Professional Documents
Culture Documents
ID961 Instruction Manual
ID961 Instruction Manual
ID961 Instruction Manual
USER INTERFACE set the desired value using the “UP” and
If you do not use the keyboard for over “DOWN” keys, and confirm with the “set”
The user has a display and four keys for 15 seconds (time-out) or if you press the key to move to the next parameter.
controlling status and programming of the “fnc” key once, the last value shown on PLEASE NOTE: It is suggested to switch-
instrument. the display is confirmed and you return to off and switch-on again the instrument
the previous screen mask. everytime it is changed the configuration
KEYS AND MENUS of the parameters: this prevents malfunc-
MACHINE STATUS MENU tioning on regulation and delay time
UP key Scrolls through the menu items (See Machine Status Menu)
Increases the values
occuring.
Activates manual defrost
To access the “Machine Status” menu
Press and quickly release the “set” key. PASSWORD
DOWN key Scrolls through the menu items If alarms are not present, the label “SEt” The password “PA1” allows access to pro-
Decreases the values
appears. By using the “UP” and “DOWN” gramming parameters. In the standard
Programmable by parameter
keys you can scroll through the other fold- configuration password is not present.
fnc key
fnc ESC function (exit) ers in the menu: To enable (value≠0) and assign it the
Programmable by parameter -Pb1: probe 1 value folder; desired value, access the “Programming”
set key Accesses the setpoint -SEt: Setpoint setting folder. menu, within the folder with the “diS”
set Accesses the menus Set Setting label. If password is enabled, you will see
Confirms the commands Access the “Machine Status” menu by it at the entrance of the “Programming”
Displaying the alarms (if present)
pressing and quickly releasing the “set” menu (see the “Programming Menu“ sec-
key. The label of the “Set” folder appears. tion).
To display the Setpoint value press the
“set” key again. MANUAL ACTIVATION OF THE
f nc The value appears on the display. DEFROSTING CYCLE
To change the Setpoint value, use the “UP” To manually activate the defrosting cycle,
set and “DOWN” keys within 15 seconds. press the “UP” key for 5 seconds.
If the parameter is LOC = y the Setpoint
ID961 cannot be changed. COPY CARD
Displaying Probes The Copy Card is an accessory connected
By pressing the “set” key when the appro- to the TTL serial port which allows pro-
At start-up the instrument performs a priate label appears, the value of the gramming quickly the instrument parame-
Lamp Test; for few seconds the display and probe associated to it is displayed. ters. The operation is performed as fol-
the leds blink, in order to verify their lows:
integrity and correct operation. The instru- PROGRAMMING MENU Format
ment has two main menus: the “Machine (See Programming Menu) This command allows copy card format-
Status” and “Programming” menu. To enter the “Programming” menu, press ting, an operation recommended in case
the “set” key for more than 5 seconds. of first use.
ACCESSING AND USING MENUS If specified, the access PASSWORD will be Warning: if the copy card has been pro-
Resources are arranged in a menu, which requested, (parameter “PA1”), and (if the grammed, using the “Fr” the data entered
can be accessed by pressing and quickly password is correct) the label of the first are erased. This operation cannot be can-
releasing the “set” key (“Machine Status” folder will follow. celled.
menu) or by holding down the “set” key To scroll through the other folders, use Upload
for more than 5 seconds (“Programming” the “UP” and “DOWN” keys. This operation loads the programming
menu). If the password is wrong, the display will parameters from the instrument.
To access the contents of each folder, indi- show the PA1 label again. Download
cated by the relevant label, just press the To enter the folder, press “set”. The label This operation downloads to the instru-
“set” key once. of the first visible parameter appears. To ment the programming parameters.
You can now scroll through the contents scroll through the other parameters, use The operations are performed accessing
of each folder, modify it or use its func- the “UP” and “DOWN” keys; to change the the folder identified by the “FPr” label and
tions. parameter, press and release “set”, then selecting, according to the case, “UL”, “dL”
or “Fr” commands; the operation is con-
LED firmed by pressing the “set” key. If the
operation is successful an “y” is displayed,
Position Related Function Status on the contrary, if it fails a “n” will be dis-
Compressor or relay 1 ON when the compressor is started up; blinking in case of delay, played.
protection or blocked enabling
NOTE:
Defrost ON when defrosting; blinking in case of manual • UPLOAD: instrument --> Copy Card
enabling • DOWNLOAD: Copy Card --> instru-
ment.
Alarm ON when the alarm is enabled; blinking when the alarm is silenced
ID 961 2/5
Tab. 1 Parameter Table
ddL defrost display Lock. Viewing mode during defrosting. 0/1/2 1 1 flag
0 = shows the temperature read by the thermostat probe;
1 = locks the reading on the temperature value read by thermostat probe when
defrosting starts, and until the next time the Setpoint value is reached;
2 = displays the label “deF” during defrosting, and until the next time the
Setpoint value is reached.
dro display read-out. Select °C or °F for displaying the temperature read by the thermostat 0/1 0 1 flag
probe. 0 = °C, 1 = °F.
CONFIGURATION (folder with “CnF” label)
H00 (*) Probe type selection, PTC or NTC. 0 = PTC; 1 = NTC. 0/1 0/1 1 flag
reL reLease firmware. Device version: read only parameter. / / 1 /
tAb tAble of parameters. Reserved: read only parameter. / / 1 /
COPY CARD (folder with “Fpr”label)
UL Up load. Programming parameter transfer from instrument to Copy Card. / / 1 /
dL Down load. Programming parameter transfer from Copy Card to instrument / / 1 /
Fr Format. Erasing all data in the copy card. / / 1 /
PLEASE NOTE: using “Fr” parameter (copy card formatting) the data within the
copy card will be lost permenently. The operation cannot be cancelled.
** VALUE column: to be filled manually, with customized settings (if different from the default value).
*** LEVEL column: indicates the level of visibility of parameters accessible by PASSWORD (see the related paragraph)
ID 961 3/5
press and release set SEt set SEt value
(single press)
change
SEt value
scroll
parameters
PARAMETERS
folders level 1
CP
dEF
diS
Fpr set level 1 par
CnF
FPr
ID 961 - 230 V A
1 2 3 6 7 8 9
TERMINALS
ID 961 - 230 V A
4-5 N.O. compressor relay output
6-7 Power supply 16A 2hp
8 - 10 Probe 1 input (thermostat)
A TTL input for Copy Card
4 5 6 7 8 9 10