Professional Documents
Culture Documents
Fosroc Renderoc Laxtra: Constructive Solutions
Fosroc Renderoc Laxtra: Constructive Solutions
Fosroc Renderoc Laxtra: Constructive Solutions
Uses Properties
Renderoc LAXtra is suitable for mass infill to structural The following typical results were obtained at a water:powder
repairs in all types of load bearing situation. Typical applica- ratio of 0.135
tions would include, but not be limited to, the following :
Test method Typical result
Repairs to columns suffering from major loss of section
Drying shrinkage to ASTM C157-93
Soffit repairs where heavy load bearing is required
7 days : < 0.03%
Repairs to restricted access areas, where use of hand 28 days : < 0.04%
applied mortars would prove impractical Permeability : < 10 mm
(DIN 1048 Part 5)
Repairs requiring high fluidity e.g. heavily congested steel
Flexural strength : > 9 N/mm2 at 28 days
or repairs into re-entrant angles/concealed voids
(BS 6319 Pt.3)
Any repairs requiring significant levels of loadbearing Tensile strength : > 5 N/mm2 at 28 days
(BS 6319 Pt.7)
Advantages Compressive strength : > 39 N/mm2 at 3 days
(BS 1881 Pt.116 ) > 50 N/mm2 at 7 days
1
Renderoc LAXtra features Dimensional Stability Technol-
> 60 N/mm2 at 28 days
ogy - a new materials technology which controls the rate of
Water absorption : < 2%
drying shrinkage such that, when used correctly :
(BS 1881 Pt. 122)
i. the dimensions of the repair remain stable; and thus Note1: 100mm cubes, air cured @ 200C
ii. eliminating failure, due to shrinkage cracking.
Design criteria
This in turn leads to a series of associated benefits :
Dimensional Stability Technology is a major step forward
Cost effective - shrinkage control enables repairs to be in the general compatibility of repair mortar systems with the
completed ‘right first time’ host concrete, and the control of shrinkage in particular.
Enhanced durability - works in tandem with extremely Attention to the basic design criteria given below should
low permeability to prolong effective working life ensure that the full benefits of this technology are gained in
Compatibility - aligns performance closer than ever use :
before, to that of host concrete (i) Renderoc LAXtra is designed for large volume repairs,
User friendly - specifically developed to provide an easy- typically in excess of 50 mm deep. The product can be
to-apply product, suitable for local conditions applied in sections generally between 50 and 200 mm
thick, greater thicknesses may be achievable, depending
Definable performance - positive benefits are easily upon repair configuration and location together with the
demonstrated via a single, simple measurement volume of reinforcing steel.
Consult the local Fosroc office for more information.
Description
(ii) In situations where a substrate/repair barrier is required,
Renderoc LAXtra is supplied as a ready to use blend of dry or enhanced bond strength/working time is required, or
powders and selected aggregates, which requires only the where the substrate is likely to be damp (e.g. seawalls,
addition of clean water to produce a highly consistent, fluid quays etc.), Nitobond EP epoxy bonding agent should be
microconcrete suitable for all load-bearing situations. used.
Renderoc LAXtra should be mixed and applied in strict Health and safety
accordance with the Product Method Statement, a copy of
Renderoc LAXtra contains cement powders which, when
which may be obtained from your nearest Fosroc office.
mixed with water or upon becoming damp, release alkalis
which can be harmful to the skin.
Estimating
During use, avoid inhalation of the dust and contact with
Supply
the skin or eyes. Wear suitable protective clothing - eye
Renderoc LAXtra : 25kg bags protection, gloves and respiratory equipment (particularly in
confined spaces).
Yield
The use of barrier creams to provide additional skin protec-
Renderoc LAXtra : 12.25 ltrs per 25kg bag
tion is also advised. In case of contact with the skin, rinse
with plenty of clean water, then cleanse thoroughly with soap
Limitations
and water.
- Renderoc LAXtra should not be used when the ambient
In case of contact with eyes, rinse immediately with plenty
temperature is below 5°C and falling.
of clean water and seek medical advice. If swallowed seek
- Renderoc LAXtra should not be part mixed, nor part bags medical attention immediately - do not induce vomiting.
used.
Fire
- Renderoc LAXtra should not be exposed to running water
Renderoc LAXtra, is non-flammable and thus presents no
either during application or prior to final set.
fire hazard.
- Water ponding is not recommended for curing.
For further information, please refer to the Product Material
Safety Data Sheet for Renderoc LAXtra.
Storage
Shelf life
Standards compliance
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of
Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to obtain the latest version.
Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: agf@fosroc.com
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: bahrain@fosroc.com
United Arab Emirates Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com
Oman, Al Amana telephone: 24815080 fax: 24817554 email: oman@fosroc.com
www.fosroc.com Qatar, Tadmur telephone: 4432365 fax: 4419517 email: qatar@fosroc.com
UAE/0253/13/J