Professional Documents
Culture Documents
Astm F 436 - 11
Astm F 436 - 11
Astm F 436 - 11
--`,,```,,,,````-`-`,,`,,`,`,,`---
7.3 Unless otherwise stated in the inquiry or purchase order,
plain (uncoated) hardened steel circular washers shall be tests and inspections shall be made at the place of manufacture,
furnished. Where corrosion-preventive treatment is required, unless otherwise agreed to.
washers shall be coated as agreed upon between the manufac- 11.2 If other than the normal inspection for continuous mass
turer and the purchaser. production of parts as stipulated in 9.1 is required by the
purchaser, it shall be specified in the inquiry and contract order.
8. Workmanship, Finish, and Appearance
8.1 Washers shall be free of excess mill scale, excess 12. Rejection and Rehearing
coatings and foreign material on bearing surfaces. Arc and gas 12.1 Disposition of nonconforming washers shall be in
cut washers shall be free of metal spatter. accordance with Guide F1470 section titled “Disposition of
Nonconforming Lots.”
9. Sampling and Number of Tests
9.1 The requirements of this specification shall be met in 13. Certification and Test Report
continuous mass production for stock, and the manufacturer 13.1 Upon request of the purchaser in the contract or order,
shall make sample inspections to ensure that the product a manufacturer’s certification that the material was manufac-
conforms to the specified requirements. Additional tests of tured and tested in accordance with this specification, together
individual shipments of material are not ordinarily contem- with a report of the latest mechanical tests of each stock size in
plated. each shipment, shall be furnished at the time of shipment.
9.2 When weathering steels are furnished to Corrosion 13.2 Data contained in the certified test report shall include
Resistance Index, the CRI number shall be calculated for each material grade, hardness tests, and calculated Corrosion Resis-
heat. tance Index when type 3 is furnished to a Corrosion Resistance
9.3 When additional tests are specified in the inquiry or Index.
purchase order, a lot, for purposes of selecting test samples,
shall consist of all material offered for inspection at one time 14. Responsibility
that has the following common characteristics: 14.1 The party responsible for the fastener shall be the
9.3.1 Same nominal size. organization that supplies the fastener to the purchaser.
9.3.2 Same raw material heat number.
9.3.3 Same nominal post treatment (heat treatment or coat- 15. Product Marking
ing or both). 15.1 Washers shall be marked with a symbol, or other
9.4 From each lot described in 9.3, the number of specimens distinguishing marks, to identify the manufacturer or private
tested for each required property shall be as follows: label distributor, as appropriate.
14
⁄ 0.625 0.281 0.051 0.080 ... ... 0.219
5 16
⁄ 0.688 0.344 0.051 0.080 ... ... 0.281
3⁄ 8 0.813 0.406 0.051 0.080 ... ... 0.344
4
7⁄16 0.922 0.469 0.051 0.080 ... ... 0.406
1⁄ 2 1.063 0.531 0.097 0.177 0.305 0.375 0.438
9⁄16 1.188 0.625 0.110 0.177 0.305 0.375 0.500
⁄
12 1 3 ⁄4 ⁄
17 32 ⁄
5 16 1:6 ⁄
7 16
⁄
58 1 3 ⁄4 ⁄
11 16 ⁄
5 16 1:6 ⁄
9 16
1 1⁄ 8 2 1 ⁄4 1 1⁄ 4 5⁄16 1:6 1
1 1⁄ 4 2 1 ⁄4 1 3⁄ 8 5⁄16 1:6 13⁄32
1 3⁄ 8 2 1 ⁄4 1 1⁄ 2 5⁄16 1:6 17⁄32
1 1⁄ 2 2 1 ⁄4 1 5⁄ 8 5⁄16 1:6 15⁄16
A
Rectangular beveled washers shall conform to the dimensions shown above, except that one side may be longer than that shown for the A dimension.
B
Clipped edge E shall not be closer than 7⁄8 of the bolt diameter from the center of the washer.
15.2 Additionally, Type 3 weathering steel washers shall be 16.1.1 Unless otherwise specified, packaging shall be in
--`,,```,,,,````-`-`,,`,,`,`,,`---
S1. Surface Roughness S1.2 Burrs shall not exceed 0.01 in. in height.
S1.1 Washers shall have a multidirectional lay with a
surface roughness not exceeding 750 µin. in height including
any flaws in or on the surface.
SUMMARY OF CHANGES
Committee F16 has identified the location of selected changes to this standard since the last issue (F436–10)
that may impact the use of this standard. (Approved May 15, 2011.)
Committee F16 has identified the location of selected changes to this standard since the last issue (F436–09)
that may impact the use of this standard. (Approved May 1, 2010.)
(1) In 5.2 – 5.4, 9.2, 10.3.1 and 13.2 provided for furnishing (2) Revised 12 Rejection and Rehearing to invoke Guide
Type 3 to a corrosion Resistance Index of 6 or higher. F1470.
Committee F16 has identified the location of selected changes to this standard since the last issue (F436–07)
that may impact the use of this standard. (Approved Jan. 1, 2009.)
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/
COPYRIGHT/).
--`,,```,,,,````-`-`,,`,,`,`,,`---