Professional Documents
Culture Documents
All Sample Views Final
All Sample Views Final
This sample drawing is to illustrate the basic information required. Your drawing must be "site specific" Letter Description
Distance from crossing to nearest actual milepost
ALL INFORMATION ON THIS SAMPLE DRAWING IS REQUIRED ON YOUR DRAWING TO BE SUBMITTED TO CSX. ( __ feet from MP____ ). OR: Distance from
(a)
crossing to centerline of nearest public road
intersection (include DOT Crossing #)
(b) Width of CSX R/W
(c) Distance from centerline of track to R/W
Total length of pipe on CSX R/W
(d)
NOTES:
MANHOLES/HANDHOLES/POLES/PULL BOXES/OTHERS
ARE NOT PERMITTED ON CSX R/W.
Location: _________________________________________
Latitude: NBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
Longitude: WBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
This sample drawing is to illustrate the basic information required. Your drawing must be "site specific REFER TO ENGINEERING
ALL INFORMATION ON IN THIS SAMPLE DRAWING, INCLUDING THE TABLE, ARE REQUIRED ON YOUR DRAWING TO BE SUBMITTED TO CSX. SPECIFICATIONS IN THE APPLICATION
PACKAGE FOR ADDITIONAL
INFORMATION AND GUIDANCE.
(d) Height of wire above CSX aerial facilities Type of Wire Supports: Drawing Scale: V _______ Inches = _______ Feet
False Dead Ends:
(e) Distance between existing and proposed cable/wireline Drawing Scale: H _______ Inches = _______ Feet
Total # of CSX Pole Lines to be Crossed:
Print Form
"SAMPLE -$&.$1'%25(PROFILE VIEW ONLY" NOTES:
This sample drawing is to illustrate the basic information required. Your drawing must be "site specific" REFER TO ENGINEERING
ALL INFORMATION ON THIS SAMPLE DRAWING, INCLUDING THE BELOW TABLE, ARE REQUIRED ON YOUR DRAWING TO BE SUBMITTED TO CSX. SPECIFICATIONS IN THE APPLICATION
PACKAGE FOR ADDITIONAL
INFORMATION AND GUIDANCE.
*'"11-*$"#-&
)%1&%303
#&55&3.645#&64&%
$49#03&1-"/5&.1-"5&"/%
'3"$5*0/.*5*("5*0/1-"/50#&
46#.*55&%50$49'033&7*&8"/%
"11307"-13*0350$0/4536$5*0/
LEGEND
Letter Description PIPELINE CONTENT DETAILS
(a) Distance from centerline of track to CSX R/W
Commodity Description:
(b)
Distance from base-of-rail to top-of-casing
Maximum Operating Pressure: YOUR TITLE BLOCK
Is Commodity Flammable: Yes No
Distance from base-of-ditch to top-of-casing
(c)
CARRIER/CASING PIPE DETAILS
Total length of pipe on CSX R/W Carrier Pipe Casing Pipe
(d)
Pipe Material:
Location: _________________________________________
Distance from centerline of nearest track to face of pits at a 90
(e) Material Specifications & Grade:
degree angle to the track(s)
Specified Minimum Yield Strength: Latitude: NBBBBBBBBBBBBBBBBBBBBBBBBBBBB
Distance from top-of-vent pipe to ground surface (4' minimum
(f)
required) Nominal Size Outside Diameter (Inches): Longitude: WBBBBBBBBBBBBBBBBBBBBBBBBBBB
Distance from centerline of track to vent pipe at a 90 degree Wall Thickness (Inches):
(g)
angle to the track(s) Type of Seam: Drawing No.: _______________________ Sheet: _____ of _____
Theoretical Embankment Line: Starts 12' from centerline of Type of Joints:
(h) track and extends away from track at a slope of 1.5' over and 1' Drawing Date: ____/____/______ Revised: ____/____/______
down Tunnel Liner Plates Required: Yes No
Drawing Scale: V _______ Inches = _______ Feet
(i) Carrier pipe diameter Cathodic Protection: Yes No Type: _______________________
(j) Casing pipe diameter Protective Coating: Yes No Type: _______________________ Drawing Scale: H _______ Inches = _______ Feet
(k) Depth of Launching/Receiving Pit Temp. Track Support or Rip-Rap Req.: Yes No Must Describe & Show on Dwg.
"SAMPLE+'' SUBGRADE WIRE/CABLE PROFILE VIEW ONLY" NOTES:
This sample drawing is to illustrate the basic information required. Your drawing must be "site specific"
REFER TO+'',17(5,0*8,'(/,1(6
ALL INFORMATION ON THIS SAMPLE DRAWING, INCLUDING THE TABLE, ARE REQUIRED ON YOUR DRAWING TO BE SUBMITTED TO CSX. $1' ENGINEERING SPECIFICATIONS
IN THE APPLICATION PACKAGE FOR
ADDITIONAL INFORMATION AND
GUIDANCE.
LOCATE CSX'S SIGNAL FACILITIES
AND/OR WARNING DEVICES AT
PROPOSED FACILITY CROSSING
LOCATION, I.E. CANTILEVERS,
FLASHERS, GATES AND SHOW
CLEARANCES.
CASING PIPE ENDS MUST BE SEALED
TO PREVENT ENTRANCE OF
FOREIGN MATERIALS.
,)$33/,&$%/(+'3('525
%(77(50867%(86('
&6;%25(3/$17(03/$7($1'
)5$&7,210,7,*$7,213/$172
%(68%0,77('72&6;)255(9,(:
$1'$33529$/35,2572
&216758&7,21