Professional Documents
Culture Documents
Artis Zee/Zeego (Until VC14) / Axiom Artis 3D Calibration Test Necessary Tools For Performing These Tests
Artis Zee/Zeego (Until VC14) / Axiom Artis 3D Calibration Test Necessary Tools For Performing These Tests
3D Calibration Test
General Prerequisites
Be sure that the Artis zee / zeego is adjusted according to the appropriate IQAP specifications.
Most important parameters are
n Dose (Check with "Indirect dose" in the Artis IQAP)
n Iris diaphragm (check with "Dynamic test" in the Artis IQAP), (for I.I. systems only)
n Resolution (check with "CTF" in the Artis IQAP), (for I.I. systems only)
n FD calibration
n DEXI adjustment
Acquisition programs
The acquisiton programs/3D protocols for the phantom acquisitions are described in the respective subsections
in the following chapters.
Fast wire-test
Acquisition program
1/10
3D Calibration Test – Artis Zee/Zeego (until VC14) / Axiom Artis
Depending on acquisition system and installed options, one of the following acquisition programs must be used
for the image quality test.
Depending on the type of stand, the geometry tests have to be repeated for all “system positions”.
n Head end/Table 0˚
n Left side
n Head end
n Right side
n Left side/Table 0˚
n Head end/Table 0˚
n Right side/Table 0˚
Zoom format
Depending on the installed detector (image intensifier or flat detector), one of the following zoom formats
must be set.
Acquisition procedure
2/10
3D Calibration Test – Artis Zee/Zeego (until VC14) / Axiom Artis
Place some long, thin wires on the patient table parallel to the patient axis. In this example, we have used two
n
metal wires with a diameter of about 1.5 mm and stainless steel GDC delivery wire (attached to a GDC coil).
Do not use a catheter, it should be avery thin metal wire!
Fig. 1:
n Adjust the table height and the table position so that the wires are in the isocenter.
n Acquire a 3D acquisition scene with the settings mentioned above.
n Transfer data to the syngo X Workplace / LEONARDO Workstation using Image > Send to 3D in the
main menu of the PostProc task card on the Artis Imaging System (with AXIS, the transfer is started
automatically!).
- Select Patient > InSpace Reconstruction
3/10
3D Calibration Test – Artis Zee/Zeego (until VC14) / Axiom Artis
Fig. 2:
4/10
3D Calibration Test – Artis Zee/Zeego (until VC14) / Axiom Artis
Evaluation in InSpace
n Load the data set using the Patient Browser into an application that is able to process MPR images, e.g.
into the InSpace or 3D task card. (As an example, the procedure is explained for InSpace, the procedure
for 3D is similar.)
n The wires should be well visible in Volume Rendering. Their profile shall be well defined, with sharp
edges
Fig. 3:
5/10
3D Calibration Test – Artis Zee/Zeego (until VC14) / Axiom Artis
Fig. 4:
n Move blue reference line in top windows head side. The wire profiles shall be round
6/10
3D Calibration Test – Artis Zee/Zeego (until VC14) / Axiom Artis
Fig. 5:
n Move blue reference line in top windows feet side. The wire profiles shall be round.
7/10
3D Calibration Test – Artis Zee/Zeego (until VC14) / Axiom Artis
Fig. 6:
For I.I. systems: Here, the dark rings (two semicircles) are unavoidable and are caused by the edges of the
semitransparent collimators.
8/10
3D Calibration Test – Artis Zee/Zeego (until VC14) / Axiom Artis
If there is a problem, the images appear as follows:
Fig. 7:
9/10
3D Calibration Test – Artis Zee/Zeego (until VC14) / Axiom Artis
The MPR view looks like
Fig. 8:
In this case, either the data set were not properly acquired (table tilt, table cradle or table rotation not in 0
position, C-Arm not properly pivoted into the 0 position, C-Arm not properly moved to the 3D start position
before acquisition), or the calibration of the system is no longer appropriate.
10/10
3D Calibration Test – Artis Zee/Zeego (until VC14) / Axiom Artis