Professional Documents
Culture Documents
AXOR Katalog - Tech - en - 12 - 09 - 2019 PDF
AXOR Katalog - Tech - en - 12 - 09 - 2019 PDF
1 Hinges
2 Gears
4 Stay arm
5 Additional elements
7 Installation Tools
8 Profile-depending elements
rev. 2.03.05
12.09.2019
System KOMFORT LINE K-3 General product
information
Application range All window furniture in our catalogue is intended exclusively for the internal
opening of windows and balcony doors.
The system K3 has been provided in such assemblies as, tilt and turn opening,
single turn opening, single tilt opening and double sash opening as well.
Hardware elements All sets of hardware, which were indicated in this catalogue, must consist only
from original elements of AXOR INDUSTRY. Otherwise the producer won’t be able
to guarantee the work of hardware properly.
So, for each type of a sash, it is possible to set optional elements for additional
functionality of one. These elements were marked with following colors:
Red – base safety;
Grey – possible equipment.
Assembly So, for accurate an assembly and for further correct work of hardware it is
necessary to follow instructions of this catalogue.
Fixing of details:
The handle with screws M5 x 40mm.
The elements of a sash and the locking plates: self-tapping window chromated
screws 4,0 x 25 mm or 3,9 x 26 mm.
The elements of hinges group: galvanized or alternatively chromated screws with
flat head and cross-shaped slot, DIN 7982 3,9 x 32 mm or 3,9 x 38 mm.
Preliminary drilling is necessarily for these screws. Perforation instead of drilling is
forbidden. Drill diameter for PVC profiles is 0.7, and for steel profiles is 0,8 diameter
of a screw.
Settings of electric- or pneumatic screwdriver: maximum torque is 2.5 Nm, rotation
speed: max 600 - 1000 rpm.
In case of non-compliance of these catalogue’s recommendations for assembly and exploitation, the producer AXOR INDUSTRY cannot
guarantee properly work of separate elements, as well as, the work of hardware system in whole.
The AXOR INDUSTRY Company reserves the right, in a process of further an improvement and development, to make technical changes of
product KOMFORT LINE K-3, and also to change packaging norms.
2
Locking pins General product
information
The system of window hardware KOMFORT LINE K-3 was equipped with cylindrical pins of sliding.
Thus, as additional option it is possible to complement elements of a sash with a mushroom pin, to conform the base safety level according
to AhS Standard.
In order to ensure air and water permeability of window and balcony door units in accordance with the GOST 23166 and DSTU Б В.2.6-39:2008
standards, the construction of turn, tilt and tilt&turn devices shall ensure that the contact between the sash (leaf) and the frame remains tight
and even for the entire duration of service life, based on recommendations from the profile system manufacturers, the use of a certain type
of gasket and observance of the required size of gap under the gasket (GOST 30777-2012), which means that when assembling a tilt-and-turn
(turn) window, the manufacturer must receive recommendations regarding the number of and the distance between the locking points directly
from the profile manufacturer, in writing and with the explanation of these requirements.
The adjustment range of locking pins is +/-1 mm. The diameter of pins is 11 mm.
1) All elements of hardware have holders which allow fixing ones 8) The wrong operation safety device with sash lifter is universal
in the fitting groove before screwing by screws and to prevent for left and right opening. There is a fixation of the central position
moving along of fitting groove during assembly of a sash. before a moment of assembly. It can work even the gap between
the frame rebate and sash rebate is from 10,5 till 14 mm. Thus, if
2) There is an opportunity to fix the finger of the corner bearing at it is necessary there is an opportunity to adjust a lifting plate at
the extreme bottom position under angle 180° in order to make an +/- 1 mm by height. So, the setting of the lifting pate with a special
assembly more comfortable by a screw gun, so the finger is not telescopic jig provides the correct work this wrong operation
falling down and hindering to screw the screws. safety device whole.
3) The holes of the corner bearing and stay arm bearing were 9) The bottom extension has “a ski-lift” which was integrated to
designed thus all screws to pass through reinforcement profile this one, thus it excludes the sagging down of a sash when it is
inside of a frame. closed.
4) The drill-in corner hinge has two pins following sizes: length 5 10) The junction of the middle lock to the stay arm is quite reliably
mm and diameter 3 mm to fix reliably this one before the moment thanks to a screw, which joins these ones.
of screwing by screws.
11) The adjustment range of the stay arm by a gasket pressing is
5) There is a plastic bush, of high-strength polymer, Inside of the +/- 1 mm.
drill-in corner hinge, which prevents unscrewing of an adjustable
screw during the turning of a sash. Thus there is not any creak 12) There are four types of middle locks thus, it is quite useful for
during of the turning of a sash. The adjustable screw of the drill- an optimization of a warehouse and for logistics too.
in corner hinge was fixed primordially in the central position to
exclude unscrewing during transportation and exploitation of end
product.
6) The finger of the stay arm bearing gets the hard and reliable
fixation thanks to a special bush of high-strength polymer,
excluding the disconnection by itself.
7) The antitheft locking plates with mushroom pins of the corner
transmission and middle lock together allow equipping a window
according to requirements of the base safety according to AhS
Standard.
3
Protective plating of KOMFORT LINE K-3 General product
information
1) The prolonged exposure of high wetness (more than 70%). 4) Some cleaning agents include alkali, acid and so on.
2) The polluted air with gas, comprising a connection of various 5) Under the influence of different temperature there can appear
acids, and an exposure of salt-mist. the formation of condensate at the surface of hardware.
3) The mechanical damages of surface during an assembly or 6) The pollution with some building materials, in particular by
maintenance, which disrupt wholeness of the plating. cement or gypsum plaster.
1) Avoid hits of building materials at the hardware surface, for 4) The cleaning should be made with pH-neutral solute, before
example plaster, cement, different building solutes and building diluted.
dust.
Storage conditions
This applies to storage and transport, as well as for unloading and loading procedures. Where appropriate, plastic protective sheets or
similar are to be used during outdoor transport when raining (i.e. on-site transport). Storage may only be carried out in suitable, closed
rooms and not outdoors. Condensation is to be absolutely avoided during the entire transport and storage duration.
1) Always keep the hardware boxes closed, and always cover up 3) The components may not get wet. The packaging must remain
hardware boxes which were opened and do not put boxes directly dry (it is recommended: Warehouse temperature – 15-25˚C;
on the floor. Relative humidity – less then 50%).
2) Transport the hardware always with suitable devices (if 4) If box becomes wet please immediately unpack the
possible on pallets with stretch film). components from the wet bundles, dry the components and
check for signs of corrosion. In any case repack the usable
components when dry with new packing material.
4
Basic notations and representation
General product
of the information information
Basic notations
Tilt-only sash
Turn-only sash
All article numbers in this catalogue were afforded an alphanumeric form. The decipher of all article numbers you can find at the
pages 8-9.
Thus, all sizes which were shown in that catalogue are nominal and contain general tolerances.
All sizes were confered in mm.
The information about restriction of sashes’ sizes should be taken from diagrams of this catalogue or a user’s guide.
5
Section of PVC profiles
General product
for single sash and double one information
9
min. 12
18-22
13
min. 12
18-22
min. 12
18-22
min. 12
18-22
The information about profile-depending elements you find at the profile list
6
Recommendations for profile design -
General product
PVCu windows information
6. 5.
B
+1,0 3 ±0,5
- 0,5
3.
min.16
+0,5
Center A
1.
12 – 0,5
+1,5
A ±0,3
Width
18/20/22 mm
of hinge
Sash groove position 9 17 ±0,2
Sash groove position 13 21 ±0,2
Center B
1. The tolerance of width for top sash’s hinge.
2. Necessary distance for moving the hardware.
3. Gap for hinge.
300
4. Sash overlap.
7.
5. Necessary distance for the clamping of gasket adjustment.
6. Necessary distance for inserting a hinge into sash overlap.
7. Necessary distance for operation of small turn and tilt-turn
Screw Centring Groove sashes.
Center B
+0,2 +0,2
16,2 - 0,1 16,2 - 0,1
+0,2 +0,2
12,2 - 0,1 12,2 - 0,1
2,2 ± 0,2
2,2 - 0,2
9,3 ± 0,2
9,3 - 0,2
2,8
7
Article structure General product
information
Article structure
1 2 3 4 5 6 7 8 9 10 11
XXXXX-XX-XXXX
Modification index
Color
Packaging quantity
Type of opening
Size
Number of subgroup
Product group
Product class
8
Article structure General product
information
Double encoding can be used for several tones of the same color.
Example: 1 – white color RAL 9016
1B – white color RAL 9010
9
Application range diagrams General product
information
Gla
2300 2300
Gl
Gla
ss w
2200 2200
as g/sq
22
Gl
s w .m
ss
2100
we
eig
ht
sw
2000 2000
33
ht
ig
Gl
eig
as
ht
kg/
1900 1900
ht
sw
42
sq.
33
1800 1800
eig
m
kg
kg
1700 1700
ht
/sq
/sq
240-mm middle lock 240-mm middle
42
1600 1600
.m
.m
k
1500 1500
sq
1400
1300 1300
1200 1200
Sash rebate height, mm
Sash rebate height, mm
1100 1100
1000 1000
900 900
800 800
700 700
600 600
500 500
400 400
370 370
300
400
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1520
300
400
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1520
Tilt sash
1600
1500
1400 One tilt stay arm should be
1300 installed on top
1200
1100
Sash rebate height, mm
1000
900 Two tilt stay arms should be
800 installed on top
700
600
500
400
300
280
300
400
500
600
700
800
900
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
2000
10
Incorrect using and safety General product
information
Risk of injury or damage from pressing the sash against the reveal
• Do not press the sash against the window reveal.
Risk of injury from trapping parts of the body between the sash and the frame
• Do not insert obstructions into the opening between sash and frame.
11
Certificates General product
information
ROSENHEIM
ZERTIFIZIERT
CERTIFIED
12
Hinges
Hinges
Section 1
Corner bearing
Hinges
3
3
Axis position
± 2*
77
18
46
* horizontal adjustment, mm The groove for glazing bead
14
15,5
1
Corner bearing
Hinges
22 Axis position
± 2*
18
46
77
The groove for glazing bead
* horizontal adjustment, mm
14
15,5
1
± 2*
15
- used for 18-22 mm sash overlap;
- for appropriate sash hinge look at p. 13; 50
* vertical adjustment, mm
15
32*
23,5**
12
6
Clamp adjustment,
± 2*
±0.8 mm
15
50
* vertical adjustment, mm
35*
23,5**
Drill-in corner hinge with gasket Сover of the drill-in corner hinge
pressure adjustment, 6x16/26
16
6
26
Clamp adjustment,
± 2*
±0.8 mm
15
50
* vertical adjustment, mm
35*
23,5**
16
6
± 2*
15
50
* vertical adjustment, mm
32*
23,5**
2 screws from 80 kg
sash weight
± 2*
105
46
Cover of rebate corner
hinge
35,5
79 10,5
Side
Description А С B kg Part No.
opening
3
3
Axis position
15,5
1
- the pin is supplied with hinge.
14
Sash Size “А”
18
46
77
overlap
18 18,5
20 20,5
21 21,5
12
6
Axis position
15,5
1
14
Sash Size “А”
18
46
77
overlap
18 18,5
20 20,5
21 21,5
24
6
Axis position
15,5
- for decorative covers in other colors look at p. 26;
1
- the pin is supplied with hinge.
14
Sash Size “А”
18
46
77
overlap
18 18,5
20 20,5
21 21,5
± 2*
± 2**
Middle hinge
Hinges
751-1710 1
Middle hinge 12/20-9 12 20 9 50* 2 / 4х25 100 A7030-09-N03
1711-2360 2
751-1710 1
Middle hinge 12/20-13 12 20 13 50* 2 / 4х25 100 A7030-13-N03
1711-2360 2
751-1710 1
Сover of top sash hinge ― ― ― ― ― 500 A7004-10-N**
1711-2360 2
А - sash rebate gap / С - sash overlap / В - sash groove position
* - for 2-hinges set
** – for decorative covers in other colors look at p. 26
25
Section 1
Covers
Hinges
26
Gears
Gears
Section 2
Drilling and milling a sash
for 15-mm backset gear Gears
Ø 10
43 Ø 12
51
Ø 10
Size G
15 12 12
15
27
Section 2
Drilling and milling a sash
for 25, 30, 35-mm backset gear Gears
Drilling and milling a sash for 25, 30, 35-mm backset gear,
handle position is central
Backset A1
Ø10 mm
Ø12 mm
43
81
Ø10 mm
G
12
Backset
25 12,4 15,5
30 12,4 15,5
35 12,4 15,5
28
Section 2
Drilling and milling a sash
for 25, 30, 35-mm backset gear Gears
Drilling and milling a sash for 25, 30, 35-mm backset gear,
lockeble, handle position is central
Backset A1
Ø10 mm
Ø12 mm
81
43
Ø10 mm
X
Ø12 mm
G
Ø20 mm
81
63
16
Ø20 mm
Ø12 mm
12
Backset A2
Backset
25 12,4 15,5
30 12,4 15,5
35 12,4 15,5
29
Section 2
Minimum cut
dimension
C-2
A
The place for сover for
gear with customer logo
D
B
150
30
Section 2
Dimensions
SRH Part No.
Description
(mm)
G A B C C-2 D
Tilt and turn variable gear 0,
450-550 225-275 250 125 – – – – – – 20 K1001-02-N03
L=250, 450-550*
31
Section 2
Minimum cut
dimension
С 1
А
32
Section 2
Dimensions
SRH Part No.
Description
(mm)
G A B C C-1
Constant gear 0**,
360-550 140 400 0 0 0 – – 1 20 K1004-04-N03
L=400, 360-550
Constant gear 1,
400-500 175 350 - - - – – 2 20 K1004-03-N03
L=350, G=175, 400-500*
Constant gear 2,
480-680 200 530 - - - – – 3 20 K1004-05-N03
L=530, G=200, 480-680*
Constant gear 3,
681-920 300 770 - 120 - 1 – 5 20 K1004-08-N03
L=770, G=300, 681-920
Constant gear 4,
921-1160 450 1010 - 120 - 1 – 5 20 K1004-10-N03
L=1010, G=450, 921-1160
Constant gear 5,
1161-1400 600 1250 - 120 - 1 – 7 20 K1004-12-N03
L=1250, G=600, 1161-1400
Constant gear 6,
1401-1640 600 1490 - 120 438 2 – 8 20 K1004-15-N03
L=1490, G=600, 1401-1640
Constant gear 7,
1641-1880 600 1730 - 120 643 2 – 9 10 K1004-17-N03
L=1730, G=600, 1641-1880
Constant gear 8,
1641-1880 1000 1730 280 263 - 2 – 10 10 K1004-18-N03
L=1730, G=1000, 1641-1880
Constant gear 9,
1881-2120 1000 1970 280 387 - 2 – 11 10 K1004-20-N03
L=1970, G=1000, 1881-2120
Constant gear 3,
681-920 300 770 - 120 - – 1 5 20 K1034-08-N03
L=770, G=300, 681-920
Constant gear 4,
921-1160 450 1010 - 120 - – 1 5 20 K1034-10-N03
L=1010, G=450, 921-1160
Constant gear 5,
1161-1400 600 1250 - 120 - – 1 7 20 K1034-12-N03
L=1250, G=600, 1161-1400
Constant gear 6,
1401-1640 600 1490 - 120 438 – 2 8 20 K1034-15-N03
L=1490, G=600, 1401-1640
Constant gear 7,
1641-1880 600 1730 - 120 643 – 2 9 10 K1034-17-N03
L=1730, G=600, 1641-1880
Constant gear 8,
1641-1880 1000 1730 280 263 - – 2 10 10 K1034-18-N03
L=1730, G=1000, 1641-1880
Constant gear 9,
1881-2120 1000 1970 280 387 - – 2 11 10 K1034-20-N03
L=1970, G=1000, 1881-2120
A
G
Minimum cut
dimension
50
150
34
Section 2
Dimensions
SRH Part No.
Description
(mm)
G A B C D
Constant gear
400-600 180 400 — — — — 0 20 K1006-04-N03
L=400, G=180, 400-600*
Constant gear
601-800 300 500 — — — — 2 20 K1006-05-N03
L=500, G=300, 601-800**
Constant gear
801-1000 400 700 — 480 — 1 3 20 K1006-07-N03
L=700, G=400, 801-1000
Constant gear
1001-1200 500 900 — 680 — 1 5 20 K1006-09-N03
L=900, G=500, 1001-1200
Constant gear
1201-1400 500 1100 — 680 — 1 6 20 K1006-11-N03
L=1100, G=500, 1201-1400
Constant gear
1401-1600 500 1300 — 780 — 1 7 20 K1006-13-N03
L=1300, G=500, 1401-1600
Constant gear
1601-1800 700 1500 — 780 1280 2 7 20 K1006-15-N03
L=1500, G=500, 1601-1800
Constant gear
1801-2000 1000 1700 780 1280 — 2 10 10 K1006-17-N03
L=1700, G=1000, 1801-2000
Constant gear
2001-2200 1000 1900 780 1580 — 2 11 10 K1006-19-N03
L=1900, G=1000, 2001-2200
Constant gear
2201-2400 1000 2100 580 1280 1680 3 11 10 K1006-21-N03
L=2100, G=1000, 2201-2400
35
Section 2
Minimum cut
dimension
C-2
A
D
36
Section 2
Dimensions
SRH Part No.
Description
(mm)
G A B C C-2 D
37
Section 2
Tilt and turn variable gear, handle position is central, backset 25, 30, 35 mm.
Minimum cut
dimension
C1
150
38
Section 2
Dimensions
SRH Part No.
Description
(mm)
A B C C-1 D G
* 2-side handle, locking parts with through holes with a diameter of 6.5 mm;
** locking parts with threaded holes M5;
39
Section 2
Minimum cut
dimension
C1
150
40
Section 2
Dimensions
Description SRH Part No.
(mm)
A B C C-1 D G X
* 2-side handle, locking parts with through holes with a diameter of 6.5 mm;
** locking parts with threaded holes M5.
- lockable;
- handle position is central.
41
Section 2
Turn gear
Gears
Turn gear
A
D
C
42
Section 2
Turn gear
Gears
Dimensions
SRH Part No.
Description
(mm)
A B C D E F
Turn gear 1 L=300,
300-500 300 150 96 ― 79 ― 2 — 2 20 K1003-03-N03
300 - 500, 2ML
Turn gear 2 L=400,
401-600 400 200 146 ― 129 ― 2 — 2 20 K1003-04-N03
401 - 600, 2ML
Turn gear 3 L=600,
601-800 600 300 246 ― 229 ― 2 — 4 20 K1003-06-N03
601 - 800, 2ML
Turn gear 4 L=800,
801-1000 800 400 346 ― 329 ― 2 — 4 20 K1003-08-N03
801 -1000, 2 ML
Turn gear 5 L=1000,
1001-1200 1000 500 446 ― 429 101 3 — 8 20 K1003-10-N03
1001 - 1200, 3 ML
Turn gear 6 L=1200,
1201-1400 1200 600 546 ― 530 101 3 — 8 20 K1003-12-N03
1201 - 1400, 3ML
Turn gear 7 L=1400,
1401-1600 1400 700 646 ― 629 101 3 — 8 20 K1003-14-N03
1401 - 1600, 3ML
Turn gear 8 L=1600,
1601-1800 1600 800 746 318 729 301 4 — 8 10 K1003-16-N03
1601 - 1800, 4ML
Turn gear 9 L=1800,
1801-2000 1800 900 846 318 829 301 4 — 10 10 K1003-18-N03
1801 - 2000, 4ML
Turn gear 10 L=2000,
2001-2200 2000 1000 946 318 929 301 4 — 10 10 K1003-20-N03
2001 - 2200, 4ML
Turn gear 11 L=2200,
2201-2400 2200 1100 1046 318 1029 301 4 — 11 10 K1003-22-N03
2201 - 2400, 4ML
Turn gear 1 L=300,
300-500 300 150 96 ― 79 ― — 2 2 20 K1033-03-N03
300 - 500, 2ML, Se
Turn gear 2 L=400,
401-600 400 200 146 ― 129 ― — 2 2 20 K1033-04-N03
401 - 600, 2ML, Se
Turn gear 3 L=600,
601-800 600 300 246 ― 229 ― — 2 4 20 K1033-06-N03
601 - 800, 2ML, Se
Turn gear 4 L=800,
801-1000 800 400 346 ― 329 ― — 2 4 20 K1033-08-N03
801 -1000, 2 ML, Se
Turn gear 5 L=1000,
1001-1200 1000 500 446 ― 429 101 — 3 8 20 K1033-10-N03
1001 - 1200, 3 ML, Se
Turn gear 6 L=1200,
1201-1400 1200 600 546 ― 530 101 — 3 8 20 K1033-12-N03
1201 - 1400, 3ML, Se
Turn gear 7 L=1400,
1401-1600 1400 700 646 ― 629 101 — 3 8 20 K1033-14-N03
1401 - 1600, 3ML, Se
Turn gear 8 L=1600,
1601-1800 1600 800 746 318 729 301 — 4 8 10 K1033-16-N03
1601 - 1800, 4ML, Se
Turn gear 9 L=1800,
1801-2000 1800 900 846 318 829 301 — 4 10 10 K1033-18-N03
1801 - 2000, 4ML, Se
Turn gear 10 L=2000,
2001-2200 2000 1000 946 318 929 301 — 4 10 10 K1033-20-N03
2001 - 2200, 4ML, Se
Turn gear 11 L=2200,
2201-2400 2200 1100 1046 318 1029 301 — 4 11 10 K1033-22-N03
2201 - 2400, 4ML, Se
43
Section 2
Turn gear
Gears
A
F
44
Section 2
Turn gear
Gears
Dimensions
SRH Part No.
Description
(mm)
A B C D F G
45
Section 2
Double-sash gear with
integrated locking plates Gears
Integrated locking
plate
С-2
С
A
D
balcony catch
B
46
Section 2
Double-sash gear with
integrated locking plates Gears
Dimensions
SRH Part No.
Description
(mm)
A B C D C-2 E
Double-sash gear* 1
551-750 450 265 — — — 225 0 3 20 K1002-04-N03
L=450, 551-750
Double-sash gear 2
751-950 650 393 129,5 — — 325 1 4 20 K1002-06-N03
L=650, 751-950
Double-sash gear 3
951-1430 1130 393 129,5 — — 565 1 6 20 K1002-11-N03
L=1130, 951-1430
47
Section 2
Integrated locking
plate
balcony catch
G
B
48
Section 2
Dimensions
SRH Part No.
Description
(mm)
G A B C D
49
Section 2
Integrated locking
plate
D
C
50
Section 2
Dimensions
SRH Part No.
Description
(mm)
G A B C D
51
Section 2
Gear for sliding system,
backset 15 mm. Gears
9,5
Ø 4,4
Ø 8,2
G
Ø6
18
A
C
D
52
Section 2
Gear for sliding system,
backset 15 mm. Gears
Dimensions
SRH Part No.
Description
(mm)
A B C D E F G
53
Section 2
Gear for sliding system,
backset 7,5 mm Gears
9,5
Ø 4,4
Ø 8,2
G
.
F
Ø6
18
A
C
D
54
Section 2
Gear for sliding system,
backset 7,5 mm Gears
Dimensions
Description SRH (mm) Part No.
A B C D E F G
55
Extensions
Middle locks
Corner transmissions
Corner transmissions
Middle locks / Extensions
Section 3
150
60
150
60
150
Application range
Description Part No.
SRW (mm) SRH (mm)
57
Section 3
60
150
150
60
60
150
Application range
Description Part No.
SRW (mm) SRH (mm)
58
Section 3
114 114
50 50
60
150
150
A B С
Application range
Description Side opening Part No.
SRW
SRH (mm)
(mm)
Narrow corner transmission,
А 300-400 450-2390 1 — 3 50 K2003-00-N03
50х150
Narrow corner transmission,
B 400-600 370-450 1 — 3 50 K2003-00-N03
50х150
Narrow corner transmission,
А 300-400 450-2390 — 1 3 50 K2006-00-N03
1 ML, Se, 50х150,
Narrow corner transmission,
B 400-600 370-450 — 1 3 50 K2006-00-N03
1 ML, Se, 50х150,
Narrow corner transmission,
C 400-600 300-350 — 1 3 50 K2006-00-N03
1 ML, Se, 50х150,
Narrow corner transmission,
А 300-400 450-2390 — — 3 50 K2017-00-N03
without locking pin
Narrow corner transmission,
B 400-600 370-450 — — 3 50 K2017-00-N03
without locking pin
59
Section 3
150
- separate transmissions for left and right opening;
60
- provides 3 type-sizes of ventilation;
- ventilation slit 12,16, 20 mm.
12
100
150
60 60
- separate transmissions for left and right opening;
- provides 3 type-sizes of ventilation;
12
12
Application range
Description Part No.
SRW
SRH (mm)
(mm)
Corner transmission, integrated slit, left 400-1520 450-2390 1 — 4 50 K2004-00-L03
Corner transmission, integrated slit, 1 ML, Se, left 400-1520 450-2390 — 1 4 50 K2014-00-L03
Corner transmission, integrated slit, 1 ML, Se, right 400-1520 450-2390 — 1 4 50 K2014-00-R03
Locking plate for integrated slit (frame part) look at the section “Profile-depending elements”
60
Section 3
150
60
51
150
71
60
150
Application range
Description Part No.
SRW (mm) SRH (mm)
61
Section 3
B
A
Sash rebate
4 mm B
Outer edge of
C
middle lock or
its extension
A
B
- not intended for WK security level.
A
- for additional locking point;
- for height > 1710 mm.
SRW Dimensions
Description SRH (mm) Part No.
(mm)
A B* C*
Middle lock L=400, 1 ML 600-1000 600-1000 400 280 ― 1 3 20 K4001-04-N03
SRW
Dimensions
Description SRH (mm) Part No.
(mm)
A B C
Middle lock extension 480 mm 1710-2210 1280-1520 480 360 ― 1 4 20 K4005-05-N03
*Dimensions B and C are distances from the outer edge of middle lock or its extension to the locking pin axis
62
Section 3
B
A
B
Sash rebate
4 mm
Outer edge of
C
middle lock or
its extension
A
B
- not intended for WK security level.
A
- for additional locking point;
- for height > 1710 mm.
SRW Dimensions
Description SRH (mm) Part No.
(mm)
A B* C*
Middle lock L=400, 1 ML, Se 600-1000 600-1000 400 280 ― 1 3 20 K4017-04-N03
SRW
Dimensions
Description SRH (mm) Part No.
(mm)
A B C
Middle lock extension, Se, 480 mm 1710-2210 1280-1520 480 360 ― 1 4 20 K4025-05-N03
*Dimensions B and C are distances from the outer edge of middle lock or its extension to the locking pin axis
63
Section 3
B
A
Sash rebate C
4 mm
Outer edge of
D
middle lock or
its extension
A
B
- for additional locking point;
A
Additional locking
- for height > 1710 mm.
pin upwardly
B
A
Sash rebate
C
4 mm
middle lock or
its extension Se, 680 mm
A
A
Additional locking - for additional locking point;
pin upwardly
- for height > 1710 mm.
*Dimensions B,C and D are distances from the outer edge of middle lock or its extension to the locking pin axis
65
Section 3
Middle lock with additional
Corner transmissions
mushroom pin Middle locks
B
A
Sash rebate
C
4 mm
Outer edge of
middle lock or
its extension
Middle lock extension
680 mm
D
B
- for additional locking point;
A
Additional locking
pin upwardly - for height > 1710 mm.
Dimensions B,C and D are distances from the outer edge of middle lock or its extension to the locking pin axis
66
Section 3
Extension lock
А
90
67
Section 3
411
480
411
480
413
240
68
Section 3
Middle connection
Minimum cut
dimension
C1
A
C
69
Section 3
Dimensions
Description SRW (mm) Part No.
A B C С-1
Middle connection
551-750 450 225 ― ― ― ― 2 20 K4013-05-N03
L = 450, 551-750
Middle connection
751-950 650 325 ― ― 1 ― 4 20 K4013-07-N03
L = 650, 751-950
Middle connection
951-1430 1130 565 ― — 1 ― 4 20 K4013-11-N03
L = 1130, 951-1430
Middle connection
1431-1910 1610 805 330 330 2 ― 8 10 K4013-16-N03
L = 1610, 1431-1910
Middle connection
1011-2390 2090 1045 595 595 3 ― 10 10 K4013-21-N03
L = 2090, 1911-2390
Middle connection*
751-950 650 325 ― ― ― 1 4 20 K4033-07-N03
L = 650, 751-950, Se
Middle connection*
951-1430 1130 565 ― — ― 1 4 20 K4033-11-N03
L = 1130, 951-1430, Se
Middle connection*
1431-1910 1610 805 330 330 ― 2 8 10 K4033-16-N03
L = 1610, 1431-1910, Se
Middle connection *
1011-2390 2090 1045 595 595 ― 3 10 10 K4033-21-N03
L = 2090, 1911-2390, Se
70
Section 3
Bottom extension
150
71
Section 3
1
150
1
150
11,5
third parties without written authority from the proprietor
third parties without written authority from the proprietor
185
185
Він не повинен бути скопійований, розмножений або передаватися
Він не повинен бути скопійований, розмножений або передаватися
11,5
Approved BY
date / by :
Material :
Checked
date / by :
Weight : 0,120 кг
Created
date / by :
18.01.2018 ML Surface area : 18035,579 мм^2
Creation
Revision No Rev. Date Made by Explanation of the revision Project No : A-10109
Revision: NoSILVER
Surf. treatment Rev. Date Made by
- latch outlet 11,5 mm; Description : Scale : 1:1
SINGLE SHOOT BOLT, BOTTOM Drawing No :
- not destined for safety level;
Ind:
K4035-01-N03
- connection of middle lock is available.
73
Section 3
Bottom extension for turn sash 180° (top) Bottom extension for turn sash 180° (top), Se
45
45
150
150
- connection of middle lock is available. - connection of middle lock is available.
Bottom extension for turn sash 90° (bottom) Bottom extension for turn sash 90° (bottom), Se
150
150
45
45
74
Stay arm
Stay arm
Section 4
Stay arm
Stay arm
Stay arm
± 1* ± 2**
Stay arm, Se
± 1* ± 2**
* clamp adjustment, mm
** horizontal adjustment, mm
Dimensions
Description SRW (mm) kg Part No.
A B
Stay arm 2+ML, L=650, 601-800, 1 ML 601-800 650 390 1 — 130 4 18 K3001-57-N03
Stay arm 2+ML, L=650, 601-800, 1 ML, Se 601-800 650 390 — 1 130 4 18 K3021-57-N03
75
Section 4
SRW Dimensions
Description kg Part No.
(mm)
A B
Stay arm, sash part, L= 485, 400-600 400-600 450 ― — — 130 3 20 K3013-05-N03
Stay arm, sash part, L= 685, 601-800 601-800 650 ― — — 130 4 20 K3013-07-N03
Stay arm, sash part, 2+ML, L= 685, 601-800 601-800 650 390 1 — 130 4 20 K3013-57-N03
Stay arm, sash part, L= 925, 801-1040, 1 ML 801-1040 890 537 1 — 130 6 10 K3013-09-N03
Stay arm, sash part, L= 1165, 1041-1280, 1 ML 1041-1280 1130 624 1 — 130 7 10 K3013-11-N03
Stay arm, sash part, L= 925, 801-1040, 1 ML 801-1040 890 537 — 1 130 6 10 K3023-09-N03
Stay arm, sash part, L= 1165, 1041-1280, 1 ML 1041-1280 1130 624 — 1 130 7 10 K3023-11-N03
76
Section 4
* clamp adjustment, mm
** horizontal adjustment, mm
Stay arm, frame part 13, L=248, 400-600, left 400-600 L 12 20 13 10 K3011-02-L03
Stay arm, frame part 13, L=248, 400-600, right 400-600 R 12 20 13 10 K3011-02-R03
Stay arm, frame part 13, L=319, 601-800, left 601-800 L 12 20 13 10 K3011-03-L03
Stay arm, frame part 13, L=319, 601-800, right 601-800 R 12 20 13 10 K3011-03-R03
Stay arm, frame part 13, L=449, 801-1040, left 801-1040 L 12 20 13 10 K3011-04-L03
Stay arm, frame part 13, L=449, 801-1040, right 801-1040 R 12 20 13 10 K3011-04-R03
Stay arm, frame part 13, L=539, 1041-1280, left 1041-1280 L 20 20 13 10 K3011-05-L03
Stay arm, frame part 13, L=539, 1041-1280, right 1041-1280 R 20 20 13 10 K3011-05-R03
± 1** ± 2***
** clamp adjustment, mm
*** horizontal adjustment, mm
Dimensions
Description SRW (mm) kg Part No.
A B
Stay arm 1, "First Tilt",
400-600 450 ― — — 130 3 20 K3014-05-N03
L=450, 400-600
Stay arm 2, "First Tilt",
601-800 650 ― — — 130 4 20 K3014-07-N03
L=650, 601-800
Stay arm 3, "First Tilt",
801-1040 890 537 1 — 130 6 10 K3014-09-N03
L=890, 801-1040
Stay arm 4, "First Tilt",
1041-1280 1130 624 1 — 130 7 10 K3014-11-N03
L=1130, 1041-1280
Stay arm 3, "First Tilt",
801-1040 890 537 — 1 130 6 10 K3024-09-N03
L=890, 801-1040, Se
Stay arm 4, "First Tilt",
1041-1280 1130 624 — 1 130 7 10 K3024-11-N03
L=1130, 1041-1280, Se
78
Section 4
± 1*
124
± 2**
± 0,8*
79
* clamp adjustment, mm
** horizontal adjustment, mm
79
Section 4
Tilt stay arm
(fixing on a gear) Stay arm
Adjustment plate*
29,5 109
168
187
81
Additional elements
Additional
elements
Section 5
Фальц рамы
12
98
Balcony catch
Additional elements
Balcony catch М
70
98
17
98
17
± 3*
* horizontal adjustment, mm
SRH/SRW
Description А С B Part No.
(mm)
Concealed middle hinge 751-1710 1
12 20 13 2 / 4х35 100 A7057-13-N03
frame part 12/20-13 1711-2360 2
Concealed middle hinge 751-1710 1
12 20 9 2 / 4х35 100 A7057-09-N03
frame part 12/20-9 1711-2360 2
Concealed middle hinge 751-1710 1
— — — 2 / 4х25 100 A7056-00-N03
sash part 1711-2360 2
Middle hinge
Additional elements
Middle hinge
SRH/SRW
Description Part No.
(mm)
751-1710 1
Middle hinge with cover (white) 4 / 4х25 100 A7045-00-N01
1711-2360 2
751-1710 1
Middle hinge with cover (brown) 4 / 4х25 100 A7045-00-N02
1711-2360 2
88
Section 5
12
16
89
Section 5
15,5
12
16
73
90
Hardware set combinations
combinations
Hardware set
Section 6
10 10
26 10
3 17 15
27 10 5a
28 5 18
2
4 16
10
6
10a 15a
6a
Application range:
Width: 300 – 1520**mm
Height: 370* – 2390 mm
10 10
1
12
7
11 1a
38 29 29b 38a
10
14с
8 2a
36 19 20
9 6 14
21 13
10b 10 10
91
Section 6
92
Section 6
93
Section 6
10 26 10
3
10 15a
27 10 17
28
5b
2 16 15 18
4
10
10a
Application range:
Width: 400 – 1520 mm
6
Height: 370 – 2390 mm
6a
10 10
12
11 7
10
14с
2a
19 13 20
36
14
10
10с
21
94
Section 6
95
Section 6
96
Section 6
Turn set
10
17 15
34a 6 22
10 10
18
2 36
16
4
15a
Application range*:
Width: 280 – 1280 mm
Height: 450 – 2390 mm
30 31 31a
10
1
12
11
30 31 31a
38 29 29b 38a
14с
4
10 19 20
2
36
14
34
6
10 10 21 13
Turn set
17
15
22
18
16
10
15a
Application range:
Width: 280 – 700 mm
Height: 300 – 2400 mm
30 31 31a
10
37
38 29 29b 38a
30 31 31a
14с
19 20
14
21 13
99
Section 6
100
Section 6
Tilt set
33 10
10 10
34 34a
1
2 2
4 4
Application range:
Width: 450 – 2000 mm
10 6 6
Height: 280 – 1600 mm
10
36 36
10
10
32 30 32
31
15 15
18 31a 18
17 17
101
Section 6
102
Section 6
Tilt set
10 33 10 10
37
Application range:
Width: 300 – 2000 mm
Height: 280 – 700 mm
30 32
31
15 15
18 31a 18
17 17
10 10
17
15 22
18 36
2
16
15a
Application range:
Width: 400 – 1280 mm
Height: 550 – 2390 mm
31a 31 30
23a
31a 31 30
38b* 29a*
24
14с
20 19
36 25
14 6
13 21
10 10 10a 35
104
Section 6
Main sash
26 10
10
27 10
17
5a 15
5 18
2
16
6 10a
6a 15a
Application range:
Width: 400 – 1280 mm
Height: 550 – 2390 mm
10
1
12
7
29b* 38a*
10
14с
8 2a
19 20
36
6 14
21 13
10b 10 10
106
Section 6
107
Section 6
17 15a
10 10
22 36
18 15 16 2
Application range:
Width: 400 – 1280 mm
Height: 550 – 2390 mm
31a 31 30
38b 29a
23a
31a 31 30
24
14с
20 13 19 14
2a
36
21 10 10a
108
Section 6
26 10
10 10 15a 17
27
5b
2 16 15 18
10a
Application range:
Width: 400 – 1520 mm
6
Height: 550 – 2390 mm 6a
10
29b 38a
12
10
14с
2a
14 19 13 20
36
10с 10
21
109
Section 6
110
Section 6
111
Tools
Instalation
Adjustments
Tools / Instalation
Adjustments
Section 7
Stay arm 4
Stay arm 3
Stay arm 2
6
7
81 394
For corner transmission 541
1 For corner with locking 628
transmission with pin vertically
locking pin vertically
155
2 For corner transmission For middle lock
305
with locking with additional
pin vertically locking pin
variable 6
555
Middle lock 400
725
Gear
1035
variable 5
1268
variable 2, 3, 4
604
1715
Gear
Gear
274
129
129
For microli
For microli
Middle
160
160
lock 1130 5
282
382
482
variable 6 variable 5
variable 4
Middle lock650 +
Gear
Gear
4
138
288
538
708
1018
All dimensions are approximate and are subject to verification during production start-up.
113
Section 7
Information for an adjustment
Installation
of jigs constant gear Tools
Stay arm 4
Stay arm 3
Stay arm 2
6
7
81 394
For corner transmission 541
with locking 628
pin vertically
9 3
155
Locking plate
2121-2360 1744
For middle lock
305
with additional
locking pin
555
Middle lock 400
725
Locking plate 1408
1881-2120
8
1035
Locking plate
1641-1880 1284 1264 Locking plate Middle lock 650
1641-1880
1268
Locking plate
2121-2360 1141
Middle lock 820
Locking plate 1515
1059 1401-1640
Wrong operation
1715
safety device
liing plate
1641-1880
1881-2120
2121-2360 852
Locking plate
1161-1400 Middle
Locking plate 1401-1640 5
1641-1880 741 741 1641-1880 lock 1130
1881-2120
2121-2360
Locking plate
591 921-1160
Middle lock650 +
Extension lock 480
Locking plate
Wrong operation 452 681-920
safety device
liing plate
1161-1400
1401-1640 Wrong operation safety
1641-1880 302 device liing plate Middle lock 1130 +
921-1160 Extension lock 480
Wrong operation safety
152 device liing plate
681-920
Middle lock 1130 +
Extension lock 680
0 0
For constant tilt & turn gear For constant tilt & turn gear
8, 9,10 3, 4, 5, 6, 7
with additional pin
4
138
288
538
708
1018
All dimensions are approximate and are subject to verification during production start-up.
114
Section 7
5 Linear jig MLEV For all vertical middle lock extensions. A7027-00-N00
7 Linear jig CTCP 1 For corner transmission with vertical locking pin. A7025-00-N00
115
116
583
For extension lock
319 of corner transmission
64
Corner transmission
394
155
Middle
Stay arm 601-800 lock
305
541 L=400
Stay arm 801-1040 Middle
628 lock
555
Stay arm 1041-1280 L=650 Middle
lock
725
L=820
Middle
lock Middle
lock
1035
L=1130
Installation of frame hardware components
L=650
+
Middle
1235
Extension
lock lock
680 L=1130
Gear variable +
1515
604
1911-2390 Extension Middle lock
Gear lock L=1130
variable Gear 480 +
1715
274
751-1230
950-1430 1431-1910 680
129
Installation of frame hardware components
1231-1710
1911-2390
Li
ing
160
plate
Gear Gear
variable variable
382
282
1231-1710 1431-1910 Gear variable
482
1911-2390
1018
Tools
Installation
64
Middle
Corner transmission 394 lock
155
305
Stay arm 601-800 L=400
Middle
541 lock
Stay arm 801-1040 L=650
555
628 Middle
Stay arm 1041-1280 lock
725
L=820
Middle Middle
lock lock
1035
L=1130 L=650
1235 +Extension
lock 680
Installation of frame hardware components
Middle
lock
L=1130
1515
+Extension
Size Х for constant gear: lock 480
681-920 - 152 mm
921-1160 - 302 mm Middle
lock
1161-1400 L=1130
1401-1640 - 452 mm +Extension
1715
Installation of frame hardware components
1745
1641-1880 lock 680
1641-1880
1881-2120 - 852 mm
2120-2360
1265
Middle lock L=1130
1142
708
1060
742
1401-1640, 1881-2120
288
Middle lock
442
L=400
565
For extension lock
of corner transmission
117
Section 7
Turn gear 9,
L=1800, 1801-2000
Turn gear 8,
L=1600, 1601-1800
Turn gear 7,
L=1400, 1401-1600
1038
Turn gear 6,
L=1200, 1201-1400
938
838
Turn gear 5,
L=1000, 1001-1200
Turn gear 3,
L=600, 601-800
538
Turn gear 7,
L=1400, 1401-1600
Turn gear 6, Turn gear 2,
L=1200, 1201-1400 L=400, 401-600
438
338
Turn gear 5,
L=1000, 1001-1200
238
Turn gear 1,
310
L=280, 280-400
138
110
88
0
87
137
Turn gear 1,
237
L=280, 280-400
337
Turn gear 2,
L=400, 401-600
309
437
Turn gear 3,
537
L=600, 601-800
637
Turn gear 8,
L=1600, 1601-1800
737
Turn gear 9,
L=1800, 1801-2000 Turn gear 4,
Turn gear 10, L=800, 801-1000
837
L=2000, 2001-2200
Turn gear 11,
937
L=2200, 2201-2400
Turn gear 5,
1037
L=1000, 1001-1200
Turn gear 6,
L=1200, 1201-1400
Turn gear 7,
L=1400, 1401-1600
Turn gear 8,
L=1600, 1601-1800
Turn gear 9,
L=1800, 1801-2000
118
Section 7
Drilling jig for frame hinges Drilling jig for sash hinges
4.
3.
1. 2.
Adjustment plate
Drilling jig for frame For drilling holes for top and bottom
12/20-13 drill Ø3 50 A7002-00-N09
hinges frame hinges
Drilling jig for frame For drilling holes for top and bottom
12/21-13 drill Ø3 50 A7002-20-N09
hinges frame hinges
Drilling jig for sash For drilling holes for bottom sash
12/20-13; 12/20-9 drill Ø3 80 A7003-00-N09
hinges hinge
Drilling jig for sash For drilling holes for bottom sash
12/21-13; 12/21-9 drill Ø3 80 A7003-20-N09
hinges hinge
Adjustment plate
- For sash jig adjustment - 1 10073-05-N08
0,5 mm
Adjustment plate
- For sash jig adjustment - 1 10073-07-N08
0,7 mm
Adjustment plate
- For sash jig adjustment - 1 10073-10-N08
1 mm
119
Section 7
Jigs for frame
Installation
hinges 130 kg Tools
Drilling jig for frame hinges 130 kg Drilling jig for sash hinges 130 kg
4.
3.
1. 2.
Adjustment plate
Drilling jig for frame For drilling holes for top and bottom
12/20-13 drill Ø3/6 50 A7002-10-N09
hinges 130 kg frame hinges
Drilling jig for frame For drilling holes for top and bottom
12/21-13 drill Ø3/6 50 A7002-30-N09
hinges 130 kg frame hinges
Drilling jig for sash For drilling holes for bottom sash
12/20-13; 12/20-9 drill Ø3/6 80 A7003-10-N09
hinges 130 kg hinge
Drilling jig for sash For drilling holes for bottom sash
12/21-13; 12/21-9 drill Ø3/6 80 A7003-30-N09
hinges 130 kg hinge
Adjustment plate
- For sash jig adjustment - 1 10073-05-N08
0,5 mm
Adjustment plate
- For sash jig adjustment - 1 10073-07-N08
0,7 mm
Adjustment plate
- For sash jig adjustment - 1 10073-10-N08
1 mm
120
Section 7
121
Section 7
Installation recommendations
Installation
Adjustment Tools
Pin installation
Hook
± 2 mm
± 2 mm
± 1 mm
± 0,8 mm ± 2 mm
± 2 mm ± 1 mm
± 0.8 mm
122
Section 7
Installation recommendations
Installation
Adjustment Tools
Locking
pin СP Rotation
direction
Adjustment
limits
Locking
pin MP Rotation
direction
Adjustment
limits
Installation recommendations
For hinge installation it is recommended to drill 3-mm hole in plastic and reinforce-
ment profile, then to screw the hinge with screws without drill-bit.
123
Section 7
Punching machines
The rulers
124
Section 7
An order of the
Installation
hardware installation Tools
5
2
16
Order of
Description
operations
8
14
125
Section 7
An order of
Installation
the hardware installation Tools
10 10
15
10
28
27
10a
An order
of opera- Description
tions
11
10
9 13
10b
126
Profile-depending elements
Profile-depending
elements
Tilt locking Locking plate Lifting plate Locking plate, Locking plate Safety locking Tilt safety locking Tilt locking plate Locking plate
Profile В plate integrated slit for adjustable plate plate «First Tilt» adjustable for shoot
Profile list
ALUPLAST IDEAL 2000 13 K6004-13-L/R03 A7012-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 K6002-13-N03
BROKELMANN 58 13 K6005-13-L/R03 A7034-13-N00 A6003- 13-N03 A6002-13-N03 A6004-00-N03 S6005-13-N03 S6006-13-N03 K6002-13-N03
GEALAN 13 K6009-13-L/R03 A7042-13-N03 A6003- 13-N03 A6002-13-N03 A6004-00-N03 S6014-13-N03 S6022-13-L/R03 K6002-13-N03
KBE 58/9 9 K6003-09-L/R03 A7013-09-N03 A6007-09-N03 A6005-09-N03 A6004-00-N03 S6003-09-N03 S6004-09-N03 K6002-09-N03
KBE 58/9 Plus 9 K6003-09-L/R03 A7043-09-N03 A6007-09-N03 A6005-09-N03 A6004-00-N03 S6003-09-N03 S6004-09-N03 K6002-09-N03
KBE 58/13 13 K6001-13-L/R03 A7011-13-N03 A6003- 13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 K6002-13-N03
MIROPLAST WDS 400 13 K6001-13-L/R03 A7011-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
MIROPLAST WDS 404 13 K6001-13-L/R03 A7011-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
elements
Section 8
MIROPLAST WDS 505 13 K6001-13-L/R03 A7011-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
Profile-depending
MIROPLAST WDS 800 13 K6001-13-L/R03 A7011-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
127
128
Locking plate Locking plate
Profile list
Tilt locking Locking plate, Safety locking Tilt safety Tilt locking plate
Profile В Locking plate Lifting plate for adjustable adjustable for shoot
plate integrated slit plate locking plate «First Tilt»
integrated slit bolt
REHAU BASIC DESIGN 13 K6004-13-L/R03 A7012-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 K6002-13-N03
REHAU BRILLANT DESIGN 13 K6004-13-L/R03 A7012-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
REHAU CLIMA DESIGN 13 K6004-13-L/R03 A7012-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
REHAU THERMO DESIGN 13 K6004-13-L/R03 A7012-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
SALAMANDER DESIGN 2D 13 K6004-13-L/R03 A7012-13-N03 A6013-13-N03 A6014-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
SALAMANDER DESIGN 3D 13 K6004-13-L/R03 A7012-13-N03 A6013-13-N03 A6014-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
VEKA SOFTLINE 58 13 K6001-13-L/R03 A7011-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
VEKA SOFTLINE 70 13 K6001-13-L/R03 A7011-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
VEKA TOPLINE AD 13 K6001-13-L/R03 A7011-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
WINTECH 532 (ISOTECH) 13 K6001-13-L/R03 A7011-13-N03 A6017-13-N03 A6015-13-N03 A6016-00-N03 S6007-13-N03 S6008-13-N03 K6002-13-N03
WINTECH 632 13 K6001-13-L/R03 A7011-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
WINTECH 742 13 K6001-13-L/R03 A7011-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
WINTECH 752 13 K6001-13-L/R03 A7011-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
elements
Section 8
WINTECH 80 13 K6001-13-L/R03 A7011-13-N03 A6003-13-N03 A6002-13-N03 A6004-00-N03 S6001-13-N03 S6002-13-N03 S6015-13-L/R03 K6002-13-N03
Profile-depending
129