Professional Documents
Culture Documents
High Speed CAN-Transceiver: Automotive Power
High Speed CAN-Transceiver: Automotive Power
0, April 2008
TLE6250
High Speed CAN-Transceiver
Automotive Power
Edition 2008-04-28
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2004 Infineon Technologies AG
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any
information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties
and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights
of any third party.
Information
For further information on technology, delivery terms and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements, components may contain dangerous substances. For information on the types in
question, please contact the nearest Infineon Technologies Office.
Infineon Technologies components may be used in life-support devices or systems only with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
High Speed CAN-Transceiver TLE6250
Features
• CAN data transmission rate up to 1 MBaud
• Receive-only Mode and Stand-by Mode
• Suitable for 12 V and 24 V applications
• Excellent EMC performance (very high immunity and
very low emission)
• Version for 5 V and 3.3 V microcontrollers
• Bus pins are short circuit proof to ground and battery
voltage
• Overtemperature protection
• Very wide temperature range (-40 °C up to 150 °C)
• Green Product (RoHS compliant)
• AEC Qualified
Description
The HS CAN-transceiver family TLE6250 (TLE6250G and TLE6250GV33) are
monolithic integrated circuits that are available as bare die as well as in a PG-DSO-8
package. The ICs are optimized for high speed differential mode data transmission in
automotive and industrial applications and they are compatible to ISO/DIS 11898. They
work as an interface between the CAN protocol controller and the physical differential
bus in both, 12 V and 24 V systems.
The ICs are based on the Smart Power Technology SPT® which allows bipolar and
CMOS control circuitry in accordance with DMOS power devices existing on the same
monolithic circuit. The TLE6250G is designed to withstand the severe conditions of
automotive applications and provides excellent EMC performance.
Note: There are two versions available (refer to next page).
Type Package
TLE6250G PG-DSO-8
TLE6250C (chip)
TLE6250GV33 PG-DSO-8
TLE6250CV33 (chip)
TLE6250G
5 V logic I/O version: RxD, TxD, INH, RM. Two Control pins (RM, INH) and 3 operation
modes: Normal Mode, Stand-by Mode and Receive Only Mode.
TLE6250GV33
3.3 V logic I/O version (logic I/O voltage adaptive to V33 pin within the range 3.3 V to 5 V):
RxD, TxD, INH. One control pin (INH) and two operation modes: Normal Mode and
Standby Mode.
Pin Configuration
T L E6250 G
T xD 1 8 IN H
GN D 2 7 C AN H
V CC 3 6 C AN L
R xD 4 5 RM
AEP03320.VSD
T LE6250GV 33
T xD 1 8 IN H
GN D 2 7 C AN H
V CC 3 6 C AN L
R xD 4 5 V 33 V
AEP03321.VSD
TL E6250 G
3
VCC
7 D river
C AN H
Output 1
T em p- T xD
6 Stage
C AN L Protection
8
M ode C ontrol IN H
5
RM
=
R eceiver
* 4
R xD
2
GN D
AEA 03311.VSD
TL E6250 GV33
3
VCC
5
V33
7 D river
C AN H
Output 1
T em p- T xD
6 Stage
C AN L Protection
8
M ode C ontrol IN H
R eceiver
* 4
R xD
2
GN D
AEA 03312.VSD
Application Information
TLE6250G
Normal Mode
INH = 1 RM = 0
INH = 0 RM = 1
INH = 0
RM = 1
and RM = 1
INH = 0
and RM = 0
Stand-by Mode Receive-only Mode
INH = 1
INH = 1 RM = 0 / 1 INH = 0 RM = 0
AED02924
Normal Mode
INH = 0
INH = 1 INH = 0
Stand-by
Mode
INH = 1
AEA03327.VSD
TLE6250GV33
In the normal mode the device is able to receive and to transmit messages whereas in
the receive-only mode signals at the TxD input are not transmitted to the CAN bus. The
receive-only mode can be used for diagnostic purposes (to check the bus connections
between the nodes) as well as to prevent the bus being blocked by a faulty permanent
dominant TxD input signal. The stand-by mode is a low power mode that disables both,
the receiver as well as the transmitter.
In case the receive-only feature is not used the RM pin has to be left open. When the
stand-by mode is not used the INH pin has to be connected to ground level in order to
switch the TLE6250G in normal mode.
e. g. TLE 4476
5V
VQ 1
VI
3 .3 V
VQ 2
+ 22 100 GN D + +
22 µF 22 µF
µF nF
AEA 03300.VSD
e. g. T LE 4270
5V
VI VQ
+ 22 100 +
GN D 22 µF
µF nF
AEA 03299.VSD
TL E6250 GV 33
8
IN H
4
7 R xD
C AN H 1
6 TxD µP
C AN L 5 5V
V 33 V
3
V CC
GN D 100 GN D
100
2 nF nF
e. g. T LE 4270
VI VQ
+ 22 100 5V +
GN D 22 µF
µF nF
e. g. T LE 4270
VI VQ
5V +
+ 22 100 GN D
µF nF
AEA 13299.VSD
Figure 6 (cont.) Application Circuits TLE6250GV33 Used for 3.3 V and 5 V Logic
Note: Maximum ratings are absolute ratings; exceeding any one of these values may
cause irreversible damage to the integrated circuit.
Note: Maximum ratings are absolute ratings; exceeding any one of these values may
cause irreversible damage to the integrated circuit.
Diagrams
8
INH
7 1
CANH TxD
5
RM
47 pF 60 Ω
4
RxD
20 pF
6
CANL
3 5V
VCC
GND
100 nF
2
AEA03328.VSD
8
INH
7 1
CANH TxD
4
RxD
20 pF
47 pF 60 Ω
5 3.3 V
V33 V
100 nF
6
CANL
3 5V
VCC
GND
100 nF
2
AEA03329.VSD
VTxD
VCC(33V)
GND
VDIFF(d)
VDIFF(r)
VRxD t
td(L), R td(H), R
VCC(33V)
0.7VCC(33V)
0.3VCC(33V)
GND
td(L), TR td(H), TR t
AET02926
Application
120 Ω
V Bat T L E6250 G
C AN 5
Bus RM
8
IN H
7 4
C AN H R xD µP
6 1
C AN L T xD
3
V CC
GN D 100 100 GN D
2 nF nF
e. g . T LE 4270
5V
VI VQ
+ 22 100 +
GN D 22 µF
µF nF
EC U 1
T L E6250 GV33
8
IN H
4
R xD
7 1
C AN H T xD µP
6 5
C AN L V 33 V
3
V CC
GN D 100 100 100 GN D
2 nF nF nF
e. g . T LE 4476
5V
V Q1
VI
3.3 V
V Q2
+ 22 100 + +
GN D 22 µF 22 µF
µF nF
EC U X
120 Ω
AEA03308.VSD
Package Outlines
0.35 x 45˚
4 -0.2 1)
1.75 MAX.
0.175 ±0.07
0.19 +0.06
(1.45)
C
8 MAX.
1.27 B
0.1 0.64 ±0.25
0.41+0.1
-0.06
2)
6 ±0.2
0.2 M A B 8x 0.2 M C 8x
8 5
1 4
A
5 -0.2 1)
Index Marking
1) Does not include plastic or metal protrusion of 0.15 max. per side
2) Lead width can be 0.61 max. in dambar area
GPS01181
You can find all of our packages, sorts of packing and others in our
Infineon Internet Page “Products”: http://www.infineon.com/products.