Professional Documents
Culture Documents
ebf 8251 спецификация на распредвалы 3116-С7
ebf 8251 спецификация на распредвалы 3116-С7
ebf 8251 спецификация на распредвалы 3116-С7
SEBF82510001
ILLAR®
INE FOR
BLE PARTS
LVAGE OPERATIONS
ions for Measurements of
s in 3114, 3116 & 3126/C7
Summary of Revisions
Page Description
Introduction
This guideline enables dealers and their customers to benefit from cost reductions made possible
through an established parts reusability and salvage program. Every effort has been made to provide
the most current and relevant information known to Caterpillar Inc. Since the Company makes
ongoing changes and improvements to its products, this guideline should be used in conjunction
with the latest technical information available from Caterpillar to ensure such changes and
improvements are incorporated where applicable.
For questions or additional information concerning this guideline, contact Caterpillar Service
Development Division, Service Support (309) 675-5434.
Summary
The information given in this guideline can be used to determine if a camshaft can be reused. A
camshaft that meets the specifications found in this guideline and other applicable guidelines can be
expected to give normal performance until the next overhaul, when used again in the same
application.
A used or reground camshaft must be measured for bearing journal wear, lobe wear, straightness,
and surface finish.
Use two 5P-8637 Support Groups or similar V-block supports on a flat surface to hold the camshaft
during the measuring procedures.
References
References
Media Title
Number
Required Tools
Part Part Description
Number
1
Refer to SEBF8097 "Camshaft Measurement" for a list of surface finish analyzers.
Chart A.
65.084 65.072 39.2 39.2 41.2 8.78 8.78 9.23 0.8 0.45
7C-4014
(2.56) (2.56) (1.57) (1.57) (1.65) (0.346) (0.346) (0.363) (0.032) (0.017)
65.084 65.072 39.2 39.2 41.2 8.76 6.96 9.23 0.5 0.45
115-4131
(2.56) (2.56) (1.57) (1.57) (1.65) (0.345) (0.274) (0.363) (0.020) (0.017)
65.084 65.072 39.2 39.2 41.2 8.78 8.78 9.23 0.5 0.45
7C-4016
(2.56) (2.56) (1.57) (1.57) (1.65) (0.346) (0.346) (0.363) (0.020) (0.017)
65.084 65.072 43.2 43.2 42.7 8.76 6.96 9.8 0.5 0.45
100-6300
(2.56) (2.56) (1.7) (1.7) (1.68) (0.345) (0.274) (0.386) (0.020) (0.017)
65.084 65.072 39.2 39.2 41.2 8.78 8.445 9.23 0.5 0.45
7E-5400
(2.56) (2.56) (1.57) (1.57) (1.65) (0.346) (0.332) (0.363) (0.020) (0.017)
65.084 65.072 39.2 43.2 43.7 8.78 6.96 9.23 0.5 0.45
6I-4098
(2.56) (2.56) (1.57) (1.7) (1.72) (0.346) (0.274) (0.363) (0.020) (0.017)
65.084 65.072 39.2 39.2 41.2 8.78 6.71 9.23 0.5 0.45
101-4512
(2.56) (2.56) (1.57) (1.57) (1.65) (0.346) (0.264) (0.363) (0.020) (0.017)
65.084 65.072 39.2 39.2 41.2 8.78 8.78 9.23 0.5 0.45
9Y-8295
(2.56) (2.56) (1.57) (1.57) (1.65) (0.346) (0.346) (0.363) (0.020) (0.017)
65.084 65.072 39.2 39.2 41.2 8.78 8.78 9.23 0.5 0.45
4P-0266
(2.56) (2.56) (1.57) (1.57) (1.65) (0.346) (0.346) (0.363) (0.020) (0.017)
65.084 65.072 39.2 39.2 41.2 8.78 8.35 9.23 0.5 0.45
7E-5399
(2.56) (2.56) (1.57) (1.57) (1.65) (0.346) (0.329) (0.363) (0.020) (0.017)
65.084 65.072 43.2 43.2 41.2 8.76 6.96 9.23 0.5 0.45
133-4984
(2.56) (2.56) (1.7) (1.7) (1.65) (0.345) (0.274) (0.363) (0.020) (0.017)
65.084 65.072 43.2 43.2 42.7 8.76 6.96 9.8 0.5 0.45
107-7603
(2.56) (2.56) (1.7) (1.7) (1.68) (0.345) (0.274) (0.386) (0.020) (0.017)
65.084 65.072 43.2 43.2 42.7 8.76 6.96 9.8 0.5 0.45
105-1560
(2.56) (2.56) (1.7) (1.7) (1.68) (0.345) (0.274) (0.386) (0.020) (0.017)
65.084 65.072 43.2 43.2 42.7 8.78 6.96 9.8 0.5 0.45
167-3811
(2.56) (2.56) (1.7) (1.7) (1.68) (0.346) (0.274) (0.386) (0.020) (0.017)
© 2004 Caterpillar
All Rights Reserved Printed in the U.S.A
Copyright 1993, 2004 Caterpillar Inc. Mon Oct 18 18:50:30 UTC+0400 2004
All Rights Reserved.
Private Network For SIS Licensees.