Professional Documents
Culture Documents
Umts Parameter Mapping (Huawei - Ericsson-Final
Umts Parameter Mapping (Huawei - Ericsson-Final
Umts Parameter Mapping (Huawei - Ericsson-Final
If Manual is chosen,
parameter " Code Number
for HS-PDSCH " determines
HS-PDSCH code number to
be allocated. If Automatic is
chosen, allocate HS-PDSCH
Allocate Code Mode code number between
Cell AllocCodeMode configured " Code Max
Number for HS-PDSCH " and
" Code Min Number for HS-
PDSCH ". For detailed
information of this
parameter, refer to 3GPP TS
25.308.
Unit: min
A timer to RNC wait for
radio link restoration
indication in the radio link
procedure. Note: The value
range of "RlRstrTmr" is 1 to
300000 in the current
version. In a later version,
the value range changes into
100 to 300000. In the
RL restoration timer current version, if you enter
RNC RlRstrTmr a value within the range of 1
to 100 including 1, this value
can still be synchronized and
issued but the system
regards the value as 11000,
the recommended value.
Therefore, you are advised
not to enter a value smaller
than 100.
MAP_CSPS_PS_UL_USE_DC
H_SWITCH: Whether uplink
PS services of CS and PS
combined services are
carried on DCHs. When this
switch is turned off, the RNC
Whether uplink PS services
MAP_CSPS_PS_UL_USE_DC determines the channel for
RNC H_SWITCH of CS and PS combined carrying uplink services of
services are carried on DCHs
CS and PS combined
services. When this switch is
turned on and CS and PS
combined services existing,
the uplink PS services must
be carried on DCHs.
CPICH RSCP access threshold
of the cell.This parameter is
the minimum required RX
level that corresponds to
CPICH RSCP. The UE can
camp on the cell only when
the measured CPICH RSCP is
greater than the value of
this parameter.
The settings of "Qrxlevmin"
and "Qqualmin" should be
considered along with each
other.
As for the impact on
network performance:
The larger the value of the
parameter is, the more
Cell Qrxlevmin Min RX Level difficult it is for the UE to
camp on the cell. The
smaller the value of the
parameter is, the easier it is
for the UE to camp on the
cell. But if the value is
excessively small, it is
possible that the UE cannot
receive the system
messages carried by
PCCPCH.
When this parameter is not
set to any value, the UE
adopts the corresponding
value of the current serving
cell, added through the ADD
UCELLSELRESEL command.
Generally, this parameter is
reselection between
different cells. Note that the
value 0 corresponds to the
default value defined in the
protocol.
Set the parameter as
follows:
1. Ensure that the UE can
reselect a cell when crossing
the non-soft-switch area of
the cell and that the UE
timely performs location
updates, cell updates, or
URA updates when
necessary.
2. Ensure that the UE does
not reselect a cell when it is
Cell Treselections Reselection delay time in the soft-switch area of the
cell. In this way, the
unnecessary location
updates, cell updates, and
URA updates are avoided.
3. Consider the difference
between cells that cover
different areas, for example
the cells covering highways
and cells covering densely
populated areas. TIf the
parameter is set to a
comparatively low value, the
ping-pong reselections may
be caused. The parameter
can be increased in
populated area and reduced
in high-speed movement. If
The minimum required
quality threshold
corresponding to CPICH
Ec/No. The UE can camp on
the cell only when the
measured CPICH Ec/No is
greater than the value of
this parameter. The higher
the parameter value is, the
more difficult it is for the UE
Cell Qqualmin Min quality level
to reside in the cell. The
lower parameter value is,
the easier it is for the UE to
reside in the cell, but it is
possible that the UE cannot
receive the system
messages that are sent
through the PCCPCH. For
detailed information, refer
to the 3GPP TS 25.304.
Ec/No threshold of
triggering the inter-
frequency measurement for
PS non-HSPA services.
When Ec/No is used as the
measurement quantity for
inter-frequency handovers
Inter-freq R99 PS Measure of PS non-HSPA services, the
Cell InterFreqR99PsThd2DEcN0
Start Ec/No THD UE reports event 2D when
the measured Ec/No value is
lower than the value of this
parameter. Then, the RNC
sends a signaling message to
activate the compression
mode and start the inter-
frequency measurement.
is associated with slow
fading. If this parameter is
set to a greater value, the
probability of incorrect
decision becomes low;
however, the handover
algorithm becomes slow in
responding to signal change.
The emulation result shows
that the hysteresis setting
can effectively reduce the
average number of
handovers and the number
of incorrect handovers, thus
preventing unnecessary
handovers. The emulation
result also shows that the
UE at different data rates
Cell TrigTime2D 2D Event Trigger Delay Time may react differently to the
delay for triggering the
event. For the fast-moving
UE, the call drop rate is
more sensitive to the delay,
whereas, for the slow-
moving UE, the call drop
rate is less sensitive to the
delay. This can also reduce
ping-pong handovers and
incorrect handovers.
Therefore, for the cell where
most UEs are in fast
movement, this parameter
can be set to a smaller
value, whereas for the cell
where most UEs are in slow
movement, this parameter
is associated with slow
fading. If this parameter is
set to a greater value, the
probability of incorrect
decision becomes low;
however, the handover
algorithm becomes slow in
responding to signal change.
The emulation result shows
that the hysteresis setting
can effectively reduce the
average number of
handovers and the number
of incorrect handovers, thus
preventing unnecessary
handovers. The emulation
result also shows that the
UE at different data rates
Cell TrigTime2F 2F Event Trigger Delay Time may react differently to the
delay for triggering the
event. For the fast-moving
UE, the call drop rate is
more sensitive to the delay,
whereas, for the slow-
moving UE, the call drop
rate is less sensitive to the
delay. This can also reduce
ping-pong handovers and
incorrect handovers.
Therefore, for the cell where
most UEs are in fast
movement, this parameter
can be set to a smaller
value, whereas for the cell
where most UEs are in slow
movement, this parameter
algorithm becomes fast in
responding to signal change;
however, the probability of
incorrect decision becomes
high.
The emulation result shows
that the hysteresis setting
can effectively reduce the
average number of
handovers and the number
of incorrect handovers, thus
preventing unnecessary
handovers. The emulation
result also shows that the
UE at different data rates
may react differently to the
delay for triggering the
Cell TrigTime3A 3A Event Trigger Delay Time event. For the fast-moving
UE, the call drop rate is
more sensitive to the delay,
whereas, for the slow-
moving UE, the call drop
rate is less sensitive to the
delay. This can also reduce
ping-pong handovers and
incorrect handovers.
Therefore, for the cell where
most UEs are in fast
movement, this parameter
can be set to a smaller
value, whereas for the cell
where most UEs are in slow
movement, this parameter
can be set to a greater
value. The value of this
algorithm becomes fast in
responding to signal change;
however, the probability of
incorrect decision becomes
high.
The emulation result shows
that the hysteresis setting
can effectively reduce the
average number of
handovers and the number
of incorrect handovers, thus
preventing unnecessary
handovers. The emulation
result also shows that the
UE at different data rates
may react differently to the
delay for triggering the
Cell TrigTime3A 3A Event Trigger Delay Time event. For the fast-moving
UE, the call drop rate is
more sensitive to the delay,
whereas, for the slow-
moving UE, the call drop
rate is less sensitive to the
delay. This can also reduce
ping-pong handovers and
incorrect handovers.
Therefore, for the cell where
most UEs are in fast
movement, this parameter
can be set to a smaller
value, whereas for the cell
where most UEs are in slow
movement, this parameter
can be set to a greater
value. The value of this
recommended threshold is
-12 dB. In actual networks,
set this parameter to -14 dB
because the UEs in a cell
usually move at different
speeds. The emulation
result shows that the call
drop rate remains low for
the UEs moving at a speed
of 120 km/h when this
parameter is set to -14 dB.
If the cell is a macro cell, it
indicates that micro cells
exist in this cell. To enable
the micro cells to handle
more traffic, the
compressed mode start and
Inter-RAT CS Measure Start stop thresholds should be
Cell InterRATCSThd2DEcN0 Ec/No THD set higher, that is, the
thresholds for events 2D and
2F using CPICH RSCP are set
higher.
If the cell is a micro cell, the
default value should be
modified according to the
link budgeting result.
Event 2D and event 2F are
used to enable and disable
the compressed mode
respectively. When the cell
is located in the center of
the frequency coverage or
the inter-frequency
measurement quantity uses
both Ec/No and RSCP, then
the Ec/No value is used as
recommended threshold is
-12 dB.
In actual networks, set this
parameter to -14 dB
because the UEs in a cell
usually move at different
speeds. The emulation
result shows that the call
drop rate remains low for
the UEs moving at a speed
of 120 km/h when this
parameter is set to -14 dB.
If the cell is a macro cell, it
indicates that micro cells
exist in this cell. To enable
the micro cells to handle
more traffic, the
Inter-RAT R99 PS Measure
Cell InterRATR99PsThd2DEcN0 Start Ec/No THD compressed mode start and
stop thresholds should be
set higher, that is, the
thresholds for events 2D and
2F using CPICH RSCP are set
higher.
If the cell is a micro cell, the
default value should be
modified according to the
link budgeting result.
Event 2D and event 2F are
used to enable and disable
the compressed mode
respectively. When the cell
is located in the center of
the frequency coverage or
the inter-frequency
measurement quantity uses
When RSCP is used as the
measurement quantity for
PS domain non-HSPA
services, the UE reports
event 2D when the
measured RSCP value is
lower than this threshold.
Then, the RNC sends the
signaling to enable the
compressed mode and start
the inter-RAT measurement.
To enable the compressed
mode earlier, increase the
threshold of triggering event
2D; otherwise, decrease the
threshold of triggering event
2D. To prevent the frequent
Inter-RAT R99 PS Measure enabling and disabling of the
Cell InterRATR99PsThd2DRSCP Start RSCP THD compressed mode, increase
the difference between the
thresholds of triggering
event 2D and event 2F.
In most cases, users want to
be maintained within a 3G
network. Therefore, the
start threshold of the inter-
RAT measurement is set
smaller than that of the
inter-frequency
measurement in order to
trigger inter-frequency
easily. In scenarios where
inter-frequency neighboring
cells are unavailable or
where inter-frequency
coverage is insufficient, the
"PERIODICAL_REPORTING",
this parameter is used for
the assessment of inter-RAT
coverage handover. That is,
Tother_RAT in the following
formulas. This parameter is
the absolute threshold of
the cell of another RAT
(Received Signal Strength
Indicator: RSSI) for the inter-
RAT handover decision.
If the quality of the cell of
another RAT in the inter-RAT
measurement report fulfils
the following criterion:
Mother_RAT + CIO >=
Tother_RAT + H/2
Inter-RAT CS Handover Then, the system starts the
Cell TargetRatCsThd Decision THD trigger timer, and makes the
handover decision after the
timer expires. If the quality
of the cell of another RAT
fulfills the following criterion
before timeout:
Mother_RAT + CIO <
Tother_RAT - H/2
The RNC stops the timer and
waits for another inter-RAT
measurement report.
Here,
Mother_RAT is the
measurement result of the
GSM RSSI.
Tother_RAT is the inter-RAT
handover decision
threshold.
"PERIODICAL_REPORTING",
this parameter is used for
the assessment of inter-RAT
coverage handover. That is,
Tother_RAT in the following
formulas. This parameter is
the absolute threshold of
the cell of another RAT
(Received Signal Strength
Indicator: RSSI) for the inter-
RAT handover decision.
If the quality of the cell of
another RAT in the inter-RAT
measurement report fulfils
the following criterion:
Mother_RAT + CIO >=
Tother_RAT + H/2
Inter-RAT R99 PS Handover Then, the system starts the
Cell TargetRatR99PsThd Decision THD trigger timer, and makes the
handover decision after the
timer expires. If the quality
of the cell of another RAT
fulfills the following criterion
before timeout:
Mother_RAT + CIO <
Tother_RAT - H/2
The RNC stops the timer and
waits for another inter-RAT
measurement report.
Here,
Mother_RAT is the
measurement result of the
GSM RSSI.
Tother_RAT is the inter-RAT
handover decision
threshold.
"PERIODICAL_REPORTING",
this parameter is used for
the assessment of inter-RAT
coverage handover. That is,
Tother_RAT in the following
formulas. This parameter is
the absolute threshold of
the cell of another RAT
(Received Signal Strength
Indicator: RSSI) for the inter-
RAT handover decision.
If the quality of the cell of
another RAT in the inter-RAT
measurement report fulfils
the following criterion:
Mother_RAT + CIO >=
Tother_RAT + H/2
Inter-RAT HSPA Handover Then, the system starts the
Cell TargetRatHThd Decision THD trigger timer, and makes the
handover decision after the
timer expires. If the quality
of the cell of another RAT
fulfills the following criterion
before timeout:
Mother_RAT + CIO <
Tother_RAT - H/2
The RNC stops the timer and
waits for another inter-RAT
measurement report.
Here,
Mother_RAT is the
measurement result of the
GSM RSSI.
Tother_RAT is the inter-RAT
handover decision
threshold.
threshold can directly affect
the SHO ratio. Therefore,
the threshold should be
wisely chosen to achieve
smooth SHOs. The value of
this parameter determines
the SHO area and SHO ratio.
In the CDMA system, the
ratio of the UE involved in
soft handover should reach
30% to 40% to ensure
smooth handover. Based on
simulation results, when the
relative threshold is set to 5
dB, the ratio of the UE
involved in soft handover
(the number of cells in the
VP Service Event 1B Relative active set is at least 2) is
Cell IntraRelThdFor1BCSVP Threshold about 35%. You are advised
to set the relative threshold
to a great value (5 dB to 7
dB) during site deployment,
and to reduce the threshold
when the users increase. the
threshold must be higher
than 3 dB to avoid the ping-
pong handover.
You can set different relative
thresholds for event 1A and
event 1B to reduce the ping-
pong effect and change the
soft handover ratio. In
general applications, the
relative thresholds for
events 1A and 1B should be
consistent, and you can curb
threshold can directly affect
the SHO ratio. Therefore,
the threshold should be
wisely chosen to achieve
smooth SHOs. The value of
this parameter determines
the SHO area and SHO ratio.
In the CDMA system, the
ratio of the UE involved in
soft handover should reach
30% to 40% to ensure
smooth handover. Based on
simulation results, when the
relative threshold is set to 5
dB, the ratio of the UE
involved in soft handover
(the number of cells in the
CS Non-VP Service Event 1B active set is at least 2) is
Cell IntraRelThdFor1BCSNVP Relative Threshold about 35%. You are advised
to set the relative threshold
to a great value (5 dB to 7
dB) during site deployment,
and to reduce the threshold
when the users increase. the
threshold must be higher
than 3 dB to avoid the ping-
pong handover.
You can set different relative
thresholds for event 1A and
event 1B to reduce the ping-
pong effect and change the
soft handover ratio. In
general applications, the
relative thresholds for
events 1A and 1B should be
consistent, and you can curb
threshold can directly affect
the SHO ratio. Therefore,
the threshold should be
wisely chosen to achieve
smooth SHOs. The value of
this parameter determines
the SHO area and SHO ratio.
In the CDMA system, the
ratio of the UE involved in
soft handover should reach
30% to 40% to ensure
smooth handover. Based on
simulation results, when the
relative threshold is set to 5
dB, the ratio of the UE
involved in soft handover
(the number of cells in the
PS Service Event 1B Relative active set is at least 2) is
Cell IntraRelThdFor1BPS Threshold about 35%. You are advised
to set the relative threshold
to a great value (5 dB to 7
dB) during site deployment,
and to reduce the threshold
when the users increase. the
threshold must be higher
than 3 dB to avoid the ping-
pong handover.
You can set different relative
thresholds for event 1A and
event 1B to reduce the ping-
pong effect and change the
soft handover ratio. In
general applications, the
relative thresholds for
events 1A and 1B should be
consistent, and you can curb
This parameter specifies the
hysteretic value for event
1A. For details on the
definition of event 1A, see
3GPP TS 25.331.
Event 1A, as a key event,
refers to the event triggered
when a cell is added to the
active set. To ensure that
the handover is triggered
timely, the hysteresis for
event 1A should be smaller
than the hysteresis used for
events 1B, 1F, 1C, and 1D. A
too large difference
Cell HystFor1A 1A Hysteresis between the hysteresis
values affects the ratio of
soft handovers (SHOs). In
addition, filter coefficient
and trigger delay must be
considered in setting this
parameter. The value of this
parameter is associated with
slow fading. If this
parameter is set to a large
value, the possibility of ping-
pong handovers and
incorrect handover
decisions decreases but
events cannot be triggered
timely.
Ec/No threshold of
triggering the inter-
frequency measurement for
HSPA services.
When Ec/No is used as the
measurement quantity for
inter-frequency handovers
RNC InterFreqHThd2DEcN0 Inter-freq H Measure Start of HSPA services, the UE
Ec/No THD reports event 2D when the
measured Ec/No value is
lower than the value of this
parameter. Then, the RNC
sends a signaling message to
activate the compression
mode and start the inter-
frequency measurement.
Ec/No threshold of stopping
the inter-frequency
measurement for PS non-
HSPA services.
When Ec/No is used as the
measurement quantity for
inter-frequency handovers
RNC InterFreqR99PsThd2FEcN0 Inter-freq R99 PS Measure of PS non-HSPA services, the
Stop Ec/No THD UE reports event 2F when
the measured Ec/No value is
higher than the value of this
parameter. Then, the RNC
sends a signaling message to
deactivate the compression
mode and stop the inter-
frequency measurement.
{412,437,462,487,512,537,5
62,587,612,637,662,687}
Band3
General frequencies: [1162-
1513]
Additional frequencies:
none
Band4
General frequencies: [1537-
1738]
Additional frequencies:
{1887, 1912, 1937, 1962,
1987, 2012, 2037, 2062,
2087}
Band5
General frequencies: [4357-
4458]
Additional frequencies:
Cell UARFCNDownlink UARFCNDownlink
{1007, 1012, 1032,1037,
1062, 1087}
Band6
General frequencies: [4387-
4413]
Additional frequencies:
{1037, 1062}
Band7
General frequencies: [2237-
2563]
Additional frequencies:
{2587, 2612, 2637, 2662,
2687, 2712, 2737, 2762,
2787, 2812, 2837, 2862,
2887, 2912}
Band8
General frequencies: [2937-
3088]
Hysteresis for triggering
event 2D.
When
"InterFreqReportMode" is
set to
PERIODICAL_REPORTING,
the hysteresis in active set
quality measurement is used
to prevent the ping-pong
reporting of event 2D
(triggered when the
estimated quality of the
frequency in use is lower
than the threshold) and
event 2F (triggered when
Cell HystFor2D HystFor2D the estimated quality of the
frequency in use is higher
than the threshold). Event
2D is used to enable the
compression mode and
event 2F is used to disable
the compression mode.To
prevent the compression
mode from being frequently
enabled and disabled, you
can set "Hystfor2D" and
"Hystfor2F" to be greater
than their recommended
values according to the
statistics of the ping-pong
inter-frequency handover.
Hysteresis for triggering
event 2F.
When
"InterFreqReportMode" is
set to
PERIODICAL_REPORTING,
the hysteresis in active set
quality measurement is used
to prevent the ping-pong
reporting of event 2D
(triggered when the
estimated quality of the
frequency in use is lower
than the threshold) and
event 2F (triggered when
Cell HystFor2F HystFor2F the estimated quality of the
frequency in use is higher
than the threshold). Event
2D is used to enable the
compression mode and
event 2F is used to disable
the compression mode.To
prevent the compression
mode from being frequently
enabled and disabled, you
can set "Hystfor2D" and
"Hystfor2F" to be greater
than their recommended
values according to the
statistics of the ping-pong
inter-frequency handover.
Hysteresis for triggering
event 2D.
When
"InterFreqReportMode" is
set to
PERIODICAL_REPORTING,
the hysteresis in active set
quality measurement is used
to prevent the ping-pong
reporting of event 2D
(triggered when the
estimated quality of the
frequency in use is lower
than the threshold) and
event 2F (triggered when
Cell Hystfor2D Hystfor2D the estimated quality of the
frequency in use is higher
than the threshold). Event
2D is used to enable the
compression mode and
event 2F is used to disable
the compression mode.To
prevent the compression
mode from being frequently
enabled and disabled, you
can set "Hystfor2D" and
"Hystfor2F" to be greater
than their recommended
values according to the
statistics of the ping-pong
inter-frequency handover.
Hysteresis for triggering
event 2F.
When
"InterFreqReportMode" is
set to
PERIODICAL_REPORTING,
the hysteresis in active set
quality measurement is used
to prevent the ping-pong
reporting of event 2D
(triggered when the
estimated quality of the
frequency in use is lower
than the threshold) and
event 2F (triggered when
Cell Hystfor2F Hystfor2F the estimated quality of the
frequency in use is higher
than the threshold). Event
2D is used to enable the
compression mode and
event 2F is used to disable
the compression mode.To
prevent the compression
mode from being frequently
enabled and disabled, you
can set "Hystfor2D" and
"Hystfor2F" to be greater
than their recommended
values according to the
statistics of the ping-pong
inter-frequency handover.
This parameter specifies the
interval time between
detection of event 1D and
sending of the measurement
report. The value of this
parameter is associated with
slow fading. If this
parameter is set to a greater
value, the probability of
incorrect decision becomes
low; however, the handover
algorithm becomes slow in
responding to signal change.
The time-to-trigger
mechanism is introduced for
Cell TrigTime1D TrigTime1D the following purposes:
- reducing the number of
wrong event reports caused
by burst signals,
- preventing the ping-pong
handover,
- reducing the impact of
shadow fading on event
decisions.
Setting an appropriate
interval time effectively
reduces the average number
of handovers and the
number of wrong
handovers, preventing
unnecessary handovers.
Hysteresis for triggering
event 2D.
When
"InterFreqReportMode" is
set to
PERIODICAL_REPORTING,
the hysteresis in active set
quality measurement is used
to prevent the ping-pong
reporting of event 2D
(triggered when the
estimated quality of the
frequency in use is lower
than the threshold) and
event 2F (triggered when
RNC HystFor2D HystFor2D the estimated quality of the
frequency in use is higher
than the threshold). Event
2D is used to enable the
compression mode and
event 2F is used to disable
the compression mode.To
prevent the compression
mode from being frequently
enabled and disabled, you
can set "Hystfor2D" and
"Hystfor2F" to be greater
than their recommended
values according to the
statistics of the ping-pong
inter-frequency handover.
Hysteresis for triggering
event 2F.
When
"InterFreqReportMode" is
set to
PERIODICAL_REPORTING,
the hysteresis in active set
quality measurement is used
to prevent the ping-pong
reporting of event 2D
(triggered when the
estimated quality of the
frequency in use is lower
than the threshold) and
event 2F (triggered when
RNC HystFor2F HystFor2F the estimated quality of the
frequency in use is higher
than the threshold). Event
2D is used to enable the
compression mode and
event 2F is used to disable
the compression mode.To
prevent the compression
mode from being frequently
enabled and disabled, you
can set "Hystfor2D" and
"Hystfor2F" to be greater
than their recommended
values according to the
statistics of the ping-pong
inter-frequency handover.
Hysteresis for triggering
event 2D.
When
"InterFreqReportMode" is
set to
PERIODICAL_REPORTING,
the hysteresis in active set
quality measurement is used
to prevent the ping-pong
reporting of event 2D
(triggered when the
estimated quality of the
frequency in use is lower
than the threshold) and
event 2F (triggered when
RNC Hystfor2D Hystfor2D the estimated quality of the
frequency in use is higher
than the threshold). Event
2D is used to enable the
compression mode and
event 2F is used to disable
the compression mode.To
prevent the compression
mode from being frequently
enabled and disabled, you
can set "Hystfor2D" and
"Hystfor2F" to be greater
than their recommended
values according to the
statistics of the ping-pong
inter-frequency handover.
Hysteresis for triggering
event 2F.
When
"InterFreqReportMode" is
set to
PERIODICAL_REPORTING,
the hysteresis in active set
quality measurement is used
to prevent the ping-pong
reporting of event 2D
(triggered when the
estimated quality of the
frequency in use is lower
than the threshold) and
event 2F (triggered when
RNC Hystfor2F Hystfor2F the estimated quality of the
frequency in use is higher
than the threshold). Event
2D is used to enable the
compression mode and
event 2F is used to disable
the compression mode.To
prevent the compression
mode from being frequently
enabled and disabled, you
can set "Hystfor2D" and
"Hystfor2F" to be greater
than their recommended
values according to the
statistics of the ping-pong
inter-frequency handover.
According to 3GPP TS
25.331, the filtered
measurement value is
calculated using the
following formula, where k
represents this parameter:
Fn = (1 - a) * Fn - 1 + a * Mn
a = 1/(2 ^ (k/2))
Here,
Fn: filtered measurement
result
Fn - 1: previously filtered
measurement result
Mn: latest received
measurement result from
physical layer
When a is set to 1, L3
RNC FilterCoef FilterCoef filtering is not applied.
The input measurement
value to L3 filter has been
filtered by L1 filter, where
the impact of fast fading is
almost eliminated. In this
case, smooth filtering should
be applied through L3 filter,
to eliminate the effect of
shadow fading and peaks
caused by fast fading, thus
the filtered measurement
value can reflect the
variation of the actual
measurement value, and
provide more reliable
measurement result for
event judgment.
Measurement quantity for
triggering intra-frequency
handovers. Reference
measurement quantity for a
UE to report event 1x.
For intra-frequency
handovers, CPICH Ec/No or
RSCP is used as the
measurement quantity. For
events 1A, 1B, 1C, and 1D
which adopt relative
thresholds, the
measurement quantity does
not have great impact on
the threshold values. For
event 1F which adopts
absolute threshold, the
measurement quantity
RNC IntraFreqMeasQuantity IntraFreqMeasQuantity should be set based on
actual cell conditions. If the
cell is located in the center
of the coverage area, the
main factor that affects
signal quality is intra-
frequency interference. In
this case, you are advised to
set this parameter to
CPICH_EC/NO. If the cell is
located at the edge of the
coverage area, the main
factor that affects signal
quality is the distance
between the cell and the
base station. In this case,
you are advised to set this
parameter to CPICH_RSCP.
CN domain specific
Discontinuous Reception
(DRX) cycle length
RNC DRXCycleLenCoef DRXCycleLenCoef coefficient broadcast on
SIB1 and used by UEs in Idle
Mode.
Used for calculating the
relative threshold of the soft
handover based on the
measurement report of each
cell in the active set. If this
parameter is set to a greater
value, the relative threshold
of the soft handover is
greater with the other
conditions unchanged. For
detailed information of this
parameter, see 3GPP TS
25.133. When this
parameter is set to 0, the
general quality of the active
RNC Weight Weight set is the quality of the best
cell. In this case, the relative
threshold of soft handover
depends on the related
measurement values of the
best cell in the active set.
When this parameter is set
to 1, the relative threshold
of the soft handover
depends on the equivalent
signal strength obtained
when maximum ratio
combining is performed in
the downlink of all cells in
the active set.
Cell offset used for CPICH
RSCP measurement value in
cell selection or reselection
when the UE is in connected
mode. During cell selection
or reselection, "QOffset1sn"
is the cell offset
corresponding to CPICH
RSCP, and "QOffset2sn" is
the cell offset corresponding
to CPICH Ec/No. For details
about "QOffset1sn" and
"QOffset2sn", see 3GPP TS
25.331. "QOffset1sn" and
"QOffset2sn" are used when
Cell ConnQoffset1sn ConnQoffset1sn the UE is in idle mode, while
"ConnQoffset1sn" and
"ConnQoffset2sn" are used
when the UE is in connected
mode. "ConnQoffset1sn"
and "ConnQoffset2sn" are
valid only if the SIB12
message is available. The
measured value of the
neighboring cell minus the
value of this parameter is
used for cell reselection
ranking. This parameter
needs to be set based on the
actual situation.
Cell offset used for CPICH
Ec/No measurement value
in cell selection or
reselection when the UE is
in connected mode. During
cell selection or reselection,
"QOffset1sn" is the cell
offset corresponding to
CPICH RSCP, and
"QOffset2sn" is the cell
offset corresponding to
CPICH Ec/No. For details
about "QOffset1sn" and
"QOffset2sn", see 3GPP TS
25.331. "QOffset1sn" and
"QOffset2sn" are used when
Cell ConnQoffset2sn ConnQoffset2sn the UE is in idle mode, while
"ConnQoffset1sn" and
"ConnQoffset2sn" are used
when the UE is in connected
mode. "ConnQoffset1sn"
and "ConnQoffset2sn" are
valid only if the SIB12
message is available. The
measured value of the
neighboring cell minus the
value of this parameter is
used for cell reselection
ranking. This parameter
needs to be set based on the
actual situation.
Maximum number of cells in
an active set. This parameter
is used to achieve the
balance between the signal
quality in the SHO area and
the system performance. If
more cells are in the active
set, a user can obtain a
greater macro diversity gain;
the intra-frequency
interference is smaller. In
this case, however, the user
occupies resources of
several cells. This increases
the amount of data to be
RNC MaxCellInActiveSet MaxCellInActiveSet processed and lowers the
system performance. To
reduce intra-frequency
interference, it is
recommended that the
number of cells in the active
sets should be increased in
the hot-spot and micro cells,
where the signals are
complicated. For the cell
that provides high speed
services, the decrease in
cells in the active set can
reduce the consumption of
system resources.
Cell offset used for CPICH
RSCP measurement value in
cell selection or reselection
when the UE is in connected
mode. During cell selection
or reselection, "QOffset1sn"
is the cell offset
corresponding to CPICH
RSCP, and "QOffset2sn" is
the cell offset corresponding
to CPICH Ec/No. For details
about "QOffset1sn" and
"QOffset2sn", see 3GPP TS
25.331. "QOffset1sn" and
"QOffset2sn" are used when
Cell ConnQoffset1sn ConnQoffset1sn the UE is in idle mode, while
"ConnQoffset1sn" and
"ConnQoffset2sn" are used
when the UE is in connected
mode. "ConnQoffset1sn"
and "ConnQoffset2sn" are
valid only if the SIB12
message is available. The
measured value of the
neighboring cell minus the
value of this parameter is
used for cell reselection
ranking. This parameter
needs to be set based on the
actual situation.
Cell offset used for CPICH
Ec/No measurement value
in cell selection or
reselection when the UE is
in connected mode. During
cell selection or reselection,
"QOffset1sn" is the cell
offset corresponding to
CPICH RSCP, and
"QOffset2sn" is the cell
offset corresponding to
CPICH Ec/No. For details
about "QOffset1sn" and
"QOffset2sn", see 3GPP TS
25.331. "QOffset1sn" and
"QOffset2sn" are used when
Cell ConnQoffset2sn ConnQoffset2sn the UE is in idle mode, while
"ConnQoffset1sn" and
"ConnQoffset2sn" are used
when the UE is in connected
mode. "ConnQoffset1sn"
and "ConnQoffset2sn" are
valid only if the SIB12
message is available. The
measured value of the
neighboring cell minus the
value of this parameter is
used for cell reselection
ranking. This parameter
needs to be set based on the
actual situation.
Whether a UE in the
CELL_PCH or URA_PCH state
preferentially performs a
state transition from
CELL_PCH or URA_PCH to
CELL_DCH or CELL_FACH
before initiating a CS
service. 1: This switch is
turned on. The RNC first
RNC CS_SETUP_P2D_SWITCH CS_SETUP_P2D_SWITCH
performs a state transition
from CELL_PCH or URA_PCH
to CELL_DCH and then
initiates the CS service. 0:
This switch is turned off. The
UE first performs a state
transition from CELL_PCH or
URA_PCH to CELL_FACH and
then initiates the CS service.
Estimated retransmission
rate of signaling packets
when combined services are
performed. This parameter
is used to calculate the
activation time contained in
the RB SETUP or RB RECFG
RNC PacketReTransRatio PacketReTransRatio messages in scenarios with
combined services. A large
value of this parameter
leads to long activation time.
To modify this parameter,
contact Huawei Customer
Service Center for technical
support
Whether to prohibit channel
retries for CS and PS
combined services. When
this switch is turned on,
channel retries are
DRA_CSPS_NO_PERIOD_RET DRA_CSPS_NO_PERIOD_RET
RNC RY_SWITCH RY_SWITCH prohibited for CS and PS
combined services. When
this switch is turned off,
channel retries are allowed
for CS and PS combined
services.
Number of CQI
retransmissions when the
UE is in the single-RLS state.
Assume that the CQI
Cell CQIReF CQIReF
repetition factor is N. The
receiver performs soft
combining on N results
before decoding.
Number of CQI
retransmissions when the
UE is in the multi-RLS state.
Assume that the CQI
Cell CQIReFforSHO CQIReFforSHO
repetition factor is N. The
receiver performs soft
combining on N results
before decoding.
OptimizationSwitch OptimizationSwitch
RNC #N/A
=MC_RL_RESET_SWITCH =MC_RL_RESET_SWITCH
Maximum number of
successive "out of sync"
indications received from
Layer 1. The protocol-
RNC N313 N313
defined default value is 20.
The value of this parameter
is contained in SIB1
messages
synchronization failure are
fulfilled and only RBs
associated with T314 exist.
T314 stops when the cell
update procedure is
completed. The protocol-
defined default value is 12.
When a UE in the CELL_DCH
state experiences a radio
link synchronization failure,
the UE starts T315 or T314
and sends a CELL UPDATE
message. Before T314 or
T315 expires, the UE
resends the CELL UPDATE
message if radio link
reconfiguration through the
CELL UPDATE CONFIRM
RNC T314 T314 message fails. This provides
an opportunity for radio link
reconfiguration, which is
associated with T302 and
N302. It is recommended
that T314 be set to a value
greater than the product of
T302 and N302. The smaller
the value of T314 is, the
higher the call drop rate of
the corresponding service is.
When T314 expires and the
UE is performing a CS
service, or T315 expires and
the UE is performing a PS
service, the RNC releases
the RRC connection. The
value of this parameter is
synchronization failure are
fulfilled and only RBs
associated with T315 exist.
T315 stops when the cell
update procedure is
completed. The protocol-
defined default value is 180.
When a UE in the CELL_DCH
state experiences a radio
link synchronization failure,
the UE starts T315 or T314
and sends a CELL UPDATE
message. Before T314 or
T315 expires, the UE
resends the CELL UPDATE
message if radio link
reconfiguration through the
CELL UPDATE CONFIRM
RNC T315 T315 message fails. This provides
an opportunity for radio link
reconfiguration, which is
associated with T302 and
N302. It is recommended
that T315 be set to a value
greater than the product of
T302 and N302. The smaller
the value of T315 is, the
higher the call drop rate of
the corresponding service is.
When T314 expires and the
UE is performing a CS
service, or T315 expires and
the UE is performing a PS
service, the RNC releases
the RRC connection. The
value of this parameter is
Timer 302. T302 starts when
a UE sends a CELL
UPDATE/URA UPDATE
message and stops when
the UE receives a CELL
UPDATE CONFIRM/URA
UPDATE CONFIRM message.
When T302 expires, the UE
resends a CELL UPDATE/URA
UPDATE message if the
RNC T302 T302 value of the counter V302 is
smaller than or equal to that
of the parameter N302. If
the value of V302 is larger
than that of N302 when
T302 expires, the UE enters
the idle mode. The protocol-
defined default value is
4000. The value of this
parameter is contained in
SIB1 messages
Maximum number of
retransmissions of the CELL
UPDATE/URA UPDATE
message. The protocol-
RNC N302 N302
defined default value is 3.
The value of this parameter
is contained in SIB1
messages.
Maximum number of
successive "in sync"
indications received from
Layer 1 after T313 starts.
RNC N315 N315 The protocol-defined default
value is 1. The value of this
parameter is contained in
SIB1 messages.
Number of times of
successive in-sync
indications required for
starting the radio link failure
timer. When the radio link
set is in the synchronized
state, the NodeB starts the
timer after it receives
successive out-of-sync
indications of the number
defined by "NOutsyncInd".
The NodeB shall stop and
Cell NOutsyncInd NOutsyncInd reset the timer after
receiving successive in-sync
indications of the number
defined by "NInsyncInd".
"TRlFailure" specifies the
length of the timer. When
the timer expires, the
NodeB triggers the radio link
failure process, and
indicates which radio link
set is out-of-sync.
Number of times of
successive in-sync
indications required for the
NodeB to trigger the radio
link recovery process. The
radio link set remains in the
initial state until it has
received a number (the
number is defined by
"NInsyncInd") of successive
in-sync indications from L1,
Cell NInsyncInd NInsyncInd and then the NodeB triggers
the radio link recovery
process, which indicates
that the radio link set has
been synchronized. Once
the radio link recovery
process is triggered, the
radio link set is considered
to be in the synchronized
state. In the radio link
maintenance process.
RETRYCAPABILITY:SRB_OVER RETRYCAPABILITY:SRB_OVER
RNC _HSUPA _HSUPA #N/A
After a UE fails to be
handed over to a 2G cell
during an inter-RAT
handover, the RNC forbids
the UE to attempt a
PERFENH_INTERRAT_PENAL PERFENH_INTERRAT_PENAL
RNC TY_50_SWITCH TY_50_SWITCH handover to the 2G cell in a
certain period. When the
switch is set to ON, the
period is 50s. When the
switch is set to OFF, the
period is 30s.
Determines whether
preemption is supported.
When this switch is enabled,
the RNC allows privileged
users or services to preempt
cell resources from the
users or services with the
RNC PreemptAlgoSwitch PreemptAlgoSwitch preempted attributes and
lower priority in the case of
cell resource insufficiency.
When the switch is disabled,
the RNC terminates the
service for the user due to
the failure in cell resource
application
Whether preemption is
allowed when the CPU load
is high. When this switch is
turned on, a user checks the
CPU load when attempting
to preempt other users'
resources due to insufficient
PREEMPT_ENH_CPU_HIGHL PREEMPT_ENH_CPU_HIGHL cell resources and cannot
RNC
OAD_CTRL_SWITCH OAD_CTRL_SWITCH preempt other users'
resources when the CPU
usage is higher than 70%.
When this switch is turned
off, the user does not
consider the CPU load when
preempting other users'
resources
Combined-service-specific
CQI feedback period for a
cell where UEs are
CELL CQIFBckBaseCsCombServ CQIFBckBaseCsCombServ processing CS services
carried over the DCH and PS
services carried over the
HSDPA
FACH_USER_NUM_NOT_CT FACH_USER_NUM_NOT_CT
CELL RL RL #N/A
RB_RECFG_RL_REEST_SWIT RB_RECFG_RL_REEST_SWIT
RNC CH CH #N/A
NON_DCCC_RBRECFG_RL_R NON_DCCC_RBRECFG_RL_R
RNC #N/A
EEST_SWITCH EEST_SWITCH
RNC SMC_RL_REEST_SWITCH SMC_RL_REEST_SWITCH #N/A
PSINACTTMRFORFSTDRMDC PSINACTTMRFORFSTDRMDC
RNC H H #N/A
RNC T323 T323 #N/A
PSINACTTMRFORPREFSTDR PSINACTTMRFORPREFSTDR
RNC M M #N/A
Whether the compressed
mode (CM) can coexist with
the HSUPA service. If this
parameter is set to Permit:
1. the RNC can enable the
CM for HSUPA services. 2.
The HSUPA services can be
enabled when the CM is
enabled. If this parameter is
set to Limited: 1. the CM for
HSUPA services can be
enabled only after the E2D
(E-DCH to DCH) channel
switch. 2. The HSUPA
services cannot be enabled
RNC HsupaCMPermissionInd HsupaCMPermissionInd when the CM is enabled. If
this parameter is set to
BasedonUECap, the RNC
determines whether CM can
be enabled for HSUPA
services and whether HSUPA
services can be enabled
when the CM is enabled by
considering the UE
capability.
This switch is used for the
compatibility of the HSUPA
terminals that do not
support CM when HSUPA is
enabled.
CMP_F2D_RLC_ONESIDE_RE CMP_F2D_RLC_ONESIDE_RE
RNC BUILD_SWITCH BUILD_SWITCH #N/A
CMP_D2F_RLC_ONESIDE_RE CMP_D2F_RLC_ONESIDE_RE
RNC #N/A
BUILD_SWITCH BUILD_SWITCH
RNC 关闭2ms周期重试
P-CPICH Ec/N0 on RACH更新
RNC
优化
设置“No有效信号质量报
RNC
告时的ECN0假定值”
HSUPA用户TTI重配置流程
RNC
优化
PERFENH_HRNTI_OPT_SWIT
RNC
CH
PERFENH_SRB_OVER_HSUP PERFENH_SRB_OVER_HSUP
RNC
A_TTI10_SWITCH A_TTI10_SWITCH
RNC E2FTHROUTHD E2FTHROUTHD
RNC_RB_SCRI_NOT_DROP_S RNC_RB_SCRI_NOT_DROP_S
RNC
WITCH WITCH
IRATHO_CNT_CORRECT_SWI IRATHO_CNT_CORRECT_SWI
RNC TCH TCH
Huawei E///
ADD UCELLACCESSSTRICT NOT_BARRED RESERVED 0
NOT_RESERVED 1
(HW)
MaxTargetUlLoadFactor =
Min [90%, Max ((1-1 / 10 ^
(eulMaxOwnUuLoad / 100)),
(1-1 / 10 ^
(eulMaxRotCoverage /
ADD UCELLHSUPA 75 100)))], if the result of the
mapping values greater than
or equal 83 %, you need to
synchronize modify HW
parameter MOD UCELLCAC:
CELLID = xxx, UlCellTotalThd
= 91;
ADD UCELLCAC 95
ADD UCELLCAC 64
ADD UCELLCAC 20
ADD UBCH -20 use E/// value
powerOffsetPpm =
powerOffsetPpm (ADD
UPRACHTFC command CTFC
= 1 and CTFC = 0, two CTFC
In signaling transmission powerOffsetPpm
mode, set PowerOffsetPpm corresponding maps in the
ADD UPRACHTFC to -3; in service transmission original network the same
mode, set PowerOffsetPpm value)
to -2. Note: The relocation project
in the production of the
script, based on a script RNC
baseline, RMV UPRACHTFC,
then ADD UPRACHTFC.
[HW]
HsPdschMPOConstEnum =
Round [([E ///]
maximumTransmissionPowe
r - primaryCpichPower -
ADD UCELLHSDPA 2.5dB hsMeasurementPowerOffse
t) / 10], the nearest values.
Such as 6.1, taken in
accordance with 6.0, 5.4
taken in accordance with
5.5. Step 0.5
E/// HUAWEI
SET UHSDPCCH D2
X DX
SET UCORRMALGOSWITCH 0
E/// HUAWEI
ADD UCNDOMAIN ALLOWED 1 ALLOWED
0 NOT_ALLOWED
E/// HUAWEI
ADD UCNDOMAIN MODE2 0 MODE1
1 MODE2
ADD UCELLALGOSWITCH No
ADD UCELLALGOSWITCH No
ADD UCELLALGOSWITCH No
ADD UCELLALGOSWITCH No
ADD UCELLALGOSWITCH No
ADD UCELLALGOSWITCH No
ADD UCELLALGOSWITCH No
Huawei E///
ADD UCELLHSDPA Automatic Automatic 1
Manual 0
SET UCORRMALGOSWITCH 0
E/// HUAWEI
ADD UCELLSETUP 0 0 FALSE
1 TRUE
D1024 BEF2DTVMTHD
SET UUESTATETRANS D256 D2F2PTVMTHD
SET URRCTRLSWITCH 0
SET UCORRMALGOSWITCH 0
SET UCORRMALGOSWITCH 0
IF [E///]qRxLevMin (MO
Class
Name:vsDataExternalGsmCe
ll)==100,
[HUAWEI]qRxLevMin=([E///]
qRxLevMin (MO Class
ADD U2GNCELL -50 Name:vsDataUtranCell)
+115)/2-58;
ELSE
[HUAWEI]qRxLevMin=([E///]
qRxLevMin (MO Class
Name:vsDataExternalGsmCe
ll) + 115)/2 - 58
ADD UCELLSELRESEL 1 use E/// value
ADD UCELLSELRESEL -18 use E/// value
[HUAWEI]TimeToTrig2D =
ADD D(min([E///]timeToTrigger2
UCELLINTERFREQHOCOV D320 dEcno,
[E///]timeToTrigger2dRscp))
[HUAWEI]TimeToTrig2F =
ADD D1280 D(min([E///]timeToTrigger2f
UCELLINTERFREQHOCOV Ecno,
[E///]timeToTrigger2fRscp))
[HUAWEI]TimeToTrig2D =
D(min([E///]timeToTrigger2
SET UINTERFREQHOCOV D320 dEcno,
[E///]timeToTrigger2dRscp))
[HUAWEI]TimeToTrig2F =
SET UINTERFREQHOCOV D1280 D(min([E///]timeToTrigger2f
Ecno,
[E///]timeToTrigger2fRscp))
使用E///
<es:userLabel>Conv. CS
speech 12.2 ,
preconfigured</es:userLabel
>下的
serviceOffset2dEcno。
如果[E///]
SET UINTERFREQHOCOV -14 (usedFreqThresh2dEcno+ser
viceOffset2dEcno)<-24,则
[HUAWEI]InterFreqCSThd2D
EcN0=-24;
否则:
[HUAWEI]InterFreqCSThd2D
EcN0=[E///]
(usedFreqThresh2dEcno+ser
viceOffset2dEcno)
使用E///
<es:userLabel>Conv. CS
speech 12.2 ,
preconfigured</es:userLabel
>下的
serviceOffset2dEcno。
如果[E///]
(usedFreqThresh2dEcno+ser
SET UINTERFREQHOCOV -12 viceOffset2dEcno+usedFreq
RelThresh2fEcno)<-24,则
[HUAWEI]InterFreqCSThd2F
EcN0=-24;
否则:
[HUAWEI]InterFreqCSThd2F
EcN0=[E///]
(usedFreqThresh2dEcno+ser
viceOffset2dEcno+usedFreq
RelThresh2fEcno)
SET UINTERFREQHOCOV -14
(EUL/HS)</es:userLabel>下
的serviceOffset2dEcno。具
体映射规则如下:
SET UINTERFREQHOCOV -14 [HUAWEI]InterFreqHThd2DE
cN0=[E///]
(usedFreqThresh2dEcno+ser
viceOffset2dEcno)
E/// <es:userLabel>Interact.
PS
(64/64)</es:userLabel>servi
ceOffset2dEcno。
[E///]
(usedFreqThresh2dEcno+ser
viceOffset2dEcno+usedFreq
RelThresh2fEcno)<-24,
SET UINTERFREQHOCOV -12
[HUAWEI]InterFreqR99PsTh
d2FEcN0=-24;
:
[HUAWEI]InterFreqR99PsTh
d2FEcN0=[E///]
(usedFreqThresh2dEcno+ser
viceOffset2dEcno+usedFreq
RelThresh2fEcno)
[HUAWEI]InterFreqHThd2FE
cN0=[E///]
SET UINTERFREQHOCOV -12
(usedFreqThresh2dEcno+ser
viceOffset2dEcno+usedFreq
RelThresh2fEcno)
使用E///
<es:userLabel>Conv. CS
speech 12.2 ,
preconfigured</es:userLabel
>下的serviceOffset2dRscp。
如果[E///]
(usedFreqThresh2dRscp+ser
SET UINTERFREQHOCOV -95 viceOffset2dRscp)<-115,则
[HUAWEI]InterFreqCSThd2D
RSCP=-115;
否则:
[HUAWEI]InterFreqCSThd2D
RSCP=[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp)
使用E///
<es:userLabel>Conv. CS
speech 12.2 ,
preconfigured</es:userLabel
>下的serviceOffset2dRscp。
如果[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp+usedFreq
SET UINTERFREQHOCOV -92 RelThresh2fRscp)<-113,则
[HUAWEI]InterFreqCSThd2F
RSCP=-113;
否则:
[HUAWEI]InterFreqCSThd2F
RSCP=[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp+usedFreq
RelThresh2fRscp)
使用E///
<es:userLabel>Interact. PS
(64/64)</es:userLabel>下的
serviceOffset2dRscp。
如果[E///]
(usedFreqThresh2dRscp+ser
SET UINTERFREQHOCOV -95 viceOffset2dRscp)<-115,则
[HUAWEI]InterFreqR99PsTh
d2DRSCP=-115;
否则:
[HUAWEI]InterFreqR99PsTh
d2DRSCP=[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp)
如果E///禁止H异频异系统
切换(由
licence“IfIratMobilityHsdpaE
ul”控制),则
[HUAWEI]InterFreqHThd2DR
SCP=-115;
如果E///未禁止H异频异系
统切换(由
licence“IfIratMobilityHsdpaE
SET UINTERFREQHOCOV -95 ul”控制),映射策略如下:使
用E///
<es:userLabel>Interact. PS
(EUL/HS)</es:userLabel>下
的serviceOffset2dRscp。具
体映射规则如下:
[HUAWEI]InterFreqHThd2DR
SCP=[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp)
使用E///
<es:userLabel>Interact. PS
(64/64)</es:userLabel>下的
serviceOffset2dRscp。
如果[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp+usedFreq
SET UINTERFREQHOCOV -92 RelThresh2fRscp)<-113,则
[HUAWEI]InterFreqR99PsTh
d2FRSCP=-113;
否则:
[HUAWEI]InterFreqR99PsTh
d2FRSCP=[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp+usedFreq
RelThresh2fRscp)
如果E///禁止H异频异系统
切换(由
licence“IfIratMobilityHsdpaE
ul”控制),则
[HUAWEI]InterFreqHThd2FR
SCP=-115;
如果E///未禁止H异频异系
统切换(由
licence“IfIratMobilityHsdpaE
SET UINTERFREQHOCOV -92 ul”控制),映射策略如下:使
用E///
<es:userLabel>Interact. PS
(EUL/HS)</es:userLabel>下
的serviceOffset2dRscp。具
体映射规则如下:
[HUAWEI]InterFreqHThd2FR
SCP=[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp+usedFreq
RelThresh2fRscp)
[HUAWEI]TrigTime2D=D(mi
n([E///]timeToTrigger2dEcn
SET UINTERRATHOCOV D320 o,
[E///]timeToTrigger2dRscp))
[HUAWEI]TrigTime2F=D(min
SET UINTERRATHOCOV D1280 ([E///]timeToTrigger2fEcno,
[E///]timeToTrigger2fRscp))
SET UINTERRATHOCOV -14
使用 <es:userLabel>Conv.
CS speech 12.2 ,
preconfigured</es:userLabel
>下的
serviceOffset2dEcno,
如果
usedFreqThresh2dEcno+ser
viceOffset2dEcno+usedFreq
SET UINTERRATHOCOV -12 RelThresh2fEcno<-24,则
[HUAWEI]InterRATCSThd2FE
cN0=-24;
否则
[HUAWEI]InterRATCSThd2FE
cN0=[E///]
(usedFreqThresh2dEcno+ser
viceOffset2dEcno+usedFreq
RelThresh2fEcno)
SET UINTERRATHOCOV -15
如果E///禁止H异频异系统
切换(由
licence“IfIratMobilityHsdpaE
ul”控制),则
[HUAWEI]InterRATHThd2DE
cN0=-24;
如果E///未禁止H异频异系
统切换(由
licence“IfIratMobilityHsdpaE
ul”控制),映射策略如下:使
用E///
SET UINTERRATHOCOV -15 <es:userLabel>Interact. PS
(EUL/HS)</es:userLabel>下
的serviceOffset2dEcno。
如果[E///]
(usedFreqThresh2dEcno+ser
viceOffset2dEcno)<-24,则
[HUAWEI]InterRATHThd2DE
cN0=-24;
否则:
[HUAWEI]InterRATHThd2DE
cN0=[E///]
(usedFreqThresh2dEcno+ser
viceOffset2dEcno)
使用E///
<es:userLabel>Interact. PS
(64/64)</es:userLabel>下的
serviceOffset2dEcno。
如果[E///]
(usedFreqThresh2dEcno+ser
viceOffset2dEcno+usedFreq
SET UINTERRATHOCOV -13 RelThresh2fEcno)<-24,则
[HUAWEI]InterRATR99PsThd
2FEcN0=-24;
否则:
[HUAWEI]InterRATR99PsThd
2FEcN0=[E///]
(usedFreqThresh2dEcno+ser
viceOffset2dEcno+usedFreq
RelThresh2fEcno)
SET UINTERRATHOCOV -13
E/// <es:userLabel>Conv. CS
speech 12.2 ,
preconfigured</es:userLabel
>下的serviceOffset2dRscp。
[E///]
(usedFreqThresh2dRscp+ser
SET UINTERRATHOCOV -100 viceOffset2dRscp)<-115,则
[HUAWEI]InterRATCSThd2D
RSCP=-115;
HUAWEI]InterRATCSThd2DR
SCP=[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp)
E/// <es:userLabel>Conv. CS
speech 12.2 ,
preconfigured</es:userLabel
>下的serviceOffset2dRscp。
[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp+usedFreq
RelThresh2fRscp)<-113,则
SET UINTERRATHOCOV -97 [HUAWEI]InterRATCSThd2FR
SCP=-113;
:
[HUAWEI]InterRATCSThd2FR
SCP=[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp+usedFreq
RelThresh2fRscp)
SET UINTERRATHOCOV -110
如果E///禁止H异频异系统
切换(由
licence“IfIratMobilityHsdpaE
ul”控制),则
[HUAWEI]InterRATHThd2DR
SCP=-115;
如果E///未禁止H异频异系
统切换(由
licence“IfIratMobilityHsdpaE
ul”控制),映射策略如下:使
用E///
SET UINTERRATHOCOV -110 <es:userLabel>Interact. PS
(EUL/HS)</es:userLabel>下
的serviceOffset2dRscp。
如果[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp)<-115,则
[HUAWEI]InterRATHThd2DR
SCP=-115;
否则:
[HUAWEI]InterRATHThd2DR
SCP=[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp)
使用E///
<es:userLabel>Interact. PS
(64/64)</es:userLabel>下的
serviceOffset2dRscp。
如果[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp+usedFreq
SET UINTERRATHOCOV -107 RelThresh2fRscp)<-113,则
[HUAWEI]InterRATR99PsThd
2FRSCP=-113;
否则:
[HUAWEI]InterRATR99PsThd
2FRSCP=[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp+usedFreq
RelThresh2fRscp)
如果E///禁止H异频异系统
切换(由
licence“IfIratMobilityHsdpaE
ul”控制),则
[HUAWEI]InterRATHThd2FR
SCP=-115;
如果E///未禁止H异频异系
统切换(由
licence“IfIratMobilityHsdpaE
ul”控制),映射策略如下:使
用E///
<es:userLabel>Interact. PS
SET UINTERRATHOCOV -107 (EUL/HS)</es:userLabel>下
的serviceOffset2dRscp。
如果[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp+usedFreq
RelThresh2fRscp)<-115,则
[HUAWEI]InterRATHThd2DR
SCP=-115;
否则:
[HUAWEI]InterRATHThd2DR
SCP=[E///]
(usedFreqThresh2dRscp+ser
viceOffset2dRscp+usedFreq
RelThresh2fRscp)
SET UINTERRATHOCOV 16
SET UINTERRATHOCOV 16
If [E ///] gsmThresh3a <-110,
[HUAWEI] TargetRatHThd =
0;
If [E ///] gsmThresh3a> -48,
SET UINTERRATHOCOV 16 [HUAWEI] TargetRatHThd =
63;
Otherwise: [HUAWEI]
TargetRatHThd = [E ///]
gsmThresh3a + 111,
SET UINTRAFREQHO 6
SET UINTRAFREQHO 6
SET UINTRAFREQHO 6
SET UINTRAFREQHO 12
SET UINTRAFREQHO 12
SET UINTRAFREQHO 12
SET UINTRAFREQHO 0
SET UINTRAFREQHO 0
SET UINTRAFREQHO 8
Huawei E///
D0 0
D10 1
D20 2
D40 3
D60 4
D80 5
D100 6
SET UINTRAFREQHO D320 D120 7
D160 8
D200 9
D240 10
D320 11
D640 12
D1280 13
D2560 14
D5000 15
Huawei E///
D0 0
D10 1
D20 2
D40 3
D60 4
D80 5
D100 6
SET UINTRAFREQHO D640 D120 7
D160 8
D200 9
D240 10
D320 11
D640 12
D1280 13
D2560 14
D5000 15
SET UINTRAFREQHO D640
SET UINTRAFREQHO D4000
SET UINTRAFREQHO D4000
SET UINTRAFREQHO 8
SET UINTRAFREQHO D640
ADD UCELLINTRAFREQHO D4000
ADD UCELLINTRAFREQHO D4000
ADD UCELLINTRAFREQHO 8
ADD UCELLINTRAFREQHO D640
Use <es: userLabel>:
serviceOffset2dEcno
<userLabel / es> under,
Conv CS speech 12.2,
ADD preconfigured.
UCELLINTERFREQHOCOV -12 The [HUAWEI]
TargetFreqCsThdEcN0 =
[E ///]
(NonUsedFreqThresh4_2bEc
no + serviceOffset2dEcno)
If E /// prohibit H-system
inter-frequency handover,
the proposed target cell
threshold parameter to 0dB;
If E /// allow H-system
inter-frequency switching,
use E /// value, namely:
Use <es: userLabel>:
ADD -12 serviceOffset2dEcno
UCELLINTERFREQHOCOV <userLabel / es> under,
Interact PS (EUL / HS).
The [HUAWEI]
TargetFreqHThdEcN0 =
[E ///]
(NonUsedFreqThresh4_2bEc
no + serviceOffset2dEcno)
Use <es: userLabel>:
serviceOffset2dEcno
<userLabel / es> under,
ADD Interact PS (64/64).
-12 The [HUAWEI]
UCELLINTERFREQHOCOV TargetFreqR99PsThdEcN0 =
[E ///]
(NonUsedFreqThresh4_2bEc
no + serviceOffset2dEcno)
Use <es: userLabel>:
serviceOffset2dRscp
<userLabel / es> under,
Conv CS speech 12.2,
ADD preconfigured.
UCELLINTERFREQHOCOV -92 The [HUAWEI]
TargetFreqCsThdRscp =
[E ///]
(NonUsedFreqThresh4_2bRs
cp + serviceOffset2dRscp)
If E /// prohibit H-system
inter-frequency handover,
the proposed target cell
threshold parameter to
-25dB;
If E /// allow H-system
inter-frequency switching,
use E /// value, namely:
Use <es: userLabel>:
ADD
UCELLINTERFREQHOCOV -92 serviceOffset2dRscp
<userLabel / es> under,
Interact PS (EUL / HS).
The [HUAWEI]
TargetFreqHThdRscp =
[E ///]
(NonUsedFreqThresh4_2bRs
cp + serviceOffset2dRscp)
Use <es: userLabel>:
serviceOffset2dRscp
<userLabel / es> under,
ADD Interact PS (64/64).
-92 The [HUAWEI]
UCELLINTERFREQHOCOV TargetFreqR99PsThdRscp =
[E ///]
(NonUsedFreqThresh4_2bRs
cp + serviceOffset2dRscp)
For low
speed(5km/h):Range is
D4~D6, the recommended
value is D5;
for middle
speed(50km/h):Range is
ADD D3~D4, the recommended
value is D4; use E/// value
UCELLINTERFREQHONCOV for high
speed(120km/h):Range is
D2~D4, the recommended
value is D2;
universal value:Range is
D3~D6, the recommended
value is D3.
SET UCORRMALGOSWITCH 1
SET UCORRMALGOSWITCH 1
use E/// value,
ADD U2GNCELL 0 “vsDataGsmRelation”Qoffse
t1sn。
ADD UCELLINTRAFREQHO 3 use E/// value
ADD UCELLSELRESEL 2 Huawei<==>E/2
ADD UCELLSELRESEL 1 Huawei<==>E/2
Huawei E///
CHIP0 0
CHIP256 1
CHIP512 2
CHIP768 3
ADD UCELLSETUP None CHIP1024 4
CHIP1280 5
CHIP1536 6
CHIP1792 7
CHIP2048 8
CHIP2304 9
ADD UCELLSETUP None
ADD UCELLSETUP
ADD
UCELLINTERFREQHOCOV 4 use E/// value
ADD
UCELLINTERFREQHOCOV 4 use E/// value
ADD UCELLINTERRATHOCOV 4 use E/// value
ADD UCELLINTERRATHOCOV 4 use E/// value
ADD UCELLINTRAFREQHO D640
SET UINTERFREQHOCOV 4
SET UINTERFREQHOCOV 4
SET UINTERRATHOCOV 4
SET UINTERRATHOCOV 4
SET UINTRAFREQHO D3 use E/// value
SET UINTRAFREQHO CPICH_EC/NO
SET UINTERFREQHOCOV 4
SET UINTERFREQHOCOV 0
SET UINTERFREQHOCOV D0
ms
SET UINTERFREQHOCOV -12
SET UINTERFREQHOCOV 1
SET UINTERRATHOCOV 4
SET UINTERRATHOCOV 1
HW = E / 5, the original
network parameters
ADD UCELLSETUP 0 "vsDataUtranCell" tab page
accessible.
ADD UCELLSELRESEL 2
ADD UCELLSELRESEL 1
ADD UCELLSELRESEL 5
4
ADD UCELLSELRESEL
ADD UCELLINTRAFREQHO 0
D1024 BEF2HTVMTHD take greater
SET UUESTATETRANS than a threshold level
R14之后:D256 D2F2PTVMTHD
SET URRCTRLSWITCH 0
SET UCORRMPARA 0
SET UCORRMPARA 0
ADD UCELLRLACTTIME 5
SET UCORRMALGOSWITCH 0
SET UQOSACT NO
SET UDCCC D8
RAB业务索引41-93(PS域
交互和背景类各种速率的
ADD UTYPRABRLC RAB),“TRCHTYPE=TRCH
_HSDSCH,
OPPOSITETRCHTYPE=TRCH_
DCH”的 TIMERRST为D450
SET UCORRMPARA 0
SET UDPUCFGDATA
SET URRCTRLSWITCH ON
SET URRCTRLSWITCH 0
SET UCORRMALGOSWITCH 1
SET USTATETIMER 5000
SET USTATETIMER 4
SET UCORRMALGOSWITCH 0
ADD UCELLHSDPCCH D2
ADD UCELLHSDPCCH 1
ADD UCELLHSDPCCH 1
SET UALGORSVPARA 0
SET UFRCCHLTYPEPARA 0
SET UCORRMALGOSWITCH 1
SET UCORRMALGOSWITCH
0
SET USTATETIMER 300
SET URRCTRLSWITCH 0
SET UNBMPARA 1
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
Huawei parameters
CS_RL_SETUP_SWITCH = 1
or PS_RL_SETUP_SWITCH =
1, recommended that this
SET URRCTRLSWITCH 0 parameter is set to 1, if
CS_RL_SETUP_SWITCH = 0
and PS_RL_SETUP_SWITCH
= 0, this parameter is set to
baseline.
Huawei parameters
CS_RL_SETUP_SWITCH = 1
or PS_RL_SETUP_SWITCH =
1, recommended that this
SET URRCTRLSWITCH 0 parameter is set to 1, if
CS_RL_SETUP_SWITCH = 0
and PS_RL_SETUP_SWITCH
= 0, this parameter is set to
baseline.
Huawei parameters
CS_RL_SETUP_SWITCH = 1
or PS_RL_SETUP_SWITCH =
1, recommended that this
SET UCONNMODETIMER 3 parameter is set to 3, if
CS_RL_SETUP_SWITCH = 0
and PS_RL_SETUP_SWITCH
= 0, this parameter is set to
baseline.
Huawei parameters
CS_RL_SETUP_SWITCH = 1
or PS_RL_SETUP_SWITCH =
1, recommended that this
SET UCONNMODETIMER D1 parameter is set to D20, if
CS_RL_SETUP_SWITCH = 0
and PS_RL_SETUP_SWITCH
= 0, this parameter is set to
baseline.
ADD UCELLSETUP 50 2015删除
ADD UCELLSETUP 5 2015删除
If RncFeature include in
DirectUpswitchUra,
SET URRCTRLSWITCH corresponding featureState
0 = ACTIVATED, then
RNC_TVM_BASED_P2D_SWI
TCH = 1; otherwise = 0;
LOOSE_CAC
ADD UCELLALGOSWITCH LOOSE_CAC
SET UCACALGOSWITCH 0
ADD UCELLALGOSWITCH 0
ADD UCELLALGOSWITCH 0
ADD UCELLALGOSWITCH 0
ADD UCELLALGOSWITCH ALGORITHM_SECOND
SET UFRC 1
SET UFRC 0
ADD 0
UCELLINTERFREQHOCOV
ADD
UCELLINTERFREQHOCOV 0
ADD UCELLINTERRATHOCOV 60 s
ADD UCELLINTERRATHOCOV 0
ADD UCELLINTERRATHOCOV D1000
ADD UCELLINTERRATHOCOV 0
SET UCORRMPARA 1
SET UQUEUEPREEMPT OFF
SET UQUEUEPREEMPT:
PreemptEnhSwitch=PREEMP
0
T_ENH_CSRRC_PREEMPT_PS
_SWITCH-1;
SET UQUEUEPREEMPT:
PreemptEnhSwitch=
PREEMPT_ENH_CSRAB_PRE 0
EMPT_PS_SWITCH-1;
SET UQUEUEPREEMPT 1
ADD UCELLALGOSWITCH 0
SET UQUEUEPREEMPT:
CsP2DPreemptSwitch=ON; OFF
IF [E///]qRxLevMin (MO
Class
Name:vsDataUtranCell)<-
ADD UCELLSELRESEL 0 115,
[HUAWEI]QrxlevminExtSup(
MML:ADD
UCELLSELRESEL)=TRUE
IF [E ///] qRxLevMin (MO
Class Name:
vsDataUtranCell) <- 115,
[HUAWEI] DeltaQrxlevmin
(MML: ADD UCELLSELRESEL)
ADD UCELLSELRESEL None = ([E ///] qRxLevMin (MO
Class Name:
vsDataUtranCell) +115) / 2
This parameter is not
configured ELSE
SET URRCTRLSWITCH 0
SET UCORRMPARA 0
SET ULDCALGOPARA 60
SET ULDCALGOPARA 60
SET UCORRMALGOSWITCH 0
SET UCORRMALGOSWITCH 0
SET UHSDPCCH D20
OFF
SET URRCTRLSWITCH
SET UCORRMALGOSWITCH 0
Characteristics of the
switching follows the
mapping rules, please refer
to the specific
characteristics of the
opening parameters
Manual:
If [E ///]
featureStateFDpchSrbOnHsd
pa == 1 (while
DCH(DCH,DCH) NodeBFunction ::
SET UFRCCHLTYPEPARA licenseStateFDpchSrbOnHsd
pa = ENABLED), then
[HUAWEI] SrbChlType =
HSPA, also set SET
UCORRMPARA:
PerfEnhanceSwitch =
PERFENH_SRB_OVER_HSUP
A_TTI10_SWITCH-1;
Otherwise [HUAWEI]
SrbChlType = DCH
SET UCORRMALGOSWITCH 0
SET UCORRMALGOSWITCH 0
ADD UOPERUSERGBR
D64
MOD UOPERUSERGBR
ADD UOPERUSERGBR
D64
MOD UOPERUSERGBR
SET URRCTRLSWITCH 0
ADD URACH
MOD URACH 10
ADD URACH
MOD URACH 0
ADD
60
UCELLINTERFREQHOCOV
ADD UCELLALGOSWITCH 0
SET UALGORSVPARA 0
1
MOD UCELLCAC
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET URRCTRLSWITCH 0
SET UPSINACTTIMER 4
SET UCONNMODETIMER
INVALID
SET UPSINACTTIMER
SET UCORRMALGOSWITCH BasedOnUECap 2015删除
SET UCORRMALGOSWITCH:
SET UCORRMALGOSWITCH CmpSwitch2=CMP_F2D_RLC
0 _ONESIDE_REBUILD_SWITC
H-1;
SET UCORRMALGOSWITCH:
SET UCORRMALGOSWITCH CmpSwitch=CMP_D2F_RLC_
0
ONESIDE_REBUILD_SWITCH-
1;
SET UFRC:
RetryCapability=TTI_2MS-0;
SET UCORRMALGOSWITCH:
DraSwitch2=DRA_PCPICH_E
CN0_ON_RACH_UPDATE_S
WITCH-1;
SET UCORRMPARA:
PerfEnhanceSwitch=PERFEN
H_HSUPA_TTI_RECFG_PROC
_OPT_SWITCH-1;
SET UCORRMALGOSWITCH:
SET ReservedSwitch0=RESERVED
_SWITCH_0_BIT30-1;
UCORRMALGOSWITCH(R1
(R13/14)
3/14) SET
SET UNBMPARA:PerfEnhanceSwi
UNBMPARA(R15/R16) tch=PERFENH_HRNTI_OPT_S
WITCH-1; (R15/R16)
MOD UCELLHSDPA:
CellId=XX, HspaPower=0;
If the original network open
SRB OE, recommends the
implementation of the
following parameters.
//打开RAB DRD阶段限制 // Open RAB DRD stage
SRB承载信道D2H算法开关 restrictions SRB bearer
SET UCORRMALGOSWITCH: channel D2H algorithm
CmpSwitch2=CMP_DRD_SR switch
BOVERH_SWITCH-1; SET UCORRMALGOSWITCH:
CmpSwitch2 =
//打开RAB DRD流程结束后 CMP_DRD_SRBOVERH_SWIT
SRB承载信道由DCH快速重 CH-1;
试到E-DCH算法开关 // Open end of the process
SET UCORRMPARA: after RAB DRD SRB bearer
PerfEnhanceSwitch1=PERFE channel by the DCH quickly
NH_SRB_FAST_HRETRY_AFT retry algorithm switch to E-
ER_DRD_SWITCH-1; DCH
SET UCORRMPARA:
PerfEnhanceSwitch1 =
PERFENH_SRB_FAST_HRETR
Y_AFTER_DRD_SWITCH-1;
SET UUESTATETRANSTIMER 10
SET URRCTRLSWITCH
0
SET URRCTRLSWITCH 0
SET
SET UCONNMODETIMER 5 UCONNMODETIMER:T309=8
;
SET URRCTRLSWITCH
0
SET UDPUCFGDATA
0
SET UCORRMALGOSWITCH 1
Direct use E /// original
ADD UEXT3GCELL -18 network value
IF [E///]qRxLevMin (MO
Class
Name:vsDataExternalGsmCe
ll)==100,
[HUAWEI]qRxLevMin=([E///]
qRxLevMin (MO Class
ADD UEXT3GCELL -58 Name:vsDataUtranCell)
+115)/2-58;
ELSE
[HUAWEI]qRxLevMin=([E///]
qRxLevMin (MO Class
Name:vsDataExternalGsmCe
ll) + 115)/2 - 58
HW = E / 5, the original
network parameters
ADD UEXT2GCELL 0
"vsDataUtranCell" tab page
accessible.
HW = E / 5, the original
network parameters
ADD UEXT3GCELL 0 "vsDataUtranCell" tab page
accessible.
ADD UINTERFREQNCELL
0 2015删除
ADD UINTRAFREQNCELL
0 2015删除
ADD UINTRAFREQNCELL
0 使用Huawei基线
ADD UINTRAFREQNCELL
0 使用Huawei基线
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
FALSE(OR True),FALSE(OR
True),FALSE(OR
Specifies which access True),FALSE(OR
classes are barred for the True),FALSE(OR
feature Cell Level Access True),FALSE(OR
Class Barring. True),FALSE(OR
Each boolean in the True),FALSE(OR
accessClassNBarred sequence represents one True),FALSE(OR
access class. The access class True),FALSE(OR
is restricted by setting the True),FALSE(OR
boolean to TRUE ('barred'), True),FALSE(OR
otherwise the boolean is set True),FALSE(OR
to True),FALSE(OR
True),FALSE(OR
True),FALSE(OR True)
Maximum number of
preambleRetransMax preambles in one preamble 1..64
ramping cycle.
Capability information
indicating if F-DPCH is
fdpchSupport supported in the cell as DEACTIVATED = 0
reported by RBS in RSI and ACTIVATED = 1
Audit response.
hsDschRcLostT:
Controls the RCS timer for
supervision of uplink synch
of RLS containing the serving
HS-DSCH radio link.
Special values:
18000 indicates that the RCS
function is switched off.
Used for test purposes
Special values:
0 is used to turn off the use
of this timer, meaning that
the packet part of the
connection will not be
downswitched or released
due to PS inactivity.
Value mapping:
1 : 0.5 s
...
60 : 30 s
...
180 : 90 s
Minimum required
(acceptable) RX level in the
cell.
Used in UE functions for cell
selection/reselection in idle
mode and connected mode.
Value launched by System
information (SIB11) for each
intra-frequency
measurement object
corresponding to adjacent
qRxLevMin (MO Class
cells of serving cell.
Name:vsDataExternalGsmCe -115..-25,100..100
ll)
Special values:
100: Indicates that the
minimum Rx level has not
been specified by the
operator. The parameter is
then not
present in SIB11 for this
neighbor. The UE will use
the serving cell value
(UtranCell MO value)
instead
Control of cell
selection/reselection. Time-
to-trigger for cell
reselection.
treSelection Value launched by System 0..31
information (SIB3).
Unit: s
Used in UE functions for cell
selection/reselection in idle
mode and connected mode.
qQualMin Minimum required
(MO Class -24..0
Name:vsDataUtranCell) (acceptable) quality level in
the cell.
Unit: dB
Minimum required
(acceptable) quality level in
the cell (dB). Used to set cell
border between two cells.
Used in UE functions for cell
selection/reselection in idle
mode and connected mode.
qQualMin Special values:
(MO Class
Name:vsDataExternalUtranC 100: Indicates that the -24..0,100..100
minimum quality level has
ell) not been specified by the
operator. The parameter is
then not
present in SIB11 for this
neighbor. The UE will use
the serving cell value
(UtranCell MO value)
instead
Minimum required
(acceptable) quality level in
the cell (dB). Used to set cell
border between two cells.
Used in UE functions for cell
qQualMin selection/reselection in idle -24..0
mode and connected mode.
Special values:
100: Indicates that the
minimum quality level h
The decision on when
measurements on intra-
sIntraSearch frequencies shall be 0..27
performed
The decision on when
measurements on inter-
sInterSearch frequencies shall be 0..27
performed
The decision on when
measurements on GSM
frequencies shall be
performed is made using
this parameter in relation
with Squal.
sRatSearch If S_qual > this parameter, -32..20
UE need not perform
measurements on GSM
cells.
If S_qual <= this parameter,
UE shall perform meas
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dEcno:
usedFreqThresh2dEcno+ser is Ec/No. -24..0
viceOffset2dEcno
serviceOffset2dEcno: serviceOffset2dEcno:
Service-specific offset for -20..20
event 2d when the
measurement quantity is
CPICH Ec/No
Time between detection of
event 2d and sending of the
measurement report, when
the measurement quantity 0..0 10..10 20..20 40..40
is CPICH EC/NO. 60..60 80..80 100..100
timeToTrigger2dEcno,timeT Special values: 120..120 160..160 200..200
oTrigger2dRscp When the value 5000 is set, 240..240 320..320 640..640
the Measurement Control 1280..1280 2560..2560
message will not be sent at 5000..5000
all.
Unit: ms
Change takes effect: Ongo
Time between detection of
event 2d and sending of the
measurement report, when
the measurement quantity 0..0 10..10 20..20 40..40
is CPICH EC/NO. 60..60 80..80 100..100
timeToTrigger2fEcno,timeTo Special values: 120..120 160..160 200..200
Trigger2fRscp When the value 5000 is set, 240..240 320..320 640..640
the Measurement Control 1280..1280 2560..2560
message will not be sent at 5000..5000
all.
Unit: ms
Change takes effect: Ongo
Time between detection of
timeToTrigger3a event 3a and sending of the 0..15
measurement report
Time between detection of
timeToTrigger3a event 3a and sending of the 0..15
measurement report
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dEcno:
is Ec/No. -24..0
usedFreqThresh2dEcno+ser
viceOffset2dEcno
serviceOffset2dEcno: serviceOffset2dEcno:
Service-specific offset for -20..20
event 2d when the
measurement quantity is
CPICH Ec/No
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dEcno:
is Ec/No. -24..0
usedFreqThresh2dEcno+ser
viceOffset2dEcno
serviceOffset2dEcno: serviceOffset2dEcno:
Service-specific offset for -20..20
event 2d when the
measurement quantity is
CPICH Ec/No
usedFreqThresh2dRscp:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dRscp:
is RSCP -115..-25
usedFreqThresh2dRscp+serv
iceOffset2dRscp
serviceOffset2dRscp: serviceOffset2dRscp:
Service-specific offset for -50..50
event 2d when the
measurement quantity is
RSCP
Threshold for event 3a for
GSM. Range is valid for GSM
carrier RSSI.
Unit: 0.5 dB
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity
is Ec/No.
usedFreqThresh2dEcno:
serviceOffset2dEcno: -24..0
usedFreqThresh2dEcno+ser Service-specific offset for
viceOffset2dEcno+usedFreq event 2d when the serviceOffset2dEcno:
RelThresh2fEcno measurement quantity is -20..20
CPICH Ec/No
usedFreqRelThresh2fEcno:
usedFreqRelThresh2fEcno: 0..20
Relative threshold for event
2f versus event 2d for the
used frequency when the
measurement quantity is
CPICH Ec/No
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dEcno:
is Ec/No. -24..0
usedFreqThresh2dEcno+ser
viceOffset2dEcno
serviceOffset2dEcno: serviceOffset2dEcno:
Service-specific offset for -20..20
event 2d when the
measurement quantity is
CPICH Ec/No
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dEcno:
is Ec/No. -24..0
usedFreqThresh2dEcno+ser
viceOffset2dEcno
serviceOffset2dEcno: serviceOffset2dEcno:
Service-specific offset for -20..20
event 2d when the
measurement quantity is
CPICH Ec/No
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity
is Ec/No.
usedFreqThresh2dEcno:
serviceOffset2dEcno: -24..0
usedFreqThresh2dEcno+ser Service-specific offset for
viceOffset2dEcno+usedFreq event 2d when the serviceOffset2dEcno:
RelThresh2fEcno measurement quantity is -20..20
CPICH Ec/No.
usedFreqRelThresh2fEcno:
usedFreqRelThresh2fEcno: 0..20
Relative threshold for event
2f versus event 2d for the
used frequency when the
measurement quantity is
CPICH Ec/No
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity
is Ec/No.
usedFreqThresh2dEcno:
serviceOffset2dEcno: -24..0
usedFreqThresh2dEcno+ser Service-specific offset for
viceOffset2dEcno+usedFreq event 2d when the serviceOffset2dEcno:
RelThresh2fEcno measurement quantity is -20..20
CPICH Ec/No.
usedFreqRelThresh2fEcno:
usedFreqRelThresh2fEcno: 0..20
Relative threshold for event
2f versus event 2d for the
used frequency when the
measurement quantity is
CPICH Ec/No
usedFreqThresh2dRscp:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dRscp:
usedFreqThresh2dRscp+serv is RSCP. -115..-25
iceOffset2dRscp
serviceOffset2dRscp: serviceOffset2dRscp:
Service-specific offset for -50..50
event 2d when the
measurement quantity is
RSCP
usedFreqThresh2dRscp:
Threshold for event 2d for
the used frequency when
the measurement quantity
is RSCP.
usedFreqThresh2dRscp:
serviceOffset2dRscp: -115..-25
usedFreqThresh2dRscp+serv Service-specific offset for
iceOffset2dRscp+usedFreqR event 2d when the serviceOffset2dRscp:
elThresh2fRscp measurement quantity is -50..50
RSCP.
usedFreqRelThresh2fRscp:
usedFreqRelThresh2fRscp: 0..20
Relative threshold for event
2f versus event 2d for the
used frequency when the
measurement quantity is
RSCP
usedFreqThresh2dRscp:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dRscp:
usedFreqThresh2dRscp+serv is RSCP. -115..-25
iceOffset2dRscp
serviceOffset2dRscp: serviceOffset2dRscp:
Service-specific offset for -50..50
event 2d when the
measurement quantity is
RSCP
usedFreqThresh2dRscp:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dRscp:
usedFreqThresh2dRscp+serv is RSCP. -115..-25
iceOffset2dRscp
serviceOffset2dRscp: serviceOffset2dRscp:
Service-specific offset for -50..50
event 2d when the
measurement quantity is
RSCP
usedFreqThresh2dRscp:
Threshold for event 2d for
the used frequency when
the measurement quantity
is RSCP.
usedFreqThresh2dRscp:
serviceOffset2dRscp: -115..-25
usedFreqThresh2dRscp+serv Service-specific offset for
iceOffset2dRscp+usedFreqR event 2d when the serviceOffset2dRscp:
elThresh2fRscp measurement quantity is -50..50
RSCP.
usedFreqRelThresh2fRscp:
usedFreqRelThresh2fRscp: 0..20
Relative threshold for event
2f versus event 2d for the
used frequency when the
measurement quantity is
RSCP
usedFreqThresh2dRscp:
Threshold for event 2d for
the used frequency when
the measurement quantity
is RSCP.
usedFreqThresh2dRscp:
serviceOffset2dRscp: -115..-25
usedFreqThresh2dRscp+serv Service-specific offset for
iceOffset2dRscp+usedFreqR event 2d when the serviceOffset2dRscp:
elThresh2fRscp measurement quantity is -50..50
RSCP.
usedFreqRelThresh2fRscp:
usedFreqRelThresh2fRscp: 0..20
Relative threshold for event
2f versus event 2d for the
used frequency when the
measurement quantity is
RSCP
Time between detection of
event 2d and sending of the
measurement report, when
0..0 10..10 20..20 40..40
the measurement quantity 60..60 80..80 100..100
is CPICH EC/NO.
timeToTrigger2dEcno,timeT 120..120 160..160 200..200
oTrigger2dRscp Special values: 240..240 320..320 640..640
When the value 5000 is set,
the Measurement Control 1280..1280 2560..2560
5000..5000
message will not be sent at
all.
Change takes effect: Ongo
Time between detection of
event 2d and sending of the
measurement report, when
the measurement quantity 0..0 10..10 20..20 40..40
is CPICH EC/NO. 60..60 80..80 100..100
timeToTrigger2fEcno,timeTo Special values: 120..120 160..160 200..200
Trigger2fRscp When the value 5000 is set, 240..240 320..320 640..640
the Measurement Control 1280..1280 2560..2560
message will not be sent at 5000..5000
all.
Unit: ms
Change takes effect: Ongo
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dEcno:
is Ec/No. -24..0
usedFreqThresh2dEcno+ser
viceOffset2dEcno
serviceOffset2dEcno: serviceOffset2dEcno:
Service-specific offset for -20..20
event 2d when the
measurement quantity is
CPICH Ec/No
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity
is Ec/No.
usedFreqThresh2dEcno:
serviceOffset2dEcno: -24..0
usedFreqThresh2dEcno+ser Service-specific offset for
viceOffset2dEcno+usedFreq event 2d when the serviceOffset2dEcno:
RelThresh2fEcno measurement quantity is -20..20
CPICH Ec/No.
usedFreqRelThresh2fEcno:
usedFreqRelThresh2fEcno: 0..20
Relative threshold for event
2f versus event 2d for the
used frequency when the
measurement quantity is
CPICH Ec/No
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dEcno:
is Ec/No. -24..0
usedFreqThresh2dEcno+ser
viceOffset2dEcno
serviceOffset2dEcno: serviceOffset2dEcno:
Service-specific offset for -20..20
event 2d when the
measurement quantity is
CPICH Ec/No
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dEcno:
is Ec/No. -24..0
usedFreqThresh2dEcno+ser
viceOffset2dEcno
serviceOffset2dEcno: serviceOffset2dEcno:
Service-specific offset for -20..20
event 2d when the
measurement quantity is
CPICH Ec/No
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity
is Ec/No. usedFreqThresh2dEcno:
-24..0
usedFreqThresh2dEcno+ser serviceOffset2dEcno:
viceOffset2dEcno+usedFreq Service-specific offset for serviceOffset2dEcno:
RelThresh2fEcno event 2d when the -20..20
measurement quantity is
CPICH Ec/No usedFreqRelThresh2fEcno:
0..20
usedFreqRelThresh2fEcno:
Relative threshold for event
2f versus event 2d for the
used frequency when
usedFreqThresh2dEcno:
Threshold for event 2d for
the used frequency when
the measurement quantity
is Ec/No.
usedFreqThresh2dEcno:
serviceOffset2dEcno: -24..0
usedFreqThresh2dEcno+ser Service-specific offset for
viceOffset2dEcno+usedFreq event 2d when the serviceOffset2dEcno:
RelThresh2fEcno measurement quantity is -20..20
CPICH Ec/No.
usedFreqRelThresh2fEcno:
usedFreqRelThresh2fEcno: 0..20
Relative threshold for event
2f versus event 2d for the
used frequency when the
measurement quantity is
CPICH Ec/No
usedFreqThresh2dRscp:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dRscp:
is RSCP. -115..-25
usedFreqThresh2dRscp+serv
iceOffset2dRscp
serviceOffset2dRscp: serviceOffset2dRscp:
Service-specific offset for -50..50
event 2d when the
measurement quantity is
RSCP
usedFreqThresh2dRscp:
Threshold for event 2d for
the used frequency when
the measurement quantity
is RSCP.
usedFreqThresh2dRscp:
serviceOffset2dRscp: -115..-25
usedFreqThresh2dRscp+serv Service-specific offset for
iceOffset2dRscp+usedFreqR event 2d when the serviceOffset2dRscp:
elThresh2fRscp measurement quantity is -50..50
RSCP.
usedFreqRelThresh2fRscp:
usedFreqRelThresh2fRscp: 0..20
Relative threshold for event
2f versus event 2d for the
used frequency when the
measurement quantity is
RSCP
usedFreqThresh2dRscp:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dRscp:
is RSCP. -115..-25
usedFreqThresh2dRscp+serv
iceOffset2dRscp
serviceOffset2dRscp: serviceOffset2dRscp:
Service-specific offset for -50..50
event 2d when the
measurement quantity is
RSCP
usedFreqThresh2dRscp:
Threshold for event 2d for
the used frequency when
the measurement quantity usedFreqThresh2dRscp:
is RSCP. -115..-25
usedFreqThresh2dRscp+serv
iceOffset2dRscp
serviceOffset2dRscp: serviceOffset2dRscp:
Service-specific offset for -50..50
event 2d when the
measurement quantity is
RSCP
usedFreqThresh2dRscp:
Threshold for event 2d for
the used frequency when
the measurement quantity
is RSCP.
usedFreqThresh2dRscp:
serviceOffset2dRscp: -115..-25
usedFreqThresh2dRscp+serv Service-specific offset for
iceOffset2dRscp+usedFreqR event 2d when the serviceOffset2dRscp:
elThresh2fRscp measurement quantity is -50..50
RSCP.
usedFreqRelThresh2fRscp:
usedFreqRelThresh2fRscp: 0..20
Relative threshold for event
2f versus event 2d for the
used frequency when the
measurement quantity is
RSCP
usedFreqThresh2dRscp:
Threshold for event 2d for
the used frequency when
the measurement quantity
is RSCP.
usedFreqThresh2dRscp:
serviceOffset2dRscp: -115..-25
usedFreqThresh2dRscp+serv Service-specific offset for
iceOffset2dRscp+usedFreqR event 2d when the serviceOffset2dRscp:
elThresh2fRscp measurement quantity is -50..50
RSCP.
usedFreqRelThresh2fRscp:
usedFreqRelThresh2fRscp: 0..20
Relative threshold for event
2f versus event 2d for the
used frequency when the
measurement quantity is
RSCP
Threshold for event 3a for
GSM. Range is valid for GSM
carrier RSSI.
Unit: 0.5 dB
Dependencies:
Used when the IE
qOffset1sn "cell_selection_and_reselec -50..50
tion_quality_measure" in
SIB 11/12 is set to "CPICH
RSCP". This is configured
through
UtranCell::qualMeasQuantit
y
Maximum number of cells in
active set.
The reporting deactivation
threshold, used to control
intra-frequency
maxActiveSet measurements (event 1a), is 2..4
set to maxActiveSet - 1.
The replacement activation
threshold, used to control
intra-frequency
measurements (event 1c)
Cell reselection hysteresis
used in UE functions in idle
qHyst1 and connected mode. Value 0..40
launched by System
information (SIB3)
The hysteresis value of the
serving cell.
qHyst2 Used to perform cell ranking 0..40
for the serving cell
Value mapping:
The cycle length
Dependencies:
Used when the IE
qOffset1sn "cell_selection_and_reselec -50..50
tion_quality_measure" in
SIB 11/12 is set to "CPICH
RSCP". This is configured
through
UtranCell::qualMeasQuantit
y
Dependencies:
Used when the IE
qOffset1sn "cell_selection_and_reselec -50..50
tion_quality_measure" in
SIB 11/12 is set to "CPICH
RSCP". This is configured
through
UtranCell::qualMeasQuantit
y
Dependencies:
Changing this attribute may
affect ongoing traffic.
Value mapping:
0: 0.0 dB
1: 0.5 dB
...
29: 14.5 dB
hysteresis2d 0..29
Unit: 0.5 db
Change takes effect:
Ongoing connections (next
time that 2d/2f
measurements are started
or modified)
Hysteresis for event 2f.
Value mapping:
0: 0.0 dB
1: 0.5 dB
...
hysteresis2f 29: 14.5 dB 0..29
Change takes effect:
Ongoing connections (next
time that 2d/2f
measurements are started
or modified)
Hysteresis for event 2d.
Dependencies:
If CN Hard Handover is
supported and
Dependencies:
If CN Hard Handover is
supported and
Value mapping
Weight factor to include
active set cells other than
the best in evaluation
criteria for event 1a.
w1a Used by UE functions for 0..20
intra-frequency
measurement reporting (in
CELL_DCH)
Signal strength offset
between source and target
cells.
Dependencies:
Used when the IE
qOffset1sn "cell_selection_and_reselec -50..50
tion_quality_measure" in
SIB 11/12 is set to "CPICH
RSCP". This is configured
through
UtranCell::qualMeasQuantit
y
Signal strength offset
between source and target
cells. used when the IE
qOffset2sn "cell_selection_and_reselec -50..50
tion_quality_measure" in
SIB 11/22 is set to "CPICH
Ec/No".
Maximum number of cells in
active set.
The reporting deactivation
threshold, used to control
intra-frequency
maxActiveSet measurements (event 1a), is 2..4
set to maxActiveSet - 1.
The replacement activation
threshold, used to control
intra-frequency
measurements (event 1c)
Signal strength offset
between source and target
cells.
Dependencies:
Used when the IE
qOffset1sn "cell_selection_and_reselec -50..50
tion_quality_measure" in
SIB 11/12 is set to "CPICH
RSCP". This is configured
through
UtranCell::qualMeasQuantit
y
Signal strength offset
between source and target
cells. used when the IE
qOffset2sn "cell_selection_and_reselec -50..50
tion_quality_measure" in
SIB 11/22 is set to "CPICH
Ec/No"
Dependencies:
rlFailureT rlFailureT > (nInSyncInd * 10 0..255
ms)
Unit: 0.1 s
None None None
Possible values:
• ACTIVATED
• DEACTIVATED
EDCH_2MS_TTI_NON_CAPA
BLE = 0
EDCH_2MS_TTI_CAPABLE =
1
Shows whether the cell is E-
DCH 2 ms TTI capable or not.
Possible values:
• EDCH_2MS_TTI_CAPABLE
eDch2msTtiCapability •
EDCH_2MS_TTI_NON_CAPA
BLE
Specification: 3GPP TS
25.433, NBAP, UTRAN Iub
interface NBAP signalling
Feature state for licensed
feature 'EUL 2 ms TTI',
indicating if the feature is
ACTIVATED or
DEACTIVATED.
Possible values:
• ACTIVATED
• DEACTIVATED
featureStateEul2msTti Dependencies: Can only be DEACTIVATED = 0
ACTIVATED = 1
set to ACTIVATED in case a
valid license key is installed
for the feature, that is, if
NodeBFunction::licenseState
Eul2msTti = ENABLED. If the
value is ACTIVATED when
the license state changes
from ENABLED to DISABLED
a corresponding License Not
Valid alarm is generated.
Special values:
-1: the value of
ChannelSwitching::inactivity
Timer is used
Number of preconfigured
subsequent transmissions of { 1..5 }
noOfPagingRecordTransm the same Paging Record.
Unit: dB
Unit: Db
Dependencies:
Used when the IE
qOffset1sn "cell_selection_and_reselec -50..50
tion_quality_measure" in
SIB 11/12 is set to "CPICH
RSCP". This is configured
through
UtranCell::qualMeasQuantit
y
Signal strength offset
between source and target
cells. used when the IE
qOffset2sn "cell_selection_and_reselec -50..50
tion_quality_measure" in
SIB 11/22 is set to "CPICH
Ec/No"
70~95 SF32(SF32)
NOT_RESERVED(不保
0(587)/1(645) maping
留),RESERVED
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
0 NOT_BARRED maping
91 maping
160(519)/500(713) 200
[10~96] 96
not found 40
-31 -31 maping
-7 -7 maping
-6 -6 maping
maxFach1Power=18&30/ma
xFach2Power=15&30 use smartRNO mapping maping
-4 -4 maping
8 8 maping
3 3 maping
-27 -27 maping
-4 -4 maping
[1.5,2.5]
80 maping
=(460/350-330/240-80)/10
8 D8 maping
0 (OFF) 0
not found ALLOWED maping
0 (OFF) 0 maping
1(52)/3(576) 3 maping
not found 5,10 maping
4 4 maping
3 D30 maping
dchRcLostT=50 /
hsDschRcLostT=100 11000
64 D32 maping
64 D16 maping
SigChType=DCH_13.6K_SIGN
ALLING
0 0 maping
not found 1
1 (TRUE) 1 maping
20 1
100(957)/-105(1) [-53,-47] maping
2 2 maping
-18 -18 maping
timeToTrigger2dEcno=320/ti
meToTrigger2dRscp=320 D320 maping
timeToTrigger2fEcno=1280/ D1280 maping
timeToTrigger2fRscp=1280
0 0 maping
15 8
timeToTrigger2dEcno=320/ti
meToTrigger2dRscp=320 D320
timeToTrigger2fEcno=1280/ D1280
timeToTrigger2fRscp=1280
usedFreqThresh2dEcno=[-
11]/serviceOffset2dEcno=0 -14
usedFreqThresh2dEcno=[-
11,-
9]/serviceOffset2dEcno=0/u -12
sedFreqRelThresh2fEcno=2
usedFreqThresh2dEcno=[- -14
11]/serviceOffset2dEcno=0
usedFreqThresh2dEcno=[-
16,-
9]/serviceOffset2dEcno=-
2&0 -14
IfIratMobilityHsdpaEul=0&1
(DEACTIVED&ACTIVED)
usedFreqThresh2dEcno=[-
11,- -12
9]/serviceOffset2dEcno=0/u
sedFreqRelThresh2fEcno=2
usedFreqThresh2dEcno=[-
16,-
9]/serviceOffset2dEcno=-
2&0 -12
IfIratMobilityHsdpaEul=0&1
(DEACTIVED&ACTIVED)
usedFreqThresh2dRscp=[-
-95
100]/serviceOffset2dRscp=0
usedFreqThresh2dRscp=[-
100]/serviceOffset2dRscp=0 -92
/usedFreqRelThresh2fRscp=
2
usedFreqThresh2dRscp=[-
100]/serviceOffset2dRscp=0 -95
usedFreqThresh2dRscp=[-
109,-
97]/serviceOffset2dRscp=0&
-4 -95
IfIratMobilityHsdpaEul=0&1
(DEACTIVED&ACTIVED)
usedFreqThresh2dRscp=[-
100]/serviceOffset2dRscp=0 -92
/usedFreqRelThresh2fRscp=
2
usedFreqThresh2dRscp=[-
109,-
97]/serviceOffset2dRscp=0&
-4 -92
IfIratMobilityHsdpaEul=0&1
(DEACTIVED&ACTIVED)
timeToTrigger2dEcno=320/ti
meToTrigger2dRscp=320 D320
timeToTrigger2fEcno=1280/
timeToTrigger2fRscp=1280 D1280
usedFreqThresh2dEcno=[-
11]/serviceOffset2dEcno=0 -14
usedFreqThresh2dEcno=[-
11,-
9]/serviceOffset2dEcno=0/u -12
sedFreqRelThresh2fEcno=2
usedFreqThresh2dEcno=[-
11]/serviceOffset2dEcno=0 -15
usedFreqThresh2dEcno=[-
16,-
9]/serviceOffset2dEcno=-
2&0 -15
IfIratMobilityHsdpaEul=0&1
(DEACTIVED&ACTIVED)
usedFreqThresh2dEcno=[-
11,-
9]/serviceOffset2dEcno=0/u -13
sedFreqRelThresh2fEcno=2
usedFreqThresh2dEcno=[-
16,-
9]/serviceOffset2dEcno=-
2&0 -13
IfIratMobilityHsdpaEul=0&1
(DEACTIVED&ACTIVED)
usedFreqThresh2dRscp=[-
100]/serviceOffset2dRscp=0 -100
usedFreqThresh2dRscp=[-
100]/serviceOffset2dRscp=0
/usedFreqRelThresh2fRscp= -97
2
usedFreqThresh2dRscp=[-
100]/serviceOffset2dRscp=0 -110
usedFreqThresh2dRscp=[-
109,-
97]/serviceOffset2dRscp=0&
-4 -110
IfIratMobilityHsdpaEul=0&1
(DEACTIVED&ACTIVED)
usedFreqThresh2dRscp=[-
100]/serviceOffset2dRscp=0
/usedFreqRelThresh2fRscp= -107
2
usedFreqThresh2dRscp=[-
109,-
97]/serviceOffset2dRscp=0&
-4 -107
IfIratMobilityHsdpaEul=0&1
(DEACTIVED&ACTIVED)
-95 16
-95 16
-95 16 maping
3 6
3 6
3 6
5 12
5 12
5 12
0 0
0 0
15 8
11 D320
12 D640
640 D640
3 D4000
3 D4000
2 8
11 D640
D4000
3 D4000
2 8
11 D640
RABINDEX级的参数无法提
-9, maping
取
-9 maping
RABINDEX级的参数无法提
-9 maping
取
RABINDEX级的参数无法提
-95 maping
取
RABINDEX级的参数无法提
-95 maping
取
RABINDEX级的参数无法提
-95 maping
取
2 2 maping
2 2 maping
1 1 maping
1 (TRUE) 1 maping
1 (TRUE) 1 maping
0 0 maping
3 3 maping
2&4 1&2 maping
4 2 maping
0 0 maping
new plan
0 0 maping
0 0 maping
0 0 maping
0 0 maping
640 D640
0 4
0 4
0 4
0 4
2 D2 maping
CPICH_EC/NO
D16
D16
2 D2 maping
CPICH_EC/NO
D16
D16
-12
-12
-12 maping
-92
-92
-92 maping
10 4
0 0
100 D0
usedFreqThresh2dEcno=[-
11,-
9]/serviceOffset2dEcno=0/u -12
sedFreqRelThresh4_2bEcno
=-1
usedFreqThresh2dRscp=[-
100]/serviceOffset2dRscp=0
-92
/usedFreqRelThresh4_2bRsc
p=-3
usedFreqThresh2dEcno=[-
11,-
9]/serviceOffset2dEcno=0/u -12
sedFreqRelThresh4_2bEcno
=-1
usedFreqThresh2dEcno=[-
11,-
9]/serviceOffset2dEcno=0/u -12
sedFreqRelThresh4_2bEcno
=-1
usedFreqThresh2dRscp=[-
100]/serviceOffset2dRscp=0 -92
/usedFreqRelThresh4_2bRsc
p=-3
usedFreqThresh2dRscp=[-
100]/serviceOffset2dRscp=0
-92
/usedFreqRelThresh4_2bRsc
p=-3
0 4
0 0
4 4
5 1
1 4
8 1
0 0 maping
2&4 2
4 1
5 6 maping
0 0
0 0
-50..50 0
3 3
0 0
-50..50 0
0 5
4
0(1228)/9(4)
0 0
ulRlcBufUpswitch=256/dlRlc
BufUpswitch=500 D512 maping
None D64
None D384
None 1024
None 1
None 1
None 1
None 8
None 1
None ON
None NO
None RateDegrade
None RateDegrade
None NO
None 10000
None 10000
None 10000
None 1
None D16
None D32
None D8
None D1000
None D8k
None 1
None ON
None ON
None 1
None 10000
None 15000
None D120
None 1
None 10000
None 10000
None 0
None 4
None 1
None D8
None 1
None 1
None 1
None FALSE(否)
None 1
None 1
None 10
None 1
None 1
None 1
None 1 maping
None 1 maping
None 1 maping
None 1 maping
None 1 maping
None 1 maping
None 1 maping
None 1 maping
None 1 maping
None 1 maping
None 1
None 1 maping
None 1 maping
None 1 maping
None 1 maping
None 15000
None 35000
None 3 maping
None 3 maping
10 10 maping
featureState=0、licenseStat 0 maping
e=1、serviceState=0
0 (DEACTIVATED) 0 maping
LOOSE_CAC
None
None 1
None 1
None 0
None 1
None ALGORITHM_SECOND
None ALGORITHM_FIRST
None D50
None 0
None 0
None 0
None 0
None 10
None 0
None D1000
None 0
None 1
None 1
None 1
None 1
None 1
None SF64(SF64)
None SF128(SF128)
None LOOSE_CAC
None 5
None 5
None 0
None ON
None ON
None 0
None ON
None 1
None DCH8KHSDPA
None 0
None 1
None 60
None 60
SET
UCORRMALGOSWITCH:Logic
RncId=xxx,DraSwitch2
=DRA_PS_STATE_TRANS_W
HEN_CS_REL_SWITCH=1;
None SET
UCOIFTIMER:LogicRncId=xxx
,ZeroRateUpFailToRelTimerL
en
=180;
None 1
None D20
None D20
None 1
None 1
None 1
None 1
None 1
1 (TRUE) 1 maping
not found DCH maping
edchTti2Support=[1048(OFF 0 maping
),4(ON)]
0 maping
None D8
None D8
None OFF
None 1
None 1
None 50
None 0
None 10s
None 30
None 1
None 1
None MaxHsupaUserNum=40,ER
GCHEHICHCODENUM=2.
SET
None UUESTATETRANS:BasedTime
F2DThd=28,BasedTimeF2DP
T=30;
SET UCORRMALGOSWITCH:
CmpSwitch2=CMP_F2D_RLC
None _ONESIDE_REBUILD_SWITC
H-1;
SET UCORRMALGOSWITCH:
CmpSwitch=CMP_D2F_RLC_
None
ONESIDE_REBUILD_SWITCH-
1;
None 0
SET UCORRMALGOSWITCH:
DraSwitch2=DRA_PCPICH_E
None CN0_ON_RACH_UPDATE_S
WITCH-1;
SET UCORRMPARA:
PerfEnhanceSwitch=PERFEN
None H_HSUPA_TTI_RECFG_PROC
_OPT_SWITCH-1;
SET
UNBMPARA:PerfEnhanceSwi
None tch=PERFENH_HRNTI_OPT_S
WITCH-1; (R15/R16)
None 0
None 0 maping
None 0 maping
0 0 maping
None D0
None D0
None D0
None D1000
None D1000
None 4
None 30
空值 10 maping
None 1
None 1
None 8
None 1
2 1 maping
None 1
5
-18 baseline
-58,QrxlevminInd=False baseline
0 0 mapping
[-50,50] [-50,50] mapping
0 0 mapping
0 0 mapping
0 0 mapping
0 0 mapping
0 0 mapping
[-50,50] 0 mapping
0 0 mapping
to
DYNAMIC_BW_SHA
PING, flow
allocation for HSDPA
Type
usersof channel that
is performed
preferably
according
Parameterto carries
the
Network Element Parameter ID Parameter Name the
delaysignaling
and packet RB. -
Description
DCH: Both
loss of the uplink
and downlink
Indicates
transmission are
the HSDPA
NodeB SM Scheduling Method preferably
Scheduling carried
Method
interface board
Indicates the powerin
on
of DCH.
the - HSDPA:
SIMPLE_FLOW_CTRL
HS-SCCH is an
NodeB SWITCH Cabinet No Uplink
mode inis dBpreferably
offset to the
carried
transmitonpower
Indicates DCH,
the and
HS-of
NodeB SCCHPWR downlink is
HS-SCCH Power the PCPICH.
SCCH Power Control
HSSCCHPWRCMIND Control Method in preferably
Method in carried
CELL DCH
NodeB CELL DCH state on HS-DSCH. -
state
CH IndicatesUplink
the is
HSUPA:
Indicates
16QAM Switch.
preferably the Power
carriedThe
NodeB PWRMGN Power Margin Margin Ratio
Indicates
function
on the
E-DCH,will andbe
Dynamic Code Dynamic
maximum
enabled
downlink ifCode
power
isthis
NodeB DYNCODESW Switch Switch
used for scheduled
parameter
preferably is set to
carried
users
OPEN.
on after
DCH.When
- thethis
HSPA:
CELL EXTRAPOWER EXTRAPOWER scheduling
switch
Uplink turned on,
is preferably
the cell on
carried throughput
E-DCH,
CELL CME16QAMSW 16QAM Switch improves
Type of Channel and downlink is
Preferably Carrying preferably carried
RNC SrbChlType
PERFENH_SRB_OVE Signaling RB
PERFENH_SRB_OVE on HS-DSCH
PERFENH_SRB_OVE
RNC R_HSUPA_TTI10_S R_HSUPA_TTI10_S R_HSUPA_TTI10_S
WITCH WITCH WITCH
STATIC_BW_SHAPIN
G(静态流量成形),
DYNAMIC_BW_SHA
PING(动态流量成形
),
Recommend
MML Command EPF(Enhanced
NO_BW_SHAPING(PF), Use base line ESN Parameter ID
Parameter Range
SET PF(PF),
无流量成形), RR(Round
ULOCELLMACHSPAR Robin), MAXCI(Max BW_SHAPING_ONO
BW_SHAPING_ONO
A C/I) EPF(增强PF) null
FF_TOGGLE(BW_SH
SET FF_TOGGLE(自选择 APING_ONOFF_TOG
DLFLOWCTRLPARA 流量成形) GLE) null
SET
ULOCELLMACHSPAR CQI(基于CQI的自适
A
SET 0~80 28 null
ULOCELLMACHSPAR 应功控),
A FIXED(功率固定) CQI null
DCH(上行DCH,下
SET MACHSPARA 行DCH),
0~100 HSDPA(上 5 null
行DCH,下行
OPEN(开), CLOSE(关
null
SET MACHSPARA )HSDSCH), HSUPA(上 OPEN
ULOCELLMACHSPAR
行EDCH,下行 0 null
SAET 0~40
ULOCELLMACHSPAR DCH), HSPA(上行
A OPEN, CLOSE DCH(上行DCH,下
OPEN null
EDCH,下行
SET HSDSCH) 行DCH)
UFRCCHLTYPEPARA null
use baseline
use baseline
use baseline
use baseline
use baseline
use baseline
use baseline
use baseline
use baseline
use baseline
used to select a
feature
This related to
parameter is
HSPA+.
used to Ifselect
a feature a is
selected,
feature it
related
This parameter is indicates
to
that
usedthe
HSPA+. to Ifselect
a feature a is
corresponding
selected,
feature it indicates
related to
This parameter
algorithm is
Huawei
that
The
HSPA+.
used the
parameter
to If aisfeature
select
enabled.
a is
If a feature
corresponding
specifies
selected, the
it isnumber
not
indicates
feature
This related
parameter
selected, to
is
itisindicates
Network algorithm
of
thatHS-DPSCH
Parameter
HSPA+. the If a enabled.
codes.
feature is
Parameter ID Parameter Name used
that
If to select
the is not
a feature a
Element Description
This parameter
corresponding
selected,
feature it
related is
indicates
to
Cell Hspa Plus function This
valid parameter
corresponding
selected,
algorithmonly itwhen is
indicates
isfeature
enabled.
that
HSPA+.
used the
algorithmto If a
selectis a
disabled. is
Cell DL_L2ENHANCED switch that
Allocate
If the Code
a feature
corresponding Mode is
is not
selected,
feature
Note that it
related indicates
toFor
Cell Hspa Plus function corresponding
set tothe
selected,
algorithm
that itother
"Manual". indicates
isfeature
enabled.
HSPA+.
factors
algorithm
detailed
that If
such a is
the information as license
disabled. is
Cell E_FACH switch If a feature
corresponding
selected, it is not
indicates
and
Note
about the
that physical
thisitother
Cell Hspa Plus function corresponding
selected,
algorithm
that
factors the
capability such isparameter,
of indicates
enabled.
NodeB
as
Cell 64QAM switch refer
algorithm
that
If a to
the
feature 3GPP TSlicense
isisdisabled.
not
corresponding
restrict
and
25.308
Note the
that whether
physical
other a
Cell Hspa Plus function corresponding
selected,
algorithm
feature can itis indicates
enabled.
be used
capability
factors
algorithm such of NodeB
as
isfeaturelicense
Cell MIMO switch that
If
even
restrict
and
the
a feature
if this
the whether
physicalisdisabled.
nota is
Note
selected,
selected.thatit
corresponding other
The indicates
Cell Hspa Plus function feature
capability can of be used
NodeB
Cell 64QAM_MIMO switch factors
algorithm
that the
EFACH/MIMO such is as license
disabled.
switch
even
restrict
Maximum
and if
the this
whether feature
number
physical a ofis
Cell Hspa Plus function Note that
corresponding
determines
selected. other
The whether
feature
users
capability
factors can
supported
such of be used
NodeB
as by
license
Cell DC_HSDPA switch algorithm
the cell
EFACH/MIMO
even if this isfeature
supports disabled.
theis
switch
the
and
Note HSDPA
restrict
Maximumthe
that whether channel.
number
physical
other a of
E-FACH/MIMO
determines
selected.
The user The
in whether
this
Cell Hspa Plus function feature
users
capability
factors
feature can
supported
such be
butofrefers used
NodeB
as
does by
license
not
Cell DCMIMO_HSDP If
theE_F_DPCH
cell
EFACH/MIMO
parameter
even if supports
this are the
switch
feature tois
switch the
and
affect HSUPA
restrict
the
selected, thewhether
physical
the channel. a
E-FACH/MIMO
determines
the user
selected.
The usercan with
The
in whether
thisservices
Cell Hspa Enhanced feature
capability
establishment
corresponding
feature be
butofrefers
does used
NodeB
of the
not
Cell E_F_DPCH_ON the
on cell
the
EFACH/MIMO
parameter
even if supports
HSDPA
this the
switch
feature tois
function switch restrict
E-FACH
function
affect
E-FACH/MIMO whether
and
will
thewith the
be a
channel,
determines
the
When
featureuser
selected. the regardless
can The whether
switch services
be ofusedis of
MIMO
MAP_HSUPA_TTI_2M Service Mapping Strategy enabled;
establishment
feature
the numbercell
butotherwise,
does
of RABs the
not
RNC S_SWITCH Switch
on
even 2cell
the
EFACH/MIMO
on,
disabled
E-FACH ifms supports
HSUPA
TTIfeature
this
and the
theis
is switch
affect
carried
E-FACH/MIMO
channel, theon the
regardless HSDPA
determines
supported
selected.
MIMO
establishmentcell The of theof
whether
for HSUPA
Maximum HSDPA user channel.
feature
the number
cell
EFACH/MIMO Maximum
but
supports does not
of switch
RABsthe
Cell MaxHsdpaUserNum E-FACH andthe the
number HSDPA
affect
carried
E-FACH/MIMO
determines user
theon number
HSUPA
whether
Maximum HSUPA user MIMO
cannot
establishment
channel.
feature cell
exceed
Maximum
but does the
of the
not
Cell MaxHsupaUserNum number the cell supports the
HSDPA
E-FACH/MIMO of
E-FACH
HSUPA
affect capability
and
user
the the
number
the
MIMO
cannot NodeB
establishment
feature butproduct,
cell
exceed does the
of theIn
not
practice,
HSUPA
E-FACH
affect the and the ofcan
the
capability value
be
the
MIMOsetNodeBbased
establishmentcell product,onofthetheIn
cell type
practice, and
E-FACH and the can
the the
value
richness
be
MIMOset based of the
cell on the
available
cell type and HSDPA the
power and
richness of codethe
resources.HSUPA
available
power and code
resources
Ericsson