Professional Documents
Culture Documents
Common Precautions For Connectors
Common Precautions For Connectors
Common Precautions For Connectors
1
Common Precautions for Connectors
■ Mechanical matters
● Connecting and disconnecting connectors ● Fixing connectors to boards
• Keep connectors horizontal or vertical, when connecting and • Riveting connectors to boards can damage the housing,
disconnecting. therefore check pins or screws are recommended to fix
Twisting the connector can result in damage or faulty contact. connectors to boards.
• Insert connectors fully to sockets when connecting. • Tightening screws with excessive torque can cause faulty
• The number of connections/disconnections is specific to contact, faulty mating, etc., therefore control tightening to the
speed. specified torque.
If inserted or removed at a very fast speed, the connector is
● Wiring
subjected to shock that can affect performance.
• If the customer wants to wire connectors after they have been
Moreover, durability depends on handling even when within
fitted with wires, do not apply the normal load to wires when
speed and frequency tolerances, therefore test connectors in
wiring.
advance.
• Do not hold the connector by the wires when disconnecting. ● Use of check pins
Actions of the sort can disconnect or break wires. • In general, check pins serve to temporarily anchor connectors
● After connecting wires to boards before mounting and to ensure sufficient strength
after mounting.
• Do not pull on connected wires with more than the necessary
• Check pins are generally mounted on boards all at the same
force.
time, but retaining strength is not guaranteed if used only to
Pulling with excessive force can damage connectors, or
immobilize the board or used without mounting.
disconnect or break wires.
● Processing dimensions for printed circuit boards
■ Installation matters • Strictly adhere to printed circuit board processing dimensions
● Soldering conditions when designing boards. Improper dimensions can result in
• The recommended soldering conditions differ according to faulty connections when mounting connectors on boards and
product, therefore refer to "Safety Precautions" of the specific faulty mating after mounting.
product for details.
Contact your dealer about soldering under unrecommended ■ Working environment, storage environment
conditions. and disposal
● Coating flux ● Operating temperature range
• Note that flux can wick up to contacts because of capillary • The operating temperature adds the temperature rise
effect depending on the amount of flux coated. component when power is on to the Ambient operating
Special processing is available to prevent flux wicking with temperature.
products, therefore contact your OMRON sales representative Ambient operating temperature + Temperature rise = Operating temperature
for details. Therefore, show consideration so that the operating
Note: Do not brush on flux from the underside of the board, as this can result in temperature does not exceed the maximum of the ambient
an increased amount of flux and subsequently flux wicking. operating temperature and the temperature rise component
● Use of multiple connectors when power is on.
• When daisy-chaining multiple boards, mating issues can occur ● Storage
because of connector pitch slip. • Store connectors where not exposed to dust and humidity.
Show adequate consideration for the accuracy between board Also, keep connectors away from sources of ammonia gas,
patterns, etc. sulfidizing gases, etc.
● Immobilizing boards for connector mating ● Disposal
• If boards are immobilized solely by connectors, cracking can • Dispose of connectors as industrial waste. Do not dispose of
occur in solder bonds because of stress. Use screws, spacers connectors as general waste. Also, do not bury, dump in rivers
or other means to immobilize boards without loading or sea areas, or otherwise dispose of connectors in ways that
connectors. pollute the environment.
• Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product.
• Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad
systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious
influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or
equipment, and be sure to provide the system or equipment with double safety mechanisms.
OMRON Corporation
ELECTRONIC AND MECHANICAL COMPONENTS COMPANY Contact: www.omron.com/ecb Cat. No. G069-E1-01
0412(0412)(O)