REB ITEM: L-6 Through t-14
PUBLICATION 421-2017
BANGLADESH RURAL ELECTRIFICATION BOARD (BREB)
PEOPLES REPUBLIC OF BANGLADESH
STANDARD FOR
LED STREET LIGHTING EQUIPMENT
SCOPE
This standard establishes the physical and performance requirements for LED street lighting
equipment to be used on BREB overhead distribution lines.
2. GENERAL
Street lighting equipment furnished to BREB specification shall conform in all respects to the
physical and performance requirements of this standard. The text, figures, and reference to
other standards supplement each other and are considered part of this standard.
3. REFERENCE DATA
BREB luminaire package (BREB Ttem L-6) shall consist of a die-cast aluminum head within a
maximum 80 Watts SMD LED consist of driver, heat radiator, Aluminum housing, 1%" pipe
bracket mounting, mogul multiple heavy duty porcelain socket, one reflector and refractor
assembly consisting of @ drawn aluminum reflector with stainless steel latches, refractor
assembly of one piece, type five design, acrylic plastic (Shown in the indicative drawing)
Which is capable to illuminate minimum 8000 lumen with power factor minimum 0.95,
Nominal Input of the light will be single phase, two wire, 230V, SOHZ and should be able to
‘operate from 165V to 250V without any deviation in brightness. The Light assembly must be of
P65 rating and all exposed materials should be weather and rust proof. One single pole
switch(MCB) as required, one 1%" diameter by 30° long aluminum pipe bracket, Bracket
shall be mounted with bolts and 2 lag screws and one package of wooden/galvanized
steel/SPC pole mounting hardware, All fittings and fixture accessories should be provided.
BREB Item L-7 shall be 2 one piece, type five, acrylic plastic replacement refractor for
luminaire described above in BREB Item L-6,
BREB Item L-8 maximum 80-Watts, 230 Volt, LED lamp to be used for replacement
Luminaire for BREB Item L-6.
GE
l
Publication 421-2017; Revision: 1; Date: Sep, 2020 \<\ #1) Page 1 of 3
aEREB ITEM: L-6 Through L-11
BREB Items L-9, L-10 & L-11 shall be 240(+20%)V, 60A, 30A & 15A respectively single pole
switch(MCB) to be used for replacement of MCB in BREB Item L-6. These MCB as accessories
will be from USA, Europe or Japan origin. BREB street lighting equipment shall meet the
requirements of ANSI C136.6-1984, ANSI C136.10-1979, ANSI C78.377-2008 and ANSI
C136.13-1979. Catalog of the LED should be provided along with the bid document.
4, INSPECTION
‘The Manufacturer shall perform the necessary inspection and tests to determine if the street
lighting equipment complies with the specification and the related standard. Non-conforming
of any parameter of street lighting equipment is unacceptable. BREB reserves the right to
witness factory tests and shall request test reports. During Pre shipment the BREB
inspection team will perform all the routine tests at manufacturer premises (at least two
members nominated by BREB), Possible all the routine tests should be perform during post
fanding inspection,
5. WARRENTY
(One (1) year from date of received.
6. OTHER STANDARDS.
‘The physical and performance requirements of street lighting equipment based on other
international recognized standards, is acceptable only if the requirements of such standards
are equivalent to or exceed the requirements quoted in this document.
7. BIBLIOGRAPHY OF REFERENCE STANDARDS:
1, ANSI C136.6-1984: Reflector Assemblies and Metal Head Interchangeabilty.
2. ANSI C136.10-1979: Interchangeability of Photo Control Device Plug and Mating
Receptacle Used in Roadway Lighting Equipment.
3. ANSI C136.12-1979; Metal Brackets.
4, ANSI C78.377-2008 Specifications for the Chromaticity of Solid State Lighting Products
5. ANSI C79,1~ 2002 American National Standard for Electric Lamps ~ Nomenclature for
Glass Bulbs Intended for Use with Electric Lamps
6. ANSI C78.20 - 2003 American National Standard for Electric Lamps ~ A, G, PS, and
Sitvilar Shapes with £26 Medium Screw Benes,
TE
Publication 421-2047; Revision: 4; Date: Sep, 2020 i Page 20° 37. ANSI C78.21 ~ 2003 American National Standard for Electric Lamps ~ PAR and RShapes
8, ANSI C78.24 ~ 2001 American National Standard for Electric Lamps ~ Two-inch (51 mm)
Integral-reflector Lamps with Front Covers and GUS.3 or GX 5.3 Bases
9. ANSI/IEC C81.61-2003 American National Standard for Electric Lamp Bases.
eens, TARA, VR
Publication 421-2017; Revision: 1; Date: Sep, 2020 Page 3 of 3REB ITEM :L-6
Die-Cast Aluminium
Luminaire Head
Acrylic Plastic Refractor
A» Indicative Drawing-1
SD
"Dy
aZ-3UIMeIG aANeoTpUT