Professional Documents
Culture Documents
Re92711 2012-01 A10vso
Re92711 2012-01 A10vso
12
Replaces: 06.09
1/48
and RE 92707/11.10
A10VSO
Data sheet
Series 31
Sizes 18 to 140
Nominal pressure 280 bar
Maximum pressure 350 bar
Open circuit
Contents Features
Type code for standard program 2 –– Variable pump in axial piston swashplate design for hydro
static drives in an open circuit
Technical data 4
–– The flow is proportional to the drive speed and the displace
Technical data, standard unit 6
ment
Technical data, high-speed version 7
–– The flow can be steplessly varied by adjustment of the
DG – Two-point control, directly operated 10 swashplate angle.
DR – Pressure control 11 –– 2 case drain ports
DRG – Pressure control, remotely operated 12 –– Excellent suction characteristics
DFR, DFR1 – Pressure and flow control 13 –– Low noise level
DFLR – Pressure, flow and power control 14 –– Long service life
ED – Electro-hydraulic pressure control 15 –– Axial and radial load capacity of drive shaft
ER – Electro-hydraulic pressure control 16 –– Favorable power/weight ratio
Dimensions sizes 18 to 140 18 –– Versatile controller range
Dimensions through drive 36 –– Short control time
Summary mounting options 41 –– The through drive is suitable for adding gear pumps and axial
piston pumps up to the same size, i.e., 100% through drive.
Combination pumps A10VO + A10VO 42
Connector for solenoids 44
Installation instructions 46
General instructions 48
2/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
Operation mode
03 Pump, open circuit O
Size (NG)
04 Geometric displacement, see table of values on pages 6 and 7 18 28 45 71 100 140
Control device
Two-point control, directly operated l l l l l l DG
Pressure control l l l l l l DR
with flow control, hydraulic
Series
06 Series 3, Index 1 31
Direction of rotation
Viewed on drive shaft clockwise R
07
counter clockwise L
Seals
08 FKM (fluor-caoutchouc) V
1) See RE 30030
2) The following must be taken into account during project planning:
Excessive current levels (I > 1200 mA with 12 V or I > 600 mA with 24 V) to the ER solenoid can result in undesired increase
of pressure which can lead to pump or system damage:
- Use Imax current limiter solenoids.
- A sandwich plate pressure reducing valve can be used to protect the pump in the event of overflow.
An accessory kit with pressure reducing sandwich plate can be ordered from Rexroth under part number R902490825.
Technical data
Hydraulic fluid Notes on the choice of hydraulic fluid
Before starting project planning, please refer to our data In order to select the correct hydraulic fluid, it is necessary to
sheets RE 90220 (mineral oil) and RE 90221 (environmentally know the operating temperature in the reservoir (open circuit)
acceptable hydraulic fluids) for detailed information regarding in relation to the ambient temperature.
the choice of hydraulic fluid and application conditions.
The hydraulic fluid should be selected so that within the operat
When using environmentally acceptable hydraulic fluids, ing temperature range, the viscosity lies within the optimum
the limitations regarding technical data and seals must be range (nopt), see shaded section of the selection diagram. We
observed. Please contact us. When ordering, indicate the recommend to select the higher viscosity grade in each case.
hydraulic fluid that is to be used.
Example: at an ambient temperature of X °C the operating
Operating viscosity range temperature is 60 °C. In the optimum operating viscosity range
(nopt; shaded area) this corresponds to viscosity grades VG 46
For optimum efficiency and service life we recommend that the
resp. VG 68; VG 68 should be selected.
operating viscosity (at operating temperature) be selected in
the range Important:
nopt = opt. operating viscosity 16 ... 36 mm /s 2 The case drain temperature is influenced by pressure and input
speed and is always higher than the reservoir temperature.
referred to reservoir temperature (open circuit). However, at no point in the component may the temperature
Limits of viscosity range exceed 90 °C. The temperature difference specified on the left
is to be taken into account when determining the viscosity in
For critical operating conditions the following values apply: the bearing.
nmin = 10 mm2/s If the above conditions cannot be met, due to extreme operat
short-term (t ≤ 1 min) ing parameters please contact us.
at max perm. case drain temperature of 90 °C.
Filtration of the hydraulic fluid
Please also ensure that the max. case drain temperature of The finer the filtration the better the cleanliness level of the
90 °C is not exceeded in localized areas (for instance, in the hydraulic fluid and the longer the service life of the axial piston
bearing area).The fluid temperature in the bearing area is unit.
approx. 5 K higher than the average case drain temperature.
In order to guarantee the functional reliability of the axial piston
nmax = 1000 mm2/s unit it is necessary to carry out a gravimetric evaluation of the
short-term (t ≤ 1 min) hydraulic fluid to determine the particle contamination and the
on cold start cleanliness level according to ISO 4406. A cleanliness level of
(p ≤ 30 bar, n ≤ 1000 rpm, tmin -25 °C) at least 20/18/15 must be maintained.
Depending on the installation situation, special measures At very high hydraulic fluid temperatures (90 °C to maximum
are necessary at temperatures between -40 °C and -25 °C. 115 °C), a cleanliness level of at least 19/17/14 according to
Please contact us. ISO 4406 is necessary.
For detailed information on operation with low temperatures If the above cleanliness levels cannot be maintained, please
see data sheet RE 90300-03-B. contact us.
Selection diagram
VG 32
VG 46
VG 2
10
2
100
0
Viscosity n [mm2/s]
60
40 36
nopt.
20
16
10
5 5
-40 -25 -10 0 10 30 50 70 90 115
Temperature t in °C
tmin = -40 °C Fluid temperature range tmax = +115 °C
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 5/48
Technical data
Operating pressure range
Note
Please contact us for values for other hydraulic fluids.
Note
Exceeding the maximum or falling below the minimum permissible values can lead to a loss of function, a reduction in operational
service life or total destruction of the axial piston unit. We recommend to check the loading through tests or calculation / simula
tion and comparison with the permissible values.
Determination of size
Note
Exceeding the maximum or falling below the minimum permissible values can lead to a loss of function, a reduction in operational
service life or total destruction of the axial piston unit. We recommend to check the loading through tests or calculation / simula
tion and comparison with the permissible values.
Sizes 45, 71, 100 and 140 are optionally available in high-speed version.
External dimensions are not affected by this option.
8/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
Technical data
Permissible radial and axial loading on the drive shaft
Size NG 18 28 45 71 100 140
Radial force maximum Fq
at a/2
Fq max N 350 1200 1500 1900 2300 2800
a/2 a/2
a
T1 T2
TE
1. Pumpe
1st pump 2.
2ndPumpe
pump
TD
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 9/48
Technical data
Drive power and flow
Operating material:
Hydraulic fluid ISO VG 46 DIN 51519, t = 50 °C
Size 18 Size 71
_ _ _ _ n = 1500 rpm _ _ _ _ n = 1500 rpm
______ n = 3300 rpm ______ n = 2200 rpm
160 80
60 30 140 qv 70
Flow qV [l/min]
Flow qV [l/min]
40 20 120 60
Size 28 0 0
0 50 100 150 200 250 280
_ _ _ _ n = 1500 rpm Operating pressure [bar]
______ n = 3000 rpm
Size 100
90 _ _ _ _ n = 1500 rpm
80 40
Flow qV [l/min]
80 40
qv
60 30 Size 140
Pqv max
40 20 _ _ _ _ n = 1500 rpm
20 10
______ n = 1800 rpm
0 Pqv zero 0
0 50 100 150 200 250 280 260 130
140 70
120 60
100 50
80 40
60 Pqv zero 30
40 20
20 10
0 0
0 50 100 150 200 250 280
Operating pressure [bar]
10/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
120
100
Req. control pressure pst [bar]
50 L1 S
Port for
0 50 70 140 210 280 B Service line
Operating pressure pB [bar] S Suction line
L, L1 Case drain (L1 plugged)
X Pilot pressure
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 11/48
DR – Pressure control
The pressure control limits the maximum pressure at the pump Circuit diagram, sizes 18 to 100
output within the pump control range. The variable pump only
supplies as much hydraulic fluid as is required by the consum
ers. If the operating pressure exceeds the pressure setpoint set
at the integrated pressure valve, the pump will adjust towards a
smaller displacement and the control deviation will be reduced. L B
The pressure can be set steplessly at the control valve.
Static characteristic
(at n1 = 1500 rpm; tfluid = 50 °C)
L1 S
25
Flow qv [l/min]
Control data
Hysteresis and repeatability ∆p______________ maximum 3 bar
Pressure rise, maximum
NG 18 28 45 71 100 140
∆p bar 4 4 6 8 10 12
Control fluid consumption___________ maximum approx. 3 l/min
Flow losses at qVmax see page 9.
12/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
Static characteristic
(at n1 = 1500 rpm; tfluid = 50 °C)
Hysteresis / pressure rise ∆pmax
L1 S
280
Circuit diagram, size 140
Operating pressure pB [bar]
20
Control data
Hysteresis and repeatability ∆p______________ maximum 3 bar
Pressure rise, maximum
NG 18 28 45 71 100 140
∆p bar 4 4 6 8 10 12
Control fluid consumption_________ maximum approx. 4.5 l/min
Flow losses at qVmax see page 9.
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 13/48
280
Operating pressure pB [bar]
Setting range1)
L1 S
25
Circuit diagram, size 140
Port for
B Service line
S Suction line
Flow qv [l/min]
300
280 Maximum
power curve X
250 Not included
Operating pressure pB [bar]
in the delivery
contents
200
150
100 L B
Maximum
50 power curve
∆qV
(see table L1 S
on page 13)
X
Not included
in the delivery
contents
0 100
Volume flow qv [%]
L B
Control data
Beginning of control_ _____________________________ 50 bar
Control fluid consumption________ maximum approx. 5.5 l/min
Flow loss at qv max, see page 9.
Port for
B Service line
S Suction line
L, L1 Case drain (L1 plugged) L1 S
X Pilot pressure
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 15/48
Standby [bar]
This causes an increase or decrease in the pump swivel angle 24
(flow) in order to maintain the electrically set pressure level. 22
ED
of control B
Max. adjustable
control pressure
140
L1 S
Hysteresis of the static current-pressure characteristic < 3 bar
Port for
Static flow-pressure characteristic B Service line
(at n= 1500 rpm; tfluid = 50 °C) S Suction line
L, L1 Case drain (L1 plugged)
max
280
Hysteresis / pressure rise ∆p
Operating pressure p [bar]
Setting range
250
Max. adjustable L1 S
control pressure
150
Port for
Min.
50 adjustable B Service line
control pressure S Suction line
0
0 1
Amperage L, L1 Case drain (L1 plugged)
I/Imax
Notes
18/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
V
Valve mounting for
ccw rotation
6.3 108 B
83
max. 110
Flange L X L
11
ISO 3019-2
X
45° 45°
63
40
Ø80 -0.046
66
0
63
64
69
11.5 109
L1 152
43 S
145 109
195 126
View V View W
22.2
B S
52.4
Ø25
47.6
Ø20
26.2
Ports
Designation Port for Standard Size1) Maximum State
pressure [bar]2)
B Service line, SAE J5183) 3/4 in 350 O
fastening thread DIN 13 M10 x 1.5; 17 deep
S Suction line, SAE J5183) 1 in 10 O
fastening thread DIN 13 M10 x 1.5; 17 deep
L Case drain fluid DIN 38524) M16 x 1.5; 12 deep 2 O5)
L1 Case drain fluid DIN 38524) M16 x 1.5; 12 deep 2 X5)
X Pilot pressure DIN 38524) M14 x 1.5; 12 deep 350 O
X Pilot pressure with DG-control DIN ISO 2284) G 1/4 in 350 O
1) For the maximum tightening torques the general instructions on page 48 must be observed
2) Depending on the application, short-term pressure spikes can occur. Keep this in mind when selecting measuring equipment
and fittings. Pressure values in bar absolute.
3) Only dimensions according to SAE J518, metric fastening thread deviating from the standard
4) The spot face can be deeper than as specified in the standard
5) Depending on the installation position, L or L1 must be connected (see also installation instructions on pages 44, 45)
O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 19/48
Drive shaft
S Splined shaft 3/4 in R Splined shaft 3/4 in P Parallel shaft key
11T 16/32DP1) (SAE J744) 11T 16/32DP1)2) (SAE J744) DIN 6885, A6x6x25
30 28
+ 0.3
1/4-20UNC-2B3) 4)
0
1/4-20UNC-2B3) 4)
0.008
ø18 +- 0.003
14
14
2 25
5 5
ø22 - 0.033
20.5 -0.1
0
Usable shaft 21 Centering5)
21 length R 3.15 x 6.7
38 DIN 332 36
38
1) ANSI B92.1a, 30° pressure angle, flat root, side fit, tolerance class 5
2) Splines according to ANSI B92.1a, run out of spline is a deviation from standard
3) Thread according to ASME B1.1
4) For the maximum tightening torques the general instructions on page 48 must be observed
5) Coupling axially secured, e.g. with a clamp coupling or radially mounted clamping screw
20/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
DG DR
Two-point control, directly operated Pressure control
to flange surface
max. 110
X
X
+0.4
3
G 1/4 in
25
12
89 126
97
to flange surface
175.4
to flange surface
Valve mounting for
108 Valve mounting for
ccw rotation
140
ccw rotation
X
max. 110
X
X
40
109
126 1261)
max. 110
14
45°
45°
X
80
-0.054
40
74
0
Ø100
Ø1
74
80
74
14 140
40 L1 S 164
164
206 83.5 119.3
136
W
Detail V Detail W
22.2
Ø20
58.7 S
Ø32
47.6
B
30.2
Ports
Designation Port for Standard Size1) Maximum State
pressure [bar]2)
B Service line, SAE J5183) 3/4 in 350 O
fastening thread DIN 13 M10 x 1.5; 17 deep
S Suction line, SAE J5183) 1 1/4 in 10 O
fastening thread DIN 13 M10 x 1.5; 17 deep
L Case drain fluid DIN 38524) M18 x 1.5; 12 deep 2 O5)
L1 Case drain fluid DIN 38524) M18 x 1.5; 12 deep 2 X5)
X Pilot pressure DIN 38524) M14 x 1.5; 12 deep 350 O
X Pilot pressure with DG-control DIN ISO 2284) G 1/4in; 12 deep 350 O
1) For the maximum tightening torques the general instructions on page 48 must be observed.
2) Depending on the application, short-term pressure spikes can occur. Consider this when selecting measuring equipment and
fittings. Pressure values in bar absolute.
3) Only dimensions according to SAE J518, metric fastening thread deviating from the standard.
4) The spot face can be deeper than as specified in the standard.
5) Depending on the installation position, L or L1 must be connected (see also installation instructions on pages 44, 45)
O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
22/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
Drive shaft
S Splined shaft 7/8 in R Splined shaft 7/8 in P Parallel shaft key
13T 16/32DP1) (SAE J744) 13T 16/32DP1)2) (SAE J744) DIN 6885, A6x6x32
36 + 0.3
0.0
33.1 32
1/4-20UNC-2B3) 5)
1/4-20UNC-2B3) 5)
16
16 16
5 2
5
M64), 5)
24.4 -0.2
ø22 +0.009
-0.004
Usable shaft 25
25.1 length
41 46
41
1) ANSI B92.1a, 30° pressure angle, flat root, side fit, tolerance class 5
2) Spline according to ANSI B92.1a, run out of spline is a deviation from standard.
3) Thread according to ASME B1.1
4) Thread according to DIN 13
5) For the maximum tightening torques the general instructions on page 48 must be observed.
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 23/48
DG DFLR
Two-point control, directly operated Pressure, flow and power control
max. 110
G 1/4 in
X
L
40
3
25 +0.4
X
12
99.5 119
103.5 135.5
DR DRG
Pressure control Pressure control, remotely operated
to flange surface
max. 110
max. 110
X
X
40
119
136 136
ED7. / ER7.
Electro-hydraulic pressure control
to flange surface
135.51)
V
9.5 133
6.3 96
83
Flange L X
14 L
ISO 3019-2
max. 110
45°
45°
X
90
Ø100 -0.054
40
0
80.5
14.3 L1 90
Ø140
45
184 Ø184
219 93.5 129
224 146
Detail V View W
26.2
B
S
69.9
52.4
Ø40
Ø25
35.7
Ports
Designation Port for Standard Size1) Maximum State
pressure [bar]2)
B Service line, SAE J5183) 1 in 350 O
fastening thread DIN 13 M10 x 1.5; 17 deep
S Suction line, SAE J5183) 1 1/2 in 10 O
fastening thread DIN 13 M12 x 1.75; 20 deep
L Case drain fluid DIN 38524) M22 x 1.5; 14 deep 2 O5)
L1 Case drain fluid DIN 38524) M22 x 1.5; 14 deep 2 X5)
X Pilot pressure DIN 38524) M14 x 1.5; 12 deep 350 O
X Pilot pressure with DG-control DIN ISO 2284) G 1/4 in 350 O
1) For the maximum tightening torques the general instructions on page 48 must be observed.
2) Depending on the application, short-term pressure spikes can occur. Consider this when selecting measuring equipment and
fittings. Pressure values in bar absolute.
3) Only dimensions according to SAE J518, metric fastening thread deviating from the standard.
4) The spot face can be deeper than as specified in the standard.
5) Depending on the installation position, L or L1 must be connected (see also installation instructions on pages 44, 46)
O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 25/48
Drive shaft
S Splined shaft 1 in R Splined shaft 1 in P Parallel shaft key
15T 16/32DP1) (SAE J744) 15T 16/32DP1)2) (SAE J744) DIN 6885, A8x7x36
42 + 0.3
0.0
38 39
1/4-20UNC-2B3) 5)
1/4-20UNC-2B3) 5)
16
16 19
5 3
5
M84), 5)
ø25 +0.009
-0.004
28 -0.2
Usable shaft 29.5
30 length
45.9 52
45.9
1) ANSI B92.1a, 30° pressure angle, flat root, side fit, tolerance class 5
2) Spline according to ANSI B92.1a, run out of spline is a deviation from standard.
3) Thread according to ASME B1.1
4) Thread according to DIN 13
5) For the maximum tightening torques the general instructions on page 48 must be observed.
26/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
Dimensions
DG
size 45 DFLR
Before finalizing your design request a certi
fied installation drawing. Dimensions in mm.
to flange surface
Valve mounting for
to flange surface Valve mounting for 213 ccw rotation
173 ccw rotation
112
X
40
25 +0.4
3
G 1/4 in
12 129
110
146
117
DR DRG
Pressure control Pressure control, remotely operated
max. 110
max. 110
X
146 129 40
146
ED7. / ER7.
Electro-hydraulic pressure control
to flange surface
Valve mounting for
146
ccw rotation
140
L
X
145.51)
1) ER7.: 180.5 mm if using a sandwich plate pressure reducing valve.
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 27/48
12.7 161 V
6 115
18 98
Flange L
ISO 3019-2 X
max. 110
45°
L 45°
104
X
-0.063
40
0
Ø125
92
104
18 L1 180
53
210
217
107.5 143
257
160
Valve mounting for
W ccw rotation
Detail V Detail W
52.4
Ø25
26.2
Ø50
77.8
S
B
42.9
Ports
Designation Port for Standard Size1) Maximum State
pressure [bar]2)
B Service line, SAE J5183) 1 in 350 O
fastening thread DIN 13 M10 x 1.5; 17 deep
S Suction line, SAE J5183) 2 in 10 O
fastening thread DIN 13 M12 x 1.75; 20 deep
L Case drain fluid DIN 38524) M22 x 1.5; 14 deep 2 O5)
L1 Case drain fluid DIN 38524) M22 x 1.5; 14 deep 2 X5)
X Pilot pressure DIN 38524) M14 x 1.5; 12 deep 350 O
X Pilot pressure with DG-control DIN ISO 2284) G 1/4 in 350 O
1) For the maximum tightening torques the general instructions on page 48 must be observed.
2) Depending on the application, short-term pressure spikes can occur. Consider this when selecting measuring equipment and
fittings. Pressure values in bar absolute.
3) Only dimensions according to SAE J518, metric fastening thread deviating from the standard.
4) The spot face can be deeper than as specified in the standard.
5) Depending on the installation position, L or L1 must be connected (see also installation instructions on pages 44, 46)
O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
28/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
Drive shaft
S Splined shaft 1 1/4 in R Splined shaft 1 1/4 in P Parallel shaft key
14T 12/24DP1) (SAE J744) 14T 12/24DP1)2) (SAE J744) DIN 6885, A10x8x45
50
5/16-18UNC-2B3) 5)
5/16-18UNC-2B3) 5)
47.5
19 47.5
19
5 22
5
2.5
M104), 5)
+0.002
ø32+0.018
35 -0.2
Usable shaft 38
39.5 length
55.4
55.4 60
1) ANSI B92.1a, 30° pressure angle, flat root, side fit, tolerance class 5
2) Spline according to ANSI B92.1a, run out of spline is a deviation from standard.
3) Thread according to ASME B1.1
4) Thread according to DIN 13
5) For the maximum tightening torques the general instructions on page 48 must be observed.
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 29/48
DG DFLR
Two-point control, directly operated Pressure, flow and power control
to flange surface
to flange surface Valve mounting for
Valve mounting for 242 ccw rotation
201 ccw rotation
Ø25 +0.4
X
G 1/4in
124
L
X
40
3
12
123.5 143
127.5
159.5
DR DRG
Pressure control Pressure control, remotely operated
L
X
X
max 110
L
40
160
143
160
ED7. / ER7.
Electro-hydraulic pressure control
to flange surface
Valve mounting for
173 ccw rotation
140
L
X
1601)
6
ISO 3019-2
10
max. 110
L 45°
Ø125 -0.063
100
X
17.5
40
0
152
100
95
20 L1 180
95 210
275
118 148.4
317
164.9
329
Detail V Detail W
B
88.9
66.7
Ø60
Ø32
S
31.8 50.8
Ports
Designation Port for Standard Size1) Maximum State
pressure [bar]2)
B Service line, SAE J5183) 1 1/4 in 350 O
fastening thread DIN 13 M14 x 2; 19 deep
S Suction line, SAE J5183) 2 1/2 in 10 O
fastening thread DIN 13 M12 x 1.75; 17 deep
L Case drain fluid DIN 38524) M27 x 2; 16 deep 2 O5)
L1 Case drain fluid DIN 38524) M27 x 2; 16 deep 2 X5)
X Pilot pressure DIN 38524) M14 x 1.5; 12 deep 350 O
X Pilot pressure with DG-control DIN ISO 2284) G 1/4 in 350 O
1) For the maximum tightening torques the general instructions on page 48 must be observed.
2) Depending on the application, short-term pressure spikes can occur. Consider this when selecting measuring equipment and
fittings. Pressure values in bar absolute.
3) Only dimensions according to SAE J518, metric fastening thread deviating from the standard.
4) The spot face can be deeper than as specified in the standard.
5) Depending on the installation position, L or L1 must be connected (see also installation instructions on pages 44, 46)
O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 31/48
Drive shaft
S Splined shaft 1 1/2 in P Parallel shaft key
17T 12/24DP1) (SAE J744) DIN 6885, A12x8x68 66
7/16-14UNC-2B2) 4) 69.5
54
28
28 1.5
5
M123), 4)
ø40 -0.002
+0.018
43 -0.2
43.5
80
61.9
1) ANSI B92.1a, 30° pressure angle, flat root, side fit, tolerance class 5
2) Thread according to ASME B1.1
3) Thread according to DIN 13
4) For the maximum tightening torques the general instructions on page 48 must be observed.
32/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
DG DFLR
Two-point control, directly operated Pressure, flow and power control
129
25 +0.4
3
40
R 1/4in
12
128.5 164.5
132.5
DR DRG
Pressure control Pressure control, remotely operated
to flange surface
max. 110
X
148 40
165
165
ED7. / ER7.
Electro-hydraulic pressure control
to flange surface
1651)
126
110
26
Ø180 -0.063
158.4
5
0
200
8.
11
108
110
112
21 L1 158.4
78 200
275 131 183
337 209
Detail V Detail W
S
Ø32
88.9
66.7
Ø63
B
31.8 50.8
Ports
Designation Port for Standard Size1) Maximum State
pressure [bar]2)
B Service line, SAE J5183) 1 1/4 in 350 O
fastening thread DIN 13 M14 x 2; 19 deep
S Suction line, SAE J5183) 2 1/2 in 10 O
fastening thread DIN 13 M12 x 1.75; 17 deep
L Case drain fluid DIN 38524) M27 x 2; 16 deep 2 O5)
L1 Case drain fluid DIN 38524) M27 x 2; 16 deep 2 X5)
X Pilot pressure DIN 38524) M14 x 1.5; 12 deep 350 O
X Pilot pressure with DG-control DIN 38524) M14 x 1.5; 12 deep 350 O
MH Gauge port, high pressure DIN 3852 M14 x 1.5, 12 deep 350 X
1) For the maximum tightening torques the general instructions on page 48 must be observed.
2) Depending on the application, short-term pressure spikes can occur. Consider this when selecting measuring equipment and
fittings. Pressure values in bar absolute.
3) Only dimensions according to SAE J518, metric fastening thread deviating from the standard.
4) The spot face can be deeper than as specified in the standard.
5) Depending on the installation position, L or L1 must be connected (see also installation instructions on pages 44, 46)
O = Must be connected (plugged on delivery)
X = Plugged (in normal operation)
34/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
Drive shaft
S Splined shaft 1 3/4 in P Parallel shaft key
13T 8/16DP1) (SAE J744) DIN 6885, A14x9x80 77
67 81.5
1/2-13UNC-2B2) 4)
36
32
1.5
5
M163), 4)
48.5 -0.2
ø45 -0.005
+0.011
53
92
75
1) ANSI B92.1a, 30° pressure angle, flat root, side fit, tolerance class 5
2) Thread according to ASME B1.1
3) Thread according to DIN 13
4) For the maximum tightening torques the general instructions on page 48 must be observed.
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 35/48
DG DFLR
Two-point control, directly operated Pressure, flow and power control
139.5
L L
X
2.6
56
108
108
112
28
12 183
MH
153 209
158
DR DRG
Pressure control Pressure control, remotely operated
to flange surface
L L X
126
126
26
56
170 144
170
ED7. / ER7.
Electro-hydraulic pressure control
to flange surface
L
129
X
179
Cut A - B NG A1 A2 A3 A42)
A3 18 182 10 43.3 M10 x 1.5, 14.5
A 45° A2 deep
28 204 10 33.7 M10 x 1.5, 16 deep
45 229 10.7 53.4 M10 x 1.5, 16 deep
–0.020
Ø82.55 +0.050
Ø1 100 338 10.5 65 M10 x 1.5, 16 deep
140 350 10.8 77.3 M10 x 1.5, 16 deep
A4
B 10
to mounting flange A1
Cut A - B NG A1 A2 A3 A42)
A3 18 182 18.8 38.7 M10 x 1.5, 14.5 deep
A 45° 10 28 204 18.8 38.7 M10 x 1.5, 16 deep
45 229 18.9 38.7 M10 x 1.5, 16 deep
71 267 21.3 41.4 M10 x 1.5, 20 deep
Ø1
140 350 18.9 38.6 M10 x 1.5, 16 deep
A4
A2
B
to mounting flange A1
omitted
A4 for NG28
A2
B to mounting flange A1
Cut A - B NG A1 A2 A3 A42)
A A3 45 229 18.4 46.7 M12 x 1.75, 18 deep
45° 10
71 267 20.8 49.1 M12 x 1.75, 20 deep
100 338 18.2 46.6 M12 x 1.75, 20 deep
140 350 18.3 45.9 M12 x 1.75, 20 deep
6
Ø14
Ø101.6 +0.05
–0.02
A4
A2
B to mounting flange A1
Cut A - B NG A1 A2 A3 A42)
A3 71 267 21.8 58.6 M16 x 2,
45° 13 continuous
omitted A omitted
for NG71 for NG71 100 338 19.5 56.4 M16 x 2,
continuous
140 350 19.3 56.1 M16 x 2, 24 deep
1
Ø18
–0.02
Ø127 +0.05
A4
B A2
to mounting flange A1
A4
B
A3a
A2
to mounting flange A1
–0.02
Ø152.4 +0.07
161.6
B A2
A4
161.6 to mounting flange A1
K57 Metric 4-hole flange for mounting an R4 radial piston pump (see RE 11263)
Coupling for metric shaft key
Cut A - B NG A1 A2 A3 A4 A53)
A4 28 232 8 10.6 58.4 M8
A
A3
8 +– 0.011
0.011 45 257 8 11 81 M8
28.3 +0.2
Ø80
0
A5 A2
B
Ø25+ 00.025 to mounting flange A1
Cut A - B NG A1 A2 A3 A42)
A3 18 182 18.8 38.7 M10 x 1.5, 14.5 deep
A 10
45° 28 204 18.8 38.7 M10 x 1.5, 16 deep
45 229 18.9 38.7 M10 x 1.5, 16 deep
71 267 21.3 41.4 M10 x 1.5, 20 deep
9 100 338 19 38.9 M10 x 1.5, 20 deep
Ø10
Ø80 +0.05
–0.02
140 350 18.9 38.6 M10 x 1.5, 20 deep
A4
A2
B
to mounting flange A1
Cut A - B NG A1 A2 A3 A42)
A4
A2
B to mounting flange A1
A4
A2
B to mounting flange A1
Cut A - B NG A1 A2 A3 A42)
A3 71 267 21.8 58.6 M16 x 2,
45° 10 continuous
A
omitted omitted 100 338 19.5 56.4 M16 x 2,
for NG71 for NG71 continuous
140 350 19.3 56.1 M16 x 2, 24 deep
0
Ø18
Ø125 +0.05
-0.02
12
A4
B A2
to mounting flange A1
A4
B
A3a
A2
to mounting flange A1
B A2
A4
158.4 to mounting flange A1
Shaft key
Through-drive1) Mounting option – 2nd pump
Flange Coupling
Short A10VO/31 A10V(S)O/5x Radial piston pump Through drive
ISO 3019-2 for shaft
des. NG (shaft) NG (shaft) available for NG
key
80-2 3/4 in K57 – – R4 28 to 140
42/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
Combination pumps A10VO + A10VO Before finalizing your design request a certified
installation drawing. Dimensions in mm.
When using combination pumps it is possible to have multiple, mutually independent circuits without the need for a splitter
gearbox.
When ordering combination pumps the model codes for the first and the second pump must be joined by a "+".
Order example:
A10VSO100DFR1/31R-VSB12K04+
A10VSO45DFR/31R-VSA12N00
If no further pumps are to be factory-mounted, the simple type code is sufficient.Included in the delivery contents of the pump
with through drive are then: coupling and seal, with plastic cover to prevent penetration by dust and dirt.
It is permissible to use a combination of two single pumps of the same size (tandem pump), considering a dynamic mass
acceleration force of maximum 10 g (= 98.1 m/s2) without an additional support bracket.
Each through drive is plugged with a non-pressure-resistant cover. Before commissioning the units, they must therefore be
equipped with a pressure-resistant cover.
Through drives can also be ordered with pressure-resistant covers. Please specify in clear text.
For combination pumps comprising more than two pumps, the mounting flange must be calculated for the permissible moment
of inertia.
NG 18 28 45 71 100 140
Permissible mass moment of inertia
static Tm Nm 500 880 1370 2160 3000 4500
dynamic at 10 g (98.1 m/s2) Tm Nm 50 88 137 216 300 450
Mass with through-drive plate m kg 14 19 25 39 54 68
Mass without through drive m kg 12 15 21 33 45 60
(e.g. 2nd pump)
Distance center of gravity l mm 90 110 130 150 160 160
without bidirectional suppressor diode ____________________H If necessary, you can change the position of the connector by
turning the solenoid.
Type of protection according to DIN/EN 60529_________ IP65
To do this, proceed as follows:
The sealing ring in the screw cable fitting is suitable for line
diameters of 4.5 mm to 10 mm. 1. Loosen the mounting nut (1) of the solenoid. To do this,
turn the mounting nut (1) one revolution counter-clockwise.
The line connector is not included in the delivery contents.
This can be supplied by Bosch Rexroth on request. 2. Turn the solenoid body (2) to the desired position.
Bosch Rexroth material number: R902602623 3. Retighten the mounting nut of the solenoid. Tightening
torque: 5+1 Nm. (size WAF26, 12-pt DIN 3124)
Mounting bolt M3 Cable fitting M16x1.5
Tightening torque: tightening torque: On delivery, the position of the connector may differ from that
MA = 0.5 Nm MA = 1.5 - 2.5 Nm shown in the brochure or drawing.
65.4
(2)
(1)
Ø37
50
68.5
PE PE
A A
1 2 1 2
44/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
Installation instructions
General Below-reservoir installation (standard)
The axial piston unit must be filled with hydraulic fluid and air Below-reservoir installation means the axial piston unit is
bled during commissioning and operation. This must also be installed outside of the reservoir below the minimum fluid level.
observed following a longer standstill as the axial piston unit
empty via the hydraulic lines.
Especially with the installation position "drive shaft upwards" 1 2
or "drive shaft downward", attention must be paid to a com
a min a min
plete filling and air bleeding since there is a risk, for example,
of dry running. SB SB
ht min ht min
The case drain fluid in the motor housing must be directed to h min h min
the reservoir via the highest case drain port (L1, L2, L3).
L
For combinations of multiple units, make sure that the respec
tive case pressure in each unit is not exceeded. In the event of L L1
pressure differences at the case drain ports of the units, the S S
shared case drain line must be changed so that the minimum L1
permissible case pressure of all connected units is not exceed
ed in any situation. If this is not possible, separate case drain
lines must be laid if necessary.
To achieve favorable noise values, decouple all connecting 3 4
lines using elastic elements and avoid above-reservoir installa
tion. a min a min
In all operating conditions, the suction line and case drain line SB SB
must flow into the reservoir below the minimum fluid level. ht min ht min
h min h min
The permissible suction height hS is a result of the overall
pressure loss, but may not be greater than hS max = 800 mm.
The minimum suction pressure at port S must also not fall L1 S S
below 0.8 bar absolute during operation.
Installation position L
L1
See the following examples 1 to 12. L
Additional installation positions are available upon request.
Recommended installation positions: 1 and 3.
Installation position Air bleed Filling
1 L S + L1
2 L1 S+L
3 L1 S+L
4 L S + L1
Key, see page 45.
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 45/48
Installation instructions
Above-reservoir installation Inside-reservoir installation
Above-reservoir installation means the axial piston unit is Inside-reservoir installation is when the axial piston unit is
installed above the minimum fluid level of the reservoir. nstalled in the reservoir below the minimum fluid level.
To prevent the axial piston unit from draining, a height differ The axial piston unit is completely below the hydraulic fluid.
ence hES min of at least 25 mm at port L 1 is required in installa
If the minimum fluid level is equal to or below the upper edge
tion position 6.
of the pump, see chapter "Above-reservoir installation".
Observe the maximum permissible suction height hS max = 800 mm.
Axial piston units with electrical components (e.g. electric con
A check valve in the case drain line is only permissible in indi trol, sensors) may not be installed in a reservoir below
vidual cases. Consult us for approval. the fluid level.
5 6 9 10
a min a min
F F
hES min
L
L L1 L
S SB ht min SB ht min
S L1
L1 L
S
hs max hs max L1
h min S h min
SB SB
ht min ht min
h min h min 11 12
a min a min
a min a min
7 8
F F L1 S
S
L1 S S SB ht min SB ht min
L1
L L L
h min h min
L1
L
hs max
hs max
SB SB Installation position Air bleed Filling
ht min ht min 9 L L, L1
h min h min
10 L1 L, L1
a min a min
11 L1 S + L, L1
12 L S + L, L1
Installation position Air bleed Filling
5 F L (F)
S Suction port
6 F L1 (F)
F Filling / air bleeding
7 F S + L 1 (F) Case drain port
L, L1
8 F S + L (F)
SB Baffle (baffle plate)
ht min Minimum necessary immersion depth (200 mm)
hmin Minimum necessary spacing to reservoir bottom
(100 mm)
hES min
Minimum necessary height needed to protect the axial
piston unit from draining (25 mm).
hS max Maximum permissible suction height (800 mm)
amin When designing the reservoir, ensure adequate
distance between the suction line and the case drain
line. This prevents the heated, return flow from being
drawn directly back into the suction line.
46/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
Notes
RE 92711/01.12 | A10VSO Series 31 Bosch Rexroth AG 47/48
Notes
48/48 Bosch Rexroth AG A10VSO Series 31 | RE 92711/01.12
General instructions
–– The A10VSO pump is designed to be used in open circuit.
–– Project planning, installation and commissioning of the axial piston unit require the involvement of qualified personnel.
–– Before operating the axial piston unit, please read the appropriate instruction manual thoroughly and completely.
If necessary, request these from Bosch Rexroth.
–– During and shortly after operation, there is a risk of burns on the axial piston unit and especially on the solenoids.
Take appropriate safety measures (e.g. by wearing protective clothing).
–– Depending on the operating conditions of the axial piston unit (operating pressure, fluid temperature), the characteristics may shift.
–– Service line ports:
-- The ports and fastening threads are designed for the specified maximum pressure. The machine or system manufacturer must
ensure that the connecting elements and lines correspond to the specified application conditions (pressure, flow, hydraulic
fluid, temperature) with the necessary safety factors.
-- The service line ports and function ports are only designed to accommodate hydraulic lines.
–– Pressure cut-off and pressure control do not provide security against pressure overload. A separate pressure relief valve is to
be provided in the hydraulic system.
–– The data and notes contained herein must be adhered to.
–– The product is not approved as a component for the safety concept of a general machine according to DIN EN ISO 13849.
–– The following tightening torques apply:
-- Fittings:
Observe the manufacturer‘s instruction regarding the tightening torques of the used fittings.
-- Mounting bolts: For mounting bolts with metric ISO thread according to DIN 13 or thread according to ASME B1.1,
we recommend checking the tightening torque individually according to VDI 2230.
-- Female threads in axial piston unit:
The maximum permissible tightening torques MG max are maximum values for the female threads and must not be exceeded.
For values, see the following table.
-- Threaded plugs:
For the metal threaded plugs supplied with the axial piston unit, the required tightening torques of the threaded plugs MV
apply. For values, see the following table.
Bosch Rexroth AG © This document, as well as the data, specifications and other information set
Axial piston units forth in it, are the exclusive property of Bosch Rexroth AG. It may not be repro
An den Kelterwiesen 14 duced or given to third parties without its consent.
72160 Horb a. N., Germany The data specified above only serve to describe the product. No statements
Tel.: +49-7451-92-0 concerning a certain condition or suitability for a certain application can be de
Fax: +49-7451-82-21 rived from our information. The information given does not release the user from
the obligation of own judgment and verification. It must be remembered that our
info.brm-ak@boschrexroth.de products are subject to a natural process of wear and aging.
www.boschrexroth.com/axial-piston-pumps
Subject to change.