest Shell Cover
Self explanatory
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-820-004-A01
(1) Removal of the Backrest Shell Cover
NOTE: The backrest shell cover is glued with Gyso Polyflex 444 (1103)
(b) If necessary, remove the backrest module assy, refer to Removal of the Backrest Module
Assy, subtask-25-20-72-020-007-a01
SUBTASK 25-20-72-820-003-A01
(2) Installation of the Backrest Shell Cover
(a) If necessary, install the backrest module assy, refer to Installation of the Backrest Module
Assy, subtask-25-20-72-420-022-a01
(b) Clean the backrest shell cover (9-40) and the table hinge attachment (8-70), refer to
Cleaning, task-252072-100-001-a01.
(c) Attach Gyso Polyflex 444 (1103) to the table hinge attachment (8-70).
(d) Carefully attach the backrest shell cover (9-40) to the backrest module assy.
DP029-252072-06000-05-01-00
E. Close Up
Not applicable
TASK 25-20-72-300-0801-A01
4. Repair of the Foils
Self explanatory
(1) Consumable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-300-005-A01
(1) Repair of Armrest Foil
NOTE: The repair of armrest foils is a destructive process. Therefor always left hand and right
hand foil has to be exchanged.
(a) Clean the area and attach the Loop Tape (0213).
(d) Apply new Double-Sided Adhesive Tape (0193), Double-Sided Adhesive Tape (0192)
stripes to the armrest structure.
(e) Remove all cover stripes from the double sided tape on the LH side of the armrest.
(f) Spray a thin film of Isopropanol (-) to the inner side of the LH Foil (2-60), (2A-60).
(g) Attach and press the LH (2-60), (2A-60), foil to the armrest structure.
(h) Remove all cover stripes from the double sided tape on the RH side of the armrest.
(i) Spray a thin film of Isopropanol (-) to the inner side of the RH Foil (2-70), (2A-70).
(j) Attach and press the RH (2-70), (2A-70) foil to the armrest structure.
(k) Apply Gyso Polyflex 444 (1103) in between the overlapping of the LH foil (2-60), (2A-60),
and the RH foil (2-70), (2A-70), for cold welding of the foils. Refer to Fig.6003 for the
illustration of the armrest with definition of the double sided tape.
B
A
2 4
25 mm
B A
NOTES:
1 DILUTOR HAKU 2091
DP029-252072-06000-03-01-00
SUBTASK 25-20-72-300-006-A01
(2) Repair of IAT box Foils
NOTE: The repair of armrest foils is a destructive process. Therefore always left hand and
right hand foil has to be exchanged.
(c) Spray a thin film of Isopropanol (-) to the inner side of the LH Cover (4-160).
(d) Apply Gyso Polyflex 444 (1103) to the structure, refer to Fig. 6004.
(e) Attach and press the LH cover (4-160) to the IAT structure.
(g) Spray a thin film of Isopropanol (-) to the inner side of the RH Cover (4-170).
(h) Apply Gyso Polyflex 444 (1103) to the structure, refer to Fig. 6004.
(i) Attach and press the RH cover (4-170) foil to the IAT structure.
(j) Apply Gyso Polyflex 444 (1103) in between the overlapping of the LH cover (4-160) and
the RH cover (4-170) for cold welding of the foils. Refer to Fig. 6004 for the illustration of
the IAT with definition of the double sided tape.
1 1
1
1
1
DP029-252072-06000-04-01-00
NOTES:
1 1
1
1
1
DP029-252072-06000-04-02-00
NOTES:
SUBTASK 25-20-72-300-007-A01
(3) Repair of FR Table foils
(c) Remove the cover stripes from the double sided tape on the backside of the foil.
(d) Spray a thin film of Isopropanol (-) on the back side of the foil.
(e) Attach the new foil to the table structure and adjust accordingly.
E. Close Up
Not applicable
INTENTIONALLY BLANK
ASSEMBLY
TASK 25-20-72-430-001-A01
1. Assembly
A. General
This page block includes a list of all materials necessary during assembly and the assembly
procedures for all parts disassembled during DISASSEMBLY .
(1) Before assembly, do the CLEANING , INSPECTION/CHECK and the REPAIR of all components.
TASK 25-20-72-400-801-A01
2. Assembly of the Fixed Armrest
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-007-A01
(1) Assembly of the Fixed Armrest
(b) Install the foils (2-60), (2-70) to the structure [refer to Repair of the Foils,
task-25-20-72-6000-300-0801-a01].
(d) Attach the front cap (2-40) with the screw (2-50) to the structure.
(f) Install the screw (2-120) and the washer (2-110) in the structure and fasten the armcap.
TASK 25-20-72-400-802-A01
3. Assembly of the Movable Armrest
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-006-A01
(1) Assembly of the Movable Armrest
(b) Install the foils (2A-60); (2A-70) to the structure [refer to Repair of the Foils,
task-25-20-72-6000-300-0801-a01].
(d) Attach the front cap (2A-40) with the screw (2A-50) to the structure.
(f) Install the screw (2A-120) and the washer (2A-110) in the structure and fasten the armcap.
TASK 25-20-72-400-804-A01
4. Assembly and Installation of the IAT Amrest
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-004-A01
(1) Assembly of the IAT Amrest
(a) Install the rear beam [not a spare part] with the screws (4-110) and the spacer (4-23) in
the structure.
(b) Install the distance (4-25) with the three screws (4-110) in the structure.
(c) Attach the rear hinge (4-70) with the screws (4-120) and the washers (4-65) to the
structure.
(d) Attach the front hinge (4-80) with the screws (4-120) and the washers (4-85) to the
structure.
(e) Attach the slide plate (4-90) with the two screws (4-110) and two screws (4-120) to the
structure.
(f) Attach the guide (4-60) with two screw (4-110) to the structure.
(g) Attach the guide (4-62) with the screw (4-110) to the structure.
(h) Install the spring (4-40) with slider (4-30) to the structure (4-20).
(i) Install the brackets (4-50) with the screws (4-120) to the structure (4-20).
(j) Install the IAT table [refer to Assembly and Installation of the IAT Table,
task-25-20-72-400-805-a01].
(k) If removed, attach the foils (4-160), (4-170) to the structure [refer to Repair of the Foils,
task-25-20-72-6000-300-0801-a01].
(l) Attach the armcap (4-190) with the screws (4-200) and washers (4-205) to the hinge.
(m) Slide and attach the rear armcap (4-180) to the structure.
SUBTASK 25-20-72-420-001-A01
(2) Installation of the IAT Amrest
(a) Install the IAT Armrest with the bushings (4-140) and (4-150) to the upper spreader.
(d) Install the screws (4-230) to the bracket (4-210) and to the bumper sheet.
TASK 25-20-72-400-805-A01
5. Assembly and Installation of the IAT Table
Self explanatory
(1) Consumable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-008-A01
(1) Assembly of the IAT Table
(a) Attach the foils (5-170), (5-180), (5-160) to the structure [refer to Repair of the Foils,
task-25-20-72-6000-300-0801-a01].
(c) Attach the two carriages (5-70) with the screws (5-95) to the hinge arm (5-40).
(e) Install the pin (5-50) to the bearing hinges (5-30) in the hinge arm (5-40) and install to the
in the table arm (5-20) with the screws (5-95).
(g) Attach the carriage (5-70) with the screws (5-95) to the hinge arm (5-20).
(h) Attach the carriage (5-60) with the screws (5-95) to the hinge arm (5-20).
(l) Slide the assembled table arm (5-20) in the table plate (5-80).
(m) Install the endstop (5-90) with the setscrews (5-155) in the table plate (5-80).
(o) Attach the hinge (5-100) with the screws (5-95) to the table plate.
(p) Attach both table plates to the hinge (5-100) with the pins (5-130).
(q) Install the setscrews (5-140) in the pin (5-130) to the table plates.
(s) Attach the handle (5-110) with the screws (5-120) to the hinge (5-100).
SUBTASK 25-20-72-420-025-A01
(2) Installation of the IAT table
(a) Slide and install the IAT table (4-260) in the structure (4-20).
(c) Install the setscrews (4-130) in the endstop (4-100) and to the brackets (4-50).
TASK 25-20-72-400-806-A01
6. Assembly of the Backrest Module
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-005-A01
(1) Assembly of the Backrest Module
(a) Install the upper literature pocket (9-30) to the backrest shell assy (9-20).
(b) The backrest shell cover (9-40) is glued to the table attachment assy, refer to Replacement
of the Backrest Shell Cover, task-25-20-72-000-828-a01.
TASK 25-20-72-400-809-A01
7. Assembly and Installation of the Table Plate Assy
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-001-A01
(1) Assembly of the Table Arm Assy
(a) Attach the hinge attachment (8-70) to the table arm (8-80).
(b) Install the bolt (8-110) with bushings (8-150), (8-120), (8-150) and the insert (8-100) to
the table arm (8-80).
(c) Attach the hinge attachment (8-70) in the table arm (8-80).
(d) Install the hinge attachment (8-70) with the screws (8-200) to the backrest (8-10).
(e) Align the table arm (8-80) through the backrest and install the backrest module (8-130).
SUBTASK 25-20-72-420-002-A01
(2) Installation of the Table Arm Assy to the Table Plate
(a) Install the end pin (8-130) and secure with the groove screws (8-90).
(b) Slide the table arm (8-80) in the table plate and secure with the setscrew (8-170).
TASK 25-20-72-400-810-A01
8. Assembly of the Set Spreader Foils
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-011-A01
(1) Assembly of the Aisle Spreader Foils
1 Attach the sheet (6-30) cover (6-40) with the screws (6A-40) to the seat spreader.
2 Attach the bumper (6-20) and the cover (6-40) with the screws (6A-20), (6A-30) to
the seat spreader
1 Attach the covers (6-20) with the screws (6A-20), the washers (6A-35) and the nuts
(6A-45) to the seat spreader.
1 Attach the sheet (6-30) cover (6-40) with the screws (6A-40) to the seat spreader.
2 Attach the bumper (6-20) and the cover (6-40) with the screws (6A-20), (6A-30) to
the seat spreader
TASK 25-20-72-400-823-A01
9. Installation of the Lifevest Pouch
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-024-A01
(1) Installation of the Life Vest Pouch
(b) Fasten the life vest pouch tape around the rear beam and close tape.
(c) Fasten the two press button straps around the front beam.
E. Close Up
Not applicable
TASK 25-20-72-400-811-A01
10. Assembly of the Set Armrest Attachment and Upper Spreader Cover
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-420-005-A01
(1) Installation of the Armrest
(b) Attach the washer (3-70) in the armrest to opposite side of the seat spreader and hold on.
(c) Install the armrest attachment set (3-10) with the bolt (3-20), washers (3-40) and new
spring loaded washer (3-30). Make sure that the spring loaded washer direction (3-30) is
correct.
(d) Install the locking plate (3-50) with the screw (3-60).
(e) Torque the bolt (3-20) (refer to Special Torque Value Table, task-252072-820-002-a01).
NOTE: Torque the armrest attachment set (3-10) that much that the armrest will not
fall off through its own weight.
SUBTASK 25-20-72-420-028-A01
(2) Installation of the Upper Spreader Cover (outbd)
(b) Attach the covers (7-20), (7-30) and the pin (7-50) to the seat spreader.
(c) Install the screw (7-40) with the bolt (3-20) in the covers.
TASK 25-20-72-400-821-A01
11. Installation and Assembly of the Backrest
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-420-021-A01
(1) Installation of the Backrest to the Primary Structure
(a) Move one bolt (15-30), (15A-30) approx. 20 mm [0.8 in.] into the seat centre of the seat
place where mechanical structure and backrest will be installed.
(c) Attach the bushes (15-45), (15-50), (15A-45), (15A-50) and the bearings (15-40), (15A-40).
(d) Slip the backrest structure assy (8-10) and the bushes (15-45), (15-50), (15A-45),
(15A-50), the bearings (15-40), (15A-40) on the bolt (15-30), (15A-30).
(e) Align the backrest structure assy (8-10) to the bushes (15-45), (15-50), (15A-45),
(15A-50) the bearings (15-40), (15A-40) with the opposite bolt (15-30), (15A-30).
(f) Move this bolt (15-30), (15A-30) approx. 20 mm [0.8 in.] into the seat centre of the seat
place where mechanical structure and backrest will be installed.
(g) Move both bolts (15-30), (15A-30) to the centre until they are aligned with the inner side
of the backrest bearings.
SUBTASK 25-20-72-420-022-A01
(2) Installation of the Backrest Module Assy
(a) Attach the backrest module assy with the screws (1-570), (1A-570), (1B-570),
(1C-570) and washers (1-580), (1A-580), (1B-580), (1C-580) to the backrest structure.
(b) Torque the screws (1-570), (1A-570), (1B-570), (1C-570) [refer to Special Torque Value
Table, task-252072-820-002-a01].
(c) Install the push in rivets (1-560), (1A-560), (1B-560), (1C-560) to the backrest structure.
(d) Attach the cable ties (1-640), (1A-640), (1B-640), (1C-640) through the backrest module
assy to the rear beam.
(e) Install the backrest shell cover (9-40), refer to Replacement of the Backrest Shell Cover,
task-25-20-72-000-828-a01
TASK 25-20-72-400-812-A01
12. Assembly of the Backrest Structure Attachment
Self explanatory
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-012-A01
(1) Assembly and Installation of the Backrest Structure Attachment
(a) Install the bearing (17A-40) from the backrest-fixation point of the backrest.
(b) Install the tube (17A-20) with the quick release pin (17A-50) in the backrest-fixation point
of the backrest.
(c) Install the tube (17A-20) with its threaded end from the support (17-TBD) (if applicable
remove the washers (17-TBD)) and loosen with the two locking nuts (17-TBD).
(d) Install the pre-assembled part with the support (17-40) and the screws (17-80) from
the front tube.
(e) Install the LOK attachment, refer to Disassembly of the Lok Attachment ,
task-252072-3000-000-0809-a01.
TASK 25-20-72-400-813-A01
13. Assembly of the Lok Attachment
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-014-A01
(1) Assembly of the LOK-Attachment
SUBTASK 25-20-72-420-003-A01
(2) Installation of the LOK Attachment
(a) For the installation position of the lok attachment (17-10), refer to the mark of disassembly.
(b) Attach the pre-assembled part with the support (17-40) and the screws (17-80) (if
applicable (17-90), (17-100)) to the front supporting tube. Torque the screws (refer to
Special Torque Value Table, task-252072-820-002-a01).
(c) Attach the attachment (17A-20) with its threaded end to the support (17-50) (if applicable
attach the washers (17-65)) and fasten with the two locking nuts (17-70).
(d) Install the bearing (17A-60) in the backrest-fixation point of the backrest.
(e) Attach the attachment (17A-20) with the quick release pin (17A-50) in the backrest-fixation
point of the backrest.
TASK 25-20-72-400-824-A01
14. Assembly of the Primary Structure
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-420-027-A01
(1) Installation of the Tube
(a) Install the tube (13A-120) with the support (13A-140) and the screws (13A-150) to the
seatlegs (13A-20).
TASK 25-20-72-400-815-A01
15. Assembly of the Toggle Attachment
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-420-010-A01
(1) Assembly of the Toggle Attachment
(a) Install the bearing (12-30) the upper literature pocket [part of Backrest Module].
(c) Install the toggle (12-40) to the literature pocket [part of Backrest Module].
(d) Install the screw (12-20) inside upper of the literature pocket [part of Backrest Module] to
the toggle (12-40).
TASK 25-20-72-400-822-A01
16. Assembly of the Main Seat Assemblies
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D.
SUBTASK 25-20-72-420-023-A01
(1) Installation of the Seat Belt
(a) Push the seat belt shackle together and attach seat belt (1-380), (1-390), (1-400),
(1A-380), (1A-390), (1A-400), (1B-380), (1B-390), (1B-400), (1C-380), (1C-390),
(1C-400) to the seat belt shackles.
SUBTASK 25-20-72-420-024-A01
(2) Installation of the Dress Cover and Cushions
(a) Attach the headrest cushion (1-280), (1-290), (1-300), (1A-280), (1A-290), (1A-300),
(1B-280), (1B-290), (1B-300), (1C-280), (1C-290), (1C-300) to the backrest structure.
(b) Attach the backrest dress cover (1-250), (1-260), (1-270), (1A-250), (1A-260), (1A-270),
(1B-250), (1B-260), (1B-270), (1C-250), (1C-260), (1C-270) to the backrest structure.
(c) Attach the seat cushion (1-190), (1-200), (1-210), (1A-190), (1A-200), (1A-210), (1B-190),
(1B-200), (1B-210), (1C-190), (1C-200), (1C-210) with the seat dress cover (1-220),
(1-230), (1-240), (1A-220), (1A-230), (1A-240), (1B-220), (1B-230), (1B-240), (1C-220),
(1C-230), (1C-240).
TASK 25-20-72-400-819-A01
17. Assembly of the Seat Bottom
Self explanatory
(1) Tool
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-017-A01
(1) Assembly of the Seat Bottom
SUBTASK 25-20-72-420-004-A01
(2) Installation of the Seat Bottom
(b) Stick one end of the pipe (10-20) at the aft of the seat spreader.
(c) Install the other end of the pipes (10-20) to the spreader assy.
(d) Install one end of the front pipes (10-20) to the front of the spreader assy.
(e) Pull the opposite side of the front mounted seating pipe (10-20) into its pocket using the
Spanner Assy (5008800100000) to the front of the spreader assy.
(f) Install and tighten the screws (15-110) and the nuts (15-120) of the spreader assy.
TASK 25-20-72-400-816-A01
18. Assembly and Installation of the Seatleg Assy
Self explanatory
(1) Consumable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-015-A01
(1) Assembly of the Seatleg
(a) Attach the bar (14-40) with the screws (14-190) the washers (14-240), (14-250) and the
nuts (14-230) to the rear seatleg (14-30) and the front seatleg (14-20).
2 Attach the seat track cover (14-50) to the rear seat leg (14-30) with the screw (14-220).
5 Attach the front fitting (14-130) to the front seat leg (14-20).
a Attach the seat track cover (14-50) to the front seat leg (14-20).
c Attach the base body (14-140) with the nut (14-150) the locknut (14-160) and the
washers (14-170), (14-180).
(c) Install the rear fitting (14-80) to the rear seatleg (14-30).
1 Attach rear seat fitting (14-80) together with the washers (14-60) to the rear seat leg.
2 Attach the bolt (14-200) together with the washer (14-70) to the rear seat leg.
3 Attach the hexagon cap nut (14-210) together with the washer (14-70).
4 Fasten the hexagon cap nut (14-210). Make sure that the bolt (14-200) can be rotated
easily and the washers (14-70) are not compressed.
SUBTASK 25-20-72-420-012-A01
(2) Installation of the Seatleg to the Structure
(a) Attach the supports (14A-20) with the screws (14A-30), (14A-40), (14A-50) to the seatleg
assy (14-10).
(b) Torque the screws (14A-30), (14A-40), (14A-50) (refer to Special Torque Value Table,
task-252072-820-002-a01).
E. Close Up
Not applicable
TASK 25-20-72-400-817-A01
19. Assembly and Installation of the Spreader Assy
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-016-A01
(1) Assembly of the Center Spreader Assemblies (STD)
1 Install the screw (15A-80), the seat belt limiter (15A-60), seat belt shackle (15A-70),
the washer (15A-90) with the nut (15A-100) in the seat spreader (15A-20).
2 If applicable (Y-belt), install the screw (15A-140), seat belt shackle (15A-70A),
the washer (15A-150), (15A-160), (15A-90A) with the nut (15A-100A) in the seat
spreader (15A-20).
3 Torque the screw (15A-80), (15A-140) (refer to Special Torque Value Table,
task-252072-820-002-a01).
(c) Install the outer bolt (15-30) with the bearing (15-40) and the bushes (15-45), (15-50) in
the seat spreader (15-20).
(d) Install the screw (15-110) and the nut (15-120) in the seat spreader and to the seat bottom.
SUBTASK 25-20-72-430-022-A01
(2) Assembly of the Outer Spreader Assemblies (STD)
1 Install the screw (15-80), the seat belt limiter (15-60), seat belt shackle (15-70), the
washer (15-90) with the nut (15-100) in the seat spreader (15-20).
2 If applicable (Y-belt), install the screw (15-170), seat belt shackle (15-70), the washer
(15-90A) with the nut (15-100A) in the seat spreader (15-20).
3 Torque the screws (15-80); (15-170) (refer to Special Torque Value Table,
task-252072-820-002-a01).
(c) Install the outer bolt (15-30) with the bearing (15-40) and the bushes (15-45), (15-50) in
the seat spreader (15-20).
(d) Install the screw (15-110) and the nut (15-120) in the seat spreader and to the seat bottom.
SUBTASK 25-20-72-430-019-A01
(3) Assembly of the Aisle Spreader Assemblies (HC)
1 Install the screw (15-80), the seat belt limiter (15-60), seat belt shackle (15-70), the
washer (15-90) with the nut (15-100) in the seat spreader (15-20).
2 If applicable (Y-belt), install the screw (15-170), seat belt shackle (15-70), the washer
(15-90A) with the nut (15-100A) in the seat spreader (15-20).
(c) Install the outer bolt (15-30) with the bearing (15-40) and the bushes (15-45), (15-50) in
the seat spreader (15-20).
(d) Install the screw (15-110) and the nut (15-120) in the seat spreader and to the seat bottom.
1 Install the spring (15-150) and the HC lever (15-140) to the seat spreader (15-20).
2 Install the pin (15-160) in the seat spreader and to the HC lever (15-140).
SUBTASK 25-20-72-420-014-A01
(4) Installation of the Spreader Assemblies
(b) Attach the support (15B-20), (15B-60) with the screws (15B-30) and (15B-40) to the
spreader assy and to the primary structure.
(c) Torque the screws (15B-30) and (15B-40) [ Special Torque Value Table,
task-252072-820-002-a01].
SUBTASK 25-20-72-420-018-A01
(5) Installation of the Outer Spreader Assemblies (with Steward Step Attachment)
(b) Attach the supports (16-20) and (16-30) with the screws (16-80) and (16-50) to the
spreader assy and to the primary structure.
(c) Torque the screws (16-80) and (16-50) [ Special Torque Value Table,
task-252072-820-002-a01].
(e) Attach the bolt (16-40) with the screw (16-60) to the support (16-30).
(f) Attach the screw (16-70) and the washer (16-90) with a plastic bag to the support.
E. Close Up
Not applicable
TASK 25-20-72-430-002-A01
20. Assembly and Installation of the Reinforcement Assy
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-430-025-A01
(1) Assembly of the Reinforcement Assy
(a) Attach the bolt (18-40) with the screw (18-90) to the upper diagonal reinforcement (18-30).
(b) Attach the bolt (18-50) with the screw (18-70) to the lower diagonal reinforcement (18-30).
(c) Install the baggage bar (18-60) with the screw (18-100) in the diagonal reinforcement
(18-30).
SUBTASK 25-20-72-420-026-A01
(2) Installation of the Reinforcement Assy
(a) Attach the vertical reinforcement (18-20) with the screws (18-70) and (18-80) to the
diagonal reinforcement (18-30) and to the lower tube of the primary structure.
(b) Attach the vertical reinforcement (18-20) with the screws (18-70) and (18-80) to the tube
of the primary structure.
(c) Attach the diagonal reinforcement (18-30) with the screws (18-70) to the tube of the
primary structure.
(d) Torque the screws (18-70), (18-80) [ Special Torque Value Table,
task-252072-820-002-a01]
E. Close Up
Not applicable
TASK 25-20-72-400-820-A01
21. Installation of the Baggage Bar
Self explanatory
(1) Consumable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-420-019-A01
(1) Installation of the Baggage Bar (STD)
(a) Attach the straight baggage bar and the curved baggage bar with the baggage bar
connector (1A-470), (1B-470), (1C-470).
(c) Attach the curved baggage bar with the screw (16-70) and the washer (16-90) to the
steward step assy.
(e) Attach the baggage bar with the clamp (11-20) and the screws (11-30) to the seatlegs.
(f) Attach the plug (1A-480), (1B-480), (1C-480), to the baggage bar.
E. Close Up
Not applicable
TASK 25-20-72-400-825-A01
22. Installation of the IFE Installation
Self explanatory
(1) Consumable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-420-035-A01
(1) Installation of the IFE
(a) Attach the electric plates (19-20) with the mounting bridge (19-240) to the primary
structure.
(b) Install the electrical equipment to the shroud assy (refer to Schematic and Wiring
Diagrams, task-25-20-72-750-001-a01).
(c) Install the power connector with the screws (19-471) and the nuts (19-472) to the primary
structure.
SUBTASK 25-20-72-420-029-A01
(2) Assembly of the Shroud Assy
(a) If necessary attach the edge protection (20-70), (20-80), (20-100) with Loctite 454 (1051).
(b) Attach the disconnect bracket (20-90) with the screw (20-120) and the nut (20-110) to
the shroud assy.
(d) Attach the cover (20-40) with the stud (20-50) to the shroud.
SUBTASK 25-20-72-420-030-A01
(3) Installation of the Shroud
(a) Remove the cover (20-40) with the stud (20-50) from the shroud.
(b) Install the electrical equipment to the shroud assy (refer to Schematic and Wiring
Diagrams, task-25-20-72-750-001-a01).
(d) Install the screws (21-20) with the bushings (21-30) and washers (21-40) and nuts
(21-50) to the shroud assy.
(e) Attach the cover (20-40) with the stud (20-50) to the shroud.
SUBTASK 25-20-72-420-031-A01
(4) Assembly of the ACOU Shroud Assy Rear
(a) If necessary attach the edge protection (22-20) with Loctite 454 (1051).
SUBTASK 25-20-72-420-032-A01
(5) Installation of the ACOU Shroud Assy Rear
(b) Install the electrical equipment to the shroud assy (refer to Schematic and Wiring
Diagrams, task-25-20-72-750-001-a01).
(c) Install the screws (23-20), (23-30) with the bushings (23-70), (23-80) and washers
(23-40) and nuts (23-50), (23-60) to the ACOU Shroud.
SUBTASK 25-20-72-420-033-A01
(6) Assembly of the ACOU Shroud Assy Front
(a) If necessary attach the edge protection (24-20) with Loctite 454 (0100).
(b) Install the cable mount (24-30) with the screw (24-40).
SUBTASK 25-20-72-420-034-A01
(7) Installation of the ACOU Shroud Assy Rear
(a) Install the electrical equipment to the shroud assy (refer to Schematic and Wiring
Diagrams, task-25-20-72-750-001-a01).
(c) Install the supports (25-20) with screws (25-30) to the ACOU Shroud (24-10).
E. Close Up
Not applicable
INTENTIONALLY BLANK
TASK 25-20-72-820-001-A01
1. General
This page block gives fits and clearances data and torque values. It is not necessary to measure the
sleeves, bushes etc. Standard torque-values are applicable, unless otherwise specified as below in the
table.
TASK 25-20-72-820-002-A01
2. Special Torque Value Table
TASK 25-20-72-94B-001-A01
1. General
This page block lists all special tools, fixtures, equipment and consumables necessary for the maintenance
actions given in the other page blocks.
TASK 25-20-72-94B-002-A01
2. Special Tools, Fixtures and Equipment
A. No special fixtures or specific equipment is necessary for maintenance or overhaul works on the seat
assies. However, we recommend that you use a simulated mounting track as support of the seat
assy during repair or transportation.
NOTE: You can use equivalent alternatives for the item listed below.
SPECIAL TOOLS
Table 9001
TASK 25-20-72-940-0801-A01
3. Consumables
CONSUMABLES
Table 9002
CONSUMABLES
Table 9002 (continued)
CONSUMABLES
Table 9002 (continued)
INTENTIONALLY BLANK
REMOVAL
TASK 25-20-72-010-801-A01
1. General
This page block gives data on how to remove the seat assies from the aircraft.
TASK 25-20-72-010-802-A01
2. Removal of the Passenger Seat from the Aircraft
Self explanatory
B. Job Set-Up
Not applicable
Not applicable
D. Procedure
SUBTASK 25-20-72-010-012-A01
(1) Removal of the Passenger Seat from the Seat Track
CAUTION: DO NOT SLIDE THE SEAT ASSY ACROSS ABRASIVE SURFACES. THIS WILL
CAUSE WEAR ON THE FRONT FITTING AND REAR FITTING.
The seat assies are attached to the mounting tracks of the aircraft with a front stud located at
the bottom of the front seatleg and the rear fitting located at the bottom of the rear seatleg.
(a) Loosen the nut at the front fitting with the Hook wrench DIN 1810-A30-32 (1002).
(d) Push the nut of the rear fitting, so that the pin goes into the slot.
(e) Turn the nut again in CCW direction to the lock the pin in the slot.
(f) Move the seat assy 1/2 inch forward or aft and lift it out of the mounting tracks.
Front seatleg
Fitting cap
Fitting Screw
DP029-252068-12000-01-01-00
E. Close Up
Not applicable
TASK 25-20-72-010-803-A01
3. Removal of the Line Replacement Parts
Self explanatory
B. Job Set-Up
Not applicable
Not applicable
D. Procedure
SUBTASK 25-20-72-010-013-A01
(1) Removal of the In-Seat-Harness
Refer to SCHEMATIC AND WIRING DIAGRAMS
SUBTASK 25-20-72-020-029-A01
(2) Removal of the USBPS
Refer to SCHEMATIC AND WIRING DIAGRAMS
(b) Remove the ground strap from the ground stud of the USBPS.
SUBTASK 25-20-72-020-030-A01
(3) Removal of the AC-Outlet Unit from the Shroud
Refer to SCHEMATIC AND WIRING DIAGRAMS
(a) Loosen the two hex screws from the AC-outlet unit until the screw movement is blocked.
SUBTASK 25-20-72-020-031-A01
(4) Removal of the In-Use-Light
E. Close Up
Not applicable
INTENTIONALLY BLANK
INSTALLATION
TASK 25-20-72-410-803-A01
1. General
This page block gives data on how to install the seat assies in the aircraft.
TASK 25-20-72-410-804-A01
2. Installation of the Passenger Seat to the Aircraft
Self explanatory
(1) Tools
C. Job Set-Up
(1) Clean the mounting tracks, studs and fittings before installation of the seat. This will prevent
unwanted wear of these parts.
D. Procedure
SUBTASK 25-20-72-410-001-A01
(1) Installation of the Passenger Seat to the Aircraft
(a) Lift the plunger and the secured screw (refer to Fig. 13001).
(b) Push the front fitting and rear fitting at the same time into the mounting tracks of the aircraft
(c) Tighten the nut of the front fitting below the front seatleg with the Hook wrench DIN
1810-A30-32 (1002) hand-tight +1/4 turn.
(e) Turn the nut of the rear fitting in CW direction to unlock the pin in the slot.
(f) Turn the nut again in CW direction until it stops on the slot.
(g) Tighten the fitting screw so that the fitting screw fits into the fitting cap to a special torque
value (refer to Special Torque Value Table, task-252072-820-002-a01)
Fitting cap
Fitting Screw
Front seatleg
Top of track
Fitting screw
DP029-252068-13000-01-01-00
E. Close Up
Not applicable
TASK 25-20-72-410-805-A01
3. Installation of the Line Replacement Parts
Self explanatory
C. Job Set-Up
D. Procedure
SUBTASK 25-20-72-410-002-A01
(1) Installation of the USB to the AC Outlet Shroud
Refer to SCHEMATIC AND WIRING DIAGRAMS
(b) Put the USB with the pigtail first into the AC-outlet shroud.
(c) Push the USB into the cutout and make sure, that the USB unit engage in its position.
(d) Fasten the two hex screws of the USB until it is properly fixed [Torque the two hex screws
with 0.33 to 0.56 Nm (3 to 5 lbf.in).
(e) Attach the front plate to the USB and fasten the hex screw.
SUBTASK 25-20-72-410-003-A01
(2) Installation of the USBPS
Refer to SCHEMATIC AND WIRING DIAGRAMS
(a) Fasten the USPS into the shroud by pushing the four Nylatches [Torque the Nylatches
max. 2.8 Nm (25 lbf.in)].
SUBTASK 25-20-72-410-005-A01
(3) Installation of the In-Use-Light
SUBTASK 25-20-72-410-004-A01
(4) Installation of the In-Seat-Harness
Refer to SCHEMATIC AND WIRING DIAGRAMS
NOTE: Use the defective harness as an example for the position of the green sleeve.
NOTE: If the green sleeve is not damaged, reuse the green sleeve.
(e) If possible, make a functional test of the seat to eliminate all failures.
E. Close Up
Not applicable
INTENTIONALLY BLANK
TASK 25-20-72-500-001-A01
1. General
This page block gives the requirements for transportation, special handling, packaging, storage and
preservation of the unit after assembly or test.
TASK 25-20-72-550-001-A01
2. Packing of the Passenger Seat
Self explanatory
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-550-001-A01
(1) Packing
NOTE: The seat assemblies are largely corrosion-resistant. Thus, under ordinary storage
conditions no special preservation materials are necessary.
(a) Identify the packaged seats by writing the assembly part number, serial number and repair
date. The data that follows is necessary on the unit:
1 Part Number
2 Nomenclature
3 Quantity
E. Close Up
Not applicable
TASK 25-20-72-550-002-A01
3. Storage of the Passenger Seat
Not applicable
C. Job Set-Up
Not applicable
D. Procedure
SUBTASK 25-20-72-550-002-A01
(1) Storage
(c) Make sure that there are no fumes that can cause damage to the seats.
(d) Keep the seats away from any heat source or direct sunlight.
E. Close Up
Not applicable
TASK 25-20-72-550-003-A01
4. Transportation of the Passenger Seat
Self explanatory
CAUTION: PUT DOWN THE SEAT ON THE BOTH LEGS AT THE SAME TIME. DO NOT PUT
DOWN THE SEAT ABRUPTLY OR ON ONLY ONE LEG, IT MAY CAUSE DAMAGE
TO THE SEAT. BE CAREFUL
(1) For seats heavier than 70 lbs. obey the lifting points. Only these lifting points are to be used for
lifting the seat.
DP029-252072-15000-01-01-00
C. Job Set-Up
D. Procedure
SUBTASK 25-20-72-550-003-A01
(1) Transportation
(a) Fix the passenger seats so that they do not move during transportation.
E. Close Up
Not applicable
INTENTIONALLY BLANK
1. IPL Introduction
A. General
This Illustrated Parts List (IPL) gives illustrations and a breakdown of all assemblies that can be
disassembled, repaired or replaced and reassembled.
2. Material Arrangement
A. Introduction
The introduction has all explanatory information about the individual sections that are necessary for
use of this IPL. Subsequently, the introduction has a list of abbreviations used in the Detailed Parts
List as well as a list of manufacturer codes, names and addresses.
B. Alpha/Numerical Index
(1) This section has a list of part numbers of all items recorded in the Detailed Parts List.
These part numbers are put in alpha-numerical sequence and are cross referenced to the
respective Figure/Item Numbers and to the number of units per assembly.
(2) The part number sequence starts at the leftmost (first) position as follows:
— numerals 0 through 9.
— a dash,
— numerals 0 through 9.
(a) The first number in the first line of a page shows the number of the Figure that illustrates
the part, the second number shows the item number by which you can find the part on the
illustration. A dash placed before the item number indicates that the part is not illustrated.
(a) The Part Number column has the original manufacturer's part number. When a part
number has been allocated to a "bought in" item, this ident number is also shown in
the Nomenclature column.
1 The indenture system shows the relationship of parts and assemblies to next higher
assemblies or installations, as follows:
1 2 3 4 5 6 7
Assembly or installation assembly RF number
Attaching parts for assembly or installation
***
Detailed part for assembly
Sub-assembly
Attaching parts for sub-assembly
***
Detailed parts for sub-assembly
Sub-sub-assembly
Attaching parts for sub-sub-assembly
***
Detailed parts for sub-sub-assembly etc.
1 Attaching Parts are captioned ATTACHING PARTS and are listed immediately after
the parts attached.
2 The *** symbol follows the last item of the attaching parts group.
(a) The Effectivity Code column establishes parts relationship with units or assemblies
which are essentially the same but have minor deviations. These units or assemblies
are assigned with reference letters such as A, B, C, etc. Parts which are not common
to all configurations but are associated with one or more of the coded lead items, carry
the letter or letters assigned to the lead item with which it is associated. Where a part is
common to all lead items, the effectivity column is left blank.
(a) This column contains the quantity of a specific catalogue sequence numbered part
necessary in the build sequence of only one (where more than one exists), next higher
sub-sub-assembly, sub-assembly, assembly, or installation level as applicable. For bulk
items, the letters "AR" are inserted in the quantity column to indicate "as required". Where
items are listed for reference purposes, "RF" is inserted.
(1) Find the part number in the numerical index. Note down Figure and item number.
(3) Use the item number to find the part in the illustration or in the Parts List.
(1) Refer to Figure 1 and look for the title of the Figure in which the part should be shown.
4. Interchangeability Terms
INTERCHANGEABILITY TERMS
Table 10001
VENDORS LIST
Table 10002
ALPHA/NUMERIC INDEX
DIN98-M6X12-WS-10-A2
(optional, see basic P/N 1052) 021 050 3
023 060 1
EC25001G8B03L02 001B –1 RF
ISO2338-M6-4X40-A4
(optional, see basic P/N 0046) 005 130 4
ISO4762-M5X16-STEEL-8.8-ZN-A2K
(optional, see basic P/N 1140) 008 200 2
ISO4762-M6X20
(optional, see basic P/N 0009) 025 030 4
ISO7045-M5X50-H2-STEEL-4.8-ZN-A2K
(optional, see basic P/N 0367) 023 030 1
ISO7045-M5X6-H2-ST-4.8-ZN-A2K
(optional, see basic P/N 0366) 020 120 2
(optional, see basic P/N 0488) 020 130 5
ISO7045-M6X35-H3-STEEL-4.8-ZN-A2C
(optional, see basic P/N 0360) 021 020 3
ISO7045-M6X50-H3-4.8ZN-A2K
(optional, see basic P/N 0361) 023 020 1
ISO7045M3X8H2-4.8ZN-A2K
(optional, see basic P/N 0237) 024 020 1
ISO7089-A-140-HV
(optional, see basic P/N 0363) 004 205 4
ISO7090-6.4X2.0X1.6-B-140HV-ZN-A2K
(optional, see basic P/N 0016) 004 085 2
021 040 3
023 040 2
ISO8734-A2-M6-4X12
(optional, see basic P/N 1371) 007 050 1
ISO898-1M4.5X12KN6031-H2
(optional, see basic P/N 0335) 006A 030 2
0032
(optional, see basic P/N NAS6605-22) 014 200 1
0069
(optional, see basic P/N 0031) 017 070 2
0200
(optional, see basic P/N 003 040 2
NAS1149G0632P)
0319
(optional, see basic P/N 42NKE054) 014 210 1
0435
(optional, see basic P/N MS21044-N04) 019 472 4
0455
(optional, see basic P/N 014 240 2
NAS1149G0532P)
015A 150 1
0486
(optional, see basic P/N 006A 035 4
NAS1149GN832P)
0705
(optional, see basic P/N 001 580 12
NAS1149G0432P)
001A 580 12
001B 580 12
001C –580 12
004 065 2
235 3
014 250 2
015 090 2
015A 090 2
0763
(optional, see basic P/N MS35335-35) 017 –65 AR
0879
(optional, see basic P/N MS35190-250) 004 120 12
1034
(optional, see basic P/N MS35206-229) 017A 080 1
1240
(optional, see basic P/N MS16995-28) 006A –50 1
018 100 2
1241
(optional, see basic P/N MS16996-9) 011 030 2
1242
(optional, see basic P/N MS16996-10) 014 220 1
1243
(optional, see basic P/N MS16996-11) 001 570 12
001A 570 12
001B 570 12
001C 570 12
1246
(optional, see basic P/N MS16996-23) 007 040 1
1249
(optional, see basic P/N MS51957-41) 004 200 4
1250
(optional, see basic P/N MS51957-42) 005 120 2
006A 040 5
1257
(optional, see basic P/N MS51959-45) 004 110 12
1268
(optional, see basic P/N MS16995-25) 016 070 1
1276
(optional, see basic P/N MS21044-N06) 017A 070 1
1292
(optional, see basic P/N MS16996-21) 016 060 1
018 090 1
1321
(optional, see basic P/N MS18063-19) 005 140 4
1324
(optional, see basic P/N MS16995-9) 003 060 1
1334
(optional, see basic P/N MS51957-14) 019 471 4
1338
(optional, see basic P/N MS21042-3) 015 120 1
015A 120 1
023 050 1
1385
(optional, see basic P/N MS51963-34) 004 130 4
1397
(optional, see basic P/N 015A 160 2
NAS1149G0563P)
1408
(optional, see basic P/N 014B 060 1
5058000007206)
(optional, see basic P/N MS16998-46L) 004 220 3
014A 050 2
050A 6
1430
(optional, see basic P/N 014B 060A 2
5058000007202)
(optional, see basic P/N MS16998-44L) 014B 040 2
(optional, see basic P/N MS16998-47L) 014A 030 1
030A 3
015B 050 1
1452
(optional, see basic P/N MS16998-45L) 015B 040A 2
018 080 4
1453
(optional, see basic P/N MS16998-43L) 013A 150 8
015B 040 4
016 050 4
017 080 4
080A 2
018 070 9
1479
(optional, see basic P/N MS16998-34) 015 110 1
015A 110 1
1563
(optional, see basic P/N MS16998-48L) 004 230 1
017 100 1
1578
(optional, see basic P/N MS18063-12) 008 160 2
1581
(optional, see basic P/N MS18063-11) 005 155 2
008 170 2
1606
(optional, see basic P/N MS16998-44L) 014A 040 1
040A 3
015B 030 4
030A 1
016 080 4
017 090 1
(optional, see basic P/N MS16998-46L) 014B 050 6
1631
(optional, see basic P/N MS21042-08) 006A 045 2
1649
(optional, see basic P/N 019 –520 1
NAS1149DN816J)
1905
(optional, see basic P/N 001 380 1
2232-1-011-8008)
390 1
400 1
001A 380 1
390 1
400 1
001B 380 1
390 1
400 1
001C 380 1
390 1
400 1
1906
(optional, see basic P/N 001 –380A 1
2232-1-021-8008)
–390A 1
–400A 1
001A –380A 1
–390A 1
–400A 1
001B –380A 1
–390A 1
–400A 1
001C –380A 1
–390A 1
–400A 1
INTENTIONALLY BLANK
300
290 120
A
270 490
90
280
110
260 370
80
100 400 210
250 360
50
70
390
350
240
200
380 40
60
230 180
190
700
30
340
220 680
710 170
690
DP029-252072-10000-01-01-00
670
160
20
310
320
130
330
530
540
550
140
150
690
DP029-252072-10000-01-02-00
700
560
580
570
560
640
640
DP029-252072-10000-01-03-00
B
90B
300
370
290 120
A
270 490 B
90
280
110
260 370
80
100 400 210
250 360
50
70
390
350
240
200
380 40
60
230 480
190
450
180
30
340B
220 670
710 170
DP029-252072-10000-01A-01-00
460 440 20
160
470
1B
310B
320B
130
330B
530
540
550
140
150
700
DP029-252072-10000-01A-02-00
560
580
570
560
640
640
DP029-252072-10000-01A-03-00
INTENTIONALLY BLANK
300
290 120
A
270 490
90
280
110
260 370
80
100 400 210
250 360
50
70
390
350
240
200
380 40
60
230 480
190
450
180
30
340
220 670
710 170
DP029-252072-10000-01B-01-00
460 440 20
160
470
310B
320B
130
330B
530
540
550
140
150
DP029-252072-10000-01B-02-00
560
580
570
560
640
640
DP029-252072-10000-01A-03-00
INTENTIONALLY BLANK
300
290 120
A
270 490
280 90
110
370
260
80
100 400 210
360
250
50
70
350 390
240
200
380 40
60
230 480
190
450
180
30
340
220
170
20
DP029-252072-10000-01-01-00
460 440
160
470
310
320
330
DP029-252072-10000-01B-02-00
560
580
570
560
640
640
DP029-252072-10000-01B-03-00
INTENTIONALLY BLANK
80
110
70
50
20
120
30
60
40
DP029-252072-10000-02-01-00
10
INTENTIONALLY BLANK
80
70
110 50
20 120
30
60 40
DP029-252072-10000-02A-01-00
10
50 60
20
40
30 x4
40
70
10
DP029-252072-10000-03-01-00
70 5008290009200 . . WASHER 1
FOR ADJUSTMENT IN FINAL
ASSEMBLY
150
140
220
210
210
235
230
235
235 220
DP029-252072-10000-04-01-00
220
10
190
170
205 x4
200 x4
160
180
20
A
DP029-252072-10000-04-02-00
260
130 x2
100 50
120
130 x2 50
100 120
50
120 30
120
C DP029-252072-10000-04-03-00
40 x2
B
FIG. 4 - IAT ASSY
IAT ASSY (Sheet 3 of 4)
Figure 4
25
62
110
110 x2
110 x2
60
110
110 x2
85 x2
23
80
110
65 x2
REAR BEAM (NP) 120 x4
70
110
DP029-252072-10000-04-04-00
90
120
110 120
INTENTIONALLY BLANK
20 5008281020000 . . IAT-STRUCTURE-ASSY, LH A 1
23 5008281031200 . . . SPACER 3
25 5008281045200 . . . DISTANCE 1
30 5008281048200 . . . SLIDER 1
(TABLEARM)
50 5008281046200 . . . BRACKET 3
4 85 0016 . . . WASHER 2
PN
ISO7090-6.4X2.0X1.6-B-140HV-ZN-A2K
BY VI9008
20
E
DP029-252072-10000-05-01-00
10
140
120 130
120
110
100 130
140
130 95
95 140
130
140
DP029-252072-10000-05-02-00
90
155
90
155
B
95 x2
95 x2
60
95 x4 70
DP029-252072-10000-05-03-00
95 x2
D C
FIG. 5 - TABLE FRONT ROW
TABLE FRONT ROW (Sheet 3 of 4)
Figure 5
30 50
30
40
70
95
95
180
170
80
F
DP029-252072-10000-05-04-00
150
160
INTENTIONALLY BLANK
60 5008462015200 . . CARRIAGE 1
70 0136 . . CARRIAGE 3
FOR LOW PROFILE LINEAR
GUIDE
INTENTIONALLY BLANK
20
40
DP029-252072-10000-06-01-00
10
20A
40C
30
10A
20C
DP029-252072-10000-06-02-00
40C
10C
INTENTIONALLY BLANK
20
40
20
40 40
40
30
30
40
10
DP029-252072-10000-06A-01-00
20A x2
35 x4
45 x2
DP029-252072-10000-06A-02-00
10B
INTENTIONALLY BLANK
INTENTIONALLY BLANK
50
40
20
30
DP029-252072-10000-07-01-00
10
30
10
170 x2
120 100
80
150
130
90
70
110
DP029-252072-10000-08-01-00
160 x2
140
30
200 x2
A
FIG. 8 - BACKREST STRUCTURE ASSY
BACKREST STRUCTURE ASSY (Sheet 1 of 2)
Figure 8
10D
30
DP029-252072-10000-08-02-00
30
A
FIG. 8 - BACKREST STRUCTURE ASSY
BACKREST STRUCTURE ASSY (Sheet 2 of 2)
Figure 8
INTENTIONALLY BLANK
30
20
40 DP029-252072-10000-09-01-00
10
40A
20
20
10A
40
20
10
20
DP029-252072-10000-10-01-00
40 5008001137200 . . TRAMPOLINE A 1
INTENTIONALLY BLANK
30
30
20
30
30
DP029-252072-10000-11-01-00
20
10
20
30
40
10
DP029-252072-10000-12-01-00
60
50
120
40
180
80
100
30
180
160
120
110
180
160
20
130 x2
160 20
140
DP029-252072-10000-13-01-00
10
60
50
100
40
70
80
30 180
170
170
180 90
A 100
170
20
A 110 x2
20
150 x2
120
160
130
DP029-252072-10000-13A-01-00
10
140
A
FIG. 13A - PRIMARY STRUCTURE
Figure 13A
INTENTIONALLY BLANK
70
60
80
30 210
110
230 230
250
40
60
250
240
190
260
70
240
200 50 190
160
220 20
180 x2
170
170
A A 150
140
10
DP029-252072-10000-14-01-00
40 5058000005200 . . BAR 1
60 5008000011200 . . WASHER 2
70 5008000018200 . . WASHER 2
INTENTIONALLY BLANK
20A
50A
20A
20 40A
30A
50
20
40
10A
30
50
10
DP029-252072-10000-14A-01-00
INTENTIONALLY BLANK
20
50
60
20 40
30
50
60A
40
10
30
50
10A
DP029-252072-10000-14B-01-00
130
170
130
120
80
90
100
45
30 50
40
110
100 90 70 60
20A DP029-252072-10000-15-01-00
10D
130
170
130
120
80
90
100
40 70
45
50 110
30
100 90 70 60
20
DP029-252072-10000-15-02-00
10
130
160
170
130
140
120 80
90
100
150
40
45C
50
110
30B
60
70
90
100
20D
DP029-252072-10000-15-03-00
10H
130
160
170
130
140
120 80
90
100
150
40
45A
30C 110
60
70
90
100
20D
DP029-252072-10000-15-04-00
10R
INTENTIONALLY BLANK
60 5008000021200 . . LIMITER 1
100
150
160
70A
130
130
120
125 127
70A
160
150
100
140
40
90
45 70
50
60
110
30
60
70
80 20
DP029-252072-10000-15A-01-00
10
100
150A
160A
70
130 50A
45A
130
40A
120
70
160A
150A
140 100
40A
90
45A 70
50A
60
110
30
60
70
80
20A
DP029-252072-10000-15A-02-00
10B
100
150A
160A
70
130
40B
130
45B
120
70
160A
150A
140 100
45B 90
70
50C
60
110
30
60
70
80
20A DP029-252072-10000-15A-02-00
10F
60 5008000021200 . . LIMITER 2
INTENTIONALLY BLANK
10A 30A
40A
40A
50
20 30 x4
20
40 x4
10
20A
DP029-252072-10000-15B-01-00
30
60
10B 40
INTENTIONALLY BLANK
20
30
80 x4
50 x4
70
DP029-252072-10000-16-01-00
90 40
60
10
90 0363 . . WASHER 1
ØINNER 5,3 ØOUTER 10,0 T 1,0
ISO 7089 / DIN 125 FORM A 140
HV UNTREATED
60x2
50
20
40
70x2
80
10
80
30
60x2
50 80
40
20A
70x2
90 A
100
DP029-252072-10000-17-01-00
30
80A
40A
80A
10A
FIG. 17 - LOK-ATTACHMENT
Figure 17
17 – 1 5058310000012RF LOK-ATTACHMENT NP A RF
SEE FIG. 13 FOR NHA
SEE FIG. 13A FOR NHA
– 1A 5058310000014RF LOK-ATTACHMENT NP B RF
SEE FIG. 13 FOR NHA
– 1B 5058310000015RF LOK-ATTACHMENT NP C RF
SEE FIG. 13 FOR NHA
10 5058310000012 . LOK-ATTACHMENT A 1
20 5058310002202 . . BRACKET A 1
30 5058310002203 . . BRACKET 1
50 5008310002200 . . SUPPORT 1
60 0106 . . BEARING 2
INTENTIONALLY BLANK
55
A
20
60
80 10A
70
40
20
50
10
DP029-252072-10000-17-01-00
80 x2
70
70 70 x4
100
40
30
90
80 x2
60
20
70 x2
50
100
70
10
DP029-252072-10000-18-01-00
B
70 130
A A
60
120
20 30 80 90
10
Electric Plate
40
100
240
DP029-252072-10000-01-01-00
10A
140
DP029-252072-10000-01-01-00
240
INTENTIONALLY BLANK
INTENTIONALLY BLANK
100
80 x3
10
130 x5
60 x4
100
B
110 x2
120 x2
90
50 x4
DP029-252072-10000-20-01-00
40 A
70
30 B
FIG. 20 - SHROUD ASSY
Figure 20
40 5008967038202CG . . . COVER A 1
50 0351 . . . STUD 4
INTENTIONALLY BLANK
50 x3
40 x3
20 x3 30 x6
DP029-252072-10000-21-01-00
FIG. 21 - ATTACHMENT
Figure 21
40 0016 . . WASHER 3
PN
ISO7090-6.4X2.0X1.6-B-140HV-ZN-A2K
BY VI9008
20
20
20
A
DP029-252072-10000-22-01-00
10
50
20
40
30
40
80
60
70
80
70
DP029-252072-10000-23-01-00
10
A
FIG. 23 - ATTACHMENT
Figure 23
40 0016 . . WASHER 2
PN
ISO7090-6.4X2.0X1.6-B-140HV-ZN-A2K
BY VI9008
40
30
20
DP029-252072-10000-24-01-00
10
A
20
20
30 x4
DP029-252072-10000-25-01-00
10
FIG. 25 - ATTACHMENT
Figure 25