Professional Documents
Culture Documents
Weberfix PU - Datasheet
Weberfix PU - Datasheet
Weberfix PU - Datasheet
Suitable for all surfaces like metal, plywood, drywall, AAC wall panels,
PU waterproofed surface, tile-on-tile & tile-on-stone, lime mortar surface
and cementitious plasters
deformation due to water absorption and wood, MDF, MR grade plywood, chipboard.
thermal expansion. • Tile substrates like ceramic tile, vitrified tile,
• Suitable to install all tiles and stones including stone, porcelain tiles, glazed tiles, vinyl tiles.
glass** and metal tiles. • Waterproofing substrates like mastic asphalt,
• Weberfix PU can be used for new construc- cementitious, epoxy, polyurethrane.
tion as well as for renovation over existing • Other substrates like brick Masonry, gypsum
plaster, underfloor heating installation, over- Note:
laid timber floors, metal, rubber, linoleum, • In case of higher undulation, a neat coat of
PVC. SBR LitX to be applied on the substrate,
Note: Refer to the backer board manufacturer's followed by application of weberwall
data sheet for specific board intended for use. premium plaster, to smoothen the surface
(Refer technical data sheet of Weber SBR LitX
Application areas and weberwall premium plaster for further
details).
Suitable for interior as well as exterior, wall &
• In case of oil stains, use of surfactants may be
floor.
necessary, followed by proper cleaning with
water, to avoid debonding of tiles.
Surface preparation • Leave expansion joints of atleast 10mm thick-
For Cementitious substrate, waterproofing and ness, for every 12 feet in the substrate and in
tiles: accordance with industry standards. Do not
• Substrate should be structurally sound, clean cover expansion joints with adhesive, and can
and free of all bond inhibiting compounds, like be filled with appropriate flexible sealant.
dirt, oil, grease, paint, sealers, curing
compounds, laitance etc. Remove dirt, dust Mixing
and laitance if any using high pressure water • Take 9 parts component A, and 1 part compo-
jet or any other suitable method. Surfactants nent B, by weight (5:1 by volume) in a bucket /
may be required for oil, grease etc. other suitable container.
• Surfaces should be within 15°C to 40°C (at • Mix for 3-5 minutes, preferably using a slow
higher temperature material will set faster. To speed stirrer (100 rpm), or using any other
bring down the temperature, saturate with suitable method. Mixing at high speed should
water). be avoided.
• Rough or uneven concrete surfaces should be • Mix only the quantity of adhesive, which can
made smooth. Concrete screeds, renders and be consumed in 90 mins.
block work should be sufficiently cured to • Wash tool immediately with water, after use,
avoid shrinkage cracks. and before the adhesive hardens.
• Saturate the surface well (cementitious • No water to be added to the mix.
substrates) and remove excess water before
application of the tile adhesive. Surface
Application
should be brought to touch dry condition.
• Apply the adhesive onto the substrate cover-
For Drywalls and other substrates: ing up to 1 m2 at a time (or no more than what
• Only dry cleaning is recommended for such can be tiled within 30 minutes). Unfavorable
substrates.. For metallic substrate, loose rust weather conditions (strong sun, dry wind,
weberfix PU
and paint needs to be removed and to be high temperature etc.) or a highly absorbent
properly treated before application of substrate can reduce the open time, even to
Weberfix PU. Use a wire brush if required, to just a few minutes. It is therefore necessary
remove any bond inhibiting compound. that careful checks be made to ensure that
• Ensure that the substrate is flat, stable and adhesive fins do not become hard. If observed
well adhered. hard, remove the adhesive, and apply fresh
adhesive. after fixing, to verify that the required contact
• Apply Weberfix PU over the surface using the is being achieved.
straight edge of the notched trowel and then • In wet areas, external areas and all floors, the
comb the applied adhesive using the notched final adhesive bed should be free from voids.
side of the trowel to achieve the desired • If necessary, tiles should be adjusted, within
thickness. 90 minutes of installation.
• Double buttering is recommended for heavier • Carefully clean off any excess adhesive from
stones. the tiles and joints with a damp sponge or
• If the adhesive is buttered to the tile, then cloth before it sets. Leave for at least 24 hours
ensure proper coverage of the tile surface to before grouting.
prevent void formation. • More time may be required before grouting
• Leave expansion joints of atleast 10mm when tiling onto impervious or sealed surfac-
thickness, for every 12 feet in the substrate es or higher bed thickness.
and in accordance with industry standards.
• Do not cover expansion joints with adhesive, Note to specifier and installer
and can be filled with appropriate flexible • Do not use on wet screed or plaster.
sealant. • Surface must be fully cured.
• Joint width shall be as per recommendation • No primer is required, for fixing even heavier
of architect/site engineer. stones on drywall or plywood.
NOTE: The size of the notch trowel and the angle • To prevent any discoloration of highly porous
of application will determine the bed thickness natural stone, treat with under-tile impregna-
as per the following formula: tor webersys stoneprotect.
• To get excellent stain resistance on stone, use
Bed Thickness = NW × NH × sin θ
hydrophobic and oliophobic impregnator
(NG+NW)
webersys stoneseal.
Where:
• To get invisible joints between spaced tile and
• NW is the width of the notch.
stones, fill with specially formulated weber
• NG is the gap in between the notches.
pearl armor specialty grout.
• NH is the height of the notch.
• To get high aesthetic appeal, fill joints with
• θ is the angle of application.
weber knight armor specialty grout.
Please use small sample for application evalua-
• When highly porous natural stone is treated
tion in case of pure white or highly porous stones
with webersys stoneseal as an impregnator
before going for large scale usage.
to prevent capillary movement of slurry to
avoid patches on top of stone, needs to be
Installing the tile fixed with weberfix PU.
• Clean the stone/tile with water/ dry cloth
before installation.Wipe with a clean dry cloth, Grouting
weberfix PU
Technical parameters
Shelf Life
Physical Color Off white
1 year from month and year of manufacturing,
Resin Paste form
for unopened buckets and can, stored in dry
Hardener Liquid form
condition.
Chemistry PU blend with epoxy
reaction resin adhesive
Substrate Cementitious, RCC, Storage
plywood, tile on tile, Store in a cool and dry place
drywall, metal, PVC,
rubber, linoleum, epoxy
waterproof, PU waterpro- Disclaimer
ofed surface, Bitumen
The user should determine the usability of the
surface
product for its intended use. Our products are
Tiles Ceramic, vitrified, glass
mosaic, impregnated manufactured under the Saint-Gobain quality
stone, engineered stone, standards, and subjected to strict quality control
natural stone, glass tile, procedures. Since the company has no control
mirror over site conditions and installation procedures,
Application No spacer required if the company will not be responsible under any
adequate construction
joints are provided as circumstances for any loss, damage or liability
per industry standards from incorrect usage.
Open time and pot life
larger format tile & stone
weberfix PU
PU Coated Glass
Wooden flooring
Ceramic mosaic
Precast terazzo
Artificial Stone
Marble Mosaic
Porcelain Tiles
Glass Mosaics
Natural Stone
Ceramic tiles
Vitrified tiles
Quarry tile
Metal Tiles
Terracotta
Pavers
TILES
Brick
SUBSTRATES
Cement-based screeds and mortars
cement-based plasters/renders
Existing floor
Cementitious Concrete Masonry
Cement Terrazzo
Blocks
Self Levelling Screeds
Gypsum board
Calcium Silicate board
Bison Panel Board
Plaster board
Tile backer board
Drywall Fibre Cement board
Cement Backer board
Engineered Wood
MDF
MR grade Plywood
Chipboard
Brick Masonry
Gypsum plaster
Others Underfloor Heating installation
Overlaid Timber Floors
PVC
Ceramic tile
Vitrified tile
weberfix PU
Tiles
Stone
Vinyl tiles
Mastic Asphalt
Cementitious
Waterproof-
Epoxy
ing
Polyurethrane
* construction joints shall be built as per industrial standards
** not for PU coated glass
Technical standards and performance ISO 13007 & EN 12004
Classification Property Requirement weberfix PU
R2 – Improved adhesives Shear adhesion strength > = 2 N/mm2 > 2.2 N/mm2
(additional characteristics) after thermal shock
T – Slip resistance Vertical slip resistance < = 0.5 mm No slip
https://goo.gl/d39avs
Product information
/SaintGobainWeberIndia /company/saint-gobain-weber-india
www.in.weber