Wiev. —D
[Total No, of Questions - 9} {Total No. of Printed Pages - 4]
(2127)
17190(N)
B. Tech Sth Semester Examination
Structural Analysis-li (CBS)
CE-502
Time : 3 Hours www.epaper-tk Max. Marks : 60
The candidates shall limit their answers precisely within the answer-book
(40 pages) issued to them and no supplementary/continuation sheet will
be issued.
Note : Attempt five questions in all, selecting at least one from each unit,
question no. 9 is compulsory. Assume missing data suitably, if
any.
UNIT -1
1, (a) Find the vertical deflection of A of the structure as shown in
Fig. 1 by using Castigliano’s theorem. All the members have
same sectional area. (6)
Fig. 1
(6) A portal frame ABCD has its end A hinged while end D is on
roller. All the member have same flexural rigidity El and same
length /. A horizontal force applied at the roller end. Find the
horizontal displacement of the roller end by using strain energy
method. (6)
2 (a) Draw ILD for the forces in members P, Q, R and S of the truss
shown in Fig. 2. (8)
Ge(b) Four equal loads of 150 kN each equally spaced at 2 m apart
followed by a ud! of 60 KN/m at a distance of 1.5 m from the
last 150 KN load cross a girder of 20 m span from right to left.
Using influence lines, calculate the shear force at a section 8
m from the left hand support when the leading 150 KN load is
at 5 m from the left hand support (4)
UNIT - II
Analyse the continuous beam shown in Fig. 3 using slope deflection
method and draw BMD. (12)
KN 410kN
Fig. 3
Analyse the frame shown in Fig. 4 by Moment distribution method
and draw SFD and BMD. (12)
SOkN
Fig. 4
IP.T.045.
6.
(a)
(b)
(a)
(b)
$ 47190
UNIT -
In @ multi storey building frame shown in fig are spaced at 4m
intervals. Dead load from the slab is 3 KN/m? and Live load is 5
kNim2. Analyse the beams as shown in Fig. § where self-weight
of the beams may be ignored. Use two-cycle method. (8)
sm
A 8 G
Fig. 5
4m
6m 6m
_ ches
Using the portal method determine the column shear and
moments of the frame as shown in Fig. 6. (4)
20 KN D
€
Fig. 6
e
rere
What are the different types of substitute frame? (4)
Analyse the portal frame shown in Fig. 7 by the portal methoe
and sketch B.M. diagram. (8)
20 kaw 8B c
am
Gem 6m Fig. 77
(a)
(b)
4 17190
UNIT - 1V
Using Flexibility matrix method find the end moment at A and B
for a fixed beam carrying a udi of 4KN/m throughout. (4)
Develop the flexibility and stiffness matrices for the prismatic
member AB for the following support conditions and suurdinates
as shown in Fig. 8.
(i) hinged support at A and roller support at B.
(ii) fixed support at A and B.
(iii) fixed support at A and roller support at B. (8)
@
Tas,
7p
a Bi
A .
am Fig. 8
[ee
EI Constant
8. Analyse and plot BMD for the portal frame as shown in Fig. 9 using
flexibility method. (12)
9.
30 kN/m
50 KN B +
ce 2m
oD
alm Da te
dt A Fig. 9
7AZ_4m
&/ Constant
UNIT - V (Compulsory Question)
Explain the following briefly:
(a)
(b)
(c)
(d)
(e)
(f)
What do you understand by the term redundant trame% How will
you find out the degree of redundancy of a frame’
Describe in brief the significance of influence line diagram.
Explain reason behind sway in frames.
Explain various assumption made in the portal method of
analysis.
Differentiate between Global axis and Focal axis
Differentiate between compatibility and equilibriurn meinod
a bey