Professional Documents
Culture Documents
My Rangeman PDF Manual
My Rangeman PDF Manual
My Rangeman PDF Manual
1
Operation Guide 3452
World Time
World Time City Setting
Display Illumination
Illuminating the Display Manually
Auto Light
Other Settings
Configuring Home City and Summer Time
Settings
Using Alarms
Other Information
City Table
Supported Phones
Specifications
Troubleshooting
2
Operation Guide 3452
Before Getting Note Mode Overview
Started... This section provides an overview of the
● Note that the watch illustrations in this
This section provides an overview of your manual are intended for reference modes of your watch.
watch and explains how to connect with a only. The actual watch may appear
phone. You can configure watch settings to somewhat different than depicted in ● Mode Overview
connect with a phone at preset times each day the illustrations.
GPS Navigation Mode
and adjust its time settings in accordance with
information obtained from a network time Use this mode to record routes that you travel
server. You can also change the watch’s time and to check the bearing to your destination.
settings manually and configure other watch
settings from the phone.
Button Operations You can also record your current location in
watch memory.
l GPS Navigation
Important!
3
Operation Guide 3452
Altimeter Mode Timer Mode Entering Another Mode (Other than the
Use this mode to take an altitude reading for Use this mode to countdown from a desired GPS Navigation Mode)
your current location. start time. In any mode besides the GPS Navigation
l Altitude Measurement l Timer Mode, you can navigate between modes
using the steps below.
Rotary Switch
Pointer
Sunrise/Sunset Mode
Tide/Moon Mode
Stopwatch Mode
Timer Mode
World Time Mode
Rotary Switch
Holding down the rotary switch in any mode 4. Press the rotary switch.
Tide/Moon Mode
for about one second displays the navigation
This mode displays tide levels and Moon age This enters the selected mode.
screen.
data for a location specified with the CASIO
“G-SHOCK Connected” app.
l Tide Level and Moon Age
Rotary Switch
Stopwatch Mode
Use this mode to measure elapsed time.
l Stopwatch
4
Operation Guide 3452
Charging the Watch Charging with the Charger
Note
Charging with the charger is faster than solar
● You can also return to the Timekeeping Solar Charging charging.
Mode directly from any other mode by
Power generated by the solar panel powers
holding down (C) for about one Important!
watch operations and also is used to charge a
second.
rechargeable (secondary) battery. The solar
You can also enter the Communication
● Use only the supplied charger and
panel is integrated into the LCD of the watch,
●
5
Operation Guide 3452
● Precautions When Charging Charging Time Guidelines
1. Position the watch so its right (rotary ● GPS signals (for time adjustment, log Charging each day for the approximate times
switch) side is aligned with the small claw
acquisition, point memory, etc.) are not shown below should be enough to maintain a
of the charger.
received while charging with the charger is
charge of or higher.
in progress.
● The watch’s GPS function will not be able to At a charge of , all watch functions are
be used for about one minute after you supported, except for GPS.
remove it from the charger. During that l Checking the Charge Level
period the watch also will not be able to
detect whether it is connected to or Note
disconnected from the charger.
● Do not attempt charging at high ambient ● Actual charging time depends on the
temperatures of 35°C or greater. The watch local charging environment.
Small claw
becomes hot during charging, which will
cause charging to stop. High ambient
2. Secure the left side of the watch with the temperature may result in a less than full Solar Charging
large claw of the charger. charge. Sunny day, outdoors (50,000 lux): 12 minutes/
● Do not carry the charger in a bag or day
otherwise subject it to squeezing or Sunny day, near a window (10,000 lux): 45
crushing forces. Doing so can cause minutes/day
deformation of the claws so they become Overcast day, near a window (5,000 lux): 72
open too far, making it impossible to attach minutes/day
the watch to the charger.
● If an ongoing charging operation stops, Note
Large claw remove the watch from the charger and
disconnect the USB cable. After checking ● Charging is performed even with
for and eliminating problems, try charging exposure to indoor fluorescent lighting
● Make sure that the claws of the charger
again. (500 lux). The watch will be able to
securely grasp the watch, and that the
watch is in close contact with the
● It may take some time for charging to start maintain a charge of or higher if it
charger. after the watch is attached to the charger. is exposed to indoor fluorescent
● Charging may fail if there is space
● The watch and charger may become warm lighting for eight hours a day, in
between the charger and watch. Also, during charging. This is normal and does addition to light near a window on a
foreign matter can get into the space not indicate malfunction. sunny day (10,000 lux) for two hours a
and cause overheating of the watch week.
and/or charger. Note
3. Turn on your computer or other device ● It takes about five hours for charging to Charging with the Charger
with a USB port (power source), and start after the watch’s display goes 1 minute/day
connect the USB cable to it. blank.
4. Connect the other end of the USB cable to ● Charging time depends on ambient
the charger. temperature and other factors.
Press down on the watch and charger
when connecting the USB cable to the
USB port to ensure that they do not
separate from each other.
● This starts charging and causes to
appear on the watch display.
● disappears from the display when a
full charge is achieved.
6
Operation Guide 3452
Checking the Charge Level Power Saving Function Pairing the Watch with a
You can determine the watch’s current charge Leaving the watch in a dark location in the Phone
level in any mode. Timekeeping Mode for 70 minutes or longer
between the hours of 9 p.m. and 6 a.m. will To connect the watch with a phone, first install
Charge
Indicator Usable Functions cause the watch to enter Level 1 power the CASIO “G-SHOCK Connected” app on the
level
saving. If the watch is left in this condition for phone and then use Bluetooth to pair the
six or seven days, the watch will enter Level 2 watch with the phone.
All power saving. The display of the watch goes
High blank when the watch is in power saving. ● A Install the app on your phone.
In Google Play or the App Store, search for the
All functions except those Power Saving Level 1 :
CASIO “G-SHOCK Connected” app and
that use GPS The functions below can be used while the
install it on your phone.
Timekeeping only watch is in Level 1 power saving.
Low
(Button operations ● Alarm ● B Configure Bluetooth settings.
disabled.) ● Timer Enable the phone’s Bluetooth.
● Phone connection
When the battery indicator becomes ,
Note
●
7
Operation Guide 3452
Using the Watch in a Medical Connecting the Watch with a Disconnecting from a Phone
Facility or Aircraft Phone Pressing any button will terminate a Bluetooth
connection and return to the Timekeeping
When you are in a hospital, on an aircraft, or Mode.
Connecting with a Phone
in any other location where radio signals may
Connected Disconnected
cause problems, you can perform the This section explains how to establish a
procedure below to enter the watch’s Airplane Bluetooth connection with a phone that is
Mode, which disables auto GPS signal paired with the watch.
receive and connection with a phone. To re- ● If the watch is not paired with the phone you
enable auto time adjustment, perform the want to connect with, perform the procedure
same operation again. under “C Pair the watch with a phone.” to
pair them.
1. Enter the Timekeeping Mode.
l Navigating Between Modes 1. Move the phone close to (within one meter Configuring Watch Settings
of) the watch. After establishing a connection between the
watch and a phone, you can use G-SHOCK
2. Y On the Home Screen, tap the “G-
Connected to configure watch settings and to
SHOCK Connected” icon.
view information acquired by the watch.
3. X Enter the Communication Mode.
1. Y Tap the “G-SHOCK Connected” icon.
Rotary Switch l Navigating Between Modes
● [CONNECTED] appears on the watch 2. X Enter the Communication Mode.
display appears when a connection is
2. Press (A). l Navigating Between Modes
established with the phone.
This displays the Timekeeping Mode
● [CONNECTED] appears on the watch
● [CONNECT FAILED] will appear if display appears when a connection is
setting screen.
connection fails for some reason. established with the phone.
3. Rotate the rotary switch to move the ● [CONNECT FAILED] will appear if
pointer to [AIRPLANE MODE]. Important!
connection fails for some reason.
4. Press the rotary switch. ● If you have problems establishing a 3. Y Select the setting you want to change
5. Rotate the rotary switch to select the connection, it could mean that G- and then perform the operation shown on
Airplane Mode setting. SHOCK Connected is not running on the phone screen.
the phone. On the phone’s home
[ON]: Airplane Mode enabled
screen, tap the “G-SHOCK Phone Finder
[OFF]: Airplane Mode disabled.
Connected” icon. After the app starts
6. Press the rotary switch to exit the setting up, enter the Communication Mode on You can use phone finder to trigger a tone on
screen. the watch. the phone to make it easy to find. The tone is
forced to sound even if the phone is in vibrate
This returns to the Timekeeping Mode
mode.
setting screen.
Note Important!
7. Press (C) to exit the setting screen.
● is displayed while the watch is in the ● The connection will be terminated if ● Do not use this function in areas where
Airplane Mode. you do not perform any operation on
phone call tones are restricted.
the watch or phone for a fixed amount
● The tone sounds at a high volume. Do
of time.
not use this function when listening to
To specify the connection limit time,
phone output over earphones.
perform the following operation with G-
SHOCK Connected: “Watch settings”
n “Connection time”. Next, select a
setting of 3 minutes, 5 minutes, or 10 1. X Enter the Timekeeping Mode.
minutes. l Navigating Between Modes
Rotary Switch
8
Operation Guide 3452
2. X Press (D).
Adjusting the Time Appropriate Signal Reception
Location
Setting
3. X Rotate the rotary switch to move the GPS signal reception is possible outdoors
pointer to [PHONE FINDER]. Your watch can receive GPS signals and where the sky is visible and not blocked by
connect with a phone to obtain information buildings, trees, or other objects.
4. X Press the rotary switch. that it uses to adjust its date and time setting.
This will establish a connection between Getting ready
the watch and phone, and sound the
Enter the Timekeeping Mode.
phone’s ringtone.
l Navigating Between Modes
● It will take a few seconds before the
phone tone sounds.
near a window.)
GPS Time Adjustment ー Near wireless communication
9
Operation Guide 3452
Acquiring GPS Position Information Acquiring GPS Time Information
Manually Note Manually
You can use a button operation to acquire ● Receive normally takes anywhere You can use a button operation on the watch
GPS location information and adjust your time from about 40 to 80 seconds. to receive GPS signal time information. When
zone, time, and day settings in accordance the receive operation is successful, the
● It can take as long as 13 minutes when
with your current location. watch’s Home City (time zone), day, and time
leap second information is included.
settings will be adjusted accordingly.
Note
● You may experience location
information acquisition problems when Note
● GPS signal reception requires large you are in the vicinity of a city
amounts of power. Perform it only borderline. ● GPS signal reception requires large
when necessary. The watch’s time and day will not be amounts of power. Perform it only
indicated correctly if the time zone when necessary.
setting is not right for your location. If
this happens, move to a location near
1. Move to a location appropriate for signal the center of the city you want to set as
reception and point the LCD of the watch your Home City and acquire location 1. Move to a location appropriate for signal
straight up at the sky. information again. Or you can perform reception and point the LCD of the watch
a time information receive operation to straight up at the sky.
2. Press (D).
adjust time and day settings after 2. Hold down (D) for about 1.5 seconds.
configuring Home City and summer
This starts time information acquisition.
time settings manually.
l Acquiring GPS Time Information
Manually
l Configuring Home City and
Summer Time Settings
Rotary Switch
● [RECEIVING FAILED] will appear on ● You can also trigger a time information
the display if location information receive operation manually by
acquisition fails for some reason. performing the steps below.
10
Operation Guide 3452
Receiving Time Information Signal Reception Precautions Connecting with a Phone to
Automatically ● When the watch is unable to adjust its time Adjust the Watch’s Time
When the conditions below are satisfied, the in accordance with a GPS signal for some
watch will automatically receive time reason, average timekeeping accuracy is You can configure watch settings to connect
information from a GPS signal. If any time within ±15 seconds per month. with a phone at preset times each day and
information receive operation is successful, ● Note that an internal decoding process the adjust its time settings in accordance with
the watch will no longer attempt to receive a watch performs after it receives a GPS information obtained from an online time
signal for the rest of the day. signal may cause the time setting to be server.
● In the Timekeeping Mode slightly off (by less than one second). ● Using Auto Adjust
● Current time is between 6:00 a.m. and ● GPS signal reception is not possible under Your watch adjusts its time setting four times
10:00 p.m. the conditions described below. a day according to a preset schedule. It
● Light (near a window on a clear day) ー While the battery indicator is or lower performs the adjustment operation
continually shining on the LCD of the watch ー In any mode besides the Timekeeping automatically as you go about your daily life,
for about one to two minutes. Mode without any operation required by you.
ー During power saving
progress 12:30
ー Watch is connected with a phone
● The time information receive operation
ー Navigation log data acquisition operation
normally takes anywhere from about
10 to 65 seconds. in progress
ー Timer countdown operation in progress
● The receive operation can take as long
as 13 minutes when leap second ● If the receive operation is successful, the
information is included. time and day settings will be adjusted
automatically in accordance with the Home
City (time zone) and summer time settings.
Leap Second Reception Summer time will not be applied correctly in
Important!
the cases described below.
GPS signal reception each year on June 1 or ー When the summer time start date and
later and on December 1 or later also receives ● The watch may not be able to perform
time, end date and time, or other rules are
leap second information. auto time adjustment under the
changed by authorities
ー When location information is received,
conditions described below.
ー During a timer countdown operation
Note but it is not location information for your
actual location (For example, when you
ー While the battery indicator is or
● It can take as long as 13 minutes to are near a borderline of a city and the lower
complete the leap second information acquired location information is for a ー While the watch is too far away from
11
Operation Guide 3452
Note Checking Time Adjustment GPS Navigation
History You can use the GPS Navigation Mode to
● If there is a World Time City specified
receive GPS signals and record the routes you
with G-SHOCK Connected, its time will You can use the procedure below to check the
travel. You can also specify a destination and
also be synchronized automatically. history of time adjustments based on GPS
obtain navigation information to your
signal reception or connection with a phone.
● The watch will connect with the phone destination point.
and perform auto time adjustment at
1. Press (D). Getting ready
around 12:30 a.m., 6:30 a.m., 12:30
p.m. and 6:30 p.m. The connection is Enter the GPS Navigation Mode.
automatically terminated after auto l Navigating Between Modes
time adjustment is complete.
● GPS signal auto receive will be
performed if there has been no auto
time adjustment based on connection
Rotary Switch
between the watch and phone for more
than one day.
2. Rotate the rotary switch to move the
pointer to [HISTORY].
● Triggering Immediate Time Adjustment
3. Press the rotary switch. Important!
The watch will immediately synchronize its
This displays a menu of time adjustment
time setting automatically to that of a network
dates and times. ● Navigation displays general route
time server whenever a connection is
guidance up to a destination. It does
established between it and a phone. To trigger 4. Rotate the rotary switch to move the not display detailed route guidance like
synchronization of the watch’s time setting pointer to the date and time of the details a car navigation system does.
with a network time server manually, perform you want to check.
the procedure below.
● When using navigation, also be sure to
5. Press the rotary switch. navigate in accordance with actual
1. Press (D). This displays information acquired by the local road and other conditions.
watch. ● The navigation function is not intended
for use while in motion in an automobile
6. Press (C) to exit the setting screen. or other type of vehicle.
Note
Rotary Switch
● To set a destination that is not a
2. Rotate the rotary switch to move the waypoint in point memory, use G-
pointer to [BLUETOOTH]. SHOCK Connected.
l Registering Your Current Location
3. Press the rotary switch.
● Routes acquired with the GPS
When a connection is established with the
Navigation Mode can be transferred to
phone, the information acquired from the
a phone for viewing.
phone appears on the watch display.
● GPS navigation can be used only
when the battery indicator shows
or higher.
Rotary Switch
12
Operation Guide 3452
● Interpreting GPS Navigation
Using Navigation Note
Information
Used Unused
Note
13
Operation Guide 3452
Changing the Display Scale Returning to a Start Point Deleting a Destination
The scale of the navigation screen can be
(Backtrack) Deleting the destination will stop route
increased to show more details about a route, At any time during a navigation operation, you guidance, but continue route recording.
and to determine the direction to a target point can reverse your route to navigate back to ● For information about setting a destination,
from a start point or another point. your start point. refer to the information below.
l Setting a Registered Point as the
1. While a navigation operation is in Current location Start point
Destination
progress, press the rotary switch.
This enables adjustment of the scale. 1. While a navigation operation is in
progress, press (D).
14
Operation Guide 3452
● To change the icon assigned to a
2. Rotate the rotary switch to select whether
Viewing Registered Points
registered point
or not you want to assign an icon to the
You can use the procedure below to display
point you recorded. 1. While point details are displayed, press
details about registered points. You can also
[YES]: Assigns an icon. the rotary switch.
change icons assigned to points and delete
[NO]: Cancels icon registration. points as required.
B Rotate the rotary switch to select 2. Rotate the rotary switch to move the 4. Press (C) as many times as necessary to
whether or not you want to save the pointer to [RECALL]. return to the GPS Navigation Mode setting
current settings. screen.
3. Press the rotary switch.
[YES]: Registers the currently selected ● To protect a registered point
icon. 4. Rotate the rotary switch to move the
A protected point cannot be deleted.
pointer to [POINT].
[NO]: Cancels icon registration.
While the menu of locations is displayed
C Press the rotary switch. 5. Press the rotary switch.
This displays a menu of dates and times
5. Press the rotary switch to exit the setting
that points were registered.
screen.
This assigns the icon you selected to the
point you recorded.
Rotary Switch
Note
● In place of step 1 of the above Rotary Switch 1. Rotate the rotary switch to move the
procedure, you could perform the pointer to the date and time of the point
steps below to register your current you want to protect.
6. Rotate the rotary switch to move the
location.
pointer to the date and time of the point 2. Press (D).
A While a navigation operation is in you want to check.
This protects the selected point.
progress, press (C).
7. Press the rotary switch. A protected point is indicated by .
B Rotate the rotary switch to move the
This displays details about the selected
pointer to [POINT MEMORY]. ● Press (D) again to unprotect.
point.
C Press the rotary switch. 3. Press (C) as many times as necessary to
return to the GPS Navigation Mode setting
screen.
15
Operation Guide 3452
While the details of a particular point are Editing the Navigation Use
displayed 1. If a navigation operation is in progress,
stop it. History
l Stopping Navigation
You can protect and delete navigation logs as
2. Press the rotary switch. required.
1. While the menu of registered points or the 6. Press the rotary switch.
details of a particular registered point is 3. Rotate the rotary switch to move the
displayed, press (A).
7. Rotate the rotary switch to move the pointer to [RECALL].
pointer to [POINT RECALL].
4. Press the rotary switch.
8. Press the rotary switch.
5. Rotate the rotary switch to move the
9. Rotate the rotary switch to move the pointer to [ACTIVITY].
pointer to the point you want to specify as
your destination. 6. Press the rotary switch.
Rotary Switch ● Selecting [RESET] deletes the currently This displays a list of dates and times that
specified destination. navigation was used.
2. Rotate the rotary switch to select a delete 10. Press the rotary switch.
method.
11. Rotate the rotary switch to move the
[ONE]: Deletes only the currently selected
pointer to [YES].
point.
[ALL]: Deletes all points. 12. Press the rotary switch.
The message [SETTING COMPLETED]
3. Press the rotary switch.
will appear after the destination is set.
● To protect a log
This deletes the point(s). After a few seconds, the GPS Navigation
A recorded log that is protected cannot be
● If you selected [ALL], press the rotary Mode setting screen will re-appear.
deleted.
switch again to delete. Delete will also
13. Rotate the rotary switch to move the
be executed automatically after about
pointer to [NAVIGATION].
10 seconds, even if you do not press the
rotary switch again. 14. Press the rotary switch.
4. Press (C) as many times as necessary to This starts navigation.
return to the GPS Navigation Mode setting
screen. Note
16
Operation Guide 3452
● To delete a log
7. Rotate the rotary switch to display the
Digital Compass
1. Press (A). GPS receive interval you want to use. You can use the Digital Compass Mode to
[NORMAL]: Acquires location information determine the direction of north, and to check
every minute. your bearing to a destination.
[HIGH RATE]: Acquires location
information every few seconds. Important!
8. Press the rotary switch. ● Check the information below to find out
Rotary Switch how to ensure correct readings.
9. Press (C) as many times as necessary to
return to the GPS Navigation Mode setting l Calibrating Compass Readings
2. Rotate the rotary switch to select a delete screen. l Digital Compass Reading
method. Precautions
[ONE]: Delete only the currently selected Note
log.
Getting ready
[ALL]: Delete all logs.
● The amount of time that navigation can
Enter the Compass Mode.
be used depends on the receive
3. Press the rotary switch. interval setting. When you want to l Navigating Between Modes
This deletes the log(s). perform long-term continual
● If you selected [ALL], press the rotary navigation, select the [NORMAL]
switch again to delete. Delete will also setting.
be executed automatically after about [NORMAL]: 24 hours, continuous
10 seconds, even if you do not press the [HIGH RATE]: 4 to 5 hours, continuous
rotary switch again.
3. Rotate the rotary switch to move the 8. Press the rotary switch. North
pointer to [SETTING]. Bearing angle to Bearing to objective
9. Press (C) to return to the GPS Navigation objective
4. Press the rotary switch. Mode setting screen.
Directions: N (North), E (East), W (West), S
5. Rotate the rotary switch to move the (South)
pointer to [INTERVAL].
17
Operation Guide 3452
Note Saving a Bearing to a Clearing a Recorded Bearing
Destination (Bearing
Hold down (A) for about one second to clear
● Normally the Compass Mode Memory) a recorded bearing.
indicates magnetic north. You can also
configure settings to indicate true You can use the procedure below to record the
north. Note
direction to a destination and then use the
l Setting Up for True North recorded direction as a bearing guide.
Readings (Magnetic Declination
● You can also clear a recorded bearing
Calibration) 1. Keeping the watch level, point 12 o’clock by performing the steps below.
l Magnetic North and True North in the direction of the target destination. A Press (A).
● After the initial reading is displayed, the B Rotate the rotary switch to move the
watch will continue to take readings pointer to [BEARING MEMORY].
about every second for about the next Direction to destination
60 seconds. The watch will return to C Press the rotary switch.
the Timekeeping Mode automatically D Rotate the rotary switch to move the
about 60 seconds after you start a pointer to [RELEASE].
direction reading operation. 2. Hold down (A) for about one second. E Press the rotary switch.
● If an alarm or other beeper sounds, or This displays the bearing angle and
if you turn on illumination by pressing direction to the destination.
(B) while a compass operation is in
progress, the compass operation will
be paused momentarily. The compass
operation will resume when the beeper
stops or illumination turns off.
18
Operation Guide 3452
Calibrating Compass 7. Turn the watch over so the LCD is pointing 1. Press (A).
Readings at the ground. This displays the Digital Compass Mode
setting screen.
Perform calibration whenever you notice the
watch’s compass readings are different from
those of another compass, or before setting
out on a climb or trek.
● Note that accurate compass readings
and/or calibration will not be possible in an
Ground
area where strong magnetism is present.
Rotary Switch
l Digital Compass Reading Precautions
8. While keeping the watch horizontal, press
1. Press (A). (D). 2. Rotate the rotary switch to move the
This displays the Digital Compass Mode This starts calibration of the third point, pointer to [MAGNETIC DECLINATION].
setting screen. which causes [PLEASE WAIT] to appear
3. Press the rotary switch.
on the display. [SUCCESSFUL] will
appear when calibration is successful. A 4. Rotate the rotary switch to configure the
few seconds later, the watch will return to magnetic declination direction and angle
the Digital Compass screen. settings.
Setting range: 90° west to 90° east
Note
[0° (OFF)]: Magnetic north
Readings (Magnetic
Declination Calibration)
Rotary Switch
If you want the watch to indicate true north
4. While keeping the watch horizontal, press instead of magnetic north, you need to specify
(D). the current magnetic declination direction Magnetic declination angle
(east or west) and declination angle.
This starts calibration of the first point,
l Magnetic North and True North ● To cancel the setting operation, perform
which causes [PLEASE WAIT] to appear
The magnetic declination angle value can the steps below.
on the display. [ROTATE 180°] will appear
●
when calibration is successful. be set in 1° (degree) units only. Use a value A Press (C).
that is closest to the angle you want to set.
5. Keeping the LCD of the watch pointing B Rotate the rotary switch to select
Example: For an angle of 7.4°, set 7°.
upwards, rotate it 180 degrees. Be as whether or not you want to save the
Example: For an angle of 7°40’ (7 degrees,
exact as possible. current settings.
40 minutes), set 8°.
[YES]: Current settings saved
Note [NO]: Current settings not saved
● Pressing (C) enables configuration of
● Magnetic declination angles (east or the magnetic declination direction and
west) and angle degree values for angle settings.
specific locations can be found on
C Press the rotary switch.
geographic maps, mountain climbing
maps, and other maps that include 5. Press the rotary switch to exit the setting
contour lines. screen.
6. While keeping the watch horizontal, press
(D). This returns to the Digital Compass Mode
setting screen.
This starts calibration of the second point,
which causes [PLEASE WAIT] to appear 6. Press (C) to exit the setting screen.
on the display. [TURN OVER] will appear
when calibration is successful.
19
Operation Guide 3452
Magnetic North and True Altitude Measurement Getting ready
When using navigation while receiving l Setting the Auto Measurement Interval
Digital Compass Reading
●
Exposure of the watch to magnetism can ● The altitude correction value and
②
affect the accuracy of digital compass barometric pressure changes may
readings. Keep the watch away from the types result in display of a negative value.
of items below. ● Check the information below to find out
Permanent magnets (magnetic accessories, about how to minimize differences
between readings produced by the Graph Screen
etc.), metal objects, electrical household
appliances (TVs, computers, cellphones, etc.) watch, and values provided by local
altitude (elevation) indications.
②
l Altitude Reading Precautions
③
20
Operation Guide 3452
A Differential between reference altitude Note 1. Press (A).
and current altitude This displays the Altimeter Mode setting
● In place of step 3 of the above
screen.
B Current location altitude procedure, you could perform the
steps below to make the altitude
C Altitude graph differential ±0 m (±0 feet).
A Press (A).
200 m
Rotary Switch
Current reading
Current location altitude ー Changes in temperature caused by [NO]: Current settings not saved
variations in barometric pressure and by C Press the rotary switch.
● When the altitude differential you found elevation
on the map is the same as that 7. Press the rotary switch to exit the setting
● Though altitude readings can be taken
displayed by the watch, it means you screen.
without calibration, doing so may produce
are close to your destination. This completes the calibration
readings that are very different from
●
21
Operation Guide 3452
Setting the Auto Specifying Display Contents Specifying the Altitude
Measurement Interval Measurement Unit
You can use the procedure below to display
You can select an auto measurement interval an altitude graph in the Altimeter Mode. You can select either meters (m) or feet (ft) as
of either five seconds or two minutes. the Altimeter Mode display unit.
1. Press (A).
1. Press (A). Important!
This displays the Altimeter Mode setting
screen. ● When Tokyo (TOKYO) is the Home
City, the altitude unit is fixed as meters
(m) and cannot be changed.
Rotary Switch
1. Press (A).
2. Rotate the rotary switch to move the
This displays the Altimeter Mode setting
Rotary Switch pointer to [SCREEN].
screen.
3. Press the rotary switch.
2. Rotate the rotary switch to move the
pointer to [INTERVAL]. 4. Rotate the rotary switch to select a display
format.
3. Press the rotary switch. [VALUE]: Displays the latest
4. Rotate the rotary switch to select the auto measurement value only.
measurement interval you want to use. [GRAPH]: Displays a measurement value Rotary Switch
[2 MINUTES]: Readings taken every and an altitude graph.
second for the first three minutes, and 5. Press the rotary switch to exit the setting 2. Rotate the rotary switch to move the
then every two minutes for about 12 screen. pointer to [UNIT].
hours.
This returns to the Altimeter Mode setting 3. Press the rotary switch.
[5 SECONDS]: Readings taken every screen.
second for the first three minutes, and 4. Rotate the rotary switch to select the
then every five seconds for about one 6. Press (C) to exit the setting screen. altitude unit.
hour.
[METER]: Meters
5. Press the rotary switch to exit the setting [FEET]: Feet
screen.
5. Press the rotary switch to exit the setting
This returns to the Altimeter Mode setting
screen.
screen.
This returns to the Altimeter Mode setting
6. Press (C) to exit the setting screen. screen.
22
Operation Guide 3452
Altitude Reading Barometric Pressure Barometric Pressure Graph Screen
The graph shows barometric readings taken
Precautions and Temperature every two hours. You can use the graph to
Effects of Temperature Measurement view changes in barometric pressure over the
past 48 hours, which can be used to predict
When taking altitude readings, take the steps You can use the watch to take barometric upcoming weather.
below to keep the watch at as stable a pressure and temperature readings for your
temperature as possible. Changes in current location. Barometric pressure graph
temperature can affect altitude readings. Barometric pressure
● Take readings with the watch on your wrist. Important!
● Take readings in an area where
temperature is stable. ● Check the information below to find out
how to ensure correct readings.
Altitude Readings
l Barometric Pressure and
● Do not use this watch while skydiving, hang Temperature Reading Temperature
gliding, paragliding, gyrocopter flying, glider Precautions
flying, or engaged in other activities where
A trend
altitude changes suddenly. Indicates this:
like this:
● Altitude readings produced by this watch Getting ready
Rising barometric pressure,
are not intended for special-purpose or Enter the Barometer/Temperature Mode.
which indicates that upcoming
industrial level use. l Navigating Between Modes
weather probably will be fair.
● In an aircraft, the watch measures the in- l Changing Displayed Information
Falling barometric pressure,
cabin pressurized air pressure, so readings
which indicates that upcoming
will not match altitudes announced by the
weather probably will be bad.
crew.
23
Operation Guide 3452
Barometric Pressure Change Note Calibrating Barometric
Indicator Pressure Readings
● You can also enable the barometric
Each time (A) is held down for about one pressure change indicator by The watch’s pressure sensor is adjusted at the
second, the barometric pressure change performing the steps below. factory and normally does not require
indicator will toggle between enabled and calibration. However, you can calibrate the
A Press (A).
disabled. While the barometric pressure displayed value if you notice major errors in
change indicator is enabled, the watch will B Rotate the rotary switch to move the readings.
beep to alert you whenever it detects a pointer to [BARO INFORMATION].
significant change in air pressure readings
C Press the rotary switch. Important!
(due to sudden altitude change, or to the
passage of a high or low pressure area). D Rotate the rotary switch to select ● The watch will not be able to produce
● While the barometric pressure change the barometric pressure change correct barometric pressure readings if
indicator is enabled, the [BARO] indicator is indicator setting you want. you make a mistake during the
displayed along with one of the indicators [ENABLE]: Barometric pressure calibration procedure. Check to make
below. change indicator enabled sure that the value you use for
[DISABLE]: Barometric pressure calibration produces correct pressure
This readings.
Means this: change indicator disabled
indicator:
E Press the rotary switch.
Sudden drop in pressure ● If the barometric change indicator is
1. Press (A).
enabled, readings are taken every two
minutes even while the watch is not in This displays the Barometer/
Sudden rise in pressure
the Barometer/Temperature Mode. Temperature Mode setting screen.
● The barometric pressure change
Sustained rise in pressure,
indicator becomes disabled
shifting to a fall
automatically 24 hours after it is
Sustained fall in pressure, shifting enabled.
to a rise ● Time adjustment using GPS signal
reception or phone connection is
Rotary Switch
Important! disabled while the barometric pressure
change indicator is enabled. Power
saving is also disabled. 2. Rotate the rotary switch to move the
● To ensure correct barometric pressure
l Power Saving Function pointer to [CALIBRATION].
change indicator operation, enable it in
a location where the altitude is ● The barometric pressure change 3. Press the rotary switch.
constant (such as a lodge, camp area, indicator will become disabled
or on the ocean). automatically when the battery 4. Rotate the rotary switch to move the
pointer to [BAROMETER].
● A change in altitude causes a change becomes or lower.
in air pressure. Because of this, correct 5. Press the rotary switch.
readings are impossible. Do not take
readings while ascending or 6. Rotate the rotary switch to move the
descending a mountain, etc. pointer to [MANUAL].
● Selecting [OFFSET OFF] returns
barometric pressure calibration to its
factory default state.
24
Operation Guide 3452
8. Repeat the steps below to change the
Calibrating Temperature 7. Press the rotary switch.
value. Readings
8. Repeat the steps below to change the
● Rotate the rotary switch to change the value.
The watch’s temperature sensor is adjusted at
underlined value.
the factory and normally does not require ● Rotate the rotary switch to change the
● Use (D) to move the underlining to the calibration. However, you can calibrate the value or the sign where the underlining
value you want to change. displayed value if you notice major errors in is located. To specify a sub-zero value,
readings. display the minus (-) sign.
● Use (D) to move the underlining to the
Important!
value you want to change.
Rotary Switch
25
Operation Guide 3452
4. Rotate the rotary switch to select a display
Specifying the Temperature Barometric Pressure and
format. Unit Temperature Reading
[VALUE]: Displays the latest Precautions
You can select either Celsius (°C) or
measurement value only.
Fahrenheit (°F) as the temperature display ● Barometric Pressure Reading
[GRAPH]: Displays a measurement value unit. Precautions
and a barometric pressure graph
● The barometric pressure graph produced
5. Press the rotary switch to exit the setting Important!
by this watch can be used to obtain an idea
screen. of upcoming weather conditions. However,
● When Tokyo (TOKYO) is set as the
This returns to the Barometer/ this watch should not be used in place of
Home City, the temperature unit is
Temperature Mode setting screen. precision instruments required for official
fixed as Celsius (°C) and cannot be
weather prediction and reporting.
6. Press (C) to exit the setting screen. changed.
● Pressure sensor readings can be affected
by sudden changes in temperature.
Because of this, there may be some error in
Specifying the Barometric 1. Press (A). the readings produced by the watch.
Pressure Unit This displays the Barometer/
● Temperature Reading Precautions
Temperature Mode setting screen.
You can specify either hectopascals (hPa) or Body temperature, direct sunlight, and
inches of mercury (inHg) as the display unit for humidity all have an effect on temperature
barometric pressure values. readings. To help ensure more accurate
temperature readings, remove the watch from
Important! your wrist, wipe it dry of any moisture, and
place it in a well-ventilated location not
● When Tokyo (TOKYO) is set as the Rotary Switch exposed to direct sunlight. You should be able
Home City, the barometric pressure to take temperature readings after about 20 to
unit is fixed as hectopascals (hPa) and 30 minutes.
2. Rotate the rotary switch to move the
cannot be changed. pointer to [UNIT].
26
Operation Guide 3452
Looking Up Today’s Sunrise Tide Level and Moon Checking the Current Tide
and Sunset Times Age Level and Moon Age
Entering the Sunrise/Sunset Mode displays You can also specify a city with G-SHOCK Entering the Tide/Moon Mode, displays the
today’s sunrise and sunset times for your Connected and then use the watch to display tide and Moon age at 6:00 a.m. in the city that
Home City. the tide level and Moon age there. you specified with G-SHOCK Connected.
● Pressing (D) displays the next day’s sunrise ● Rotating the rotary switch scrolls through
and sunset times. Important! displayed tide information at one-hour
intervals.
Sunrise time ● Displayed information is intended for ● Pressing (D) displays information for the
reference only. Do not use it for next day.
maritime navigation, etc.
● When looking up a tide level or Moon
age, use G-SHOCK Connected to ④
① ⑤
select the city whose information you
② ⑥
Sunset time want to look up. Entering the Tide/
③
Moon Mode while there is no city
selected will cause the message [SET
IN THE APP] to appear. This function
Looking Up Sunrise and cannot be used until a city is selected.
A High tide
Sunset Times by Specifying a
Day Getting ready B Tide at the specified date and time
Enter the Tide/Moon Mode.
C Specified date and time
1. Hold down (D) for about one second. l Navigating Between Modes
This causes the year to become D City name
underlined.
E Moon age on the specified date
F Low tide
Tide Cycle (Three Patterns)
2. Rotate the rotary switch to change the ● The tide level and Moon age display is Large Moderate Small
year setting. based on the summer time setting of difference difference difference
the city that is set when you enter the between high between high between high
3. Press (D). tide and low tide and low tide and low
Tide/Moon Mode.
This moves the underlining to the month. tide tide tide
5. Press (D).
This moves the underlining to the day.
27
Operation Guide 3452
Checking the Tide Level and Adjusting High Tide Times Specifying Your Hemisphere
Moon Age for a Specific Day
You can improve the accuracy of the How the face of the Moon appears (bright part
You can specify a day to look up the tide level displayed high tide by adjusting the high tide to the left or right) depends on whether you are
and Moon age on that day. time in accordance with information available viewing it from Northern Hemisphere or
on the internet or in a newspaper. Southern Hemisphere. You can specify your
1. Hold down (D) for about one second. hemisphere so the watch displays Moon
1. Press (A). phases as they actually appear in your
This causes the year to become
underlined. This displays the Tide/Moon Mode setting location.
screen.
1. Press (A).
This displays the Tide/Moon Mode setting
screen.
Rotary Switch
Rotary Switch
28
Operation Guide 3452
Stopwatch Measuring a Split Time Setting a Start Time
The stopwatch can be used to perform 1-
Use the operations below to measure elapsed 1. Hold down (A) for about two seconds, or
second elapsed time measurement up to 999
time. press (A) and then press the rotary switch.
hours, 59 minutes, 59 seconds.
Start This causes the hours to become
It can also measure split times.
underlined.
Getting ready
Split
Enter the Stopwatch Mode.
l Navigating Between Modes
Split release
Stop
Rotary Switch
Stop
Resume
Stop
29
Operation Guide 3452
Using the Timer World Time City Setting Configuring the Summer
Time Setting
Use the procedure in this section to select a
1. Press (D) to start the countdown.
World Time city.
1. Press (A).
1. Hold down (A) for about two seconds. This displays the World Time Mode
This displays a menu of World Time setting screen.
Cities.
Note
Note
● The initial factory default summer time
● In place of step 1 of the above setting for all cities is [AT (AUTO)]. In
procedure, you could perform the many cases, the [AT (AUTO)] setting
steps below to display the World Time lets you use the watch without
City menu. switching between summer time and
A Press (A) to display the World Time standard time.
Getting Ready Mode setting screen. ● While [UTC] is selected as the city, you
will not be able to change or check the
Enter the World Time Mode. B Rotate the rotary switch to move the
summer time setting.
l Navigating Between Modes pointer to [WORLD TIME].
C Press the rotary switch.
Note
30
Operation Guide 3452
Display Illumination Note Specifying the Illumination
You can illuminate the display by pressing a
Duration
● Auto Light is disabled when any one of
button. The watch also has an auto light
the conditions below exists. You can select either 1.5 seconds or three
function that automatically illuminates the
ー Alarm, timer alert, or other beeper seconds as the illumination duration.
display whenever the watch is angled towards
sounding
your face for reading. 1. Enter the Timekeeping Mode.
ー While a GPS signal is being received
31
Operation Guide 3452
Other Settings ● Configuring the Summer Time Setting
Manual Time Adjustment
If you are in an area that observes summer
Getting ready time, you can also enable or disable summer You can use the procedure below to adjust the
Enter the Timekeeping Mode. time. watch’s time and day settings when GPS
l Navigating Between Modes signal reception or communication with a
Note phone is not possible for some reason.
If you move to another time zone, you can receive operation is different from 2. Rotate the rotary switch to move the
have the watch indicate the current time there the watch’s time zone setting prior to pointer to [TIME&DATE].
by simply changing the Home City and the receive operation.
summer time settings. ー When the time zone is unchanged, 3. Press the rotary switch.
but the acquired position information
● Setting a Home Time City 4. Use the operations below to configure the
is for a geographic area with
Use the procedure in this section to select a time and date settings.
different summer time rules (start
city to use as your Home City. date, end date)
● Rotate the rotary switch to change the
underlined value.
1. Press (A). ● Use (D) to move the underlining
This displays the Timekeeping Mode between values. Each press of (D)
1. Press (A).
setting screen. moves the underlining in the following
sequence: hour n minute n year n
month n day.
Note
32
Operation Guide 3452
Changing the Timekeeping TIME+WORLD TIME: Current Time + Switching between 12-hour and 24-
World Time hour Timekeeping
Mode Display Configuration
You can specify either 12-hour format or 24-
Changing Displayed Information hour format for the time display.
TIME+BAROMETER: Current Time + 7. Press the rotary switch to exit the setting
Barometric Pressure 2. Rotate the rotary switch to move the screen.
While this screen is selected, entering the pointer to [DISPLAY]. This returns to the Timekeeping Mode
Timekeeping Mode will cause the current setting screen.
3. Press the rotary switch.
barometric pressure value and a graph of the
8. Press (C) to exit the setting screen.
last 12 hours of barometric pressure readings 4. Rotate the rotary switch to move the
to be shown at the top of the display for one pointer to [SCREEN].
● While 12-hour timekeeping is selected,
hour. After one hour, only a graph of the last [P] will be displayed for p.m. times.
48 hours of barometric pressure readings
5. Press the rotary switch.
(without the current value) will be shown. 6. Rotate the rotary switch to move the
First 12 hours After 12 hours pointer to the setting you want. Using Alarms
7. Press the rotary switch to exit the setting The watch will beep when the alarm time is
screen. reached. You can set up to four different
This returns to the Timekeeping Mode alarms.
setting screen. ● When snooze is enabled for an alarm, it will
8. Press (C) to exit the setting screen. sound every five minutes up to seven times.
● The beeper is muted in the cases described
below.
TIME+SUNRISE: Current Time + Sunrise/
ー While the battery indicator is or lower
Sunset Times
ー When watch is at Level 2 power saving
l Power Saving Function
33
Operation Guide 3452
● To configure alarm settings ● To turn an alarm on or off
Enabling the Button
1. Press (A). 1. Press (A). Operation Tone
This displays the Timekeeping Mode This displays the Timekeeping Mode
Use the procedure below to enable or disable
setting screen. setting screen.
the tone that sounds when you press a button.
1. Press (A).
This displays the Timekeeping Mode
setting screen.
2. Rotate the rotary switch to move the 2. Rotate the rotary switch to move the
pointer to [ALARM]. pointer to [ALARM].
Rotary Switch
3. Press the rotary switch. 3. Press the rotary switch.
4. Rotate the rotary switch to move the 4. Rotate the rotary switch to move the 2. Rotate the rotary switch to move the
pointer to the alarm whose setting you pointer to the alarm whose setting you pointer to [BEEP].
want to change. want to change.
3. Press the rotary switch.
5. Press the rotary switch. 5. Press (D) to the alarm where the pointer is
located between on and off. 4. Rotate the rotary switch to move the
6. Rotate the rotary switch to change the pointer to [ON] (enabled) or [OFF]
hour setting. Turning on an alarm causes to
(disabled).
● To cancel an alarm time setting, appear on the display to the right of the
perform the steps below. time setting. If snooze is turned on, [SNZ] 5. Press the rotary switch to exit the setting
also appears. screen.
A Press (C).
This returns to the Timekeeping Mode
6. Press (C) as many times as necessary to
B Rotate the rotary switch to select setting screen.
exit the setting screen.
whether or not you want to save the ● is displayed in the Timekeeping
current settings. ● To stop a sounding alarm
Mode while the operation tone is
[YES]: Current settings saved Pressing any button while the beeper is disabled.
[NO]: Current settings not saved. sounding stops it.
6. Press (C) to exit the setting screen.
C Press the rotary switch.
Note
7. Press (D).
● When snooze is enabled for an alarm,
8. Rotate the rotary switch to change the it will repeat every five minutes, up to
minute setting.
seven times. To stop an alarm’s
9. Press (D). ongoing snooze operation, turn off the
alarm.
10. Rotate the rotary switch to turn snooze on ● The alarm beeper sound may be
or off.
distorted if a navigation operation is in
11. Press the rotary switch. progress.
This turns on the alarm whose time setting
you configured.
● Turning on an alarm causes to
appear on the display to the right of the
time setting. If snooze is turned on,
[SNZ] also appears.
34
Operation Guide 3452
Other Information ● The information in the above table is current
as of July 2017. City Name
Summer Time Summer Time
Start End
This section provides non-operational ● Time zones may change and UTC 02:00, last
information you also need to know. Refer to differentials may become different from 01:00, last
London Sunday in
this information as required. Sunday in March
those shown in the table above. If this October
happens, connect the watch with a phone 03:00, last
City Table to update the watch with the latest time zone Paris
02:00, last
Sunday in
Sunday in March
information. October
City Offset 04:00, last
03:00, last
Coordinated Athens Sunday in
UTC 0 Sunday in March
Universal Time October
Summer Time Table
LONDON London 0 00:00,
00:00, March 22
PARIS Paris +1 Tehran September 22 or
When “AT (AUTO)” is selected for a city that or 21
21
ATHENS Athens +2 observes summer time, switching between
02:00, first
JEDDAH Jeddah +3 standard time and summer time will be Sydney, 03:00, first
Sunday in
TEHRAN Tehran +3.5 performed automatically at the timing shown Adelaide Sunday in April
October
DUBAI Dubai +4 in the table below.
02:00, first
Lord Howe 02:00, first
KABUL Kabul +4.5 Sunday in
Note Island Sunday in April
KARACHI Karachi +5 October
DELHI Delhi +5.5 02:00, last
If the summer time start and end dates 03:00, first
KATHMANDU Kathmandu +5.75
●
Wellington Sunday in
Sunday in April
for your current location have been September
DHAKA Dhaka +6
changed, they may be different from 02:45, last
YANGON Yangon +6.5 Chatham 03:45, first
those indicated in the table below. If Sunday in
BANGKOK Bangkok +7 Islands Sunday in April
this happens, you can have new September
HONG KONG Hong Kong +8 summer time information for your 02:00, first 03:00, third
PYONGYANG Pyongyang +8.5 Home City and World Time city sent to Nuku’alofa Sunday in Sunday in
EUCLA Eucla +8.75 the watch by connecting the watch with November January
TOKYO Tokyo +9 a phone. If you cannot connect with a 02:00, first
02:00, second
ADELAIDE Adelaide +9.5 phone for some reason, you can Anchorage Sunday in
Sunday in March
change the summer time setting to November
SYDNEY Sydney +10
“STD” or “DST” manually. 02:00, first
LORD HOWE Lord Howe Los 02:00, second
+10.5 Sunday in
ISLAND Island Angeles Sunday in March
November
NOUMEA Noumea +11 02:00, first
WELLINGTON Wellington +12 02:00, second
Denver Sunday in
Sunday in March
CHATHAM Chatham November
+12.75
ISLANDS Islands 02:00, first
02:00, second
NUKU’ ALOFA Nuku’alofa +13 Chicago Sunday in
Sunday in March
KIRITIMATI Kiritimati +14 November
BAKER ISLAND Baker Island -12 02:00, first
02:00, second
New York Sunday in
PAGO PAGO Pago Pago -11 Sunday in March
November
HONOLULU Honolulu -10
02:00, first
MARQUESAS Marquesas 02:00, second
-9.5 Halifax Sunday in
ISLANDS Islands Sunday in March
November
ANCHORAGE Anchorage -9 02:00, first
02:00, second
LOS ANGELES Los Angeles -8 St. John’s Sunday in
Sunday in March
DENVER Denver -7 November
CHICAGO Chicago -6 00:00, third
Sunday in
NEW YORK New York -5 00:00, third
Rio de February or
HALIFAX Halifax -4 Sunday in
Janeiro 00:00, fourth
ST. JOHN’S St. John’s -3.5 October
Sunday in
RIO DE JANEIRO Rio de Janeiro -3 February
FERNANO DE Fernando de The information in the above table is current
-2 ●
35
Operation Guide 3452
Supported Phones Barometer : Stopwatch :
Measuring range: 260 to 1,100 hPa (or 7.65 Measuring unit: 1 second
For information about phones that can
to 32.45 inHg) Measuring range: 999 hours 59 minutes 59
connect with the watch, visit the CASIO
Display range: 260 to 1,100 hPa (or 7.65 to seconds (1,000 hours)
website.
32.45 inHg) Measurement accuracy: ±0.0006%
https://world.casio.com/os_mobile/wat/ Measuring unit: 1 hPa (or 0.05 inHg) Split times
Auto measurement interval: 2 hours
Countdown Timer :
Calibration
Setting unit: 1 minute
Specifications Barometric pressure graph
Measuring unit: 1 second
Barometric Pressure Change Indicator
Accuracy : Measuring range: 24 hours
Thermometer : Time up: 10-second beeper
±15 seconds a month (no adjustment by
Measuring range: -10.0°C to 60.0°C (or
signal information) World Time :
14.0°F to 140.0°F)
Basic Functions : Displays current time in UTC +39 cities (39
Display range: -10.0°C to 60.0°C (or 14.0°F
time zones) *, Auto Daylight Saving Time
Hour, minute, second, month, day, day of to 140.0°F)
(summer time) setting
the week, a.m./p.m. (P)/24-hour Measuring unit: 0.1°C (or 0.2°F)
timekeeping, full auto calendar (2000 to Calibration * Time zone data may change when the
2099) watch connects with a phone
Altimeter :
Mobile Link : Measuring range: -700 to 10,000 m (or Other :
Auto Time Adjustment -2,300 to 32,800 ft.) Power Saving, LED light, Selectable light
Auto Daylight Saving Time (summer time) Measuring unit: 1 m (or 5 ft.) duration, Auto Light, Charge level indicator,
switching Display Range: -10,000 to 10,000 m (or Button confirmation tone enable/disable,
Phone finder -32,800 to 32,800 ft.) Airplane Mode, 4 alarms (with snooze
Communication Specifications Measuring interval: 2 minutes/5 seconds setting, 10-second alarm beeper)
Bluetooth® Reference altitude setting
Batteries :
Frequency Band: 2400MHz to 2480MHz Altitude differential measurement: -3,000 to
Solar panel and one rechargeable battery
Maximum Transmission: 0 dBm (1 mW) +3,000m (or -9,840 to 9,840 ft.)
Range: Up to 2 meters (Depends on Battery Operating Time :
Sensor Accuracy :
environment.) Using GPS
Direction
Intermittent Receive: Approximately 33
GPS Navigation : Measurement accuracy: Within ±10°
hours maximum
Track log acquisition Assured accuracy temperature range:
Continual Receive: Approximately 20
Measurement intervals -10°C to 60°C (14°F to 140°F)
hours maximum
Intermittent (each minute, non-stop for Temperature
approximately 24 hours) Measurement accuracy: Within ±2°C * Other functions continue operating for
(±3.6°F) about 2 months after the GPS limits
Continual (every few seconds, non-stop
Assured accuracy temperature range: above.
for approximately four or five hours)
-10°C to 60°C (14°F to 140°F) Not Using GPS
Elapsed time measurement
Pressure Approximately 1.4 years
Log usage conditions
Display of straight-line distance to goal, Measurement accuracy: Within ±3 hPa Charger :
start, waypoints * (0.1 inHg) (Altitude measurement Operating temperature: 5°C to 35°C (41°F
Display of direction to goal, start, accuracy: Within ±75 m (246 ft.)) to 95°F)
waypoints * Assured accuracy temperature range: Power consumption: 5.0 V DC,
Goal specification (by recall from point -10°C to 40°C (14°F to 104°F) Approximately 0.9 W
memory)
Sunrise/Sunset :
Route Navigation *
Sunrise/sunset time display, Day select Specifications are subject to change without
Backtrack
notice.
Point memory (time, year/month/day, Tide/Moon * :
latitude/longitude, altitude, barometric Tide Level (Tide Graph)
pressure, temperature) Moon phase, Moon age
Point memory icon specification Day select
Track display switching (zoom out, zoom in) Time select (Tide Graph only)
* Waypoints are enabled only when settings * Requires configuration of app settings.
are configured with the app.
Digital Compass :
Measuring range: 0° to 359°
Compass calibration (3-point calibration,
magnetic declination angle)
60-second continuous measurement
Bearing memory
36
Operation Guide 3452
Mobile Link Precautions Copyrights and Registered Troubleshooting
Copyrights
● Legal Precautions
This watch complies with or has received The Bluetooth® word mark and logos are
Charging with the Charger
● ●
approval under the radio laws of various registered trademarks owned by the
countries and geographical areas. Using Bluetooth SIG, Inc. and any use of such
this watch in an area where it does not marks by CASIO Computer Co., Ltd. is Q1 The watch won’t charge with the
comply with or has not received approval under license. charger.
under applicable radio laws may be a ● iPhone is a registered trademark of
criminal offense. For details, visit the CASIO Apple Inc. in the United States and other Is the watch securely attached to the
Website. countries. charger?
https://world.casio.com/ce/BLE/
● iOS is a trademark or registered trademark Charging may fail if there is space
● Use of this watch inside of aircraft is of Cisco Systems, Inc. between the charger and watch.
restricted under the aviation laws of each
● GALAXY is a registered trademark of l Precautions When Charging
country. Be sure to follow the instructions of
Samsung Electronics Co., Ltd.
airline personnel.
● Android and Google PlayTM are trademarks Did you leave the watch attached to the
● Precautions when using Mobile Link or registered trademarks of Google LLC. charger after charging was complete?
● When using this watch in combination with ● Other company names and product names Charging stops automatically after the
a phone, keep the watch and phone close used herein are trademarks or registered watch becomes fully charged. If you want
to each other. A range of two meters is trademarks of their respective companies. to charge again, remove the watch from
recommended as a guideline, but the local and then re-attach it to the charger.
environment (walls, furniture, etc.), the
structure of a building, and other factors Is charging still impossible after checking
may require a much closer range. the above points?
● This watch can be affected by other devices
Check to make sure that the USB device
(electrical devices, audio-visual equipment,
or power source is functioning normally.
office equipment, etc.) In particular, it can
be affected by operation of a microwave
oven. The watch may not be able to Q2 Charging stops before it is complete.
communicate normally with a phone if a
Charging may stop if some temporary
microwave oven is operating nearby.
abnormality occurs. Unplug the USB cable
Conversely, this watch may cause noise in
from the charger and check for abnormalities.
radio reception and the video image of a TV.
If there is nothing wrong, try charging again.
● Bluetooth of this watch uses the same If the above does not eliminate the problem,
frequency band (2.4 GHz) as wireless LAN contact your original retailer or a CASIO
devices, and use of such devices in close service center.
proximity of this watch may result in radio
interference, slower communication
speeds and noise for the watch and the
wireless LAN device, or even
communication failure.
37
Operation Guide 3452
Signal Reception (GPS) Q4 The GPS signal receive operation I can’t pair the watch with a
always fails.
phone.
Q1 The watch cannot perform a GPS
Is the watch in a location that is appropriate
signal receive operation.
for signal reception? Q1 I’ve never been able to establish a
(pairing) connection between the
Is the watch’s battery charged? Check your surroundings and move the
watch and phone.
watch to a location where GPS signal
GPS signal reception is not possible while reception is better.
the battery indicator is or lower. Are you using a supported phone model?
l Appropriate Signal Reception Location
Charge the watch. Check if the phone model and its
l Charging the Watch Is the LCD of the watch pointed straight up operating system are supported by the
at the sky? watch.
Is the watch in the Timekeeping Mode? For information about supported phone
Minimize movement of the watch while the
models, visit the CASIO Website.
GPS signal reception is not possible receive operation is in progress.
unless the watch is in the Timekeeping When the watch is set up for auto receive, https://world.casio.com/os_mobile/wat/
Mode. Signal reception is also disabled in take care to avoid covering its LCD with
the Airplane Mode. Return to the the sleeve of your clothing. Did you install G-SHOCK Connected on
Timekeeping Mode. your phone?
38
Operation Guide 3452
I can’t reconnect the watch Q3 I can’t connect while the watch is in Phone-Watch Connection
the Airplane Mode.
and phone.
On the watch, exit the Airplane Mode. Next, Q1 I can’t establish a connection
on the watch, hold down (C) for about 2.5 between the phone and watch.
Q1 The watch will not re-connect with the seconds to enter the Communication Mode.
phone after they are disconnected.
l Mode Overview Have you tried turning your phone off and
Is G-SHOCK Connected running? then back on again?
The watch cannot re-connect with the On the phone, turn power off and then
phone unless G-SHOCK Connected is back on, and then tap the G-SHOCK
running on the phone. On the phone’s Connected icon. Next, on the watch, hold
Home Screen, tap the G-SHOCK down (C) for about 2.5 seconds to enter
Connected icon. Then on the watch, hold the Communication Mode.
down (C) for about 2.5 seconds to enter l Mode Overview
the Communication Mode. Q4 I changed the phone’s Bluetooth
from enabled to disabled, and now I
l Mode Overview
can’t connect anymore.
39
Operation Guide 3452
Changing to a Different Q3 The watch does not synchronize its Altitude Measurement
time setting with a phone even
Phone Model
though I follow the steps under
Triggering Immediate Time Q1 Readings produce different results at
the same location.
Q1 Connecting the current watch to Adjustment.
another phone. Watch readings are different from
The watch will not start time adjustment while altitude information available from
Pair the watch with the phone. a timer countdown operation is in progress. other sources.
l After Purchasing Another Phone Wait until the timer countdown operation is Correct altitude readings are not
complete and then perform the operation possible.
again.
Relative altitude is calculated based on
Auto Time Adjustment by changes in barometric pressure measured by
Q4 Time is not displayed correctly.
Bluetooth Connection (Time the watch’s pressure sensor. This means that
The phone’s time setting may be incorrect barometric pressure changes can cause
Adjustment)
because it is unable to connect with its readings taken at the same location to be
network due to being out of range, etc. If this different. Also note that the value displayed by
Q1 When does the watch adjust is time? happens, connect the phone to its network the watch may be different from the actual
and then adjust the time setting. elevation and/or sea level elevation indicated
The watch will connect with the phone and
for the area where you are located. When
perform auto time adjustment at around 12:30
using the watch’s altimeter while mountain
a.m., 6:30 a.m., 12:30 p.m. and 6:30 p.m. The
climbing, it is recommended that you regularly
connection is automatically terminated after Navigation
calibrate its readings in accordance with local
auto time adjustment is complete. Also, GPS
altitude (elevation) indications.
signal auto receive will be performed if there
Q1 The watch won’t enter the GPS l Calibrating Altitude Readings
has been no auto time adjustment based on
Navigation Mode.
connection between the watch and phone for
more than one day. Q2 [-----] appears on the display
Is the watch being charged with the following altitude differential
charger? measurement.
Q2 Auto time adjustment is performed,
but the time setting is not correct. The GPS Navigation Mode cannot be [-----] appears when the altitude differential is
used while the watch is being charged outside the allowable measuring range
Is auto time adjustment not being with the charger. Remove the watch from (±3,000 m). If [ERROR] appears on the
performed according to its normal the charger. display, there may be a problem with the
schedule? sensor.
Is the battery charge level sufficient? l Setting a Reference Altitude and Taking
Note that auto time adjustment is not Relative Altitude Readings
The GPS function can be used only when
performed for 24 hours after the time
setting is adjusted manually on the watch. the battery indicator shows or higher.
Auto time adjustment will resume after 24 If the battery charge level is too low,
Q3 [ERROR] appears during
measurement.
hours. charge the watch.
l Charging the Watch There may be a problem with the sensor. Try
Is a timer countdown operation in taking another measurement. If [ERROR]
progress? keeps appearing after multiple measurement
attempts, contact a CASIO service center.
Auto time adjustment will not start at the
scheduled times if a timer countdown
operation is in progress. Stop the timer
countdown operation.
l Using the Timer
40
Operation Guide 3452
Digital Compass Barometric Pressure
Measurement
Q1 The symbol is shown on the
display. Q1 [ERROR] appears during
measurement.
Abnormal magnetism has been detected.
Move away from any potential source of There may be a problem with the sensor. Try
strong magnetism and try taking a reading taking another measurement. If [ERROR]
again. keeps appearing after multiple measurement
l Digital Compass Reading Precautions attempts, contact a CASIO service center.
● If appears again, it could mean that the
watch body has become magnetized. Move
away from any potential source of strong Temperature Measurement
magnetism, perform direction calibration,
and then try taking a reading again.
Q1 [ERROR] appears during
l Calibrating Compass Readings measurement.
41