Professional Documents
Culture Documents
Heat Transfer of Double Pipe Heat Exchanger Performance by Using Nanofluids and Serrated Fins
Heat Transfer of Double Pipe Heat Exchanger Performance by Using Nanofluids and Serrated Fins
net/publication/338646532
CITATIONS READS
0 15
3 authors, including:
Some of the authors of this publication are also working on these related projects:
CFD Study to Enhance the Heat Transfer in Heat Exchanger by Change the Outer Surface of the Inner Tube and Use Nano Fluid View project
Experimental study o Free Convection Inside Curvy Surfaces Porous Cavity View project
All content following this page was uploaded by Zena K. Kadhim on 04 December 2020.
Abstract
Annular serrated finned-tubes are well established in many thermal systems. This paper presents the results of
numerical calculations which carried out for the performance improvement of these devices. This study deals the main
investigations conducted with different five mass flow rate between (0.012, 0.14,0.016,0.018 and 0.02) kg/sec for the
cooled water and selected one mass flow rate for the hot water with (Re, 250), as well as the effect of the number of fin
segments of serrated fins (4, 8, 10, 12 and 14), and the effect of fin twisting of the outermost part of the fin on the
performance of the serrated finned-tubes. The twisting angles considered are between β (0o and 25o ) where a comparison
between performances of finned tubes with and without fin serration, the computational results showed that the Nusselt
number with serrated insert is augmented by (61.9, 53. 41, 27.8, and 12.6%) fo r (14, 12,10,8 and 4) serrated fins
respectively comparing with smooth tube. The maximum value of Nusselt number and maximal skin friction coefficient
was found in 14 serrated fins.
1. Introduction
Annular notched finned-tubes are well recognized in many thermal systems by many projects. The reduce the sources
of primary energy in order to improve heat exchangers efficiency can also contribute to reduce the production of CO2.
for example, "Steam boilers or heat recovery boilers, is inherently lower than the heat transfer coefficient on the inside
of the water tubes" (Hofmann, rasz, & Ponweiser, 2007, 1). However, many types are used to improve heat transfer on
(air or water) such as the heat-transferring surface and finned tubes with segmented fins (Frass, Hofmann, & Ponweiser,
2007).
Moreover, the tubes staggered arrangement in bundle can higher turbulence which can also increase the pressure drop
of resistance in flow channel as well as the turbulence. According to Hofmann, et al., (2007) many studies found that
"Optimizing a finned tube heat exchanger also results in minimizing the pumping power" (Carranza & Ospina, 2006;
Naess, 2005; Halici, & Taymaz, 2006). There are seven different segmented in finned arrangements of tube bundle
thus, in order to compared it with solid fins. Therefore, it can find height of segmented fins which could be greater than
the maximum fin height because fins to weld by laser. Therefore, it can enhance the total area of outside surface and
also result of efficiency of heat exchanger.
However, in the research article the performance in various finned tubes which forced convection were evaluated.
Moreover, this study was investigated three different kinds of finned tubes. These three types find where the fin height
varies most. Additionally, the effect of geometry by pressure drop properties and heat transfer were associated by “solid
and serrated Ishaped fins and serrated U-shaped fins”. In specific, the important effect of fin height in this research has
been considered. Finally, the similarity to the “generalized Lévêque equation” for heat transfer in tube associations
have been applied thus, the maximum value of “Nusselt number and maximal skin friction coefficient” ha s been found
in 14 serrated fins.
77
2. Simulation Model
The present study, a numerical examination of heat transfer enhancement in individual annular serrated fins double
tube heat exchanger is carried out. Double tube heat exchangers consisted of annuli PVC tube of (76.2 mm) outer
diameter, (3 mm) thickness, and (1000mm), and the straight copper tube with outer diameter of (14.87mm), (1mm)
thickness, and a length of (1000 mm). Fourteen individual annular serrated fins with a different number of fin segments
of serrated fins (4, 8, 10, 12 and 14) are fixed perfectly on the external surface of copper tube, axial distance between
Individual annular serrated fins (S, 61𝑚𝑚). Cold water at various mass flow rates (0.12 to 0.2) kg/sec flows through
annuli and hot water at Reynold's numbers (250) flows through the inner tube. A schematic diagram of the serrated
finned tube with serrated finned inserts is shown in Figure (1).
Fig. (1) Serrated finned tube and number of fin segments of annular serrated fins
(4, 8, 10, 12 and 14)
78
3. Boundary Conditions
In order to estimate the current heat exchangers performance in recent research, some of the physical requirements of
the sample are sufficiently determined as follows:
4. Governing equations
𝜕𝑢 𝜕𝑢 𝜕𝑢 𝜕𝑃 𝜕 2𝑢 𝜕2 𝑢 𝜕 2𝑢
𝜌 (𝑢 +𝑣 +𝑤 )=− +𝜇( + + ) (2)
𝜕𝑥 𝜕𝑦 𝜕𝑧 𝜕𝑥 𝜕𝑥2 𝜕𝑦 2 𝜕𝑧2
𝜕𝑣 𝜕𝑣 𝜕𝑣 𝜕𝑃 𝜕2 𝑣 𝜕2 𝑣 𝜕 2𝑣
𝜌 (𝑢 +𝑣 +𝑤 )=− +𝜇( + + ) (3)
𝜕𝑥 𝜕𝑦 𝜕𝑧 𝜕𝑦 𝜕𝑥2 𝜕𝑦 2 𝜕𝑧2
𝜕𝑤 𝜕𝑤 𝜕𝑤 𝜕𝑃 𝜕 2𝑤 𝜕 2𝑤 𝜕 2𝑤
𝜌 (𝑢 +𝑣 +𝑤 )=− +𝜇( + + ) (4)
𝜕𝑥 𝜕𝑦 𝜕𝑧 𝜕𝑧 𝜕𝑥2 𝜕𝑦 2 𝜕𝑧 2
Energy equation
𝜕𝑇 𝜕𝑇 𝜕𝑇 𝜕2 𝑇 𝜕 2𝑇 𝜕 2𝑇
𝜌𝐶𝑝 (𝑢 +𝑣 +𝑤 )= 𝑘( + + ) (5)
𝜕𝑥 𝜕𝑦 𝜕𝑧 𝜕𝑥2 𝜕𝑦 2 𝜕𝑧2
All equations that govern with the boundary conditions have been applied using Fluent 18 software, which is based
on a limited size method, which are based on the limited volume technique. A simple algorithm was used for join the
compression velocity, after that the second-degree reverse-wind scheme was applying to the abstract in terms of
convection.
79
4.2 Mesh Generation
Therefore, to achieve the correctness of numerical simulation in this research study. There are different network
strategies have been employed in simulation. Complex geometry, generating such a network is a waste of time that
always requires modifications to the engineering model. There are mainly two kinds of approaches in volume meshing.
These are structured and unstructured meshing shown in figure (2). In structured mesh, the main equations have been
transformed to the curvilinear coordinate system aligned with the surface and It also is small for simple figures.
However, it becomes extremely inefficient and waste time for composite geometries. Therefore, it was excluded in
current research. In the unstructured approach, the integral form of governing equations is discretized and either a finite-
volume or a finite-element scheme is used. Unstructured networks are in general successful for complex geometries,
such as the result that was used in the pres ent study. For the present work, the number of cells generated are shown in
Table (1).
(a)
(b)
80
5. RESULTS AND DISCUSSION
9
Nu ave
m (Kg/s)
Figure 3. Nusselt number versus mass flow rate base on different fins number (0, 4, 8, 10, 12, and
14).
The effect of serrated fins on the skin friction coefficient in circular pipe is illustrated in Figure (4). As expected,
the skin friction coefficient decreases with the rise of mass flow rate at all serrated fins because the skin friction
coefficient is inversely relative with the fluid velocity. It is also evident that the skin friction coefficient increases with
the increase of the serrated fins and has a maximum value at the (14) of serrated fins. It is attributed to the increasing
the serrated fin helps to generate longer flow path close to the serrated fins and resulted largest flow blockage.
Moreover, when the numbers of serrated fins increase it changes the velocity profile and causes an increase in the
resistance to the main flow resulting increase of skin friction coefficient.
81
0.00225
14 FINS
12 FINS
10 FINS
8 FINS
0.0021 4 FINS
0 FINS
0.0018
0.00165
0.0015
0.00135
0.012 0.014
. 0.016 0.018 0.02
m (Kg/s)
Figure 4. Skin friction coefficient vs mass flow rate at versus number of serrated fins, (0, 4, 8,
10, 12, and 14).
Where, Nu is the Nusselt number of the improved tube and Nu o is the Nusselt number for the smooth tube, while
ƒ and ƒo are the skin friction coefficient of the improved tube and smooth tube, respectively. Gaining larger value of
the performance evaluation criteria means the excellent total performance. Therefore, the performance evaluation
criteria (PEC > 1) intends that heat transfer enhancement is greater than the raise in the pressure drop penalty Namburu
et al (2002), have obtained a value of the ratio (P.E.C>1). Figure 5 depicts all the data in order to compare the effect of
varied number of serrated fins on the performance evaluation criteria (PEC). From this figure, it is clearly seen that the
excellent rate of the performance evaluation criteria (PEC) may be obtain whe n utilize 14 serrated fins with small rate
of mass flow. Additionally, it is noted that the performance evaluation criteria (PEC) decreases with increasing of mass
flow rate. Therefore, this method may have a better improvement effect with a comparatively lesser flow resistance. In
other words, it is expected to be able to achieve a higher PEC magnitude. In the current work, the thermal performance
and flow resistance characteristics of laminar flow with the serrated fins placed on the wall of a circular tu be through
numerical simulation were studied.
82
2.6
14 FINS
12 FINS
2.4 10 FINS
8 FINS
4 FINS
2.2
PEC
1.8
1.6
1.4
1.2
Figure 5. Variation of the PEC with different mass flow rate at different serrated fins, (0, 4, 8,
10, 12, and 14).
The flow visualization in term of 2D streamlines for the water in the case of mass flow rate (0.02 Kg/s) for varied
number of serrated fins are present in Figure 6. It is clearly seen that the increase of the number of serrated fins causes
circulations behind the tips of serrated fin. Circulations in helical swirls s hapes lead eddies to enter deep in the boundary
layer. This behavior of swirls makes the boundary layer thinner. Accordingly, eddies can force the cold fluid in the
outer tube toward to the wall of the concentrations tube and force the hot fluid near the wall of the concentrations tube
toward to the cold fluid flow direction of the outer tube causes increasing the mixing of the flow.
This mixing of flow improves the heat removal. The greater mixing flow and swirl was found with serrated fins
14 and the flow was found weak at serrated fins, 4 because of the flow becomes less disturbed and resulting much weak
convective current and limited effect on the heat transfer rate.
83
“a”
“b”
“c”
84
“d”
“e”
Figure 6. Velocity at mass flow rate 0.02 Kg/s, S, 61mm, serrated fins [a-4, b-8, c-10, d-12 and
without serrated fins].
Moreover, the case with symmetric serrated fins gives a higher Nusselt number comparing with the case of reverse
serrated. It is attributed to the increasing in the resistance to the main flow, which forces the flow to run far of the pipe
wall resulting decrease of temperature gradients. It is also evident that the skin friction coefficien t at the 14 of reverse
serrated fins is higher than the case with the 14 symmetric serrate fins. It is attributed that the reverse serrated fins result
85
largest flow blockage. Moreover, the reverse of serrated fins changes the velocity profile and causes an increase in the
resistance to the main flow resulting increase of skin friction coefficient.
11.5
o
14 fins at angle=13
o
11 14 fins at angle=0
10.5
10
Nuave
9.5
8.5
7.5
.
m (Kg/s)
Figure 7. Nusselt number vs mass flow rate at reverse serrated fins and the symmetric serrate
fins.
0.00225
o
0.0022 14 fins at angle=13
o
14 fins at angle=0
0.00215
0.0021
skin friction coefficient
0.00205
0.002
0.00195
0.0019
0.00185
0.0018
0.00175
0.0017
0.00165
0.0016
Figure 8. Skin friction coefficient vs mass flow rate at reverse serrated fins and the symmetric
serrate fins.
6. Conclusions
Serrated fins in circular pipe heat exchanger were used in order to improve the heat transfer convection of laminar in
the tube. Three achievements have been gotten in this research from numerical simulation. These are Nusselt number,
skin friction coefficient, and (PEC). Therefore, the following points have been concluded which can be summarized
as: The average Nusselt number and the heat transfer enhancement for all serrated fins increased with increase of mass
flow rate. A dramatic enhancement in Nusselt number obtained by using serrated fins of vortex generator and base fluid
compared to the plane tube. The maximum skin friction coefficient was found by using the 14 fins of serrated. Because
the larger flow, resistance with using serrated fins was found at the 14 fins. The maximal value of the (PEC) was found
in the case of the 14 fins of serrated and the pitch distance of (S, 61mm). Finally, more research should be studied base
on this area in order to find better result.
86
References
K. Hashizume et al, Fin efficiency of serrated fins, Heat Transfer Engineering, Vol.23, 2002, pp. 6-14.
Hofmann, R., Frasz, F., & Ponweiser, K. (2007). Heat transfer and pressure drop performance comparison of finned -
tube bundles in forced convection. WSEAS Trans. Heat Mass Transfer, 2(4), 72-88.
Frass, F., Hofmann, R., & Ponweiser, K. (2007). Principles of finned-tube heat exchanger design for enhanced heat
transfer. Inst. f. Thermodynamics and Energy Conversion, Vienna University of Technology.
Carranza, R. G., & Ospina, J. (2006). Fin efficiency of a three sided pyramidal fin of equilateral triangular and variable
cross-sectional area: analytical solution. WSEAS Transactions on Heat and Mass Transfer, 1(3), 337.
Naess, E. (2005). Heat transfer and pressure drop in serrated-fin tube bundles for waste heat recovery applications.
In 6th world conference on experimental heat transfer, fluid mechanic, and th ermo-dynamics, Japan, vol No (pp.
1-5).
Halici, F., & Taymaz, I. (2006). Experimental study of the airside performance of tube row spacing in finned tube heat
exchangers. Heat and mass transfer, 42(9), 817-822.
Kleinstreuer, C., (2010). Modern Fluid Dynamics, Basic Theory and Selected Applications in Macro - and Micro-
Fluidics. Springer Dordrecht Heidelberg London New York
Ahmed, H. E., & Yusoff, M. Z. (2018). Thermal enhancement of triangular ducts using compound of vortex generators
and nanofluids. Heat Transfer Engineering, 39(5), 422-435.
Manca, O., Nardini, S., Ricci, D. (2012). A Numerical Study of Nanofluid Forced Convection in Ribbed Channels.
Appl. Therm. Eng., 37, 280-292.
87