Professional Documents
Culture Documents
NSC Plate
NSC Plate
NSC Plate
STEEL PLATES
Cat. No. AC314 2009.9 PDF
© 2005, 2009 NIPPON STEEL CORPORATION All Rights Reserved. Printed in Japan
Features
Limestone
Iron ore Continuous reheating
furnace
Continuous
Sintering plant casting
Coal
Torpedo car Slab conditioning/
Coking plant Dimensional inspection Roughing Finishing Hot leveling
Basic oxygen mill mill machine
Blast furnace furnace
Controlled cooling
Secondary
refining Batch reheating furnace
CLC® Steel Plate 1. Outline of CLC (2)Application Advantages of CLC 490 N/mm2 High- 3. Example Applications of CLC 490
CLC is a new plate manufacturing process based on the strength Steel Plates N/mm2 High-strength Steel Plates
Nippon Steel has developed an innovative plate CLC 490 N/mm2 high-strength steel plates offer an out
combined use of controlled rolling and controlled cooling. (1)Shipbuilding and offshore structures
manufacturing technology known as CLC (Continuous standing improvement in weldability through a signify cant
When producing 490 N/mm2 high-strength steel CLC 490 N/mm2 high-strength steel plates have obtained
On Line Control Process). CLC technology is applied plates by means of CLC, the carbon equivalent can reduction of the carbon equivalent. This produces the approvals from the following classification societies.
in the manufacture of high-strength steel plates with greatly be reduced because the desired strength is
fol-lowing application advantages and high user ratings.
● Lower preheating temperatures during welding than are Standards of classification societies that approved CLC plates (examples)
strength ratings of 490 N/mm2 or more and such secured through controlled cooling. acceptable for conventional high-strength steel plates, YP315N/mm2 YP355N/mm2 YP390N/mm2
highly improved properties as low-temperature An outline of the equipment used in CLC is shown in A- D- E- A- D- E- A- D- E-
made possible by the reduction of carbon equivalent.
toughness and weld ability. These high-strength steel Fig. 1. ● Lower maximum hardness of welded joints than in
Classification Grade Grade Grade Grade Grade Grade Grade Grade Grade
plates are used in a wide range of fields: shipbuilding, con-ventional high-strength steel plates.
NK ● ● ● ● ● ● ● ● ●
offshore structures, bridges, building construction, ABS ● ● ● ● ● ● ● ● ●
● Improved toughness of welded joints Extreme reduction
industrial machinery, line pipe and storage tanks. DNV ● ● ● ● ● ● ● ● ●
in material quality changes caused by line heating.
● Extreme reduction in material quality changes caused by LR ● ● ● ● ● ● ● ● ●
line heating. BV ● ● ● ● ● ● ● ● ●
Fig.1 CLC equipment layout
●Application
examples
Controlled rolling Controlled cooling Fig.2 Relation between carbon equivalent and strength of Shipbuilding: Tankers, cargo vessels, container ships,
steel plates produced by conventional and CLC methods refrigerator vessels, etc.
(plate thickness: 20~30 mm) Offshore structures: Jack-up rigs, semi-submersible rigs,
crane barge, etc.
Tensile strength(N/mm2)
(2)BT-HT325, 355 and 400 for building structures
700
CLC (water cooling-type TMCP)
(3)Industrial machinery, line pipe, storage tanks and
other widely ranging general-purpose applications
600
Hot leveling 4. High-toughness, High-strength Steel
Reheating furnace Scale breaker Roughing mill Finishing mill machine 500 Plates for Low-temperature Applications
In response to user requests, CLC technology is increasingly
Non-water cooling-type
TMCP (air cooling) applied in the manufacture of high-toughness, high-strength
400
As-rolled (air cooling) steel plates for low-temperature applications (offshore struc-
※TMCP (Thermo-Mechanical Control Process) is tures, jackets, offshore facilities, etc.).
a generic term for the controlled rolling process 0.20 0.30 0.40 0.50
for plate manufacture, or the process combining 2. Features of CLC 490 N/mm2 High- Carbon equivalent(%)
5. Example Applications in Standards
controlled rolling with controlled cooling. strength Steel Plates (1)Adoption in ASTM: A841 (Steel Plates for Pressure Ves-
The CLC process falls under the latter category. sels), A844 (9% Ni Steel Plates)
(1)Extra-low Carbon Equivalent
Toughness is improved by making the most of extra low (2)Adoption in JIS: G 3106 SM Grade, G 3114 SMA Grade,
carbon equivalent and CLC. G 3136 SN Grade
STEEL PLATES (AC314)
Copyright © 2005, 2009 NIPPON STEEL CORPORATION. All rights reserved.
Excerpts of Nippon Steel Standards
t≦50
WEL-TEN690 0.60 0.30 ≦0.50 t≦16 17 No.5
≦0.16 ≦0.35 ≦0.030 ≦0.025 ≦0.50 ≦0.60 ≦0.40 ≦0.10 ー ≦0.005 ー ー t<32 1.5 t 12<t≦32 -15 47≦
(6∼75mm) ∼1.20 ∼1.00 t≦50 t≦50
t≦75
≦0.55 620≦ 690∼830 4)
16<t 25 No.5
50<t 50<t
WEL-TEN690C 0.60 Nb+V 600≦ 670∼810
≦0.16 ≦0.35 ≦0.030 ≦0.025 ≦0.50 ー ≦0.80 ≦0.40 ≦0.005 ー ≦0.50 ー 32≦t 2.0 t 32<t≦75 -25 47≦
(6∼50mm) ∼1.20 ≦0.15
20<t 17 No.4
1) Carbon equivalent, Ceq, and weld crack sensitivity, PCM, are 2) Ceq is as follows. 3) When specially ordered, the yield point can be set at
calculated for added elements using the following equation. 490 N/mm2 or more.
Plate thickness (mm)
Ceq=C + Si/24 + Mn/6 + Ni/40 + Cr/5 + Mo/4 + V/14% Brand name 4) When specially ordered, the tensile strength of WEL-TEN
t≦50 50<t≦75 75<t≦100 100<t≦150 t<150 690 and 690C with thickness of 50 mm or under can be
PCM= C + Si/30 + Mn/20 + Cu/20 + Ni/60 + Cr/20 + Mo/15 + V/10 + 5B % WEL-TEN590 ≦0.44 ≦0.46 ≦0.49 ≦0.52 ≦0.56 set at 710 N/mm2 or more.
WEL-TEN610 ≦0.45 ≦0.47 ≦0.50 ≦0.53 ≦0.57 5) In the bending test, cracks shall not occur in the outside
of test piece.
The bending test can be eliminated unless otherwise
specified.
WEL-TEN AR285E 3)In the bending test, cracks shall not occur in the
285≦
(6∼50mm) outside of test piece.
≦0.22 The bending test can be eliminated unless otherwise
WEL-TEN AR320E
≦0.025 ≦0.015 ー ≦0.50 ー ≦0.005 321≦ specified.
(6∼50mm)
WEL-TEN AR360E
361≦
(6∼50mm) 0.15∼0.55 ≦1.60 ー ー
WEL-TEN AR400E
≦0.25 401≦
(6∼50mm)
t≦20 t≦20
WEL-TEN AR500E ー ー
≦0.35 ≦0.015 ≦0.010 ≦1.00 ≦0.005 477≦
(6∼50mm) 20<t 20<t
≦0.30 ≦0.15
WEL-HARD 400
≦0.22 0.15∼0.55 ≦0.025 ≦0.015 ー ー ≦0.50 ー ー 361∼440
(6∼50mm)
≦1.60 ≦0.005 1)Hardness test shall be carried out in
WEL-HARD 500 accordance with JIS Z 2243
≦0.35 0.15∼0.35 ≦0.015 ≦0.010 ー ー ≦1.00 ≦0.15 ー 451∼550
(6∼50mm) (Method of Brinell Hardness Test).
A t≦16 365≦ ー ー
No.1A t≦16 15
0.50 Cr ≦0.08 16<t≦40 355≦
NAW-TEN12-490 B 6≦t≦100 ≦0.18 ≦0.55 ≦1.60 ≦0.035 ≦0.035 490∼610 No.1A 16<t 19 0 27≦
∼1.00 Ni 0.70∼1.70 40<t≦75 335≦
No.4 40<t 21
C 75<t≦100 325≦ 0 47≦
t≦16 460≦
No.5 t≦16 19
0.15 16<t≦40 450≦
NEW-TEN12-570 6≦t≦100 ≦1.40 570∼720 No.5 16<t 26 -5 47≦
∼0.65 40<t≦75 430≦
No.4 40<t 20
75<t≦100 420≦
A t≦16 245≦ No.1A t≦16 ー ー
17
NAW-TEN30-400 B 6≦t≦100 ≦1.25 16<t≦40 235≦ 400∼540 No.1A 16<t 21 0 27≦
40<t≦100 215≦ No.4 40<t 23
C 0 47≦
A t≦16 365≦ ー ー
No.1A t≦16 15
0.15 0.30 Cr ≦0.08 16<t≦40 355≦
NAW-TEN30-490 B 6≦t≦100 ≦0.18 ≦0.035 ≦0.035 490∼610 No.1A 16<t 19 0 27≦
∼0.65 ∼0.50 Ni 2.50∼3.50 40<t≦75 335≦
No.4 40<t 21
C 75<t≦100 325≦ 0 47≦
≦1.40
t≦16 460≦
No.5 t≦16 19
16<t≦40 450≦
NEW-TEN30-570 6≦t≦100 570∼720 No.5 16<t 26 -5 47≦
40<t≦75 430≦
No.4 40<t 20
75<t≦100 420≦
Steel for Elasto-plastic Hysteretic-type Dampers for Building Structures: BT-LYP®100 and 225
These are low yield-point steel and extra-low yield- Chemical composition(%) Mechanical properties Standard available sizes
point steel used for elasto-plastic hysteretic-type (For the sizes surpassing the following, advance
Impact test V notch
vibration dampers that are used to absorb seismic consultation is requested.)
Brand name 0.2% proof Tensile
energy. Yield point Yield ratio Elongation Thickness 6∼50mm
C Si Mn P S N Ceq stress strength Temperature A prorked
energy Length 3,000∼8,000mm
Features:
(N/mm2) (N/mm2) (N/mm2) (%) (%) (°C) (J) Width 1,000∼2,500mm
■ Yield point is low (100 N/mm2 level for BT-LYP 100 and 225
N/mm2 level for BT-LYP 225) and the range of yield point However, the width of BT-LYP100 is limited as in
(yield strength) deviation is narrowly controlled. the following so as to prevent the deformation.
■ General elongation properties of 50% or more are BT-LYP100 ≦0.01 ≦0.03 ≦0.20 ≦0.025 ≦0.015 ≦0.006 ≦0.36 ー 80∼120 200∼300 ≦60 50≦ 0 27≦
Thickness 6∼8mm Thickness Width 2,000mm
guaranteed for BT-LYP 100 and 40% or more for BT-LYP
Length 9∼20mm Thickness Width 2,300mm
225, thereby offering the large deformation capacity
required of vibration dampers. Width 21∼50mm Thickness Width 2,500mm
■ Small-lot orders are available. Advance consultation is
BT-LYP225 ≦0.10 ≦0.05 ≦0.50 ≦0.025 ≦0.015 ≦0.006 ≦0.36 205∼245 ー 300∼400 ≦80 40≦ 0 27≦ Remarks:
requested regarding use.
(1) The tensile test piece shall be the JIS Z 2201 No. 5
test piece (gauge length: 50 mm).
(2) The procedure of mechanical test shall conform to the
provision of JIS G 3136.
(3) Allowable thickness tolerance shall conform to the
provision of JIS G 3136.