Professional Documents
Culture Documents
07 Self Test
07 Self Test
2D730-154E
1.10.1 Outline
The test system is used to identify defective sections of the system. The following sections can
be checked for defects.
(4) PANEL
(5) MAINTENANCE
Test results are displayed as error codes or patterns that provide information for
determining whether each section is defective.
Testing is mainly performed for the CPU, DSC, T&R, and PANEL.
The main systems for imaging can be checked, although not all units are covered. The
identification of defective sections is simplified during troubleshooting, reducing work time.
For maintenance service work, it is possible to detect loss of performance due to defects in
the ultrasound transmission/reception system that are difficult to detect in routine
examinations or abnormalities related to addresses.
The number of cycles of testing can also be specified to allow problems that occur rarely
due to memory errors to be detected.
1-10
No. 2D730-154E
(3) Transient phenomena are displayed during testing. This is not abnormal.
(4) The time, ID area, and hospital name are not cleared. The indication of the contents of the
ID is cleared.
(5) Most switches are disabled during testing. However, operating the image quality
adjustment (IP) switch may cause the system to malfunction.
(6) When the ENTER key is pressed during CPU graphic check, the upper right part of the
image may drop out. This is not abnormal.
Dropout
(7) Either of the two lines for time indication may not be displayed at the end of the CPU
graphic check. This is not abnormal.
1-11
No. 2D730-154E
(1) Prepare the tools and equipment required for the test and gather the relevant manuals.
(5) Display the SERVICE menu (refer to subsection 5.1 "Displaying the SERVICE Menu").
T
ID : 06m23.2004
ABDOM1 14:38:26
* TEST SYSTEM *
* CAUTION *
MAKE SURE THAT PROBE BELOW IS USED :
PROBE --- STANDARD PROBE
(7) When the ENTER key is pressed, the test system menu (various test selection screen) is
displayed.
T
ID : 06m23.2004
ABDOM1 14:39:15
TEST SYSTEM
< MENU >
0 ALL CHECK
1 CPU TEST
X RPG TEST
3 DSC TEST
4 T/R TEST
X FFT TEST
X CFM TEST
7 PANEL TEST
8 MAINTENANCE
9 END
X = CANNOT EXECUTE
1-12
No. 2D730-154E
(8) Enter the number corresponding to the item to be executed and press the ENTER key.
The test is performed.
(9) When the test is completed, error codes and messages are displayed.
(10) Identify the defective PWB by referring to the error code table.
(11) When the test is completed, enter "9" using the keyboard and press the ENTER key to quit
the test menu.
It is also possible to quit the test menu by pressing the NEW PATIENT key or selecting
"TEST" in the menu again.
1-13
No. 2D730-154E
Start
5) V-RAM CPU
R/W
End
6) DSC I/O
DIRECT
1-14
No. 2D730-154E
Sequence Unit to be
Check item Purpose of test (procedure) Result display
No. checked
1 CPU CPU RAM R/W Checks the program RAM OK: "OK" is displayed.
system CHECK of the CPU for
NG: The abnormal
abnormalities.
addresses in RAM are
* The CPU writes data into displayed.
RAM and reads the data,
* Judge: CPU
which is then compared
against the original data.
2 CPU ROM Checks the program ROM OK: "OK" is displayed.
CHECK of the CPU for
NG: The location of the
abnormalities.
abnormal ROM is
* The data in ROM are displayed.
added and then
* Judge: CPU
compared with the data
which were added and
stored in advance.
3 GRAPHIC Checks the OK: White/black patterns
MEMORY character/graphic display are displayed on the
CHECK memory for abnormalities. entire screen.
* The CPU writes "1"s and NG: Dots and/or linear
"0"s into the entire patterns are displayed.
memory sequentially to
* Judge: Service engineer
display white/black
patterns on the entire
screen.
4 RS-232C (ch1) Checks OK: "NORMAL END" is
CHECK transmission/reception of displayed.
data through the RS-232C
* The loop-back NG: Error types are
(option).
CNN is displayed with
required. * Receives transmitted messages.
data as is and compares
* Judge: CPU
it against the original
data.
5 DSC B/W FM Checks B/W FM (frame OK: "OK" is displayed.
CPU R/W memory) 1 and 2 for
NG: The abnormal
abnormalities.
addresses of RAM are
* The CPU writes data into displayed.
FM and reads the data,
* Judge: CPU
which is then compared
against the original data.
6 B/W TEST • Identifies the defective OK: A uniform pattern is
PATTERN section between the DSC displayed.
(SYNC) system and the T&R
NG: A non-uniform pattern
system.
is displayed.
• Checks the sampling * Judge: Service engineer
address.
* Inputs a test pattern
before A/D.
1-15
No. 2D730-154E
Sequence Unit to be
Check item Purpose of test (procedure) Result display
No. checked
7 DSC B/W TEST • Identifies the defective OK: A uniform pattern is
PATTERN section between the DSC displayed.
(ASYNC) system and the T&R
NG: A non-uniform pattern
system.
is displayed.
• Checks the transmission * Judge: Service engineer
multi-steps.
8 B/W LIP TEST Checks whether the OK: An interpolated vertical
PATTERN defective section is in a line pattern is
section after (and including) displayed.
or before the output system
NG: A pattern that is not
of the DSC system.
interpolated normally
* Writes a test pattern in is displayed.
frame memory.
* Judge: Service engineer
9 V-RAM Checks VECTOR RAM for OK: "OK" is displayed.
CPU R/W abnormalities.
NG: The abnormal
* The CPU writes data into addresses of RAM are
RAM and reads the data, displayed.
which is then compared
* Judge: CPU
against the original data.
10 DSC I/O Discriminates the DSC FM OK: A uniform pattern is
DIRECT PWB from other sections. displayed.
* Performs D/A of signals NG: A non-uniform pattern
that have undergone A/D is displayed.
by bypassing FM to
* Judge: Service engineer
display a test pattern,
which is checked for
abnormalities.
11 T&R T&R TEST1 Identifies the defective OK: A pattern without echo
system section in the T&R system. dropouts is displayed.
NG: A pattern with echo
dropouts is displayed.
* Judge: Service engineer
12 PANEL Checks the panel for OK: All panel lamps light.
abnormalities.
NG: Some panel lamps do
not light.
* Judge: Service engineer
1-16
No. 2D730-154E
(2) Enter the number of times testing should be performed and press the
ENTER key. The entered value is displayed in the CHECK COUNT
field of the original menu.
Terminate testing if the Press the DEL key.
number of times testing
is performed is infinite.
Correct incorrect entries Press the DEL key and then enter the correct numeric value.
during data entry.
1-17
No. 2D730-154E
1-18
No. 2D730-154E
(1) Preparation
The flow of the CPU test is shown below. When operating the test system, refer to this
flowchart to identify the point where you are located.
<CPU TEST>
START
Selection of
the test mode
3:GRAPHIC
MEMORY 4:RS-232C (CH-1) 7:CHECK
0:ALL CHECK 1:RAM CHECK 2:ROM CHECK CHECK CHECK COUNT SET 8:END
Check of
Check of the character/graphics Operational Specification of the Quits the CPU test
R/W check R/W check ROM display memory check of number of times and returns to the
of RAM of RAM (Plane 1: for testing should be
checksum RS-232C IF 1H performed main menu.
character display)
Check of
Check of the RETURN RETURN character/graphics RETURN RETURN
ROM display memory
(Plane 2: for mark
checksum display)
Check of
Check of character/ character/graphics
graphics display display memory
(Plane 3: for
memory measurement mark)
Check of
RETURN character/graphics
display memory
(Plane 4: for
auto-data display)
Check of
character/graphics
display memory
(Plane 5: for menu
data display)
Check of
character/graphics
display memory
(Plane 6: for menu
area)
RETURN
1-19
No. 2D730-154E
When "1 CPU TEST" is selected in the test system menu, the following screen is displayed.
Enter the number corresponding to the item to be executed and press the ENTER key.
The test is performed.
T
ID : 06m23.2004
ABDOM1 13:12:35
CPU TEST
( MENU ) CHECK COUNT = 001
0 ALL CHECK
1 RAM CHECK
2 ROM CHECK
3 GRAPHIC MEMORY CHECK
4 -
RS 232C -
( CH 1 ) CHECK
X -
RS 232C -
( CH 2 ) CHECK
X CENTRONICS CHECK
7 CHECK COUNT SET
8 END
X = CANNOT EXECUTE
1-20
No. 2D730-154E
(a) When the test is completed, the result is displayed for each RAM sequentially.
T
ID : 06m23.2004
ABDOM1 13:13:17
CPU RAM CHECK
*** ***
*
SRAM1 SRAM2 OK
SRAM3 SRAM4 OK
END
NEXT CHECK -- > PRESS [ENTER] PREVIOUS MENU -- > PRESS [BS]
When the ENTER key is pressed, the screen changes to the next check (CPU ROM
CHECK).
When the BS key is pressed, the screen returns to the CPU test menu.
(c) If the test result indicates an abnormality, the abnormal address and results of
comparison are displayed.
Enter "C" to quit the RAM check currently being executed and check the next RAM.
When all RAM checks are completed, the screen shown above is displayed.
Operation at the time of completion for all addresses is the same as for (b) above.
1-21
No. 2D730-154E
(a) When the test is completed, the result is displayed for each ROM sequentially.
T
ID : 06m23.2004
ABDOM1 14:42:20
CPU ROM CHECK
*** ***
* ( X08 )
IC4F 2860 OK
IC4H ( X10 ) 6B00 OK
IC4K ( X18 ) 697D OK
IC3F ( X40 ) B8E5 OK
IC3H ( X48 ) 44B2 OK
IC3K ( X50 ) 006F OK
IC3M ( X58 ) 48C4 OK
END
NEXT CHECK -- > PRESS [ENTER] PREVIOUS MENU -- > PRESS [BS]
When the ENTER key is pressed, the screen proceeds to the next check (GRAPHIC
MEMORY CHECK).
When the BS key is pressed, the screen returns to the CPU test menu.
(c) If the test result indicates an abnormality, the location of the abnormal ROM is
displayed.
T
ID : 06m23.2004
ABDOM1 13:15:38
NEXT CHECK -- > PRESS [ENTER] PREVIOUS MENU -- > PRESS [BS]
Operation when all ROM checks are completed is the same as for (b) above.
1-22
No. 2D730-154E
(a) When the test is selected, the following screen is displayed. The test starts when the
ENTER key is pressed.
T
ID : 06m23.2004
ABDOM1 13:16:24
GRAPHIC MEMORY CHECK
*** ***
CAUTION
* *
CHECK SEQUENCE ( EXECUTE -- > PRESS [ F ] )
1 = GRAPHIC MEMORY 1 ALL 1
2 = GRAPHIC MEMORY 1 ALL 0
3 = GRAPHIC MEMORY 2 ALL 1
4 = GRAPHIC MEMORY 2 ALL 0
(b) When operation is normal, the screen appears white. When the "F" key is pressed,
the screen appears black.
When the "F" key is pressed again, the screen proceeds to the next graphic memory
check.
When the ENTER key is pressed, the screen proceeds to the next check (RS-232C
(CH1)).
When the BS key is pressed, the screen returns to the CPU test menu.
1-23
No. 2D730-154E
(c) If the test result indicates an abnormality, the screen does not appear "white" or
"black".
Operation when all graphic memory checks are completed is the same as for (b)
above.
1-24
No. 2D730-154E
(a) When the test result is normal, the following screen is displayed.
T
ID : 06m23.2004
ABDOM1 13:19:19
*** -
RS 232C ( CH1 ) CHECK
***
-
IF RS 232C I/F IS NOT CONNECTED.
THE TEST WILL BE FINISHED AFTER ABOUT 60 SECONDS.
NORMAL END
NEXT CHECK -- > PRESS [ENTER] PREVIOUS MENU -- > PRESS [BS]
When the ENTER key is pressed, the screen proceeds to the next check.
When the BS key is pressed, the screen returns to the CPU test menu.
(b) If the test result indicates an error, the following error messages are displayed.
Operation after an error message is displayed is the same as for (a) above.
1-25
No. 2D730-154E
A correct checksum value must have been registered in order to perform the CPU ROM
check (registered at the time of shipment from the factory). The following three registration
methods are available.
When setting is performed using the DIP switch, the preset data is also initialized.
Record the preset data before operating the DIP switch and restore the data after
DIP switch setting is completed.
<1> Set bit 3 of the DIP switch on the CPU PWB to ON.
<3> When the message "INITIALIZE PRESET DATA ARE YOU SURE?" is
displayed, press the "Y" key.
<4> After the initial screen for B-mode images is displayed, set bit 3 of the DIP
switch to OFF.
When setting is performed using SYSTEM setup, the preset data is also initialized.
Record the preset data before SYSTEM setup and restore the data after SYSTEM
setup is completed.
<4> When the confirmation message is displayed, press the "Y" key.
1-26
No. 2D730-154E
(1) Preparation
None
The flow of the DSC test is shown below. When operating the test system, refer to this
flowchart to identify the point where you are located.
<DSC TEST>
START
Selection of
test mode
0:ALL CHECK 1:B/W FM 2:B/W TEST 4:B/W 10:VECTOR RAM 11:DSC I/O 13:END
CPU R/W PATTERN LIP TEST CPU R/W DIRECT
(SYNC) PATTERN
R/W check of
V-RAM
Check of the
DSC-I/O
DIRECT
RETURN
1-27
No. 2D730-154E
When "2 DSC TEST" is selected in the test system menu, the following screen is displayed.
Enter the number corresponding to the item to be executed and press the ENTER key.
The test is performed.
T
ID : 06m23.2004
ABDOM1 13:20:04
DSC TEST
< MENU > CHECK COUNT = 001
X = CANNOT EXECUTE
1-28
No. 2D730-154E
(a) When the test is completed, the result is displayed for each RAM sequentially (in the
order FM1, FM2).
T
ID : 06m23.2004
ABDOM1 13:21:00
B/W FM1 RAM CHECK
*****
OK *****
END
B/W FM2 RAM CHECK
*****
OK *****
END
NEXT CHECK -- > PRESS [ENTER] PREVIOUS MENU -- > PRESS [BS]
When the ENTER key is pressed, the screen proceeds to the next check (B/W TEST
PATTERN (SYNC)).
When the BS key is pressed, the screen returns to the DSC test menu.
(c) If the test result indicates an abnormality, the abnormal address and the results of
comparison are displayed.
Enter "C" to quit the RAM check currently being executed and check the next RAM.
When all RAM checks are completed, the screen shown above is displayed.
Operation at the time of completion of all addresses is the same as for (b) above.
1-29
No. 2D730-154E
(a) When the test result is normal, the following screen is displayed.
When the ENTER key is pressed, the screen proceeds to the next check (B/W TEST
PATTERN (ASYNC)).
When the BS key is pressed, the screen returns to the DSC test menu.
(c) If nothing is displayed as a test result, the DSC-FM and DSC-IO are defective. If
abnormal images are displayed, execute the B/W TEST PATTERN (ASYNC) test. If
abnormal images are also displayed in this test, the DSC-FM and DSC-IO are
defective.
* When both this test and the B/W TEST PATTERN (ASYNC) test are executed
normally, there are no abnormalities in the DSC system. Signals from the
RECEIVER are not transmitted.
1-30
No. 2D730-154E
When the ENTER key is pressed, the screen proceeds to the next check (B/W LIP
TEST PATTERN).
When the BS key is pressed, the screen returns to the DSC test menu.
(b) If there are any abnormalities in the transmission multi-stages as a result of the test,
the image is not separated into the number of stages specified. The RPG and DSC-
I/O are defective.
* When both this test and the B/W TEST PATTERN (SYNC) test are executed
normally, there are no abnormalities in the DSC system. Signals from the
RECEIVER are not transmitted.
1-31
No. 2D730-154E
(a) When the test result is normal, the following screen is displayed. This screen
indicates that the systems subsequent to (and including) the frame memory are
normal.
When the ENTER key is pressed, the screen proceeds to the next check (VECTOR
RAM CPU R/W).
When the BS key is pressed, the screen returns to the DSC test menu.
(b) If the test result indicates that interpolation is not performed normally, there is an
abnormality in the LIP. If no patterns are displayed or gradations are abnormal, there
is a defect in the system from frame memory output (including the LIP) to the D/A
converter.
* When this test is normal and no patterns are displayed in the B/W TEST
PATTERN (SYNC) test and B/W TEST PATTERN (ASYNC) test, there is an
abnormality in the system from the AD input to the frame memory.
1-32
No. 2D730-154E
(a) When the test is completed, the result is displayed for each RAM sequentially.
T
ID : 06m23.2004
ABDOM1 13:23:23
VECTOR RAM R/W CHECK
*****
VE - RAM1 VE - RAM2 OK *****
END
NEXT CHECK -- > PRESS [ENTER] PREVIOUS MENU -- > PRESS [BS]
When the ENTER key is pressed, the screen changes to the next check (DSC I/O
DIRECT).
When the BS key is pressed, the screen returns to the DSC test menu.
(c) If the test result indicates an abnormality, the abnormal address and the results of
comparison are displayed.
Enter "C" to quit the RAM check currently being executed and check the next RAM.
When all RAM checks are completed, the screen shown above is displayed.
Operation at the time of completion for all addresses is the same as for (b) above.
1-33
No. 2D730-154E
(a) When the test result is normal, the following screen is displayed. This screen
indicates that the DSC I/O is normal.
When the BS key is pressed, the screen returns to the DSC test menu.
(b) If the test result indicates an abnormal pattern, the DSC I/O is defective.
* When this test is normal and there is an abnormality in the B/W TEST PATTERN
(SYNC) test and B/W TEST PATTERN (ASYNC) test, the DSC FM is defective.
1-34
No. 2D730-154E
(1) Preparation
None
(c) When the test is completed, the following test pattern is displayed. This pattern
indicates initial echoes transmitted/received for each raster one channel at a time.
The test result is normal when there are no dropouts in the test pattern.
ch90 ch1
When the ENTER key is pressed, the screen proceeds to the next check (PANEL
TEST).
When the BS key is pressed, the screen returns to the T&R test menu.
(d) If there are dropouts in the echo as a result of the test, analysis is performed
according to the pattern of dropouts. If the T&R is determined to be defective as a
result of the test, replace the DIGITAL PWB.
1-35
No. 2D730-154E
(1) Preparation
None
(b) The PANEL is normal when all panel lamps light and go out.
If some lamps do not light, they are defective. If the PANEL is found to be defective
as a result of the test, replace the PANEL.
1.10.12 MAINTENANCE
This menu is not directly related to testing, but is provided to assist in testing. When "8
MAINTENANCE" is selected in the test system menu, the following screen is displayed. Enter
the number corresponding to the item to be executed and press the ENTER key. The test is
performed.
T
ID : 06m23.2004
ABDOM1 13:26:21
MAINTENANCE
< MENU >
1 CHECK SUM
2 PWB INFORMATION
3 SYSTEM SETUP
4 END
1-36
No. 2D730-154E
(a) When this item is selected, the checksum is registered automatically. It takes
approximately 1 minute to complete this test.
(b) When registration is completed, the screen returns to the main menu.
1-37
No. 2D730-154E
T
ID : 01m30.2004
ABDOM1 10:33:57
MAINTENANCE
< PWB INFORMATION
> DIGITAL : 0 2
RECIVER : - 1
PULSER : - 1
The revisions of DIGITAL, RECEIVER, and PULSER are displayed. The revisions may
be higher than those displayed depending on changes to the hardware and software.
The connection statuses of IMAGE MEMORY (IM), RS-232C, I/O PANEL, and T/R are
displayed. Items that are connected are displayed as "CONNECTED" and those that
are not connected are displayed as "NOT CONNECTED".
• Check of the RTC battery for remaining capacity (for the DIGITAL PWB)
Checks the remaining capacity of the battery for displaying the timer and calendar.
When the remaining capacity is satisfactory, OK is displayed. Otherwise "NG" is
displayed, in which case the DIGITAL PWB must be replaced.
(b) When the BS key is pressed, the screen returns to the MAINTENANCE menu.
1-38
No. 2D730-154E
T
ID : 06m23.2004
ABDOM1 13:27:52
MAINTENANCE
< SYSTEM SETUP >
DIP SW 3 : OFF
DIP SW 5 : OFF
DIP SW 6 : OFF
(b) Enter the number of the item to be initialized and press the ENTER key. The item
changes from "OFF" to "ON".
(c) When the power is turned OFF and ON again in this status, a screen for confirming
whether initialization should be performed is displayed.
* The system displays the confirmation message above when the power is next turned
ON only if the power was turned OFF after item initialization. The system operates
normally for subsequent power ON/OFF cycles.
1-39