Professional Documents
Culture Documents
Liftmedia User Manual v10
Liftmedia User Manual v10
Liftmedia User Manual v10
USER MANUAL
CONTENT
1. Introduction .................................................................................................................................................................. 3
1.1. Functions ................................................................................................................................................................. 3
1.2. Technical features ................................................................................................................................................... 4
2. System Components...................................................................................................................................................... 6
3. General Overview and Electrical Connections .......................................................................................................... 7
3.1. Liftmedia-P ............................................................................................................................................................. 7
3.1.1. LiftMedia-P General Overview ....................................................................................................................... 7
3.1.2. Liftmedia-P Electrical Connections ................................................................................................................ 8
3.1.3. Liftmedia-P Paralel Mode Input Signals ......................................................................................................... 9
3.2. Liftmedia-S ........................................................................................................................................................... 10
3.2.1. Liftmedia-S General Overview ..................................................................................................................... 10
3.2.2. Liftmedia-S Electrical Connections .............................................................................................................. 10
4. Adjustment .................................................................................................................................................................. 11
4.1. Viewing angle adjustment ..................................................................................................................................... 11
4.2. Time, Date and Input Mode Settings for LiftMedia-P .......................................................................................... 12
5. Required Components ................................................................................................................................................ 13
6. SD-Card Content ........................................................................................................................................................ 13
7. LiftMedia Design Process ........................................................................................................................................... 14
8. To Start The Design .................................................................................................................................................... 14
9. LiftMedia Designer Software Usage.......................................................................................................................... 15
9.1. Menu bar ............................................................................................................................................................... 15
9.2. Screen components ............................................................................................................................................... 16
9.2.1. Display components ...................................................................................................................................... 16
9.2.2. Sound designer .............................................................................................................................................. 17
9.2.3. General Settings ............................................................................................................................................ 18
10. Compiling the Project and Transferring Data to LiftMedia................................................................................. 19
11. Firmware Update ...................................................................................................................................................... 20
12. Dimensional Drawings.............................................................................................................................................. 21
12.1. LiftMedia-P ......................................................................................................................................................... 21
12.2. LiftMedia-S ......................................................................................................................................................... 22
12.3. Loudspeaker ........................................................................................................................................................ 22
13. Troubleshooting ........................................................................................................................................................ 23
14. User Manual Revision History................................................................................................................................. 24
07/2010 2 LiftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
1. Introduction
LiftMedia is a TFT LCD display, music and announcement system designed for lifts. LiftMedia Designer is
a user-friendly software to customize your displays. With its advanced and flexible graphic user interface,
you can set up all display properties including: floor names, floor pictures, direction arrows, logo,
background images, special messages, date, time, temperature, voice announcements and audio/video
playback.
Note: Horizontal and vertical screen orientation selection will be set while designing LiftMedia Designer.
No hardware changing is necessary.
1.1. Functions
07/2010 3 LiftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
Display properties
Screen type 5.7” TFT screen
LCD resolution 320 x 240 pixels
Viewing area 115.2 x 86.4 mm
LCD type TFT, negative
Backlight LED, white
Viewing angle (horizontal) +60° / -60° (horizontal axis)
(Contrast ratio ≥ 10) +50° / -55° (vertical axis)
Contrast Ratio 400:1
Dot pitch 0.12 x 0.36 mm
Backlight Lifetime 50.000 hours
Electrical properties
15 .. 28VDC (normal operation)
Supply Voltage Range
12 .. 15VDC (operation in emergency state, with low backlight)
LiftMedia-S 4-pin CANbus plug
Supply
External supply (Parallel interface)
input LiftMedia-P
4-pin CANbus plug (Serial interface)
130-140mA, for 24 VDC (normal operation)
Power consumption
80-90mA, for 24 VDC (standby operation, TFT screen backlight is off)
LiftMedia-S CANbus serial communication (with ARL-500)
Parallel interface: Binary / Gray / Arkel M1 counter
Operating modes
CANbus serial communication (with ARL-500)
Paralel interface 0 - 28 VDC (Logic 1: 4.3-28Vdc, Logic 0: 0-4.2Vdc)
Signal signal voltage (isolated with dual channel opto-coupler)
interface LiftMedia-P positive or negative common is selectable with GCOM
Parallel interface terminal for G0…G5, 31 and 32 signals
common signal positive or negative common is selectable with ICOM
selection terminal for 02, 804, DD, YAN, DEP, 41, 42 and I1
signals
Multimedia features
Picture formats bmp, jpeg, gif and png
Music/Video formats mp3, mpeg, avi, wmv, flv, mp4, m4u and wav
Video area About ¼ of the screen
Amplifier output 1 Watt, Ro = 8 ohm
Storage capacity Equal to SD-card capacity
Sound Quality 8-bit 30 kHz
07/2010 4 LiftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
The four sides of the 7mm wide breakable sections of the pcb board are included within the dimensions.
LiftMedia-S 275 g
Weight
LiftMedia-P 332 g
Appropriate conditions
Temperature for operation 0 °C - 50 °C
Temperature
Temperature for storage -10°C - 60 °C
Moisture %0 - %90 (non-condensing)
07/2010 5 LiftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
2. System Components
LiftMedia
LiftMedia-S or LiftMedia-P
SD-card
The SD-card that is sent with the LiftMedia has 2GB data storage capacity.
This capacity can be increased to 32 GB with SD, SDHC Class-2 or higher
SD-cards. With appropriate adaptor, mini or midi memory cards could be
used upon request.
SD-card includes the LiftMedia Designer software and a sample project.
Loudspeaker
Temperature sensor
07/2010 6 LiftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
3.1. Liftmedia-P
3
5 9 10 11
8
4
13
12
6
14
7
1
Figure-1
07/2010 7 LiftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
Common of signals
G0-G5, 31, 32
Sensor
Temperature sensor
Temp.
connection
Loudspeaker connection
Moving down 8Ohm / Min. 0.5W
Moving up +: Orange, -: Brown
Collecting down
Collecting up SERIAL MODE OPERATION
Fire
Earthquake (+)
(-) 15 .. 28Vdc power supply
Car light output
Common of signals
41, 42, 02, DD, 804, YAN, DEP, I1 LiftMedia-P
Figure-2
Input signals
Input modu
GCOM G0 G1 G2 G3 G4 G5 31 32 41 42 02 DD 804 YAN DEP I1 ICOM
*: Inputs signals are dual channel opto-coupled. Positive or negative common is applicable.
Connect GCOM / ICOM to negative if input signals are positive, connect GCOM / ICOM to positive if
input signals are negative.
07/2010 8 LiftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
07/2010 9 LiftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
3.2. Liftmedia-S
8
3 7
2
4
10
Figure-3
LiftMedia-S
CANH
CANL
Temp.
1000
100
Sensor
Figure-4
07/2010 10 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
4. Adjustment
To let the users get the best view of LiftMedia display, there is a jumper setting at the back of the board. This
jumper setting can make the screen turn by 180o. This setting should be done according to the position of the
LiftMedia.
Figure-5
You can use the following method to set the viewing angle of LiftMedia:
07/2010 11 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
When LiftMedia-P is energized, time, date and input mode settings should be done. When the “Press&hold
ENT for settings” message (see Figure-6) appears on the screen, press&hold “Ent.” button at the back of the
LiftMedia.
Figure-6
Note: If LiftMedia-P is connected to ARL-500 lift control system via CANbus serial connection, only setting
the “Input” parameter to “CANbus” will be enough. Date and time information is taken from ARL-500 lift
controller.
After making the settings, come to “OK” and press the “+” button to save your settings and exit the menu.
While working on this screen, when no action is taken for 2 minutes, LiftMedia will automatically exit the
menu and go into normal operation without saving the settings.
Ti m e / S a a t : 00:00
D a t e / Ta r i h : 0 1 / 0 1 / 2 0 1 0
Input/Giris : Gray
OK
Figure-7
07/2010 12 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
5. Required Components
The followings are required to create a design and load it to LiftMedia:
• LiftMedia Designer: The software used for creating a design and making the operation settings of
LiftMedia. “LiftMedia Designer Setup.msi” setup file can be found in the SD-card (in the "extras /
LiftMedia Setup" folder) or at www.arkel.com.tr website.
• Microsoft .NET Framework: A software package required to run the LiftMedia Designer tool in
Windows XP and previous operating systems (comes installed in Windows Vista and 7). If you
receive an error while running, you have to download and install this package.
• Audio&Video Codec Pack: A collection of codecs may be needed to play audio and video files.
The setup file of “K-Lite Codec Pack” can be found at www.arkel.com.tr website.
• SD-card reader: This is required to read/write the SD-card comes with the LiftMedia.
6. SD-Card Content
The SD-card comes with LiftMedia contains the following folders:
• “arkel”: LiftMedia device searches the compiled design in this folder. This folder must exist all the
time for LiftMedia to be able to operate. When you create or edit a project, you must compile the
project and copy the created folder (named "arkel") replacing this one.
• “extras/LiftMedia Setup”: This folder contains the Windows installer for the LiftMedia Designer
software.
• “extras/Sample Project”: This folder contains the default LiftMedia Designer project currently
loaded in the SD-Card.
07/2010 13 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
Before starting to create a project with LiftMedia Designer, it will be helpful to watch
the tutorial videos in English voice that can be found at www.arkel.com.tr website. In
theses tutorial videos, design creation and compilation with LiftMedia Designer is
demonstrated.
In addition you can also download the following files from www.arkel.com.tr before starting the design:
• Sample projects: Sample projects for horizontal and vertical installation.
• Sound library: Floor arrival and lift event announcements (in English)
• Picture library: Lift event pictures (in English)
Legal Notice
The LiftMedia sound and picture libraries are remain the property of Arkel Elektrik Elektronik Tic. Ltd. Sti.
These are provided for the use of with the LiftMedia and may not be used for any other purposes.
Please remember to observe copyright laws and regulations. Ensure that you use copyrighted materials
(video, music, speech and picture files). ARKEL is not responsible for any file used in the LiftMedia except
the files in the sample design folder.
07/2010 14 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
1 2 3 4
5
6
7 10
8 9
1- Project: With this menu tab, you can open new project, open an existing project, save and compile
your project.
2- Mode: Screen and sound designer mode selection tab.
3- Settings: Backlight turn-off and sound volume settings.
4- Language: Language selection tab (Turkish and English).
5- New: With this button, you can open a new blank project.
6- Open…: With this button, you can open any LiftMedia project in your PC or computer.
7- Save…: With this button, you can save your project.
8- Screen designer: With this button, you can organize the LiftMedia screen.
9- Sound designer: With this button, you can organize the sounds for your LiftMedia design.
10- Compile project: With this button, you can compile your saved project.
07/2010 15 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
10
1 2
3
7
4
6
5
8
07/2010 16 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
1
3
5
1- Playlist: You can add music and video files using this tab.
2- Floor arrival announcements: To announce the floor arrivals, any sound can be added to this area.
If more than one sound is added to the same line (“Sound-1”, “Sound-2” and “Sound-3”) the sounds
will be announced consecutively.
3- Other announcements: To announce the “out of service”, “overload” etc. alerts, designated sounds
could be added to this area.
4- Added videos, sounds and announces could be previewed in this area.
5- Any video, announce and sound data could be searched in your pc or laptop by this area.
07/2010 17 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
When you click the Settings tab, “General Settings” menu will appear.
07/2010 18 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
After the project design is completed, the project should be saved and then compiled. Only then the created
design will be ready to be transferred to LiftMedia.
To save the project click the button in the menu bar. A window appears like shown below:
Then to compile the project click the button in the menu bar. A window appears like shown below.
The compilation time of the project depends on the number and size of the files added to the project.
During the compilation process, picture, audio and video files in the project are converted to file formats that
LiftMedia can run.
After compilation process is completed, a folder named “arkel” will be created in the folder where the
project is saved. Copy this created folder replacing the folder named “arkel” in the SD-card. The folder name
must be “arkel”. A folder with a different name is not recognized by LiftMedia.
Note: Consider the capacity of the SD-Card before copying the "arkel" folder to SD-card. If the folder size is
more than the SD-card capacity, remove files as needed from the project and compile it again.
07/2010 19 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
• Learn the firmware version currently running in the LiftMedia. For this, follow the steps below:
Initializing SDCard…
SDCard not detected. Insert card…
Version on SDCard: 100707 Firmware version
10 07 07
Figure-8
• Download the “LiftMedia Firmware File” file from www.arkel.com.tr website. The right six number
of the .zip file name is the firmware version. If this version is newer than the device’s version than
an update is recommended
• Copy the “liftmdia.afw” firmware file inside this .zip file to “arkel/liftmdia” folder in SD-card
• During start-up, LiftMedia will find the new firmware and will update its firmware.
07/2010 20 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
12.1. LiftMedia-P
(Ø)
Figure-9
A: 3,5 K: 109,0
B: 7,0 L: 115,2
C: 18,3 M: 123,0
U
D: 33,3 R: 167,8
Figure-10 E: 44,0 S: 181,8
G: 73,4 T: 4,0
I: 86,4 U: 34,0
Note: All dimensions in mm
07/2010 21 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
12.2. LiftMedia-S
(Ø)
Figure-11
A: 3,5 H: 75,0 O: 133,7
B: 7,0 I: 86,4 P: 152,0
C: 18,3 J: 101,0 R: 167,8
U D: 33,3 K: 109,0 S: 181,8
E: 44,0 L: 115,2 T: 4,0
Figure-12 F: 67,0 M: 123,0 U: 28,0
G: 73,4 N: 125,7
Note: All dimensions in mm
12.3. Loudspeaker
F
E A: 75 E: 5
B: 40 F: 7
B D
C: 90 G: 35
D: 52
Note: All dimensions in mm
A G
C
Figure-13
07/2010 22 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
13. Troubleshooting
Problem Images appear on the screen but the floor indicator or up/down arrows do not appear
a) For LiftMedia-P: The operating mode should be selected using the menu buttons (see chapter
4.2. Time, Date and Input Mode Settings for LiftMedia-P)
Possible Also ensure that the connection is correct, terminals GCOM and ICOM should be connected
solution to +24Vdc or 0V (see chapter 3.1.2. Liftmedia-P Electrical Connections)
b) For LiftMedia-S: These information is taken from CANbus serial interface. Check CANbus
connection.
Problem LiftMedia works but after a while backlight turns off and the screen gets black
If you selected one of the options for turning off the backlight with car light in the “Settings”
menu of LiftMedia Designer tool:
a) For LiftMedia-P: You must connect the car light output to input I1.
Possible b) For LiftMedia-S: The car light status information is taken from CANbus serial interface
solution and the backlight is turned-off after car-light with the adjusted delay.
If you do not want to use this feature, select “never” option in the “Settings” menu in your
project and recompile the project. Please note that selecting this option will significantly reduce
the lifetime of your screen.
07/2010 23 L iftMedia
ARKEL Elektrik Elektronik Ltd. Şti. www.arkel.com.tr
07/2010 24 L iftMedia