Professional Documents
Culture Documents
Desarmado Nose Cone 769
Desarmado Nose Cone 769
OffHighway Truck BBB00001UP (MACHINE) POWERED BY 3408E Engine(SEBP3399 65) Código SMCS
Pantalla anterior
Bienvenido: cr461prodeco
Producto: TRUCK
Modelo: 769D TRUCK BBB
Configuración: 769D OffHighway Truck BBB00001UP (MACHINE)
POWERED BY 3408E Engine
Desarmado y Armado
69D and 769D OffHighway Truck and 771D Quarry Truck Power Train
Número de medio SENR155103 Fecha de publicación 01/08/2006 Fecha de actualización 24/08/2006
i00962103
Rear Axle Housing and Differential Remove
SMCS 3258011; 3260011
Removal Procedure
Table 1
Required Tools
Start By:
A. Remove the body and canopy. Refer to Disassembly and Assembly, SENR1561, "Body and
Canopy Remove".
B. Remove the rear suspension (cylinders). Refer to Disassembly and Assembly, SENR1561,
"Rear Suspension (Cylinder) Remove".
C. Remove the lateral control rod (rear axle housing). Refer to Disassembly and Assembly,
"Lateral Control Rod (Rear Axle Housing) Remove and Install".
D. Remove the rear drive shaft. Refer to Disassembly and Assembly, "Drive Shaft (Rear)
Remove and Install".
NOTICE
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/smcssearch/sis_smcsthirdframeset.jsp&calledpage=/sisweb… 1/7
26/5/2015 769D OffHighway Truck BBB00001UP (MACHINE) POWERED BY 3408E Engine(SEBP3399 65) Código SMCS
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the rear axle housing. Refer to Operation and Maintenance Manual, SEBU7092,
"Differential and Final Drive Oil Change".
2. Drain the hydraulic tank (hoist and brake). Refer to Operation and Maintenance Manual,
SEBU7092, "Hoist and Brake Tank Oil Change".
3. Install caps and plugs on all openings in order to prevent dirt or debris from entering the system.
Cleanliness is an important factor. Before the removal procedure, the exterior of the component
should be thoroughly cleaned. This will prevent dirt from entering the internal mechanism.
Illustration 1 g00578503
4. Position a suitable container below hose assembly (1) and (2) in order to contain hydraulic oil
for storage or disposal. Disconnect hose assemblies (1) and (2) .
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/smcssearch/sis_smcsthirdframeset.jsp&calledpage=/sisweb… 2/7
26/5/2015 769D OffHighway Truck BBB00001UP (MACHINE) POWERED BY 3408E Engine(SEBP3399 65) Código SMCS
Illustration 2 g00578506
5. Position a suitable container below hose assembly (3) and (4) in order to contain hydraulic oil
for storage or disposal. Disconnect hose assemblies (3) and (4) .
Illustration 3 g00578510
6. Remove lockwire (6). Disconnect wire harness (5) from the speed sensor. Remove all the nuts,
the bolts, and the clips that hold wire harness (5) to the rear axle housing. Position wire harness
(5) out of the way.
7. Repeat Step 6 for the remaining speed sensor. The speed sensor is located on the other end of
the rear axle housing.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/smcssearch/sis_smcsthirdframeset.jsp&calledpage=/sisweb… 3/7
26/5/2015 769D OffHighway Truck BBB00001UP (MACHINE) POWERED BY 3408E Engine(SEBP3399 65) Código SMCS
Illustration 4 g00578641
8. Loosen the four top bolts (7) on bolster cap (8) .
Illustration 5 g00578663
9. Use Tooling (A) in order to raise the frame assembly above the rear axle housing.
Illustration 6 g00578699
10. Attach Tool (B) to the rear axle housing, as shown. Position Tool (C) under the rear axle
housing, as shown. Apply pressure to the front of the rear axle housing with Tool (C) .
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/smcssearch/sis_smcsthirdframeset.jsp&calledpage=/sisweb… 4/7
26/5/2015 769D OffHighway Truck BBB00001UP (MACHINE) POWERED BY 3408E Engine(SEBP3399 65) Código SMCS
Illustration 7 g00578703
11. Remove eight bolts (7) and the hard washers from bolster cap (8) .
Illustration 8 g00578710
NOTICE
To avoid damage to the braking system, do not exceed 3150 kPa (460
psi) when applying pressure to release the parking brake.
12. Fasten Tooling (D) (not shown) to the rear service and parking brake in order to release the
parking brake.
13. Attach two suitable lifting slings to rear axle housing (9). Attach the two lifting slings to a
suitable lift truck. Pull rear axle housing (9) from the frame assembly.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/smcssearch/sis_smcsthirdframeset.jsp&calledpage=/sisweb… 5/7
26/5/2015 769D OffHighway Truck BBB00001UP (MACHINE) POWERED BY 3408E Engine(SEBP3399 65) Código SMCS
Illustration 9 g00578999
Illustration 10 g00579006
14. If necessary, remove stake nut (10). Remove kingbolt (11) and bolster cap (12) from the support
assembly. Illustrations 9 and 10 show the 775D Off Highway Truck. The procedure for the
771D Off Highway Truck is identical. The weight of kingbolt (11) is 39 kg (86 lb). The weight
of bolster cap is 12 kg (26 lb).
Illustration 11 g00578993
15. Remove two bolts (13) and the washers. Remove ball socket (14) from the frame assembly. The
weight of ball socket is 29 kg (64 lb).
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/smcssearch/sis_smcsthirdframeset.jsp&calledpage=/sisweb… 6/7
26/5/2015 769D OffHighway Truck BBB00001UP (MACHINE) POWERED BY 3408E Engine(SEBP3399 65) Código SMCS
Copyright 1993 2015 Caterpillar Inc.
Todos los derechos reservados.
Tue May 26 2015 11:24:42 GMT0500 (Hora est. Pacífico, Sudamérica)
cr461prodeco
Red privada para licenciados del SIS.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/smcssearch/sis_smcsthirdframeset.jsp&calledpage=/sisweb… 7/7