{Total No. of Questions - 9] [Total No. of Printed Pages - 4]
(2127)
17189(N)
B. Tech 5th Semester Examination
Limit State Design of Concrete Structures-] (CBS)
CE-501
Time : 3 Hours wwweepaper-tk Max. Marks : 60
The candidates shail limit their answers precisely within the answer-
book (40 pages) issued to them and no supplementary/continuation
sheet will be issued.
Attempt one question each from Sections A, B, C and D.
Section E is compulsory. All questions carry equal marks.
Use of |S: 456-2000 is allowed. Use of SP: 16 (Charts and
Tables only) is allowed.
SECTION -A
What ts the role of water cement ratio in Concrete? (3)
Discuss the importance of curing of concrete on durability
characteristics of concrete. (3)
Describe the various types of the loads considered in the
design of structures? (3)
Compression test were performed on 39 samples of
150 mm x 150 mm x 150 mm cubes of concrete which
yielded at following compressive strengths in Nimm?.
26 28 32 34 36 32 34 32°27 35 26 34
28 29 30 34 35 34 27 28 24 28 34 36
Note :
4. (a)
(b)
(c)
(d)
25
28
28
29 30 32 25 30 30 31 32 28 30 32 33
Determine the Characteristic strength of the concrete. <3)2 17189
(a) Define idealized stress strain curve for different types of
steels. Discussing the salient features, demonstrate the
procedure to find stress value corresponding I. wiv
strain. 40)
oh
(b) What are the limitations of all three design philosophies
ie working stress method, Ultimate load method and Limit
State method. (6)
SECTION - B
(a) Using Limit state Method, find the moment of resistance
of a singly reinforced beam 300 mm wide and 417 mm
deep up to the center of the tensile reinforcement. The
overall depth of the beam is 450 mm. The beam is
reinforced with 3 bars of 16 mm diameter. The concrete
used is M20 Grade and steel used is Fe 415 grade. (6)
{b) Design a cantilever beam projecting 2.2 m beyond the
fixed end loaded with a superimposed load of 15 kNvm run
inclusive of its self weight. Using M20 grade of concrete
and Fe 500 grade of steel design the beam. The width ot
the beam is to be restricted to250 mm. ~ (6)
Design the panel BC of the continuous slab shown in figure
subjected to uniformly distributed imposed loads 10 kN/m?
inclusive of self-weight of slab using M 20 and Fe 415. The load
of floor finish is 0.75 kN/m?. The span dimensions shown in the
figure are effective spans. The width of the support is 300 mm
along lines 412)
‘
IP hod3 417189
SECTION -C
(a) Derive the expression of determining the development
length of a single bar in tension, State the changes, if any,
for the compression bars. (6)
(b) Define nominal shear stress 1, of rectangular and T-
beams of (i) uniform depth and (ii) varying depth subjected
to bending moment and shear force. (8)
For a ring beam 350 mm wide and 750 mm deep to the bottom,
and 700 mm to the centre of tensile steel, determine the
reinforcement required when subjected to factored moment Mu
= 300 kNm, factored torsion, Tu = 90 kNm and factored shear
Vu = 100 KN. Use M 20 and Fe 415 for the design. (12)
SECTION - D
Design a waist slab type dog legged staircase for an office
building using the following data. Height between floors is 3.2m.
Tread = 270 mm and riser =160 mm. Width of flight = landing
width =1.25 m. The stairs are supported on 300 mm load
bearing masonry walls. at the outer edges of the landing, parallel
to the risers. Use M20 grade of concrete and Fe 415 grade of
steel. (12)
Using Limit State Philosophy, design the reinforcement for a
column 600mm x 600 mm and 12 m long to support a load of
3000 kN and moments of 100 KN-m and 75 kN-m at top along
X and Y directions and moment of 85 KN-m and 60 KN-m at
bottom of the column. Use M25 grade of concrete and Fe 415
grade of steel. (12)
SECTION - E
(a) Name the sample tests to be performed for checking the
strength of concrete.
(b) Differentiate between one-way and two-way slabs.
ct(c)
(d)
(e)
(f)
(g)
(h)
G)
4 17189
Which equation is needed to determine the depth of the
neutral axis?
When do we go for doubly reinforced beams?
Define “effective width” of flanged beams.
How do we design the shear reinforcement close to the
support of a beam?
Explain the situations when do you provide side face
reinforcement in beam.
Explain braced and unbraced columns.
How do you consider effect of spirals in load carrying
capacity of a column?
What are rules from proportioning the tread and rise in a
staircase? (10%1.2=12)