Professional Documents
Culture Documents
CrutchfieldMasterSheet 0000190139 PDF
CrutchfieldMasterSheet 0000190139 PDF
Revision 04/26/16
2004-'08
Ford F150
2006-'08
Lincoln Mark LT
IMPORTANT
Before starting, compare items on your invoice with items received.
Carefully check through packaging material. If any item is missing,
*0000190139*
please call Crutchfield Technical Support at 1-800-955-9094.
Although reasonable attempts are made to verify the accuracy of the information contained in this MasterSheet, it is presented without
warranties or guarantees of any type due to the constantly changing nature of this type of information and running changes in vehicle
Inside... production. Any person or entity using this information does so at his or its own risk. If you find our instructions are different from your
vehicle, or if you have questions, do not continue with your installation. Contact our toll-free technical support for assistance.
Page
4 Receiver Installation
5 Front Door Speakers
6 Rear Door Speakers
(Standard
Cab)
7-8 Rear Door Speakers (Super Cab)
9-10 Rear Door Speakers (Supercrew)
11 Rear Subwoofer (Supercrew)
5.5mm 6mm 7mm 8mm 10mm 1/4” 7/32” Panel Tool T20 Torx Driver
Tools Required
3. Pry out around all edges of receiver trimpanel to release retaining clips.
Pull away trimpanel and disconnect airbag harness at top of panel. Set
panel aside (Figures 1-3).
Receiver Trimpanel
4. Remove four (4) 7mm screws securing factory radio. Pull out radio,
disconnect and remove (Figure 4).
FIGURE 3
FIGURE 4
Factory Radio
1-800-955-9094
TECHNICAL SUPPORT Copyright 2016 Crutchfield Corporation 2
019 0139
OEM Integration
R
This page addresses integrating aftermarket accessories such as CD Changers, Auxiliary Input Adaptors, iPod Adaptors, etc.,
with a factory radio system.
Before proceeding, check the manual of the OEM integration device. The device may connect at another location, making radio
removal unnecessary. If the device connects at the rear of the radio, continue with the following steps.
4. IMPORTANT: Reconnect all wiring harnesses including airbag, then reconnect battery. Test operation of the adaptor and
reassemble dash by reversing disassembly steps.
Input
Receiver Assembly
1-800-955-9094
TECHNICAL SUPPORT
FIGURE 1
1-800-955-9094
TECHNICAL SUPPORT Copyright 2016 Crutchfield Corporation 5
019 0139 NOTES:
Please read first
Rear Door Speakers -- Standard Cab • Instructions show factory size speakers or speakers
with adaptor brackets only. Cutting or fabrication (not
shown) will be required for other speaker sizes.
1. Remove one (1) 1/4” screw from bottom of door panel (Figure 1).
2. Pry around all edges of door panel to release clips. Remove panel FIGURE 2 FIGURE 3
(Figure 2).
3. Remove four (4) 1/4” screws securing speaker. Pull out speaker,
disconnect and remove (Figure 3).
FIGURE 1
1-800-955-9094
TECHNICAL SUPPORT
FIGURE 3 FIGURE 4
Screw Cover
FIGURE 5 FIGURE 6
1-800-955-9094
TECHNICAL SUPPORT Copyright 2016 Crutchfield Corporation 7
019 0139
! SAFETY CHECK
Check that wires do not interfere with window operation.
Test door lock and release operation.
1-800-955-9094
TECHNICAL SUPPORT
FIGURE 10
Copyright 2016 Crutchfield Corporation 8
019 0139 NOTES:
Please read first
Rear Door Speakers -- Supercrew • Instructions show factory size speakers or speakers
with adaptor brackets only. Cutting or fabrication (not
shown) will be required for other speaker sizes.
1-800-955-9094
TECHNICAL SUPPORT Copyright 2016 Crutchfield Corporation 9
019 0139
FIGURE 8
! SAFETY CHECK
1-800-955-9094 Check that wires do not interfere with window operation.
Test door lock and release operation.
TECHNICAL SUPPORT Copyright 2016 Crutchfield Corporation 10
019 0139 NOTES:
Please read first
Rear Subwoofer -- Supercrew • Instructions show factory size speakers or speakers
with adaptor brackets only. Cutting or fabrication (not
shown) will be required for other speaker sizes.
1-800-955-9094
TECHNICAL SUPPORT
Wire Splicing Guide These methods can be used to make wiring connections if no receiver or speaker wiring adaptor is available.
Wire color information (if available) can be found on the next page.
Factory harness is removed. Save New speaker wires are spliced into
CRIMP METHOD harness if it is to be reconnected in
the future by this method.
SOLDER METHOD factory wires behind harness.
1. Cut factory wires behind 2. Strip end of each 1. Carefully strip out a 1/2” 2. Twist wires from new
factory speaker harness. wire back 1/2”. section on each factory speaker to stripped
speaker wire behind the sections of factory wires
factory speaker harness. as shown making sure
polarity is correct.
Factory Wires
---
-- - ------
Negative Wires
Strip Out 1/2” New Wires
+
+
+ + + + + + + + + + + + +
Positive Wires
3. Twist each positive pair of 4. Squeeze middle of cap 3. Heat wires first with 4. Wrap wiring connections
wires together and insert for tight connection. soldering iron, then with electrical tape.
in crimp cap. Repeat touch solder to
step for negative wires. 5. Connect new wires to wires for solid 5. Connect new wires to
speaker with spade connections. speaker with spade
First
connectors. connectors.
Factory Wire ---
-- - --------
Last
+
+
+ + + + + + + + + + + + + + + + + + + + +
1-800-955-9094
TECHNICAL SUPPORT Copyright 2017 Crutchfield Corporation 12
019 0139
Wire Splicing Guide NOTE: In most cases a speaker wiring adaptor is available from Crutchfield and splicing will
not be necessary. If no adaptor is available, use this chart as a guide to match and splice wires.
1-800-955-9094
TECHNICAL SUPPORT Copyright 2017 Crutchfield Corporation 13