This document provides a thermowell calculation report according to ASME PTC-19.3-2010 standards. It analyzes thermowell TW-1 for use in a natural gas line with a temperature of 60C, pressure of 85 bar, and maximum fluid velocity of 14m/s. The report calculates dimensions, material properties, stresses, and other non-dimensional numbers to verify the thermowell can withstand the maximum expected operating conditions without failure or resonance issues. The analysis found the thermowell is acceptable for the given process conditions up to 14m/s.
This document provides a thermowell calculation report according to ASME PTC-19.3-2010 standards. It analyzes thermowell TW-1 for use in a natural gas line with a temperature of 60C, pressure of 85 bar, and maximum fluid velocity of 14m/s. The report calculates dimensions, material properties, stresses, and other non-dimensional numbers to verify the thermowell can withstand the maximum expected operating conditions without failure or resonance issues. The analysis found the thermowell is acceptable for the given process conditions up to 14m/s.
This document provides a thermowell calculation report according to ASME PTC-19.3-2010 standards. It analyzes thermowell TW-1 for use in a natural gas line with a temperature of 60C, pressure of 85 bar, and maximum fluid velocity of 14m/s. The report calculates dimensions, material properties, stresses, and other non-dimensional numbers to verify the thermowell can withstand the maximum expected operating conditions without failure or resonance issues. The analysis found the thermowell is acceptable for the given process conditions up to 14m/s.
This document provides a thermowell calculation report according to ASME PTC-19.3-2010 standards. It analyzes thermowell TW-1 for use in a natural gas line with a temperature of 60C, pressure of 85 bar, and maximum fluid velocity of 14m/s. The report calculates dimensions, material properties, stresses, and other non-dimensional numbers to verify the thermowell can withstand the maximum expected operating conditions without failure or resonance issues. The analysis found the thermowell is acceptable for the given process conditions up to 14m/s.
Thermowell Calculation Report according ASME-PTC-19.
3-2010
Tag N° TW-1 / TW-2 / TW-3
Drawings Fluid Natural Gas Fluide natual state Gas Dynamic Viscosity μ 1.00E-02 [cP] PROCESS DATA Operating Temperature T 60.00 [°C] Operating Pressure P 85 [Bar] Density ρ 59.92 [kg/m3] Process Fluid Velocity V 14 [m/s] Size Pipe Inside diameter ID 146.36 [mm] LINE DIMENSIONS Wall Thickness TPW 10.97 [mm] Nozzle Inside diameter 'IDSupport' 34.02 [mm] Height to Pipe OD 'HOD' 112 [mm] Model Code Mounting Configuration RF Process Connection 1'' 1/2600# RF Material SS 316 Unsupported Length'L' 200 [mm] Protruding Length 'PL' 77.03 [mm] THERMOWELL DIMENSIONS Stem Root Diameter 'A' 22 [mm] Reduced Diameter Length 'Ls' 0 [mm] Tip Diameter 'B' 22 [mm] Style 1-Piece Forged Flanged- Flanged- Flanged- Lap 1-Piece 0.6 Threade Welded Frequency ratio 0.4 Bore Bore diameter 'd' 7 [mm] Partial Full Van Flange Forged d 0.80 Fillet Fillet Radius at Root 'b' 4 [mm] 0.60 Material Density ρm 8030 [kg/m3] 0.40 Mod of Elasticity at Op. Temp. E 1.98E+11 [Pa] 0.20 Material Properties Max Allowable Working Stress S 1.60E+08 [Pa] Fatigue Endurance Limit Sf x FT 0.00 4.83E+07 [Pa] 0 5 10 15 Von Mises Stress Limit 2.40E+02 [Pa] Reynolds Number 'Re' 1.85E+06 Velocity (m/s) Non Dimensionals Numbers Strouhal Number 'Ns' 2.20E-01 Scruton Number 'Nsc' 5.94E-01 So,max Dynamic Stress (Pa) Insitu Natural Frequency fnc Allowable 3.60E+02 [Hz] 6.0E+07 Frequency Calculations Strouhal Frequency fs 1.40E+02 [Hz] 5.0E+07 Frequency Ratio fs/fnc 0.39 1 In-Line Resonance Velocity VIR 4.0E+07 6.67E+00 [m/s] Allowable Check for inline Resonance Cyclic Stress at Support plane 'So,max' 9.03E+07 [Pa] 4.93E+07 [Pa] 3.0E+07 0 Cyclic Stress at Reduced Dia So,max (Stepped Only) 0.00E+00 [Pa] 0.00E+00 [Pa] 2.0E+07 Steady State Drag Stress at Support Plane 'Smax' 1.16E+07 [Pa] 2.40E+08 [Pa] 1 Steady State Stresses Steady State Drag Stress at Reduced Dia. Smax 1.0E+07 0.00E+00 [Pa] 0.00E+00 [Pa] (Stepped Only) Dynamic Stress at Support Plane So,max 4.80E+06 [Pa] 4.93E+07 [Pa] 0.0E+00 1 Dynamic Stresses Dynamic Stress at Reduced Dia. So,max (Stepped 0.00E+00 [Pa] 0.00E+00 [Pa] 0 2 4 6 8 10 12 14 16 Only) Velocity (m/s) Pressure Check Max Stem Pressure Pc 8.50E+06 [Pa] 6.92E+07 [Pa] 1 Result Thermowell is acceptable for process conditions. Comments Maximum velocity cosidered is 14 m/s. No higher in-line resonance velocity is considered. Thermowell is acceptable upto a service velocity of 14 m/s.