Professional Documents
Culture Documents
Paramteres Comparison (Huawei&Ericsson)
Paramteres Comparison (Huawei&Ericsson)
Paramteres Comparison (Huawei&Ericsson)
qHyst1 IDLEQHYST1S
qHyst2 IDLEQHYST2S Cell Reselection Parameters
qOffset1sn IDLEOFFSET1SN
qOffset2sn IDLEQOFFSET2SN
sIntraSearch IDLESINTRASEARCH
Criteria to start measurements on an Intra frequency, inter frequency, or IRAT cell to
sInterSearch IDLESINTERSEARCH
perform cell reselection
sRATSearch SSEARCHRAT
CONNSINTRASEARCH
cnDRXCycleLengthCs/cnDRXCycleLen
DRXCYCLELENCOEF Used by UE in IDLE Mode
gthPs
* PICHMODE Indicate # of PI's in a PICH frame
* MACCPAGEREPEAT # of retransmissions of Paging messages
Max Time for UE to wait after tx RRC connenction Request until RRC Connection setup is
T300
received
N300 number of retx of RRC connection request
T312 timer for UE to wait for L1 Synch (after receiving N312 synch msg)
N312
RRCCAUSE
SIGCHTYPE channel type for RRC establishment
NOT_SUPPORT indicates that the Intrafreq measurement control message will be send in
INTRAMEASCTRL RRC Connection Establishment. SUPPORT indicates that the Intrafreq measurement control
will not be send in RRC Connection Establishment.
POWER CONTROL PARAMETERS
constantValueCprach CONSTANTVALUE Constant power value sent by RBS and used for open loop power control in UL
tp-p time interval between 2 preambles
tppmin min time interval //
tp-a time interval between PRACH preamble and AICH
tp-m time interval between last preamble and the PRACH message part
AICHTXTIMING is=1 or 0. Determine the value of tp-pmin, tp-a, and tp-m
powerOffsetPpm POWEROFFSETPPM change of power between the successful preamble power and the control part of the initial
RACH msg
preambleRetransMax PREAMBLERETRANSMAX maximum retransmissions of preambles in 1 cycle
maxPreambleCycle MMAX max cycles
NB01MIN/NB01MAX upper and lower limit for backoff time after failing cycle
BetaPrachControlTF0 betac
Gain Factor between control part and data part (for RACH carrying CCCH and DCCH)
BetaPrachDataTF0 betad
BetaPrachControlTF1
Gain Factor between control part and data part (for RACH carrying DTCH)
BetaPrachDataTF1
MAXULTXPOWERFORCONV
MAXULTXPOWERFORSTR
Upper limits for power in UL according to the service class
MAXULTXPOWERFORINT
MAXULTXPOWERFORBAC
Betac Betac
Gain factors for DPDCH over DPCCH
Betad Betad
RLMAXDLPWR
Max and Min for DPDCH in DL
RLMINDLPWR
In huawei we have 2 algorithms for Inner Loop power control, 1 fast at rate 1500
PWRCTRLAG
update/sec, and the second is slower at rate 300 update/sec. these are PLA1 and PCA2
this is the step of increasing or decreasing the power in inner loop PC. In ericsson this will
ULTPCSTEPSIZE
be fixed for 1 db, and could change if using compressed mode.
DPCMODE there are 2 modes: either send 1 TPC per slot (mode 0) or send 1 TPC each 3 slots (mode 1).
INNER_LOOP_DL_LMTED_PWR_INC_S When it is checked, limited power increase algorithm is applied in the inner loop power
WITCH control. limited power increase algorithm means that when the DL transmit power is
POWERRAISELIMIT increased, there is a limit for the step, that is, each increase is limited.
DLPOWERAVERAGEWINDOWSIZE window size in slots, which is the time during which the increase in power is limited
FDDTPCSTEPSIZE
DOWNLINK_POWER_BALANCE_SWITC
switch power balance on (always on in E///)
H
DPBSTARTTHD/DPBSTOPTHD start and stop thresholds for power balance
ulOuterLoopRegulator Determine if using step regulator or jump regulator in UL Outer loop power control
HANDOVER PRAMETERS
Soft handover:
IntraFreqMeasQuantity These are to determin whether measurement is done over RSCP or Ecno
interFreqMeasQuantity I guess in ericsson these are the same, and these are transmitted in the measurement
MeasQuantityOf3A control message during the rrc establishment or after a HO process is done
filterCoefficient1 FilterCoef
filterCoefficient2 interFreqFilterCoef coefficients for L3 filters to filter the measurements
utranFilterCoefficient3 interRatFilterCoef
reportingRange1a INTRARELTHDFOR1ACS
INTRARELTHDFOR1APS
hysterisis1a HYSTFOR1A
timeToTrigger1a TRIGTIME1A
individualOffset CELLINDIVIDUALOFFSET
w1a/w1b Weight
* SHOQualmin
reportingRange1b INTRARELTHDFOR1BCS
INTRARELTHDFOR1BPS
hysterisis1b HYSTFOR1B
timeToTrigger1b TRIGTIME1B
maxActiveSet In Huawei, the max active set is 3 the Max value of maxActiveSet is 4, but default value is 3
hysterisis1c HYSTFOR1C
timeToTriggerc TRIGTIME1C
hysterisis1d HYSTFOR1D
timeToTriggerd TRIGTIME1D
Intrafrequency Hard Handover
The bit rate threshold used to determine whether to perform soft handover for the Best
Effort (BE) service on DCH. When the maximum bit rate of the BE service is lower than or
equal to this threshold, the system will perform soft handover for this user to guarantee the
BEBITRATETHD
service quality. If the maximum bit rate of the BE service is higher than the threshold, the
system will perform intrafrequency hard handover for this user to avoid the too great effect
of soft handover on the system capacity
Interfrequency Handover and IRAT Handover
fddGSMHOSupp if RNC supports inter Rat HO
ffdIFHOSupp If RNC supports inter frequency HO
hOType Irat or inter frequency is prioritized
hoOTypeDRNCBand Same as above, but over Iur interface
hysterisis2d HYSTFOR2D
hysterisis2f HYSTFOR2F
hyst4_2b HYSTFOR2B
timeToTrigger2dEcno TRIGTIME2D
timeToTrigger2dRscp
timeToTrigger2fdEcno TRIGTIME2F
timeToTrigger2fdRscp
timeTrigg4_2b TRIGTIME2B
usedFreqThresh2dEcno interFreqCSThd2dEcNo interRATCSThd2dEcNo
interFreqPSThd2dEcNo interRATPSThd2dEcNo
usedFreqThresh2dRscp interFreqCSThd2dRSCP interRATCSThd2dRSCP
interFreqPSThd2dRSCP interRATPSThd2dRSCP
usedFreqThresh2dEcnoDrnc
usedFreqThresh2dRscpDrnc
usedFreqRelThresh2fEcno INTERFREQCSTHD2FEcNO INTERRATCSTHD2FEcNO
INTERFREQPSTHD2FEcNO INTERRATPSTHD2FEcNO
usedFreqRelThresh2fRscp INTERFREQCSTHD2FRSCP INTERRATCSTHD2FRSCP
INTERFREQPSTHD2FRSCP INTERRATPSTHD2FRSCP
utranRelThreshRscp
usedFreqThresh2bEcno IFHOUsedFreqCSThdEcN0
IFHOusedFreqPSThdEcN0
usedFreqThresh2bRscp IFHOUsedFreqCSThdRSCP
IFHOusedFreqPSThdRSCP
nonusedFreqThresh4_2bEcno INTERfREQCOVHOCSTHDECNO the quality of the target should be higher than that threshold
INTERfREQCOVHOPSTHDECNO
nonusedFreqThre4sh_2bRscp INTERfREQCOVHOCSTHDRSCP
INTERfREQCOVHOPSTHDRSCP
ueTxPowerThresh6a
ueTxPowerThresh6b
timeTrigg6a
timeTrig6b
hysterisis3a HYSTFOR3A
timeToTrigger3a TRIGTIME3A
gsmtresh3a
utranRelThresh3aEcno IRHOUSEDFREQCSTHDECNO
IRHOUSEDFREQPSTHDECNO
utranRelThresh3aRscp IRHOUSEDFREQCSTHDRSCP
IRHOUSEDFREQPSTHDRSCP
If the value of [Inter-RAT report mode] is EVENT_TRIGGER, this parameter is used to set the
measurement control on the event 3A. The event 3A is triggered, when the quality of the
INTERRATCOVHOCSTHDECNO
cell with the target frequency is higher than this threshold and the threshold of the used
frequency quality of the corresponding measurement quantity is reached.
INTERRATCOVHOPSTHDECNO
INTERRATCOVHOCSTHDRSCP
INTERRATCOVHOPSTHDRSCP
CELLINDIVIDUALOFFSET also for IRAT HO
interFreqNComHOThdEcNo
Hystfor2C
TrigTime2C
This parameter is used to set measurement control on the event 3C. The event 3C is
Event 3C:
triggered when the quality of the target frequency is higher than this threshold
INTERRATNCOVHOCSTHD
INTERRATNCOVHOPSTHD
Hystfor3C
TrigTime3C
An inter-RAT handover to a GSM cell may fail due to the heavy load of the GSM cell.
PENALTYTIMEFORINTERRATHO Therefore, in the period of time specified by this parameter, inter-RAT handover requests
are not sent to the GSM cell
This parameter specifies the maximum number of attempts for the RNC to perform inter-
INTERRATHOATTEMPTS RAT handovers after a non-coverage-based inter-RAT handover failure. For later handover
attempts, target cells must be selected
After inter-RAT measurement starts, if no inter-RAT handover is performed when this timer
INTERRATMEASTIME expires, the inter-RAT measurement is stopped. In addition, the compressed mode is
deactivated, if any. The value 0 indicates the timer is not to be enabled
the PS streaming service can be mapped onto HS-DSCH when the downlink max bit rate is
PS_STREAMING_ON_HSDPA_SWITCH
more than or equal to DL streaming threshold on HSDPA.
DlStrThsonHsdpa
DlBeTraffThsOnHsdpa
numHsScchCodes HSSCCHCODENUM # of HS_SCCH in a cell
deltaAck1, ACKPO1, ACKPO2, ACKPO3 power offset of ACK(DACK) comparing to uplink DPCCH power in non-soft handover status.
ACKPO1FORSHO, ACKPO2FORSHO,
deltaAck2 power offset of ACK (DACK) comparing to uplink DPCCH power in soft handover status.
ACKPO3FORSHO
deltaNack1 NACKPO1, NACKPO2, NACKPO3
NACKPO1FORSHO, NACKPO2FORSHO,
deltaNack2
NACKPO3FORSHO