Professional Documents
Culture Documents
Web p05627 Manual Facility 4t Hibrida Unificado Rev2
Web p05627 Manual Facility 4t Hibrida Unificado Rev2
Web p05627 Manual Facility 4t Hibrida Unificado Rev2
nd also when the gate is opening. Flashes three times = When releasing button CMD- or GRV+ (command has
- 328 Remote controls with Fixed Code (HT6P20B standard). Instructions: been denied to maximum and minimum values reached)
- 164 Remote Controls with Rolling Code (PPA standard). 1. The gate must be still;
-Inputs: 2. Close jumper PROG;
3. Press and release the CMD button (Twice);
7. BRAKE
- 02 x Photocells (Obstacle-detection and Closing-control).
FACILITY 4T TECHNICAL
- 01 x Pushbutton (opening and closing).
- 01 x CA Pushbutton (only opening).
4. Press and release the GRV button to enter the function;
5. Press the button GRV+ to increase or the button CMD- to decrease; It is activated when the motor is switched off through a command, or when
Settings:
ECU
- Outputs: 0 = Brake switched off.
- Courtesy Light Module. 4. ERASING REMOTE CONTROLS 1 = Time 0.150 seconds
2 = Time 0.300 seconds
- Electronic lock module. ...
It erases and boots the memory to add new remote controls.
- Traffic Light Module. 17 = Oscillation time 2.55 seconds.
WARNING: Before starting this function, check the remote control
- Deceleration ramp.
configuration, CR/CF resistor.
- Automatic Learning of the Opening / Closing Limits. Instructions:
- Obstacle-Detection with automatic movement reversion. 1. The gate must be still;
Instructions: 2. Close jumper PROG;
- Delay Timing when opening using a traffic light. 1. The gate must be still; 3. Press and release the CMD button (Five times);
2. Close jumper PROG; 4. Press and release the GRV button to enter the function;
3. Press and release the CMD button (Three times); 5. Press button CMD- to decrease, button GRV+ to increase or Open jumper
WARNING 4. Press and release the GRV button to enter the function; PROG (Cancel function).
First programming (setting) after installing or defining a new 5. Press button GRV+ to erase the memory of the remote controls or button
type of remote control: CMD- / Open jumper PROG (Cancel function). SN LED Signs:
This procedure will reset the memory (erase old information / Flashes once = When releasing button CMD- and/or GRV+ (command has
prepare the memory to receive new remote controls). 5. ADDING REMOTE CONTROLS been accepted).
Flashes three times = When releasing button CMD- or GRV+ (command has
Remote Controls with PPA Standard (Fixed and Rolling Codes) are been denied to maximum and minimum values reached)
supported.
1. Selecting type of remote control:
With a resistor = PPA Rolling Code.
Without a resistor = Fixed Code.
WARNING: In order to properly add remote controls, ensure that the memory 8. TRAFFIC LIGHT (SIN) INTERVAL TIME
has been initialized correctly with the corresponding remote control (Fixed /
Rev. 22
WARNING 2. Erase a remote control (Refer to item “ERASING REMOTE CONTROLS”) Rolling Code). When the gate is either opening, closing or open still, the relay module
P05638 - Rev.
manual first. If one has pressed the button CMD- by mistake and then
Settings:
2. DEFAULT FACTORY SETTINGS the button GRV+, the ECU will enter Default Factory Settings
mode and the LED will remain lit for ten seconds. In order to 0 = Module on.
cancel this function, open the jumper PROG. 1 = Oscillation time 0.5 second
Restore the settings to the default factory settings.
2 = Oscillation time 1.0 second
SETTING COMMANDS CHART Instructions: ...
1. The gate must be still; 20 = Oscillation time 10.0 seconds
2. Close jumper PROG; Instructions:
3. Press and release the CMD button (Once); 1. The gate must be still; Instructions:
4. Press and release the GRV button to enter the function; 2. Close jumper PROG; 1. The gate must be still;
5. Press button GRV+ to set as Default Factory Settings; or button CMD- / 3. Press the button on the remote control one wants to add; 2. Close jumper PROG;
Open jumper PROG (Cancel function). 4. The SN LED will flash rapidly; 3. Press and release the CMD button (Six times);
5. Press and release the button GRV+; 4. Press and release the GRV button to enter the function;
DEFAULT FACTORY SETTINGS CHART 5. Press button CMD- to decrease, button GRV+ to increase or Open jumper
6. The SN LED will flash once (button has been added), twice (button
COMMAND WHEN OPENING Enabled already added) or three times (memory full); PROG (Cancel function).
DELAY TIME WHEN OPENING USING A TRAFFIC LIGHT 0 (DISABLED) 7. Release the button on the remote control;
COURTESY LIGHT 60 seconds 8. Go back to step 3 to add a new button of the remote control; SN LED Signs:
BRAKE ACTIVATION TIME 150.0 msec 9. In order to finish, open jumper PROG. Flashes once = When releasing button CMD- and/or GRV+ (command has
TRAFFIC LIGHT On been accepted).
REVERSION THROUGH A COMMAND Allowed 6. COURTESY LIGHT (LG) INTERVAL TIME Flashes three times = When releasing button CMD- or GRV+ (command has
END-OF-STROKE Hybrid been denied to maximum and minimum values reached).
TORQUE (STRENGTH) WHEN LEARNING THE When the gate is either opening, closing or open still, the relay module
Level 20 keeps switched on.
OPENING LIMITS
TORQUE (STRENGTH) WHEN LEARNING THE CLOSING LIMITS Level 20 When the ECU finishes the closing cycle, the relay module will be switched 9. REVERSION THROUGH A COMMAND
ELECTRONIC LOCK RAMP 0% off after the set time.
OPENING RAMP SETTING 0% It allows the pushbutton or remote control to work when the gate is closing
Settings: in order to reverse its direction.
AUTOMATIC CLOSING TIME FOR CLOSING-CONTROL
12 seconds 0 = Minimum time 1.0 second
PHOTOCELL
1 = Intermediate time 15.0 seconds Instructions:
2 = Intermediate time 30.0 seconds 1. The gate must be still;
3. COMMAND WHEN OPENING ... 2. Close jumper PROG;
17 = Maximum time 255.0 seconds 3. Press and release the CMD button (Seven times);
It allows a command from a pushbutton or remote control to work while
the gate is opening. 4. Press and release the GRV button to enter the function;
Instructions:
It also has the function of programming the pushbutton / remote control 5. Press button GRV+ to enable the reversion through a command or the
1. The gate must be still;
operation mode when counting time for opening delay while the traffic button CMD- to disable the reversion through a command.
2. Close jumper PROG;
light is on. 6. In order to finish, open jumper PROG.
One can cancel the opening delay time through a pushbutton or remote 3. Press and release the CMD button (Four times);
control. 4. Press and release the GRV button to enter the function;
5. Press button CMD- to decrease, button GRV+ to increase or Open jumper 10. SELECTING TYPE OF END-OF-STROKE
1. MAIN FEATURES Settings: PROG (Cancel function).
0 = command when opening enabled. Analog end-of-stroke system (reed-switch), Reed Digital (Sensor Hall) or
- Analog, Encoder-Digital or Hybrid End-of-Stroke. 1 = Partial command when opening, enabled only on the opening delay SN LED Signs: Hybrid (Analog system + reed digital). After selecting the type of end-of-
- RF 433,92 MHz Receiver module. using a traffic light and disabled when the gate is opening. Flashes once = When releasing button CMD- and/or GRV+ (command has
2 = total command when opening, disabled on the opening delay using a stroke, the ECU will enter the path acquiring mode automatically after the
been accepted). command.
Instructions: Instructions: movement direction to open. After finishing opening, it will count the time
1. The gate must be still; 1. The gate must be still;
19. TRIMPOT FOR ADJUSTING OPENING / to start the closing cycle if the ECU has been set to automatic mode.
2. Close jumper PROG; 2. Close jumper PROG; CLOSING RAMP While it is counting the time to close automatically, whenever it receives a
3. Press and release the CMD button (Eight times); 3. Press and release the CMD button (12 times) to enter the function; signal from the photocell, the ECU will restart the counting of the automatic
4. Press and release the button GRV; It will adjust the distance of the deceleration ramp at the end of the opening closing time. While the photocell is blocked, the counting of the time to
4. Press and release the GRV button to enter the function;
5. Press button CMD- to decrease, button GRV+ to increase. / closing path, in order to decrease the gate speed. close automatically will be reset; when it is released, the counting of time
5. Press button GRV+ to increase or button CMD- to decrease. (0 = Analog,
6. In order to finish, open jumper PROG. will be restarted.
1 = Reed Digital and 2 = Hybrid) Trimpot range = from 0% up to 50% from the acquired path.
6. In order to finish, open jumper PROG. Counterclockwise: decrease the ramp -FOT2 (Obstacle-detection and Closing-Control E.g.: Application for
Clockwise: Increase the ramp. automatic barriers)
WARNING FOT2 input does not recognize the automatic / semiautomatic (push-to-
WARNING In case the function is disabled (level 0), the setting of the WARNING: In case the parameter “OPENING RAMP SIZE ADJUSTMENT” is close) settings (A/S jumper and PAUSA trimpot); it only recognizes the
- Analog mode: use only FCA (Opening End-of-Stroke) input. RAMPA (ramp) trimpot will be used to both sides (Opening in a level other than zero, the adjustment chosen on this trimpot will be setting for Closing-Control Time (function 13).
The input for the signal of the digital encoder will be disabled, and closing). used only for closing. In case the function 12 is disabled, this trimpot will During the closing cycle, whenever it receives a signal from FOT2 photocell,
i.e., it will not work. operate for both opening and closing. it wil lreverse the movement direction and will count the time to close
Otherwise (a level different from 0), the distance of the ramp
- Digital or Hybrid Mode: Both inputs will be enabled. If the automatically (function 13).
for closing will be defined by the RAMPA trimpot and the In case the FOT2 input is blocked when it is counting the time to close
application is only digital, use the ENCODER input; if the appli-
cation is hybrid, use the ENCODER and FCA inputs.
setting of function 12 (Adjustment on opening ramp) will be 20. CLOSING-CONTROL PHOTOCELL TIME automatically, this timing will be on reset mode and as soon as it is released,
used for the opening cycle. this time will be reset.
Time for automatic closing of the closing-control photocell. During the opening cycle, if the ECU receives a pulse on the FOT2 input, it
will be stored in the memory and will count the time to close automatically
Settings: whenever the opening cycle is over.
11. TORQUE (STRENGTH) WHEN 14. AUTOMATIC CLOSING (PAUSE) 60 adjustment levels.
LEARNING THE OPENING / CLOSING 1 = 1 second 21. OPENING DELAY WHEN USING A
LIMITS (DIGITAL ECU) Semiautomatic Mode (Push-to-close – A/S Jumper closed) 2 = 2 seconds
After a complete opening cycle, a new command for closing 3 = 3 seconds TRAFFIC LIGHT
It is automatically activated whenever it is acquiring the path or after the will be necessary. ...
60 = 60 seconds When the gate is totally closed and still, whenever it receives a command for
ECU has been connected to a power supply, in order to reach the first stop an opening cycle, the traffic light will be activated and will remain switched
plate. on for the set time interval; then the motor will be activated.
WARNING: This function is only available to the Digital / Hybrid End-of- Operations:
Automatic Mode (A/S Jumper open) 1. The gate must be still; The traffic light will be switched off when the closing cycle is over, or
Stroke system. It cannot be used on the analog end-of-stroke system. whenever it receives a new command through the remote control during
After a complete opening cycle, the set PAUSA (pause) time 2. Jumper PROG must be open;
is decreased every second; when it reaches zero, the closing 3. Press and release the CMD button (13 times); the delay acquiring.
Settings:
33 adjustment levels. cycle will be initiated. 4. Press and release the GRV button;
5. Press button CMD- to decrease, button GRV+ to increase. Settings:
0 = level 1. 0 = delay disabled.
... 6. In order to finish, open jumper PROG.
1 = 1-second delay.
32 = level 32 15. PAUSE TIME (ONLY FOR AUTOMATIC Operations: 2 = 2-second delay.
Instructions: MODE) -CA (Command only for opening) ...
If the gate is closed or half-open, whenever it receives a command, it will 15 = 15-second delay.
1. The gate must be still;
2. Close jumper PROG; Counterclockwise: decrease time interval. (Minimum = 1 second) open.
Clockwise: Increase time interval. (Maximum = 4 minutes) If the gate is closing, whenever it receives a command, it will reverse the Instructions:
3. Press and release the CMD button (Nine times) to acquire torque control 1. The gate must be still;
when opening and (Ten times) when closing; movement direction to open.
-CF (Command only for closing) 2. Close jumper PROG;
4. Press and release the GRV button;
5. Press button CMD- to decrease, button GRV+ to increase. 16. ERASING THE PATH If the gate is open or half-open, whenever it receives a command, it will 3. Press and release the CMD button (Fourteen times);
close. 4. Press and release the GRV button to enter the function;
6. In order to finish, open jumper PROG. 5 Press button CMD- to decrease, button GRV+ to increase;
Instructions: If the gate is opening, whenever it receives a command, it will reverse the
1. The gate must be still; movement direction to close. 6. In order to finish, open jumper PROG.
12. PATH COVERED WHEN ACTIVATING 2. Jumper PROG must be open;
THE ELECTRONIC LOCK (CLOSING) 3. Keep button GRV+ pressed for 3.0 seconds; the SN LED will flash, -FOT1 (Obstacle-detection)
indicating it has performed the operation. When closing, if it receives a signal from FOT1 photocell, it will reverse the
22. WIRING DIAGRAM
It adjusts the distance of the closing path to activate the electronic lock.
13. SETTING THE SIZE OF THE OPENING 18. RAMP TORQUE (STRENGTH)
RAMP
This adjustment will decrease the gate speed when its path is into the
It allows to individually setting the distance of the opening ramp to enter in Deceleration ramp defined by the RAMPA (ramp) trimpot. In case the
torque control mode to decrease the gate speed. ramp is disabled through the RAMPA trimpot, the torque control will be
inoperative.
Settings:
51 adjustment levels. Trimpot range = 60 levels.
0 = function disabled. Counterclockwise: decrease torque control
5 = 5% of the total path. Clockwise: Increase torque control
10 = 10% of the total path.
15 = 15% of the total path.
...
50 = 50% of the total path.
- Código de aprendizaje encriptado con memoria externa: 2 = comando en la apertura total, deshabilitado durante el retardo en la Señalizaciones del LED SN:
- 328 Transmisores de código fijo (estándar HT6P20B). apertura con señalera y también durante el ciclo de apertura del portón. Parpadea 1x = Al liberar el botón CMD- y / o GRV + (comando aceptado).
- 164 Transmisores de código rotativo (estándar PPA). Parpadea 3x = Al liberar el botón CMD- o GRV + (comando negado para
Operaciones:
-Entradas para: valores mínimo y máximo alcanzado).
1. El portón debe estar parado;
CENTRAL DE COMANDO - 02 x Fotocélulas (antiaplastamiento y seguidora). 2. Cierre el jumper PROG;
- 01 x Botonera (apertura y cierre). 3. Presione y suelte el botón CMD (2x); 7. FRENO
MANUAL
FACILITY 4T TÉCNICO
- 01 x Botonera CA (sólo apertura).
- 01 x Botonera CF (sólo cierre).
4. Presione y suelte el botón GRV para entrar en la función;
5. Botón GRV + para aumentar el valor, o, el botón CMD- para disminuir
É acionado ao desligar o motor por comando, ou, ao encontrar os sensores
HÍBRIDA - Módulo receptor RF externo.
- Salidas para:
el valor;
6. Para finalizar, retire el jumper de PROG. analógicos (finais de curso).
ATENCIÓN 2. Borrar transmisor (ver tema “BORRANDO TRANSMISORES”) inicializado correctamente con el correspondiente tipo de transmisor de
P05627 - Rev.
Restaurar las configuraciones para el predeterminado de fábrica. botón GRV+, la central entrará en el modo de configuración Valores:
predeterminada de fábrica y el LED quedará encendido por 0 = módulo conectado.
TABELA DE COMANDO PARA Operaciones: 10seg. Para cancelar esta función, retire el jumper PROG. 1 = Tiempo oscilación 0,5 segundos
CONFIGURAÇÕES 1. El portón debe estar parado; 2 = Tiempo oscilación 1,0 segundo
2. Cierre el jumper PROG; ...
Tabla de comandos para configuraciones 3. Presione y suelte el botón CMD (1x); Operaciones: 20 = Tiempo de oscilación 10,0 segundos
Estándar de fábrica Selecciona función Entra en la función Cancelar 4. Presione y suelte el botón GRV para entrar en la función; 1. El portón debe estar parado;
1 x CMD- 1 x GRV+ 1 x GRV+ 1 x CMD- 5. Botón GRV + para configurar el estándar de fábrica, o, Botón CMD- o 2. Cierre el jumper PROG; Operaciones:
Comando en la Selecciona función Entra en la función Habilitar Deshabilitar
apertura 2 x CMD- 1 x GRV+ 1 x GRV+ 1 x CMD- Retirar el jumper PROG (Cancelar función). 3. Presione el botón del transmisor que desea grabar; 1. El portón debe estar parado;
Borrando Selecciona función Entra en la función Cancelar 4. El LED SN debe parpadear rápido; 2. Cierre el jumper PROG;
transmisores 3 x CMD- 1 x GRV+ 1 x GRV+ 1 x CMD- 5. Presione y suelte el botón GRV +; 3. Presione y suelte el botón CMD (6x);
Tiempo Luz de Selecciona función Entra en la función Incrementar Decrementar CONFIGURACIONES ESTÁNDAR DE FÁBRICA
Garaje (LG) 4 x CMD- 1 x GRV+ GRV+ CMD- 6. LED SN parpadea 1 vez (botón grabado) o parpadea 02 veces (botón del 4. Presione y suelte el botón GRV para entrar en la función;
COMANDO EN LA APERTURA Habilitado
Selecciona función Entra en la función Incrementar Decrementar transmisor ya grabado) o 03 veces (memoria llena); 5. Botón CMD- para decrementar valor, o, Botón GRV + para aumentar el
Freno
5 x CMD- 1 x GRV+ GRV+ CMD- TIEMPO RETARDO EN LA APERTURA CON SEÑALERA 0 (Deshabilitado) 7. Liberar el botón del transmisor; valor, o, Retirar el jumper PROG (Cancelar función).
Tiempo Señalera Selecciona función Entra en la función Incrementar Decrementar LUZ DE GARAJE 60 seg 8. Vuelva al paso 3 para grabar un nuevo botón del transmisor;
(SIN) 6 x CMD- 1 x GRV+ GRV+ CMD-
TIEMPO ACCIONAMIENTO FRENO 150,0 mseg 9. Para finalizar, retire el jumper PROG.
Reversión por el Selecciona función Entra en la función Habilitar Deshabilitar Señalizaciones del LED SN:
comando 7 x CMD- 1 x GRV+ 1 x GRV+ 1 x CMD- SEÑALERA Encendida
Parpadea 1x = Al liberar el botón CMD- y / o GRV + (comando aceptado).
Incrementar Decrementar REVERSIÓN POR EL COMANDO Permitido
Seleccionando tipo Selecciona función Entra en la función
GRV+ CMD- Parpadea 3x = Al liberar el botón CMD- o GRV + (comando negado a
de fin de carrera 8 x CMD- 1 x GRV+
(0=Analógico, 1=Reed Digital e 2=Híbrido)
TIPO FIN DE CARRERA Híbrido 6. TIEMPO LUZ DE GARAJE (LG) valores mínimo y máximo alcanzado).
Torque (fuerza) de
Selecciona función Entra en la función Incrementar Decrementar
TORQUE DE APERTURA EN LA MEMORIZACIÓN Nivel 20
memorización en la
9 x CMD- 1 x GRV+ GRV+ CMD- TORQUE DE CIERRE EN LA MEMORIZACIÓN Nivel 20 Durante el ciclo de apertura o cierre del portón o parado abierto, el módulo
apertura
Torque (fuerza) de RAMPA DE LA ELECTROCERRADURA 0% de relé quedará encendido. 9. REVERSIÓN POR EL COMANDO
Selecciona función Entra en la función Incrementar Decrementar
memorización en el
10 x CMD- 1 x GRV+ GRV+ CMD- AJUSTE RAMPA APERTURA 0% Cuando la central termine el ciclo de cierre, el módulo de relé se apagará
cierre
TEMPO DE FECHAMENTO AUTOMÁTICO PARA después de un tiempo programado. Permiso de comando para que la botonera o el transmisor funcionen
Recorrido para 12 segundos
accionamiento de la Selecciona función Entra en la función Incrementar Decrementar FOTOCÉLULA SEGUIDORA durante el recorrido de cierre del portón para la reversión.
electrocerradura 11 x CMD- 1 x GRV+ GRV+ CMD- Valores:
en el cierre
0 = Tiempo mínimo 1,0 segundos Operaciones:
Ajuste del
tamaño de la
Selecciona función Entra en la función Incrementar Decrementar 3. COMANDO EN LA APERTURA 1 = Tiempo intermedio 15,0 segundos 1. El portón debe estar parado;
12 x CMD- 1 x GRV+ GRV+ CMD-
rampa de apertura 2 = Tiempo intermedio 30,0 segundos 2. Cierre el jumper PROG;
Tiempo de cierre Permiso para que el comando de la botonera o el transmisor funcionen
Selecciona función Entra en la función Incrementar Decrementar durante el recorrido de apertura del portón. ... 3. Presione y suelte el botón CMD (7x);
automático para
fotocélula seguidora
13 x CMD- 1 x GRV+ GRV+ CMD-
También tiene la función de programar el modo de operación de la 17 = Tiempo máximo 255,0 segundos 4. Presione y suelte el botón GRV para entrar en la función;
Retardo en la Selecciona función Entra en la función Incrementar Decrementar botonera o transmisor durante el recuento de tiempo de retardo en la 5. Botón GRV + para habilitar el comando de reversión, o el botón CMD-
apertura con señalera 14 x CMD- 1 x GRV+ GRV+ CMD- apertura con señalera encendida. Operaciones: para deshabilitar el comando de reversión.
El tiempo de retardo en la apertura del portón puede ser cancelado por la 1. El portón debe estar parado;
botonera o el transmisor. 6. Para finalizar, retire el jumper PROG.
2. Cierre el jumper PROG;
1. PRINCIPALES CARACTERÍSTICAS Valores: 3. Presione y suelte el botón CMD (4x); 10. SELECCIONANDO TIPO DE FIN DE
0 = comando en la apertura habilitada. 4. Presione y suelte el botón GRV para entrar en la función;
- Fin de carrera analógico, encoder digital o híbrido. 1 = comando en la apertura parcial, habilitado solamente durante el retardo 5. Botón CMD- para decrementar valor, o, Botón GRV+ para aumentar el
- Módulo receptor RF 433,92 MHz. en la apertura con señalera y deshabilitado durante el ciclo de apertura del valor, o, Retirar el jumper PROG (Cancelar función).
portón.