Professional Documents
Culture Documents
HP LaserJet M201-M202-M225-M226 Service Manual
HP LaserJet M201-M202-M225-M226 Service Manual
M201n M201dw
M202n M202dw
M225dn M225dw
M225rdn M226dw
M226dn
www.hp.com/support/ljM201
www.hp.com/support/ljM202
www.hp.com/support/ljMFPM225
www.hp.com/support/ljMFPM226
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
HP LaserJet Pro MFP M225/M226 series and
HP LaserJet Pro M201/M202 Printer series
Replace and Repair Manual
Edition 1, 10/2014
CAUTION: Cautions indicate procedures that you should follow to avoid losing data or damaging the
product.
WARNING! Warnings alert you to specific procedures that you should follow to avoid personal injury,
catastrophic loss of data, or extensive damage to the product.
ENWW iii
ENWW v
vi ENWW
ENWW vii
3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ......................................................................... 139
Order parts by authorized service providers .................................................................................................... 140
Order replacement parts ................................................................................................................ 140
Related documentation .................................................................................................................. 140
Supplies part numbers .................................................................................................................... 140
Customer self repair parts .............................................................................................................. 141
Service parts .................................................................................................................................... 141
Whole-unit replacement part numbers .......................................................................................... 141
How to use the parts lists and diagrams .......................................................................................................... 143
Covers ................................................................................................................................................................ 144
Internal assemblies ........................................................................................................................................... 146
Internal assemblies (1 of 3) ............................................................................................................ 146
Internal assemblies (2 of 3) ............................................................................................................ 148
Internal assemblies (3 of 3) ............................................................................................................ 150
Scanner and document feeder (ADF) ................................................................................................................ 152
Scanner and document feeder (ADF) main assemblies ................................................................. 152
Document feeder internal components ......................................................................................... 154
Scanner assembly internal components .......................................................................................................... 156
Scanner assembly internal components (1 of 2) ........................................................................... 156
Scanner assembly internal components (2 of 2) ........................................................................... 158
Alphabetical parts list ....................................................................................................................................... 160
Numerical parts list ........................................................................................................................................... 163
viii ENWW
ENWW ix
ENWW xi
ENWW xiii
xiv ENWW
ENWW xv
xvi ENWW
ENWW xvii
● Service strategy
ENWW 1
Never operate or service the product with the protective cover removed from the laser/scanner assembly.
The reflected beam, although invisible, can damage your eyes.
The sheet-metal parts might have sharp edges. Be careful when handling sheet-metal parts.
CAUTION: Do not bend or fold the flat flexible cables (FFCs) during removal or installation. Also, do not
straighten pre-folds in the FFCs. You must fully seat all FFCs in their connectors. Failure to fully seat an FFC
into a connector can cause a short circuit in a PCA.
NOTE: To install a self-tapping screw, first turn it counterclockwise to align it with the existing thread
pattern, and then carefully turn it clockwise to tighten. Do not overtighten. If a self-tapping screw-hole
becomes stripped, repair the screw-hole or replace the affected assembly.
TIP: For clarity, some photos in this chapter show components removed that would not be removed to
service the product. If necessary, remove the components listed at the beginning of a procedure before
proceeding to service the product.
Electrostatic discharge
CAUTION: Some parts are sensitive to electrostatic discharge (ESD). Look for the ESD reminder when
removing product parts. Always perform service work at an ESD-protected workstation or mat, or use an ESD
strap. If an ESD workstation, mat, or strap is not available, ground yourself by touching the sheet-metal
chassis before touching an ESD-sensitive part.
Protect the ESD-sensitive parts by placing them in ESD pouches when they are out of the product.
Required tools
● #2 Phillips screwdriver with a magnetic tip and a 152-mm (6-inch) shaft length
● Needle-nose pliers
● Penlight (optional)
CAUTION: Always use a Phillips screwdriver (callout 1). Do not use a pozidrive screwdriver (callout 2) or any
motorized screwdriver. These can damage screws or screw threads.
NOTE: The screw illustrations in the following table are for reference only. Screws might vary in size and
appearance from those shown in this table.
M4X6 XB2-7400-605CN
M4X12 XA9-1422-000CN
M4X15 XB4-7401-609CN
M3X6 XB6-7300-605CN
M3X8 XA9-1671-000CN
12 mm
● Place the product on an ESD workstation or mat, or use an ESD strap (if one is available). If an ESD
workstation, mat, or strap is not available, ground yourself by touching the sheet-metal chassis before
touching an ESD-sensitive part.
Post-service test
Perform the following test to verify that the repair or replacement was successful.
Print-quality test
1. Verify that you have completed the necessary reassembly steps.
3. Attach the power cord and interface cable or interface cables, and then turn on the product.
5. Print a configuration page, and then verify that the expected printing sounds occur.
6. Print a demo page, and then verify that the print quality is as expected.
7. Send a print job from the host computer, and then verify that the output meets expectations.
Separation pad
Transfer roller
Left cover
Formatter PCA
Front cover
Control panel
Right cover
Cartridge door
Laser/scanner asssembly
Main motor
Top cover
Pickup assembly
Fuser
Pickup solenoid
Engine controller PCA
Duplex-reverse solenoid (duplex models)
Main fan (duplex models)
Duplex-connector PCA (duplex models)
Figure 1-3 Parts removal order: ADF and scanner (MFP models)
Automatic document feeder assembly
ADF core
Scanner assembly
Scanner bezel
Scan-drive system
DC servo motor
Scan bar
Scanner base
SSA hinge
1. Place the product rear-side down to access the separation pad assembly.
CAUTION: Dirt and debris can scratch the product covers. Place the product on a cloth or other clean
surface.
2. Remove two screws (callout 1) and then remove the separation pad assembly (callout 2).
Item Description
1 Cartridge door
2 Right cover
5 Left cover
10 Dust cover
Dust cover
Release two shafts (callout 1) and remove the dust cover (callout 2).
2. Pull the input tray assembly (callout 1) towards the front side of the printer and remove it.
1 1
● Left cover. See Left cover, duplex product on page 12 or Left cover, simplex product on page 13.
1
2
3. Remove one screw (callout 1), then release five tabs (callout 2) and remove the front cover assembly
(callout 3).
2. Release five tabs (callout 1) and remove the right cover (callout 2).
Release two shafts (callout 1) and remove the duplex door ass’y (callout 2).
● Top cover cap (duplex models). See Top cover cap, duplex product on page 14.
1. Release two tabs (callout 1), and then remove the duplex reverse guide (callout 2).
1. Release three tabs at the top of the cover (callout 1), and then release three tabs at the bottom of the
cover (callout 2).
● Rear cover, simplex product. See Rear cover, simplex product on page 22.
4. Release one tab (callout 1) and remove the cartridge shaft cover (callout 2).
● Rear cover, simplex product. See Rear cover, simplex product on page 22.
4. Release one tab (callout 1) and remove the cartridge shaft cover (callout 2).
● Top cover cap, duplex product. See Top cover cap, duplex product on page 14.
4. Remove the cartridge door (callout 1) and the top cover (callout 2) together.
● Output bin tray extension. See Output tray assembly on page 11.
● Left cover. See Left cover, duplex product on page 12 or Left cover, duplex product on page 12.
● Right cover. See Right cover, duplex product on page 16 or Right cover, simplex product on page 18.
● Cartridge door. See Cartridge door, duplex product on page 29 or Cartridge door, simplex product
on page 23.
CAUTION: The upper-cartridge door arms (callout 2) can become easily be dislodged from the lower
arms. Do not lose the upper-cartridge door arms while servicing the product.
Item Description
1 Top cover
2 Cartridge door
3 Right cover
5 Left cover
Item Description
8 Dust cover
Dust cover
Release two shafts (callout 1) and remove the dust cover (callout 2).
1 2
2. Pull the input tray assembly (callout 1) towards the front side of the printer and remove it.
Left cover
1. Open the duplex door assembly.
2. Remove three screws (callout 1), and then remove one screw (callout 2) to release the ground strap
(callout 3).
Right cover
2. Carefully remove the two FFCs from the guides (callout 1).
4. Lift the scanner assembly up (arrow 1) and away from the hinges (arrow 2).
Duplex door
▲ Release two shafts (callout 1) and remove the duplex door ass’y (callout 2).
2
1
1. Release two tabs (callout 1), and then remove the duplex reverse guide (callout 2).
Cartridge door
1 1
2. Release two link arms on the left side (callout 1) and two link arms on the right side (callout 2).
1 2
● Output bin tray extension. See Output tray assembly on page 37.
CAUTION: The upper-cartridge door arms (callout 2) can become easily be dislodged from the lower
arms. Do not lose the upper-cartridge door arms while servicing the product.
2. Release two tabs (callout 1), and then remove the transfer roller (callout 2).
2 1
Internal assemblies
Formatter PCA
1. Remove the left cover. See Left cover, duplex product on page 12 or Left cover, simplex product
on page 13 or Left cover on page 37.
3. Remove four screws (callout 1), and then remove the formatter PCA (callout 2).
● Input tray assembly. See Input tray assembly on page 11 or Input tray assembly on page 36.
● Output tray assembly. See Output tray assembly on page 11 or Output tray assembly on page 37.
● Left cover. See Left cover, duplex product on page 12 or Left cover, simplex product on page 13 or Left
cover on page 37.
● Front cover assembly. See Front cover assembly on page 15 or Front cover assembly on page 38.
● Right cover. See Right cover, duplex product on page 16 or Right cover, simplex product on page 18 or
Right cover on page 40.
● Rear cover (simplex product) or duplex door (duplex product). See Rear cover, simplex product
on page 22 or Duplex door, duplex product on page 20 or Duplex door on page 46.
● Duplex frame (duplex products only). See Duplex frame, duplex product on page 21 or Duplex frame
on page 47.
● Cartridge door. See Cartridge door, duplex product on page 29 or Cartridge door, simplex product
on page 23 or Cartridge door on page 48.
● Top cover. See Top cover on page 33 or Top cover on page 52.
1. Duplex models only: Release two tabs (callout 1), and then remove the duplex reverse guide (callout 2).
2
1
3. Remove one FFC (callout 1), remove four screws (callout 2), and then remove the fax PCA (callout 3).
5. Disconnect one connector (callout 1), and then release the wire harness (callout 2) from the guide
(callout 3).
7. Disconnect one tab (callout 1), and then remove the guide (callout 2).
9. On the right side of the product, remove two screws (callout 1) and the sheet-metal brace (callout 2),
and then remove one bushing (callout 3).
2. Disconnect one connector (callout 1), then release the cables (callout 2) from the cable guide (callout 3).
3 1
5. Examine the assembly and locate the components in Table 1-4 Fuser film assembly components
on page 65.
2 1 3
Item Description
The shape of the pressure release lever is different between the products.
Figure 1-94 Pressure release levers, LaserJet Pro MFP M225 and M226 series
Laser/scanner assembly
● Input tray assembly. See Input tray assembly on page 11 or Input tray assembly on page 36.
● Output tray assembly. See Output tray assembly on page 11 or Output tray assembly on page 37.
● Left cover. See Left cover, duplex product on page 12 or Left cover, simplex product on page 13 or Left
cover on page 37.
● Front cover assembly. See Front cover assembly on page 15 or Front cover assembly on page 38.
● Right cover. See Right cover, duplex product on page 16 or Right cover, simplex product on page 18 or
Right cover on page 40.
1. Release one tab (callout 1), and then remove the holder (callout 2).
2. Remove four screws (callout 1), and then remove the scanner cover (callout 2) and the sheet-metal
plate (callout 3) together.
CAUTION: The scanner cover (callout 2) and sheet-metal plate (callout 3) can be easily separated. Do
not lose the plate while servicing the product.
TIP: When the cover is reinstalled, make sure that the black screws (callout 4) are installed in the
correct screw holes.
1
2 3
● Input tray assembly. See Input tray assembly on page 11 or Input tray assembly on page 36.
● Output tray assembly. See Output tray assembly on page 11 or Output tray assembly on page 37.
● Left cover. See Left cover, duplex product on page 12 or Left cover, simplex product on page 13 or Left
cover on page 37.
● Front cover assembly. See Front cover assembly on page 15 or Front cover assembly on page 38.
● Right cover. See Right cover, duplex product on page 16 or Right cover, simplex product on page 18 or
Right cover on page 40.
● Rear cover (simplex product) or duplex door (duplex product). See Rear cover, simplex product
on page 22 or Duplex door, duplex product on page 20 or Duplex door on page 46.
● Duplex frame (duplex products only). See Duplex frame, duplex product on page 21 or Duplex frame
on page 47.
● Cartridge door. See Cartridge door, duplex product on page 29 or Cartridge door, simplex product
on page 23 or Cartridge door on page 48.
● Top cover. See Top cover on page 33 or Top cover on page 52.
1. Duplex models only: Release two tabs (callout 1), and then remove the duplex reverse guide (callout 2).
2
1
3. Remove one FFC (callout 1), remove four screws (callout 2), and then remove the fax PCA (callout 3).
5. Disconnect one connector (callout 1), and then release the wire harness (callout 2) from the guide
(callout 3).
Reinstallation tip: When the pickup assembly is reinstalled, place these wire harnesses in the guide
first, and then the wire harness from the ground connector in the previous step. This ensures that the
harnesses are long enough for the connectors to reach the engine controller PCA.
9. Remove six screws (callout 1), and then remove the pickup assembly (callout 2).
CAUTION: The ground spring on the assembly is not captive. Do not lose the spring when the
assembly is removed. See Reinstall the pickup assembly on page 75.
CAUTION: The gear is not captive. Do not lose the gear while servicing the product.
2 1
1. Make sure that the pickup assembly ground spring is correctly positioned when the assembly is
reinstalled.
Figure 1-111 Reinstall the pickup assembly (1 of 4; correct ground spring position)
TIP: Reach in from the front of the product to push and hold the plate down as the pickup unit is
installed.
Figure 1-113 Reinstall the pickup assembly (3 of 4; lift plate in raised position)
Figure 1-114 Reinstall the pickup assembly (4 of 4; lift plate in lowered position)
● Input tray assembly. See Input tray assembly on page 11 or Input tray assembly on page 36.
● Output tray assembly. See Output tray assembly on page 11 or Output tray assembly on page 37.
● Left cover. See Left cover, duplex product on page 12 or Left cover, simplex product on page 13 or Left
cover on page 37.
● Front cover assembly. See Front cover assembly on page 15 or Front cover assembly on page 38.
● Right cover. See Right cover, duplex product on page 16 or Right cover, simplex product on page 18 or
Right cover on page 40.
1. Release one tab (callout 1), and then remove the holder (callout 2).
NOTE: The scanner cover and plate are removed as one assembly.
TIP: When the cover is reinstalled, make sure that the black screws (callout 4) are installed in the
correct screw holes.
1
2 3
Duplex models only: Disconnect three connectors (callout 1 and callout 2).
CAUTION: The motor driver PCA is still connected to the product by the wire harnesses and a FFC.
5. Duplex models only: Release one tab (callout 1), and then remove the duplex-connector PCA
(callout 2).
CAUTION: The motor driver PCA is still connected to the product by the FFC.
7. Release the wire harness (callout 1) from the guide (callout 2).
1
2
9. Remove two screws (callout 1), and then remove the motor (callout 2).
1
2
● Input tray assembly. See Input tray assembly on page 11 or Input tray assembly on page 36.
● Output tray assembly. See Output tray assembly on page 11 or Output tray assembly on page 37.
● Left cover. See Left cover, duplex product on page 12 or Left cover, simplex product on page 13 or Left
cover on page 37.
● Front cover assembly. See Front cover assembly on page 15 or Front cover assembly on page 38.
● Right cover. See Right cover, duplex product on page 16 or Right cover, simplex product on page 18 or
Right cover on page 40.
● Rear cover (simplex product) or duplex door (duplex product). See Rear cover, simplex product
on page 22 or Duplex door, duplex product on page 20 or Duplex door on page 46.
● Duplex frame (duplex products only). See Duplex frame, duplex product on page 21 or Duplex frame
on page 47.
● Cartridge door. See Cartridge door, duplex product on page 29 or Cartridge door, simplex product
on page 23 or Cartridge door on page 48.
● Top cover. See Top cover on page 33 or Top cover on page 52.
1. Duplex models only: Release two tabs (callout 1), and then remove the duplex reverse guide (callout 2).
2
1
3. Remove four screws (callout 1), and then remove the fax PCA (callout 2).
5. Disconnect one connector (callout 1), and then remove the wire harness (callout 2) from the guide
(callout 3).
7. Remove one screw (callout 1), and then remove the pickup solenoid (callout 2).
● Input tray assembly. See Input tray assembly on page 11 or Input tray assembly on page 36.
● Output tray assembly. See Output tray assembly on page 11 or Output tray assembly on page 37.
● Left cover. See Left cover, duplex product on page 12 or Left cover, simplex product on page 13 or Left
cover on page 37.
● Front cover assembly. See Front cover assembly on page 15 or Front cover assembly on page 38.
● Right cover. See Right cover, duplex product on page 16 or Right cover, simplex product on page 18 or
Right cover on page 40.
● Rear cover (simplex product) or duplex door (duplex product). See Rear cover, simplex product
on page 22 or Duplex door, duplex product on page 20 or Duplex door on page 46.
● Duplex frame (duplex products only). See Duplex frame, duplex product on page 21 or Duplex frame
on page 47.
● Cartridge door. See Cartridge door, duplex product on page 29 or Cartridge door, simplex product
on page 23 or Cartridge door on page 48.
● Top cover. See Top cover on page 33 or Top cover on page 52.
1. Duplex models only: Release two tabs (callout 1), and then remove the duplex reverse guide (callout 2).
2
1
3. Remove four screws (callout 1), and then remove the fax PCA (callout 2).
5. Disconnect one connector (callout 1), and then release the wire harness (callout 2) from the guides
(callout 3).
7. Release the wire harness (callout 1) from the ground spring (callout 2).
2 1
9. Remove one screw with washer (callout 1), and then remove one more screw (callout 2).
NOTE: In addition to following the reverse order of removal, make sure that you complete these steps to
correctly install the transfer-wire harness.
1. Set the ground spring (callout 1) on the transfer-wire harness (callout 2).
1
2
● Input tray assembly. See Input tray assembly on page 11 or Input tray assembly on page 36.
● Output tray assembly. See Output tray assembly on page 11 or Output tray assembly on page 37.
● Left cover. See Left cover, duplex product on page 12 or Left cover on page 37.
● Front cover assembly. See Front cover assembly on page 15 or Front cover assembly on page 38.
● Right cover. See Right cover, duplex product on page 16 or Right cover on page 40.
1. Release one tab (callout 1), and then remove the holder (callout 2).
NOTE: The scanner cover and plate are removed as one assembly.
TIP: When the cover is reinstalled, make sure that the black screws (callout 4) are installed in the
correct screw holes.
1
2 3
3. Disconnect two connectors (callout 1), and then release the wire harness (callout 2) from the guides
(callout 3).
5. Remove one screw (callout 1), and then remove the duplex-reverse solenoid (callout 2).
● Input tray assembly. See Input tray assembly on page 11 or Input tray assembly on page 36.
● Output tray assembly. See Output tray assembly on page 11 or Output tray assembly on page 37.
● Left cover. See Left cover, duplex product on page 12 or Left cover, simplex product on page 13 or Left
cover on page 37.
● Front cover assembly. See Front cover assembly on page 15 or Front cover assembly on page 38.
● Right cover. See Right cover, duplex product on page 16 or Right cover, simplex product on page 18 or
Right cover on page 40.
1. Release one tab (callout 1), and then remove the holder (callout 2).
NOTE: The scanner cover and plate are removed as one assembly.
TIP: When the cover is reinstalled, make sure that the black screws (callout 4) are installed in the
correct screw holes.
1
2 3
3. Disconnect one connector (callout 1), and then release the wire harness (callout 2) from the guides
(callout 3).
When the main fan is reinstalled, make sure that the wire harness (callout 1) is correctly positioned, and that
the label (callout 2) on the fan faces the inside of the product.
● Input tray assembly. See Input tray assembly on page 11 or Input tray assembly on page 36.
● Output tray assembly. See Output tray assembly on page 11 or Output tray assembly on page 37.
● Left cover. See Left cover, duplex product on page 12 or Left cover, simplex product on page 13 or Left
cover on page 37.
● Front cover assembly. See Front cover assembly on page 15 or Front cover assembly on page 38.
● Right cover. See Right cover, duplex product on page 16 or Right cover, simplex product on page 18 or
Right cover on page 40.
● Front cover assembly. See Front cover assembly on page 15 or Front cover assembly on page 38.
1. Release one tab (callout 1), and then remove the holder (callout 2).
NOTE: The scanner cover and plate are removed as one assembly.
TIP: When the cover is reinstalled, make sure that the black screws (callout 4) are installed in the
correct screw holes.
1
2 3
CAUTION: The motor driver PCA is still connected to the product by the wire harnesses and a FFC.
5. Release one tab (callout 1), and then remove the duplex-connector PCA (callout 2).
TIP: The orientation of the FFC is important. When reinstalling it, make sure the blue tab is toward the
product right side. If the FFC is installed upside-down, the document feeder does not work.
● Document feeder core. See Document feeder core assembly on page 110.
● Document feeder core. See Document feeder core assembly on page 110.
CAUTION: Do not damage the FFC (circled) that runs through the document feeder base. Carefully
feed the FFC through the slot during removal and during replacement.
1
2
4. Temporarily set the left side of the document feeder base back onto its hinge, and then firmly lift the
document feeder base straight up to remove it from the scanner base.
● Covers
● Internal assemblies
ENWW 117
Order through service or support providers Contact an HP-authorized service or support provider.
Related documentation
HP LaserJet Pro M201/M202 Printer series User Guide Product user guide. Need part number
HP LaserJet Pro M201/M202 Printer series Service Manual English service manual (this N/A
manual)
118 Chapter 2 Parts and diagrams: HP LaserJet Pro M201/M202 Printer series ENWW
Service parts
NOTE: The parts in the following table are not shown in the assembly illustrations in this chapter.
UMBER 802.11N DUAL BAND STRA CONN (wireless products only) 1150-7957
NOTE: In this manual, the abbreviation “PCA” stands for “printed circuit-board assembly.” Components
described as a PCA might consist of a single circuit board or a circuit board plus other parts, such as cables
and sensors.
The figures in this chapter show the major subassemblies in the product and their component parts. A parts
list table follows each exploded view assembly diagram. Each table lists the item number, the associated
part number, and the description of each part. If a part is not listed in the table, then it is not a field
replacement unit (FRU).
120 Chapter 2 Parts and diagrams: HP LaserJet Pro M201/M202 Printer series ENWW
122 Chapter 2 Parts and diagrams: HP LaserJet Pro M201/M202 Printer series ENWW
124 Chapter 2 Parts and diagrams: HP LaserJet Pro M201/M202 Printer series ENWW
(PS701,702)
(J552)
(J702)
(J101)
(J531)
DUPLEX MODEL
(J10)
(J532)
(J11)
126 Chapter 2 Parts and diagrams: HP LaserJet Pro M201/M202 Printer series ENWW
3 Cable,flat RK2-6680-000 1
DUPLEX MODEL
(J551)
(PS751)
128 Chapter 2 Parts and diagrams: HP LaserJet Pro M201/M202 Printer series ENWW
DUPLEX MODEL
(J904)
(J571)
(J903)
(J1)
DUPLEX MODEL
DUPLEX MODEL
(J801) (SL2)
(J1102)
(J542)
(FM1)
(J1103)
(M1)
(J902)
130 Chapter 2 Parts and diagrams: HP LaserJet Pro M201/M202 Printer series ENWW
132 Chapter 2 Parts and diagrams: HP LaserJet Pro M201/M202 Printer series ENWW
Front cover assembly (duplex product) RM2-0411-000 External panels and covers,
duplex product on page 123
Front cover assembly (simplex product) RM2-0414-000 External panels and covers,
simplex product on page 125
134 Chapter 2 Parts and diagrams: HP LaserJet Pro M201/M202 Printer series ENWW
RM2-0411-000 Front cover assembly (duplex product) External panels and covers,
duplex product on page 123
RM2-0414-000 Front cover assembly (simplex product) External panels and covers,
simplex product on page 125
136 Chapter 2 Parts and diagrams: HP LaserJet Pro M201/M202 Printer series ENWW
● Covers
● Internal assemblies
ENWW 139
Order through service or support providers Contact an HP-authorized service or support provider.
Related documentation
HP LaserJet Pro MFP M225/M226 Printer series User Guide Product user guide. Need part number
HP LaserJet Pro M201/M202 Printer series Service Manual English service manual (this N/A
manual)
High-capacity black toner cartridge, HP LaserJet Pro MFP M225 CF283X CF484-67903
series
140 Chapter 3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ENWW
Service parts
NOTE: The parts in the following table are not shown in the assembly illustrations in this chapter.
Scanner:
ADF:
142 Chapter 3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ENWW
NOTE: In this manual, the abbreviation “PCA” stands for “printed circuit-board assembly.” Components
described as a PCA might consist of a single circuit board or a circuit board plus other parts, such as cables
and sensors.
The figures in this chapter show the major subassemblies in the product and their component parts. A parts
list table follows each exploded view assembly diagram. Each table lists the item number, the associated
part number, and the description of each part. If a part is not listed in the table, then it is not a field
replacement unit (FRU).
144 Chapter 3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ENWW
(PS701,702)
(J552)
(J702)
(J101)
146 Chapter 3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ENWW
(J551)
(PS751)
148 Chapter 3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ENWW
(J904)
(J571)
(J903)
(J1)
(J801)
(J542) (SL2)
(J1102)
(FM1)
(J1103)
(M1)
(J902)
150 Chapter 3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ENWW
6 Solenoid RK2-0420-000 1
7 Fan RK2-6694-000 1
152 Chapter 3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ENWW
10
7
8
6 9
5
154 Chapter 3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ENWW
156 Chapter 3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ENWW
6
3
5
3
158 Chapter 3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ENWW
160 Chapter 3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ENWW
162 Chapter 3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ENWW
164 Chapter 3 Parts and diagrams: HP LaserJet Pro MFP M225/M226 series ENWW
A D fuser
accessories document conventions iii reinstalling 61
ordering 118, 140 drive belt, main motor removing 56
after-service checklist 5 removing 82 fuser film assembly
duplex door, removing reinstalling 66
C M201 and M202 duplex removing 63
cartridge products 20
ordering 118, 140 M225 and M226 46 I
part number, M201 and M202 duplex frame, removing input tray
118 M201 and M202 duplex removing 11
part number, M225 and M226 products 21
140 M225 and M226 47 L
cartridge door, removing duplex-connector PCA, duplex laser/scanner assembly
M201 and M202 duplex products reinstalling 69
products 29 removing 102 removing 66
M201 and M202 simplex Duplex-reverse solenoid, duplex left cover, removing
products 23 products M201 and M202 duplex
M225 and M226 48 removing 96 products 12
cautions iii dust cover M201 and M202 simplex
checklists removing 11 products 13
after-service 5 M225 and M226 37
preservice 5 E
controller PCA, engine electrostatic discharge (ESD) 2 M
reinstalling 93 engine controller PCA main fan, duplex products
removing 88 reinstalling 93 reinstalling 101
conventions, document iii removing 88 removing 99
copy-quality test 5 ESD (electrostatic discharge) 2 main motor
customer self repair parts External panels, covers, and doors: removing 78
part numbers, M201 and M202 M201 and M202 main motor drive belt
119 removing and replacing 10 removing 82
customer self-repair (CSR)
components 8 F N
pickup roller 8 formatter PCA notes iii
separation pad 9 removing 54
customer-replaceable units (CRU) front cover, removing O
part numbers, M201 and M202 M201 and M202 15 ordering
119 M225 and M226 38 print cartridge 118, 140
product documents 118, 140
supplies and accessories 118,
140