Professional Documents
Culture Documents
Samsung+cm-1819 1829 1419 1429
Samsung+cm-1819 1829 1419 1429
Samsung+cm-1819 1829 1419 1429
CM-1819 / CM-1419
CM-1829 / CM-1429
2. Specifications
3. Operating Instructions
6. Troubleshooting
P 1 2 3 4 5 6 7 8 9 0
+ 20sec
SEUK
1. Precaution
Follow these special safety precautions. Although the microwave oven is completely safe during ordinary
use, repair work can be extremely hazardous due to possible exposure to microwave radiation, as well as
potentially lethal high voltages and currents.
Samsung Electronics 1
Precaution
Negative Terminal
PRECAUTION Note :Touch chassis side first then short to
the high voltage capacitor terminal by
There exists HIGH VOLTAGE ELECTRICITY using a screwdriver.
with high current capabilities in the circuits of
the HIGH VOLTAGE TRANSFORMER
secondary and filament terminals. It is
extremely dangerous to work on or near these
circuits with the oven energized.
DO NOT measure the voltage in the high
voltage circuit including filament voltage of
magnetron.
PRECAUTION
Never touch any circuit wiring with your hand
nor with an insulated tool during operation.
PRECAUTION
Servicemen should remove their watches
whenever working close to or replacing the
magnetron.
2 Samsung Electronics
2. Specifications
2-1 Table of Specifications (CM-1819 / CM-1419)
Samsung Electronics 3
3. Operating Instructions
3-1 Features (CM-1819 / CM-1419)
SAFETY INTERLOCK
HOLES
DOOR
CEILING COVER
SAFETY INTERLOCK
HOLES
DOOR
4 Samsung Electronics
Operating Instructions
3-3 Control Panel (CM-1829 / CM-1429)
1 2 4
P 1 2 3 4 5 6 7 8 9 0
+ 20sec
3 5 6 7 8 9 10
1. DISPLAY
2. PROGRAM PAD
3. PROGRAM LOCK PAD
4. NUMBER PADS(TIME, MEMORY PROGRAMMING)
5. POWER LEVEL SELECTOR PAD
6. DEFROST SELECTOR PAD
7. DOUBLE QUANTITY PAD
8. +20sec PAD (ONE TOUCH COOK PAD)
9. STOP/CANCEL PAD
10. START BUTTON
Samsung Electronics 5
Operating Instructions
Cooking/Reheating
1. Make sure the oven is plugged into a properly earthed electrical outlet and ‘ON’ appears in the display
window.
3. Put the food into a suitable container, place it in the center of the oven and then close the door securely.
Result: The oven lamp will go off.
4. Select the desired power level by rotating the COOKING POWER CONTROL DIAL.
Result: The selected power level will be displayed in the display window.
6. Press pad:
Result:The oven lamp and cooling fan will be turned on.
Heating will start.
The time on digital display will count down.
7. When all time is elapsed, the end of cycle Beep Tone will sound 4 times and all heating will stop. The
oven lamp will go off. For 1 min, the display shows and the cooling fan will keep working in order to cool
down the interior parts. During the time, the fan will not stop even when you open the door. 1 min later it
will stop and ON appears again. Food may be removed from oven whilst the fan is still running.
NOTE: Whilst heating, one press on pad stops the oven. You can restart it by pressing the pad or a
second press on pad will cancel the selected program. When it is NOT in a heating cycle, one tap
on pad cancels the selected program. You can set the power level first and then the cooking time
next, or vice versa. You can press +20sec button one or more times in order to add the cooking
time by 20 seconds.
6 Samsung Electronics
Operating Instructions
3-5 Operation Guide (CM-1819 / CM-1419 continued)
If you want to cancel any cooking settings before starting cooking, simply press once.
4. Rotate the Variable Cooking Power Control dial to the DEFROST HIGH( ) or DEFROST LOW( ) as
you wish.
Result: The DEFROST indicator appears on the digital display.
6. Press button.
Result: Defrosting begins.
Samsung Electronics 7
Operating Instructions
3-5 Operation Guide (CM-1829 / CM-1429)
Cooking/Reheating
NOTE: When you first plug in the power cord, the oven beeps once and all the indicators show for 5 sec in
the display window.
NOTE: When heating cycle is completed and you open the door, the oven lamp automatically turns on and
goes off 1 min later.
NOTE: When you open the door whilst in a heating cycle, the oven stops operating and the oven lamp
automatically turns on for 1 min and goes off 1 min later. If you leave the oven door open for more
than 1 min, the oven beeps once every minute and after 5 min the power source check indicator
‘ON’ appears in the display window.
1. Make sure the oven is plugged into a properly earthed electrical outlet and ‘ON’ appears in the display
window.
3. Put the food into a suitable container, place it in the centre of the oven and then close the door securely.
Result: The oven lamp will go off.
4. Select the desired power level by pressing the Power Level Selector pad.
Result: The selected power level will be displayed in the display window.
7. When all time is elapsed, the end of cycle Beep Tone will sound 4 times and all heating will stop. The
oven lamp will go off. For 1 min, the display shows and the cooling fan will keep working in order to
cool down the interior parts. During the time, the fan will not stop even when you open the door. 1 min
later it will stop and ‘ON’ appears again. Food may be removed from oven whilst the fan is still running.
8 Samsung Electronics
Operating Instructions
3-5 Operation Guide (CM-1829 / CM-1429 continued)
NOTE: When the oven was operating for longer than 25 min under Defrosting cycle, you can NOT change
the power level from Defrosting to Heating(Cooking/Reheating) mode.
NOTE: The oven is designed not to work when power level is set to ‘0’ mode between the heating mode
and the defrosting mode.
4. Press the Defrost selector pad to set DEFROST HIGH ( ) or DEFROST LOW ( ) as you wish.
Result: The selected DEFROST indicator appears in the display.
5. Press the Number pads to set the defrosting time. (Max. 50 min)
6. Press button.
Result: Defrosting begins.
NOTE: It is not possible to set a defrosting time for longer than 50min. The defrost indicator will flash and it
is advisable to press CANCEL and enter a new defrost level and time.
Repeat Feature
You can repeat the previous cooking setting (regardless of manual or automatic memory heating) by
pressing the START button. The oven starts with exactly the same heating time and power level that were
used in the last operation.
NOTE: Repeat feature does not support for +20sec pad. The repeat feature will be cancelled once the
power source is cut off.
Samsung Electronics 9
Operating Instructions
3-5 Operation Guide (CM-1829 / CM-1429 continued)
1. Hold down PROGRAM LOCK pad and then press PROGRAM pad. Hold together for 2 sec.
Be sure to press the pads firmly.
Result: PROG indicator appears in the digital display.
NOTE: It is not possible to set a cooking time for longer than the maximum time allowed on the chosen
program. The power level indicator will flash and it is advisable to press CANCEL and to enter a new
power level and cooking time.
5. Hold down PROGRAM LOCK pad and then press PROGRAM pad. Hold together for 2 sec once again.
Result: PROG indicator and memory number indicator blink 3 times in the digital display with a beep
sound. And then the display goes blank.
Caution: Be sure to press the pads firmly in the right position.
6. When you want to program more, repeat the procedures above again.
Memory programs are available up to 30 items. Make sure the unit is properly programmed.
After programming is finished, all you have to do for memory cooking is to press the NUMBER pad. Then
the selected memory program automatically starts cooking.
10 Samsung Electronics
Operating Instructions
After having finished memory programming, just press the NUMBER pad of the memory number you want to
select. The oven will automatically start heating according to the pre-programmed cooking time and power
level after a short delay (5 sec).
1. Make sure the oven is plugged into a properly earthed electrical outlet and ‘ON’ appears in the display
window.
3. Put the food into a suitable container, place it in the centre of the oven and then close the door securely.
Result: The oven lamp will go off.
If you want to cancel any cooking settings before starting cooking, simply press CANCEL pad once.
Samsung Electronics 11
Operating Instructions
The power level function enables you to adapt the amount of energy dissipated and thus the time required to
cook or reheat your food, according to its type and quantity. You can choose between the power levels
below.
.....................................................................................................................................................
Power Level Percentage CM-1819/1829 Percentage CM-1419/1429
.....................................................................................................................................................
HIGH( ) 100% 1800 W 100% 1400W
MEDIUM( ) 70% 1260 W 70% 980W
LOW( ) 50% 900 W 50% 700W
HIGH DEFROST( ) 20% 360 W 25% 360W
LOW DEFROST( ) 10% 180 W 13% 180W
.....................................................................................................................................................
You cannot set the cooking time longer than maximum value allowed to each specific power level. (see
below.)
..................................................................
Power Level Max. Time
..................................................................
HIGH 25 min.
MEDIUM 40 min.
LOW 40 min.
HIGH DEFROST 50 min.
LOW DEFROST 50 min.
..................................................................
12 Samsung Electronics
4. Disassembly and Reassembly
4-1 Replacement of Magnetron
Remove the magnetron including the shield case,
permanent magnet, choke coils and capacitors (all
of which are contained in one assembly). Duct-MGT-L
Nut-Flange
1. Remove the outer panel. Duct-Fan
NOTE: Before servicing, make sure to discharge
electric charge remaining on the high
voltage capacitors or wait for more than 5
min.
2. Remove the back cover.
3. Disconnect all lead wires from the magnetron.
4. Remove screws securing the duct-MGT and
duct-fan.
5. Remove the nut-flanges securing the
magnetron by using a box wrench.
6. Take out the magnetron very carefully. Duct-
NOTE1: When removing the magnetron, make MGT-R
sure that its antenna does not hit any
adjacent parts, or it may be damaged.
NOTE2: When replacing the magnetron, be Magnetron
sure to remount the magnetron gasket
in the correct position and make sure
the gasket is in good condition.
(See page 19 for adjustment
instructions.)
LVT
4 Mounting Bolts
Samsung Electronics 13
Disassembly and Reassembly
NOTE: Be sure to wear gloves when you 1. Remove hex bolts securing the upper hinge
disassemble or assemble the parts. and lower hinge. Then remove the door
assembly.
1. Remove hex bolts securing the upper hinge 2. Insert the flat screwdriver or thin metal plate
and lower hinge. Then remove the door into the gap between the door E and door C to
assembly. remove Door C from the door assembly.
2. Insert the flat screwdriver or thin metal plate NOTE: Be careful when handling Door C as is
into the gap between the door E and door C to fragile.
remove Door C from the door assembly. NOTE: The thickness of the flat screwdriver or
3. Remove 2 screws securing the Door Handle. thin metal plate inserted into the gap
4. Unbend the 6 metal tabs around the trim of should be 0.5mm or less.
Decoration Door Cover. 3. Remove 2 screws securing the Door Handle to
5. Remove 3 screws securing the Door E Ass’y. the Door E Ass’y.
6. Remove upper hinge and lower hinge. 4. Unbend the 2 metal tabs at both ends of the
7. Remove Decoration Door, Screen B, Key-Door, Door Handle to remove the Door Handle Cover
Spring-Key, Pin-Key as needed. from the Door Handle.
Door C
Upper Hinge
Door E Ass’y
Decoration Door
Screen B
1. When mounting the door to the oven, be sure to adjust the door parallel to the bottom line of the oven
face plate by moving the upper hinge and lower hinge in the direction necessary for proper alignment.
2. Adjust so that the door has no play between the inner door surface and oven front surface. If the door
assembly is not mounted properly, microwave energy may leak from the space between the door and
oven.
3. Do the microwave leakage test.
14 Samsung Electronics
Disassembly and Reassembly
Ass’y Stirrer
Ass’y Stirrer Cover
Plastic Clips
Samsung Electronics 15
Disassembly and Reassembly
Panel-Base
Wire Harness-D
PCB2
Button-Select
Button-Start
Main P.C.Board
(PCB1)
Control Box Ass’y
(CM-1819/1419) Wire Harness-C
Digitron(PCB4)
Wire Harness-F
Window-Display
Cover Panel
PCB3
Cover-Panel/L
Switch-Membrane
16 Samsung Electronics
Disassembly and Reassembly
Samsung Electronics 17
Disassembly and Reassembly
H.V.Capacitor
18 Samsung Electronics
5. Alignment and Adjustments
PRECAUTION
1. High voltage is present at the high voltage terminals during any cook cycle.
2. It is neither necessary nor advisable to attempt measurement of the high voltage.
3. Before touching any oven components or wiring, always unplug the oven from its power source and
discharge the high voltage capacitor.
Terminal Resistance
5-3 Magnetron
Continuity checks can indicate only an open Magnetron Antenna
filament or a short magnetron. To diagnose an
open filament or short magnetron :
1. Isolate the magnetron from the circuit by Gasket
disconnecting its leads. Plate
2. A continuity check across the magnetron filament Cooling Fins
terminals should indicate one ohm or less.
3. A continuity check between each filament terminal
and magnetron case should read open.
Samsung Electronics 19
Alignment and Adjustments
Precaution
For continued protection against radiation
hazard, replace parts in accordance with the Latch-Body
wiring diagram and be sure to use the correct
part number for the following switches: Primary
and door sensing switches, and the interlock Door Sensing S/W
monitor switch (replace all together). Then Lever-Switch/U
follow the adjustment procedures below. After
repair and adjustment, be sure to check the
continuity of all interlock switches and the Interlock Monitor S/W
interlock monitor switch.
Primary S/W
20 Samsung Electronics
Alignment and Adjustments
CAUTION
MICROWAVE RADIATION
PERSONNEL SHOULD NOT ALLOW EXPOSURE TO MICROWAVE RADIATION FROM MICROWAVE
GENERATOR OR OTHER PARTS CONDUCTING MICROWAVE ENERGY.
The output power of the magnetron can be measured by performing a water temperature rise test.
Equipment needed :
* Two 1-liter cylindrical borosilicate glass vessel (Outside diameter 190 mm)
* One glass thermometer with mercury column
NOTE: Check line voltage under load. Low voltage will lower the magnetron output. Make all temperature and
time tests with accurate equipment.
1. Fill the one liter glass vessel with water.
2. Stir water in glass vessel with thermometer, and record glass vessel's temperature ("T1", 10±1˚C).
3. After moving the water into another glass vessel, place it in the center of the cooking tray. Set the oven to high
power and operate for 26 seconds for CM-1819/1829 or 33 seconds for CM-1419/1429 exactly. (3 seconds
included as a holding time of magnetron oscillation)
4. When heating is finished, stir the water again with the thermometer and measure the temperature ("T2").
5. Subtract T1 from T2. This will give you the water temperature rise. (∆T)
6. The output power is obtained by the following formula;
4.187 x 1000 x ∆T+ 0.88 x MC x (T2-T0) 23.3(29.9): Heating Time (sec)
Output Power = 4.187 : Coefficient for Water
23.3(29.9)
1000 : Water (cc)
∆T : Temperature Rise (T2-T1)
* 23.3: CM-1819/1829(1800W) MC : Cylindrical borosilicate glass weight
* 29.9: CM-1419/1429(1400W) T0 : Room temperature
D/4 D/4
D/4
Plate Tray
Samsung Electronics 21
Alignment and Adjustments
22 Samsung Electronics
6. Troubleshooting
PRECAUTION
1. CHECK GROUNDING BEFORE CHECKING FOR TROUBLE.
2. BE CAREFUL OF THE HIGH VOLTAGE CIRCUIT.
3. DISCHARGE THE HIGH VOLTAGE CAPACITOR.
4. WHEN CHECKING THE CONTINUITY OF THE SWITCHES OR TRANSFORMER, DISCONNECT
LEAD WIRES FROM THESE PARTS AND THEN CHECK CONTINUITY WITHOUT THE POWER
SOURCE ON. TO DO OTHERWISE MAY RESULT IN A FALSE READING OR DAMAGE TO YOUR
METER.
5. DO NOT TOUCH ANY PART OF THE CIRCUIT OR THE CONTROL CIRCUIT BOARD, SINCE STATIC
DISCHARGE MAY DAMAGE IT. ALWAYS TOUCH GROUND WHILE WORKING ON IT TO
DISCHARGE ANY STATIC CHARGE BUILT UP.
Samsung Electronics 23
Troubleshooting
Oven does not operate and Defective Ass'y PCB Replace Ass’y PCB.
return to plugged-in mode.
Loud buzzing noise can 1. Loose fan and ventilation motor Tighten screws of ventilation motor.
be heard. 2. Loose screws on H.V.Transformer Tighten screws of H.V.Transformer.
3. Shorted H.V.Diode Replace H.V.Diode.
4. Loose or missing screws on Tighten screws of Cover-Back
Cover-Back
Drive motor not 1. Open or loose wiring of drive motor. Check the wire of drive motor
work. (Assy stirrer 2. Defective drive motor. Replace drive motor.
does not rotate.) 3. Defective ass’y stirrer Replace ass’y stirrer.
Oven stops operating 1. Operation of thermal cutout Adjust door and latch switches.
during cooking. (Magnetron or Cavity)
2. Ventilation motor does not rotate. Replace ventilation motor.
Sparks 1. Metallic ware or cooking dishes Inform the customer of proper use.
touching on the oven wall.
2. Ceramic ware trimmed with gold or Do not use any type of cookware
silver powder also causes sparks. with metallic trimming.
Uneven cooking Uneven intensity of microwave due to Wrap thinner parts of the food with
its characteristics. aluminum foil.
Use plastic wrap or cover with a lid.
Stir once or twice while cooking
foods such as soup, cocoa, or milk.
Noise from turntable motor Noise may result from the motor. Replace turntable motor.
when it starts to operate.
Oven can program Defective circuitry of Start function Check circuitry of Start function
but timer does not of Main PCB Ass’y. of Main PCB Ass’y and replace if
start. defective.
Loose lead wires Adjust or repair loose wires.
24 Samsung Electronics
Troubleshooting
E41 1. Main Relay (RY1) or Check Main Relay (RY1), Power Relay (RY2)
Power Relay (RY2) failure Primary S/W and Monitor S/W and replace
2. Loose lead wires of relay if defective.
3. Primary or Monitor S/W Check if lead wires are loosened
failure and connect firmly if loose.
4. Loose lead wires of Primary
or Monitor S/W
5. H.V.Trans input power sensing Check the circuitry and replace if defective.
circuitry failure (Refer to Operating Sequence
as shown in page 42.)
E42 1. Power Relay (RY5) failure Check Power Relay2, Primary S/W,
2. Loose lead wires of Monitor S/W or Fuse
Power Relay (RY5) and replace if defective.
3. Primary or Monitor S/W failure Check if lead wires are loosened
4. Loose lead wires of and repair as necessary.
Primary or Monitor S/W
5. Fuse(10A) blown out
on neutral area of
Ass’y Noise Filter
6. H.V.Trans input power sensing Check the circuitry. (Refer to Operating Sequence
circuit failure as shown in page 42.)
Samsung Electronics 25
7. Exploded Views and Parts List
7-1 Exploded Views
54 1
20
21 CM-1829
CM-1429 4
30
18 3
29
18 19
11
28
31
19
CM-1819
CM-1419
22 43 12
13
(CM-1829/1429)
46
49
51
41 15 2
53
23
36
17
7
(CM-1819/1419) 44 9
8
52 6
45
42 16 47
14
48
32
40 33 38
34
35
10
25
24
33
37
5
39
27 26
50
26 Samsung Electronics
Exploded Views and Parts List
Samsung Electronics 27
Exploded Views and Parts List
28 Samsung Electronics
Exploded Views and Parts List
1
11
2
4
5
8
11
9
10
6
7
Samsung Electronics 29
Exploded Views and Parts List
13
12
11
7
10 8
4 9
3
30 Samsung Electronics
Exploded Views and Parts List
9
1 10
2
11
8
5
4
7
3
Samsung Electronics 31
Exploded Views and Parts List
32 Samsung Electronics
P.C.B Circuit Diagrams and Parts List
34 Samsung Electronics
P.C.B Diagrams and Parts List
Samsung Electronics 35
P.C.B Diagrams and Parts List
36 Samsung Electronics
P.C.B Diagrams and Parts List
Samsung Electronics 37
P.C.B Diagrams and Parts List
38 Samsung Electronics
9. Wiring Diagram & Operating Sequence
9-1 Wiring Diagram (CM-1819/1419/1829/1429)
Samsung Electronics 39
Wiring Diagram & Operating Sequence
The relation between indications on the display window and the output power of the microwave oven is as
shown in figure below.
c(d): 20% -> opt open - 7sec(8sec) 25% -> opt short - 9sec(6sec)
10% -> opt open - 4sec(11sec) 13% -> opt short - 5sec(10sec)
e: 15sec
Note: One second included as a time for starting the magnetron oscillation
40 Samsung Electronics
Wiring Diagram & Operating Sequence
Initial operating status of Power Relay when the START button is pressed.
Operating
Operating Time of Relays (100%, 70%, 50% power)
Sequence
NOTE :
LAMP: Lamp Relay (250V 5A)
MAIN: Main Relay (250V 16A)
VENT: Ventilation Motor Relay (250V 5A)
IR1: Inrush Relay1 (250V 5A)
IR2: Inrush Relay2 (250V 5A)
P1: Power Relay1 (250V 16A)
P2: Power Relay2 (250V 16A)
Samsung Electronics 41
Wiring Diagram & Operating Sequence
9-2 Description of Operating Sequence (continued)
Refers to the circuitry that detects and check if the input power is correctly supplied to the primary terminal of
High Voltage Transformer when the microwave oven is operating. If any abnormal condition(eg. Micro S/W,
Relay open) is detected, the error code (E41, E42) shows on the display window. When the error code
appears in the display window, check the waveform(A), (B), (C),or (D).
In case of Power Relay 1 (RY2), check the waveform (A), (B) below.
In case of Power Relay 2 (RY5), check the waveform (C), (D) below.
42 Samsung Electronics