Professional Documents
Culture Documents
LICON Brochure - Revised - 7.12.2015
LICON Brochure - Revised - 7.12.2015
CONSTRUCTION CHEMICALS
Product Catalouge
LICON MANUFACTURING PLC., Ethiopia was incorporated
in 2009 as a subsidiary company of CONMIX Ltd. – Sharjah, Unit-
ed Arab Emirates. LICON is a Joint Venture between CONMIX
Ltd. and LICA Industries PLC.
Mission
The company plans to gradually expand the product ranges and
capacities to meet the growing needs of the market. The company
also plans to enter into the surrounding markets as a geographical
diversification strategy. With the vast experience and expertise of
the team, LICON moves forward with a vision of making CONMIX
Be the market leader in Pre Mix Plaster & Construction Chemicals in Ethiopia a successful brand in the region.
INDEX
CEMENT PLASTER
Bonding Rush Coat - BRC ....................................................................... 2-3
GYPSUM LIME PLASTER
PRE MIX PLASTER
The fair faced concrete background for 5 minutes and mix again before spraying. No further water should be added to the mix. Hard and set material should not be
Binder : Portland Cement
Mixing Ratio : 4.75 ltrs of water per 25 kg bag The mixed BRC should be sprayed on to the prepared background using a tyrolean box or a power pattern spray gun. BRC should not
Water/Powder ratio = 0.19 wood pieces, mould oil etc.
be applied using a trowel. Spray over an entire prepared area and allow some time for the applied BRC to stiffen before doubling back.
Approx. Yield * : 15.5 ltrs per 25 kg bag
The suction in the background Ensure that the applied BRC covers the entire surface area. A rough texture has to be obtained to provide a mechanical key for the
2
Approx. Coverage * : 10 m per bag at 2 mm thickness
should be neutralized by applying subsequent coat of plaster.
Density * : Wet: 1.90 kg/ltr Dry: 1.75 kg/ltr
Conmix Technical Service Department will assist in these procedures upon request.
Compressive Strength * : 15.0 N/mm2 @ 28 days potable water.
SPECIAL NOTES
Flexural Strength * : 2.5 N/mm2 @ 28 days
Free water on the surface should
The applied BRC should be water cured for a period of 2 days (3-4 times daily) and allowed to harden.
Working Time : Approx. 45 minutes
be allowed to disperse before For application procedures in case of concrete containing micro silica, GGBS, curing compound or any special additive or special building
Curing : Minimum 48 hours by potable water
material, kindly contact Conmix Technical Service Department for assistance.
Specification : BSEN998-1, BSEN13914-1, BSEN13914-2 & BS 5492 spraying BRC to avoid de-bonding
Shelf Life : 12 months from date of production when stored Conmix BRC must be stored in a dry place, off the ground and well covered. Hard or lumpy material must be rejected.
under dry conditions
APPLICATION TOOLS
www.conmix.com
1/2 PMP/BRC/ET/Ver4/07/14 PMP/BRC/ET/Ver4/07/14 2/2
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the
2 product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the 3
products as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given
in good faith. The products are guaranteed against any defect and are manufactured and sold to Conmix standard terms and conditions of sale.
CONMIX
papers. It can be applied with a suitable plastering machine or by hand in accordance to BSEN13279-1:2005. Conmix ”AUTEX” Fibre Glass Mesh/Expanded metal Lath (As approved by the consultant) to be fixed at all junctions of dissimilar
backgrounds (i.e. fair faced concrete and block work) or a groove has to be formed at the junction while the plaster is still soft.
TECHNICAL DATA APPLICATION METHOD
MIXING
Composition : Hemi-hydrated gypsum, hydrated-lime, oven dried white BACKGROUND
sand and chemical improving agents GLP1A supplied in 25 kg bags has to be mixed with potable water only, in a clean plastic bucket or clean non-corrosive, uncontaminated
The fair faced concrete
metal tub. To ensure a homogeneous and uniform mix, an electric agitator must be used.
Binder : Hemi-hydrated Gypsum background and the concrete
The amount of water to be added is 8.2 ltrs per 25 kg bag (i.e. approximately 33% by weight). Add the GLP1A to water, turn the contents
blocks should be thoroughly
Aggregate Size : 0-1 mm processed sand of the bag carefully and stir frequently. Once mixed, allow to stand for 5 minutes and mix again before applying. No further water should
cleaned using a stiff brush to
be added to the mix. Hard and set plaster should not be re-mixed or used. If a plaster spray machine is used, the mixing is carried out
Appearance : Off White granular powder remove any dust, loose particles,
wood pieces, mould oil etc. automatically.
Mixing Ratio : 8.25 ltrs of water per 25 kg bag
The suction in the background of APPLICATION
Water/Powder ratio = 0.33
both fair faced concrete and block Mixed GLP1A can be applied in a single coat onto the prepared background up to a thickness of 10 - 20 mm. The surface can be brought
Approx. Yield * : 20.6 ltrs per 25 kg bag work should be neutralized by to a very smooth finish by employing a finishing technique consisting of levelling, scraping, sponging, troweling and polishing the applied
applying potable water.
Approx. Coverage * : 1.56m2 per bag at 13 mm thickness GLP1A. If a plaster machine is used, then the plaster is applied in a continuous operation and finished manually to the specified thickness
Free water on the surface should be to meet the requirements of BSEN13279-1:2005.
Density * : Wet: 1.6 kg/ltr Dry: 1.4 kg/ltr
allowed to disperse before applying Conmix Technical Service Department will assist in these procedures upon request.
Compressive Strength * : 5.0 N/mm2 @ 28 days GLP 1A.
SPECIAL NOTES
Preparation of normal fair
Flexural Strength * : 1.2 N/mm2 @ 28 days The applied GLP1A should be allowed dry out as quickly as possible. Windows and doors should be kept open and maximum ventilation
faced concrete surface
should be permitted. GLP1A should not be water cured.
Working Time : Approx. 40 minutes Conmix Bonding Rush Coat - BRC
Before applying any kind of stucco finish, paint or wall paper, the plaster has to be allowed to dry out completely, devoid of any moisture.
mixed with appropriate amount of
Curing : Water curing is not required
For application procedures in case of light weight blocks, concrete containing micro silica, GGBS curing compound or any special
potable water (approximately 19%
Specification : ASTMC28, 207, BS5492 & BSEN13279-1:2005 by weight i.e. 4.75 ltrs per 25 kg additive or special building material, kindly contact Conmix Technical Service Department for assistance.
APPLICATION TOOLS
www.conmix.com
1/2 PMP/GLP1A/ET/Ver4/07/14 PMP/GLP1A/ET/Ver4/07/14 2/2
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the
4 product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the 5
products as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given
in good faith. The products are guaranteed against any defect and are manufactured and sold to Conmix standard terms and conditions of sale.
CONMIX
and other contaminations, which may adversely affect adhesion and cause variation in colour of the SP1.
TECHNICAL DATA APPLICATION METHOD It is essential to neutralize the suction of the background before SP1 is applied. This is done by applying potable water evenly on the
surface. A short time should elapse to allow the free water to disperse before applying SP1 else it may cause de-bonding and variation
Composition : White Portland Cement, marble chips, hydrated lime, BACKGROUND
in colour of the finished product.
non-fading pigments and chemical improving agents.
It is recommended that Conmix
MIXING
Binder : White Portland Cement Decorative Plaster Roll Easy-SP1
SP1 supplied in 25 kg bags must mixed with potable water only, in a clean plastic bucket or clean non-corrosive, uncontaminated metal
Aggregate Size : 0-0.5 mm should be applied over a Portland
tub. To ensure a homogeneous and uniform mix, an electric agitator must be used. The amount of water to be added is approximately
Cement based render mix type-II
Appearance : Fine granular powder, available in different colours 6.5 ltrs per 25 kg bag of SP1 (i.e. 26% by weight) and should be constant for every batch. Add SP1 to water, turn the contents of the
(BSEN13914-1) which is rough
Mixing Ratio : 6.5 ltrs of water per 25 kg bag. bag carefully adding small amounts at a time into the container. Stir frequently and mix each batch for the same period of time.
finished using either a wooden or
Water/Powder ratio = 0.26 Once mixed, allow to stand for 3-5 minutes and mix again before applying. No further water should be added to the mix. Hard and set
plastic float. Where the render has
material should not be re-mixed or used.
Approx. Yield * : 19.5 ltrs per 25 kg bag
to be applied over dissimilar
APPLICATION
Approx. Coverage * : 13 m2 per 25 kg bag at 1.5 mm thickness
backgrounds i.e. concrete and
The mixed SP1 is applied to the prepared background to a thickness of 1.5 mm using a roller. Light, medium or heavy textured finish
Density * : Wet : 1.6 kg/ltr Dry : 1.5 kg/ltr block work (prior to the application
can be obtained by moving the roller in a vertical or horizontal direction over the applied surface.
of SP1), it is important that the
Compressive Strength * : 7 N/mm2 @ 28 days Conmix Technical Service Department will assist in these procedures upon request.
substrates are sound, free of
Flexural Strength * : 2 N/mm2 @ 28 days SPECIAL NOTES
undue shrinkage, structural,
Working Time : Approx. 45 minutes SP1 has to be protected from direct wind, sunlight and rain during application. SP1 should be applied in one continuous operation up to
tensile and thermal movements.
angles, features or in panels to prevent joints showing on the finished surface. SP1 has to be water cured for at least 2 days (3-4 times
Curing : Minimum 48 hours by potable water The rendered background should
daily) by applying a fine mist spray of potable water over the entire surface.
Specification : BSEN998-1, BSEN13914-1, BSEN13914-2 & BS 5492 be cured with water for a period of
STORAGE
2 days (3-4 times daily) and
Pack Size : 25 kg paper bags Conmix SP1 must be stored in a dry place, off the ground and well covered. Hard or lumpy material must be rejected.
allowed to harden before applying
Shelf Life : 12 months from date of production when stored
SP1.
under dry conditions
APPLICATION TOOLS
www.conmix.com
1/2 PMP/SP1/ET/Ver4/07/14 PMP/SP1/ET/Ver4/07/14 2/2
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the
6 product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the 7
products as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given
in good faith. The products are guaranteed against any defect and are manufactured and sold to Conmix standard terms and conditions of sale.
CONMIX
and other contaminations which may adversely affect adhesion and cause variation in colour of the SP2.
It is essential to neutralize the suction of the background before SP2 is applied. This is done by applying potable water evenly on the
TECHNICAL DATA APPLICATION METHOD
surface. A short time should elapse to allow the free water to disperse before applying SP2 else it may cause de-bonding and variation
Composition : White Portland Cement, marble chips, hydrated lime, BACKGROUND
in colour of the finished product.
non-fading colour pigment and chemical improving agents
It is recommended that Conmix
MIXING
Binder : White Portland Cement Decorative Plaster-SP2 should be
SP2 supplied in 25 kg bags must be mixed with potable water only, in a clean plastic bucket or clean non-corrosive, uncontaminated
applied over a Portland Cement
Aggregate Size : 0-3.5 mm metal tub. To ensure a homogeneous and uniform mix, an electric agitator must be used. The amount of water to be added is
based render mix type-II (BS
Appearance : Granular powder, available in different colours approximately 5.5 ltrs per 25 kg bag of SP2 (i.e. 22% by weight) and should be constant for every batch. Add SP2 to water, turn the
5262) which is rough finished
contents of the bag carefully adding small amounts at a time into the container. Stir frequently and mix each batch for the same period
Mixing Ratio : 5.5 ltrs of water per 25 kg bag using either a wooden or plastic
of time. Once mixed, allow to stand for 3-5 minutes and mix again before applying. No further water should be added to the mix. Hard
Water/Powder ratio = 0.22
float. Where the render has to be
and set plaster should not be re-mixed or used.
Approx. Yield * : 17.75 ltrs per 25 kg bag applied over dissimilar
APPLICATION
backgrounds i.e. concrete and
Approx. Coverage * : 7.1 m2 per bag at 2.5 mm thickness
Apply the mixed SP2 onto the prepared background to a thickness for approximately 2-3 mm, float finish with a plastic float, working over
block work (prior to the application
Density * : Wet : 1.7 kg/ltr Dry : 1.65 kg/ltr the surface in a circular, horizontal or vertical directions to achieve an even and textured decorative plaster.
of SP2), it is important that the
Conmix Technical Service Department will assist in these procedures upon request.
Compressive Strength * : 6 N/mm2 @ 28 days substrates are sound, free of
APPLICATION TOOLS
www.conmix.com
1/2 PMP/SP2/ET/Ver4/07/14 PMP/SP2/ET/Ver4/07/14 2/2
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the
8 product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the 9
products as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given
in good faith. The products are guaranteed against any defect and are manufactured and sold to Conmix standard terms and conditions of sale.
CONMIX
Aggregate Size : 0-1.5 mm based render mix type-II (BSEN metal tub. To ensure a homogeneous and uniform mix, an electric agitator must be used. The amount of water to be added is
13914-1) which is rough finished approximately 5.25 ltrs per 25 kg bag of SP3 (i.e. 21% by weight) and should be constant for every batch. Add SP3 to water, turn the
Appearance : Granular powder, available in different Colours
using either a wooden or plastic contents of the bag carefully adding small amounts at a time into the container. Stir frequently and mix each batch for the same period
Mixing Ratio : 5.25 ltrs of water 25 kg bag. float. of time. Once mixed, allow to stand on 3-5 minutes and mix again before applying. No further water should be added to the mix. Hard
Water/Powder ratio = 0.21 and set plaster should not be re-mixed or used.
Where the render has to be
Approx. Yield * : 18.25 ltrs per 25 kg bag applied over dissimilar APPLICATION
backgrounds i.e. concrete and SP3 to be applied to a thickness of 1.5 - 2 mm and finished using the following techniques.
Approx. Coverage * : 12.2 m2 per bag at 1.5 mm thickness
block work (prior to the application 1. Float finish with a plastic trowel working over the surface in a circular, horizontal or vertical direction to achieve a semi-rough thin
Density * : Wet: 1.65 kg/ltr Dry: 1.55 kg/ltr of SP3), it is important that the coat Decorative Render.
Compressive Strength * : 6 N/mm2 @ 28 days substrates are sound, free of 2. Use a power pattern spray gun or Tyrolean box to achieve a textured spray finish.
undue shrinkage, structural, Conmix Technical Service Department will assist in these procedures upon request.
Flexural Strength * : 1 N/mm2 @ 28 days
tensile and thermal movements.
SPECIAL NOTES
Working Time : Approx. 45 Minutes The rendered background should SP3 has to be protected from direct wind, sunlight and rain during application.
be cured with water for a period of SP3 should be applied in one continuous operation up to angles, features or in panels to prevent joints showing on the finished surface.
Curing : Minimum 48 hours by potable water
2 days (3-4 times daily) and SP3 has to be water cured for at least 2 days (3-4 times daily) by applying a fine mist spray of potable water over the entire surface.
Specification : BSEN998-1, BSEN13914-1, BSEN13914-2 & BS5492
allowed to harden before applying
STORAGE
Pack Size : 25 kg paper bags SP3.
Conmix SP3 must be stored in a dry place, off the ground and well covered. Hard or lumpy material must be rejected.
Shelf Life : 12 months from date of production when stored
under dry conditions
www.conmix.com
1/2 PMP/SP3/ET/Ver4/07/14 PMP/SP3/ET/Ver4/07/14 2/2
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the
10 product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the 11
products as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given
in good faith. The products are guaranteed against any defect and are manufactured and sold to Conmix standard terms and conditions of sale.
CONMIX
MIXING
TECHNICAL DATA APPLICATION METHOD
SP Tyrolean supplied in 25 kg bags has to be mixed with potable water only, in a clean plastic bucket or a clean non-corrosive,
Composition : White Portland Cement, hydrated lime, graded sand, BACKGROUND uncontaminated metal tub. To ensure a homogeneous and uniform mix, an electric agitator must be used. The amount of water to be added
non-fading colour pigments and chemical improving agents Conmix Decorative Plaster-SP
is approximately 4.5 ltrs per 25 kg bag (i.e. 18% by weight) and should be constant for every batch. Add SP Tyrolean to water, turn the
Tyrolean can be applied over a
Portland Cement based render contents of the bag carefully adding small amounts at a time into the container. Stir frequently and mix each batch for the same period of
Binder : White Portland Cement mix type-II (BSEN 13914-1),
concrete block work or other time. Once mixed, allow to stand for 3-5 minutes and mix again before applying. No further water should be added to the mix. Hard and set
Aggregate Size : 0-0.6 mm mineral based keyed surfaces. plaster should not be re-mixed or used.
The rendered background should
be cured with water for a period of APPLICATION
Appearance : Powder, available in different colours
2 days (3-4 times daily) and
allowed to harden before applying SP Tyrolean to be applied and finished using the following techniques.
Mixing Ratio : 4.5 ltrs of water per 25 kg bag SP Tyrolean.
Water/Powder ratio = 0.18 Preparation of normal fair- TYROLEAN FINISH
faced concrete surface A Tyrolean finish can be achieved by using a Tyrolean box or a spray machine i.e. spray pattern hopper gun or any other suitable
Approx. Yield * : 15.75 lrs. per 25 kg bag Conmix Bonding Rush Coat (BRC)
machine. Spray from a wet edge to complete an entire unbroken area in one continuous operation. Allow the sprayed material to stiffen
mixed with appropriate amount of
Approx. Coverage * : 5 m2 per bag at 4-5 mm thickness potable water (approximately 19% slightly and then double back to achieve a sprayed thickness of approx. 4-5 mm. Over spraying of dried, finished areas should be
by weight i.e. 4.5 ltrs per 25 kg
bag) using a mechanical mixer, avoided.
Density * : Wet : 1.85 kg/ltr Dry : 1.7 kg/ltr should be spray applied on the STUCCO FINISH
prepared fair faced concrete
Compressive Strength * : 6 N/mm2 @ 28 days surface. A rough texture has to be The high points in the Tyrolean texture can be smoothened over with a wetted steel or plastic trowel once the plaster starts to stiffen,
obtained to provide a mechanical to achieve a stucco finish.
key for the subsequent coat of SP
Flexural Strength * : 1.5 N/mm2 @ 28 days Tyrolean. The applied BRC should Conmix Technical Service Department will assist in these procedures upon request.
be water cured for a period of 2
Working Time : Approx. 45 Minutes days (3-4 times daily) before SPECIAL NOTES
applying SP Tyrolean.
SP Tyrolean has to be protected from direct wind, sunlight and rain during application. SP Tyrolean should be applied in one continuous
Curing : Minimum 48 hours by potable water The background for application of
SP Tyrolean should be clean, free operation up to angles, features or in panels to prevent joints showing on the finished surface. SP Tyrolean has to be water cured for at
Specification : BS5492, BSEN998-1, BSEN13914-1, BSEN13914-2:2005 of dust deposits, loose mortar, least 2 days (3-4 times daily) by applying a fine mist spray of potable water over the entire surface.
chemical impurities (salts and
sulphates) and other
Pack Size : 25 kg paper bags STORAGE
contaminations, which may
adversely affect adhesion and Conmix SP Tyrolean must be stored in a dry place, off the ground and well covered. Hard or lumpy Material must be rejected.
Shelf Life : 12 months from date of production when stored cause variation in colour of the SP
Tyrolean.
under dry conditions
Cont...
APPLICATION TOOLS
www.conmix.com
1/2 PMP/SP Tyrolean/ET/Ver4/07/14 PMP/SP Tyrolean/ET/Ver4/07/14 2/2
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the
12 product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the 13
products as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given
in good faith. The products are guaranteed against any defect and are manufactured and sold to Conmix standard terms and conditions of sale.
CONMIX
uncontaminated metal tub. To ensure a homogeneous and uniform mix, an electric agitator or paddle mixer must be used.
TECHNICAL DATA APPLICATION METHOD The amount of water to be added is 7 ltrs per 25 kg bag (i.e. approximately 28% by weight). Add C800 to water, turn the contents
of the bag carefully and stir frequently. Once mixed allow to stand for 5 minutes and mix again before applying. No further water
Composition : White portland cement, oven dried, processed sand and Background
chemical additives including vinyl acetate/ethylene should be added to the mix. The mixed mortar must be used within 30 minutes. Hard and set mortar should not be remixed.
Conmix C800 is a thin bed cement
copolymer redispersible powder. based mortar suitable for fixing No further water should be added to the mix.
APPLICATION TOOLS
www.conmix.com
1/2 PMP/C800/ET/Ver5/07/14 PMP/C800/ET/Ver5/07/14 2/2
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the
14 product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the 15
products as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given
in good faith. The products are guaranteed against any defect and are manufactured and sold to Conmix standard terms and conditions of sale.
CONMIX
APPLICATION TOOLS
www.conmix.com
1/2 PMP/C500/ET/Ver5/07/14 PMP/C500/ET/Ver5/07/14 2/2
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the
16 product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the 17
products as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given
in good faith. The products are guaranteed against any defect and are manufactured and sold to Conmix standard terms and conditions of sale.
CONMIX
Approx. Coverage * : Coverage depends on tile size the joints to be grouted as this joints. The excess material on the surface of the tile should be removed using a dry cloth. The grouting should be carried out in
Density * : Wet : 1.8 kg/ltr Dry : 1.7 kg/ltr could lead to de-bonding.
accordance to the relevant standards and code of practice.
Compressive Strength * : 22 N/mm2 @ 28 days
Conmix Technical Service Department will assist in these procedures upon request.
Flexural Strength * : 3.0 N/mm2 @ 28 days
SPECIAL NOTES
Working Time : Approx. 30 minutes
Curing : 48 hours by potable water Grouting should commence only after the tile glue / adhesive has dried out completely. The applied Tile Joint Filler should be properly cured.
APPLICATION TOOLS
www.conmix.com
1/2 PMP/TJF/ET/Ver5/07/14 PMP/TJF/ET/Ver5/07/14 2/2
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the
18 product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the 19
products as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given
in good faith. The products are guaranteed against any defect and are manufactured and sold to Conmix standard terms and conditions of sale.
CONMIX
metal tub. To ensure a homogenous and uniform mix, an electric agitator must be used.
TECHNICAL DATA APPLICATION METHOD
The amount of water to be added is 6 ltrs per 25 kg bag (i.e approximately 24% by weight). Add LC11 to water, turn the contents of the
Composition : Portland cements, hydrated lime, processed sand, fibre BACKGROUND
bag carefully and stir frequently. Once mixed, allow to stand for 5 minutes and mix again before applying. No further water should be
and chemical additives.
Conmix Skim Coat Plaster LC11 is
a pre mix sand cement mortar for added to the mix. Hard and set plaster should not be mixed or used.
Binder : Portland Cement
internal and external use. It is
Aggregate Size : 0 - 0.6 mm recommended as a finishing coat APPLICATION
or repair mortar onto Portland
LC11 mixed as above can be applied to the prepared backgrounds in one coat thickness of 3-8 mm. LC11 should be applied to the
Appearance : Grey granular powder Cement based backgrounds such
as concrete or rendered surfaces. background with a trowel and levelled. Wet the surface slightly and using a plastic float the surface can be rough finished.
Mixing Ratio : 6 ltrs of water per 25 kg LC11 is ideal material for dubbing
Water/Powder ratio = 0.24 out and levelling of backgrounds If necessary, the surface can be closed with a steel trowel and finished smooth, however overworking should be avoided.
or as a thin coat plaster.
Approx. Yield * : 17 ltrs per 25 kg bag Conmix Technical Service Department will assist in these procedures upon request.
The density, smoothness and
Approx. Coverage * : 4.25 m2 per bag at 4 mm thickness suction of the background,
SPECIAL NOTES
concrete, render etc. will vary.
Density * : Wet: 1.80 kg/ltr Dry: 1.6 kg/ltr The work should not be started The finished plaster should be water cured for a period of 2 days (3-4 times daily).
until the background has been
Compressive Strength * : 8 N/mm2 @28 days Before applying any kind of Stucco Finish, paint or wallpaper, the plaster has to be allowed to dry out completely, devoid of any moisture.
properly prepared.
Flexural Strength * : 2 N/mm2 @28 days The background should be For application procedure in case of light weight blocks, GGBS, concrete containing micro silica, curing compound or any special additive
thoroughly cleaned devoid of dust,
Working Time : Approx. 45 minutes loose particles, wood pieces, or special building material, kindly contact Conmix Technical Service Department for assistance.
mould oil etc.
Curing : 48 hours by potable water
STORAGE
The suction in the background
Specification : BS5492, BSEN13914-I & II:2005 should be neutralized by applying Conmix LC11 must be stored in a dry place, off the ground and well covered. Hard or lumpy material must be rejected.
potable water. Free water on the
Pack Size : 25 kg paper bags surface should be allowed to
disperse before applying LC11
Shelf-Life : 12 months from date of production when
else it may cause de-bonding.
stored under dry conditions
APPLICATION TOOLS
www.conmix.com
1/2 PMP/LC11/ET/Ver5/07/14 PMP/LC11/ET/Ver5/07/14 2/2
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the
20 product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the 21
products as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given
in good faith. The products are guaranteed against any defect and are manufactured and sold to Conmix standard terms and conditions of sale.
CONMIX
CONMIX CONPUTTY
Prelude to paint...
The amount of water to be added is approximately 9.0 ltrs per 25 kg bag. Add conputty to water, turn the contents of the bag carefully and
Conmix Conputty is a dry pre mix, smooth finish, leveling compound for internal and external use. It is used to fill small
voids, level and smoothen surface irregularities on concrete, sand cement render and various mineral backgrounds prior frequently. Once mixed, allow to stand for 5 minutes and mix again before applying. Mixed putty should be used within 45 minutes.
to the application of paint or wall paper.
Mix only quantities that can be applied within 45 minutes at 30ºC. Hard and set mortar should not be re-mixed or used.
TECHNICAL DATA APPLICATION METHOD
APPLICATION
Composition : White Portland Cement, special puzzolonic fillers, BACKGROUND
chemical improving agents and polymer additives Surface to be leveled should be Conputty mixed as above is applied onto the prepared background using a painter’s spatula. Do not use a masons trowel. Build up
Appearance : White powder Apply potable water on the surface Paint can be applied on Conputty after it has completely dried out.
to be levelled to neutralize suction.
Mixing Ratio : 9.0 ltrs water per 25 kg bag SPECIAL NOTES
A short time should elapse to allow
Approx. Coverage * : 42.5 m2/25 kg bag at 0.5 mm Areas that dry out fast or in high Before applying any kind of stucco finish, paint or wallpaper, the putty has to be allowed to dry out completely, devoid of any moisture.
ambient temperatures, the surface
Density * : Wet 1.6 kg/ltr Dry 1.5 kg/ltr For application procedure in case of light weight blocks, concrete containing micro silica, GGBS, curing compound or any special additive
should be wetted frequently. As a
Compressive strength * : 10 N/mm2 @28 days rule, ensure that the surface is or building material, Conmix Technical Service Department will assist upon request..
damp before applying Conputty.
Flexural strength * : 3 N/mm2 @28 days STORAGE
MIXING
Working time : Approx. 45 minutes Conputty supplied in 25 kg bags Conmix Conputty must be stored in a dry place, off the ground and well covered. Hard or lumpy material must be rejected.
Shelf Life : 12 months from date of manufacture when stored in dry electric drill.
conditions Cont...
APPLICATION TOOLS
www.conmix.com
1/2 PMP/Conputty/ET/Ver4/07/14 PMP/Conputty/ET/Ver4/07/14 2/2
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the
22 product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the 23
products as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given
in good faith. The products are guaranteed against any defect and are manufactured and sold to Conmix standard terms and conditions of sale.
CONMIX
Application tools
www.conmix.com
1/2 PMP/C400/ET/Ver4/07/14 PMP/C400/ET/Ver4/07/14 2/2
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the
24 product is suitable for the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the 25
products as it does not have any control over installation or end use of product. All information and in particular the recommendations relating to application and end use are given
in good faith. The products are guaranteed against any defect and are manufactured and sold to Conmix standard terms and conditions of sale.
Surface Preparation
CONMIX The surface should be sound, clean, dry and free from oil or grease.
Application
Material has to be thoroughly stirred prior to the application. Using brush or roller, lay the material onto the
surface to achieve the required film thickness per coat. Avoid brushing out. Surfaces should be uniformly coated
POLYMER EMULSION COAT and free from voids, blisters or pin holes. Before recoating, previous coat must have been adequately cured. All
Water based protective coating for internal and external application dirt, dust or contaminants should be removed before applying the subsequent coat. Film thickness can be checked
CONMIX POLYMER EMULSION COAT is a ready to use liquid based surfactant stabilised,
General Information
fine particle sized, high quality alkali resistant Crosslinked Acrylic Co-polymer Emulsion.
Shelf Life : Shelf life of 12 months from the date of manufacturing if stored in original sealed
It gives smooth, matt finish with excellent washability and good hiding property. It also offers
containers in dry conditions. Shelf life may be reduced if stored at high temperatures.
exceptional light and weather resistance. It contains additives to inhibit the growth of fungi
Health & Safety : Conmix Polymer Emulsion Coat is non flammable and is classified as non hazardous.
and bacteria. It provides decorative smooth finish over exterior & interior backgrounds such
as concrete, plaster, decorative plaster, masonry, brick work, gypsum, asbetos and wood. Gloves and goggles should be worn during application. Wash off splashes on skin with
water. Wash with plenty of clean water and seek medical attention in case of contact
with eyes.
Technical Service : Conmix Technical Service Department is available to assist you in the correct use of
Typical Properties
our products.
Colour As per Conmix standard shade card
Finish Smooth, Matt
Volume of solids (105ºC, 2 hours) * 44 ± 1%
Specific gravity at 25ºC *3 1.40 - 1.55 gm/cc
Theoretical coverage * 3 - 5.0 m2/ltr @ 50 micron dft
WFT 90 - 120 microns
Drying time at 25ºC Tack free : 45 - 60 minutes Packaging
Recoating time : 2-4 hours depending
on atmospheric conditions, film thickness. 20 ltrs pail
Full Cure : 7 days
NanoGrout GP
Non-Shrink Cementitious Performance Grout NanoGrout GP
DESCRIPTION NanoGrout GP is a cement based, non-metallic, non-shrink, free flowing grout that
maintains a fluid consistency for a longer duration. SURFACE PREPARATION Surfaces should be clean, sound, free from oil, grease, laitance and loose particles.
Saturate concrete substrate with water at least 3 - 4 hours prior to pouring the grout. Any
STANDARDS ASTM C1107
standing water should be removed just before placing the grout. Ensure that there is no
USES NanoGrout GP can be used for grouting of bolt pockets, gaps between the base plate standing water in bolt pockets. Metal surfaces should also be clean and free from rust, oil
and concrete such as bridge bearings, machinery base-plates, stanchion base plates,
joints between precast panels, rail and anchor bolts, etc. Can be used for filling precast and grease.
joints and tie holes with adjustable consistency. Can be used for reinstating damaged
structural elements by placing within the formwork.
MIXING NanoGrout GP should be mixed using a suitable mechanical grout mixer. For small
ADVANTAGES • Ready to use, only requires addition of water volumes it is recommended to use a drilling machine fitted with a paddle. For large
• Flowable and self levelling
works, high shear vane grout mixer is to be used. Powder should be added to the
• Can fill intricate voids
• High strength pregauged water. A free flowing and self levelling grout can be obtained at a mix ratio of
• No bleeding or segregation
25 kg powder to 4.0 litres of water. Mix until uniform consistency is achieved. Chilled or
• Controlled expansion
cold water will give enhanced flowability. NanoGrout GP can also be used as dry pack
TYPICAL PROPERTIES at 25°C mortars of various consistency by adjusting the water content of the mix.
30 CC/NG05/Ver8/07/14
CC/ET/NG05/Ver8/07/14 1/4 Technical Datasheet CC/NG05/Ver8/07/14
CC/ET/NG05/Ver8/07/14 2/4 Technical Datasheet 31
Construction Chemicals Construction Chemicals
NanoGrout GP NanoGrout GP
enough grout in place before starting. Start pouring the mixed grout from one side of the TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the
formwork to prevent entrapment of air. This can be achieved by pouring the grout to the correct use of its products.
shortest distance. It is advisable to use heavy duty diaphragm pump when large
volumes are to be placed. During application ensure entrapped air is able to escape
through relief holes. Maintain continuous head during grouting. Grout flow should not be
interrupted. Check for any grout loss through the formwork or between any unsealed
joints. Plug the same using MoyaProof Plug.
CURING To prevent rapid surface drying and crazing, exposed surface of grout should be cured
with wet burlap or moist hessian or use a suitable curing compound from JetCure range.
NOTE Use NanoGrout GP for minimum gap of 10 mm and maximum thickness of 100 mm. For
thickness above 100 mm, NanoGrout GP can be mixed with hard, clean, surface
saturate dry (SSD), graded 10 mm aggregates in the ratio of 1:1 or 1:0.5 by weight
depending on consistency required. Exact proportion should be determined by
conducting site trials. Ambient temperature will affect setting time and strength gain. Use
of chilled water will ensure better flow and retention properties.
LIMITATIONS NanoGrout GP should not be used in the unrestrained areas as it may lead to the
cracking of grout. Shoulder space between baseplate and formwork should be as
minimum as possible. Grout surface on the shoulders may be sprinkled with aggregates
or restrained to minimize the cracks.
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
warehouse conditions in original unopened packing.
Extreme temperature / humidity may reduce shelf life.
Cleaning Clean all equipments and tools with water immediately after use.
HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
Precautions Contact with skin, eyes, etc. must be avoided. If swallowed Manufacturer:
Manufacturer:
LICON MANUFACTURING PLC.
CONMIX
P.O.Box LTD.
5452, Addis Ababa, Ethiopia
seek medical attention immediately. P.O. Box
Tel: 5936,
+ 251 Sharjah 5544557/8
11 5544334,
United+251
Mob: Arab930109893
Emirates Sales Office:
Tel: +971
+2516115314155 Tel: +971 6 5682422
Hazard Regarded as non-hazardous for transportation. Fax: 5543610
Fax: +971 6 5314332 Fax: +971 6 5681442
Email: ethiopia@conmix.com
Email: conmix@conmix.com www.conmix.com
www.conmix.com
Disposal Do not reuse bags. To be disposed off as per local rules and
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
regulations. product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
Additional Information Refer MSDS. (Available on request.) good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
32 CC/NG05/Ver8/07/14
CC/ET/NG05/Ver8/07/14 3/4 Technical Datasheet CC/NG05/Ver8/07/14
CC/ET/NG05/Ver8/07/14 4/4 Technical Datasheet 33
Construction Chemicals Construction Chemicals
NanoGrout Aid
NanoGrout Aid
Plasticising and Expanding Additive
For Post-Tensioned Cable Duct Grouting
DESCRIPTION NanoGrout Aid is a non-shrink additive in powder form. It makes the grout mix Cavity / Baseplate Grouting:
cohesive and free from segregation and bleeding. It is designed to allow uniform Roughen all concrete surfaces by wire brushing, grinding or other mechanical means to
expansion while maintaining high fluidity.
ensure a good bond. Loose or broken concrete should be removed. The concrete
STANDARDS BSEN 934-4 surfaces should be saturated with water at least 3-4 hrs prior to the application of grout.
Any standing water should be removed prior to the placement of the grout. Leak proof
USES Used as an additive in cement, concrete to provide non-shrink properties. Applications and strong formwork should be in place prior to placement of grout.
include grouting of post tensioned cable ducts, bearing plates, tunnel linings, sheet pile
anchors, rock and soil anchoring, concrete crack injection, non-shrink concrete, etc.
MIXING For best results a mechanically powered grout mixer should be used. For quantities upto
ADVANTAGES • Improved fluidity at reduced mix water content 50-60 kg, slow speed drill fitted with a paddle can be used. Water should be measured
• Prolongs workability
accurately into mixer. Slowly add cement and start mixing. NonoGrout Aid should be
• Reduces bleeding and segregation
• Good strength and adhesion slowly added and further mixed for 3 to 4 minutes. Ensure that the grout has a smooth
• Improved cohesion
and even consistency after mixing. For high volume grouting, use of high shear vane,
• Protects against corrosion of pre-stressing wires
professional grout mixer and pumps is recommended.
Fresh Wet Density BSEN 445 2.00 kg/ltr +/- 0.05 Grouting process should start from one side of the cable duct till homogenous
BSEN 445 consistency of grout flows from consecutive air vent valves and outlet valves.
Flow (Marsh Cone)* W/P 0.36 0.32
ReCon GP
NanoGrout Aid Cementitious Structural Grade Repair Mortar
PACK SIZE 20kg DESCRIPTION ReCon GP is a ready to use single component polymer modified repair mortar
containing fibres and silica fume. It contains specially selected materials to provide a
fine, smooth repaired surface.
DOSAGES Normal dosage at 4-8% by weight of cementitious material. Actual dosage to be
confirmed after site trials.
USES ReCon GP is a fine, ready to use repair mortar for repairing load bearing structures,
precast concrete elements, etc. It can also be used to repair honeycombs, surface
YIELD OPC 0-5 mm Water NanoGrout Approx.
defects, blowholes, tie rod holes and minor damages. It can be used in vertical,
Sand Aid Yield
overhead and floor patch repair situations with ease. It can also be used as dry pack
50kg Nil 17 litre 3.00kg 34 litre mortar of various consistencies by adjusting the water content of the mix.
HEALTH and SAFETY PPE's Gloves, goggles and suitable mask must be worn.
Precautions Contact with skin, eyes etc. must be avoided. TYPICAL PROPERTIES at 25°C with W/P ratio at 0.16
Manufacturer:
Manufacturer:
LICON MANUFACTURING
LICON MANUFACTURING PLC.
PLC.
P.O.Box
P.O. 5452, Addis
Box 5452, AddisAbaba,
Ababa,Ethiopia
Ethiopia SURFACE PREPARATION The area to be repaired should be clearly marked and saw cut for at least 5 mm depth to
Tel: +251
Tel: + 2511111 5544334, 5544557/8
5544334
Mob: +251 930109893
Tel: +251 11 5544557/8 avoid feather edges. The surface should be clean and sound. Remove dirt, dust, oil,
Fax: +251
Fax: +25111115543610
5543610
Email: ethiopia@conmix.com
Email: ethiopia@conmix.com grease, laitance, sealers, release agents, curing compounds and paints using suitable
www.conmix.com
www.conmix.com
mechanical means. Exposed rebar should be cleaned and protected with ReCon Zinc
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the or ReCon ST. The concrete should be saturated with water prior to application.
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
ReCon GP ReCon GP
PRIMING Priming is generally not required. Surfaces to receive ReCon GP should be well GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
saturated with water prior to application and excess water has to be removed before warehouse conditions in original unopened packing.
application of ReCon GP. In some critical cases appropriate bonding agent from Extreme temperature / humidity may reduce shelf life.
FitBond range can be used. Cleaning Clean all equipments and tools with water immediately after
use.
MIXING ReCon GP should be mixed with water using a heavy duty slow speed drill machine
fitted with a paddle. Amount of water to be added is 4 ltrs per 25 kg bag. Mix for at least 3
HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
minutes to ensure a homogeneous lump free consistency. Do not try to remix the product
Precautions Contact with skin, eyes, etc. must be avoided.
after it loses its workability by adding more water.
Hazard Regarded as non-hazardous for transportation.
Disposal Do not reuse bags. To be disposed off as per local rules and
APPLICATION ReCon GP can be applied by hand or wet spray. It should be firmly placed to ensure
regulations.
proper bonding to the prepared surface. Wooden float or plastic float may be used for
Additional Information Refer MSDS. (Available on request.)
levelling and initial finishing. Final finish can be carried out just before the initial set of
material using a steel trowel. Single layer application can be carried out to a maximum
TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the
thickness of 40 mm. Thicker repairs may be achieved by working in layers.
correct use of its products.
CURING To prevent rapid surface drying and crazing, repair mortar should be cured by spreading
wet burlap or moist hessian cloth over the surface. Repaired area can also be cured
using suitable curing compound from JetCure range.
LIMITATIONS At temperatures above 35°C, it is recommended that measures are taken to reduce
material placing temperatures. These include: storing materials and equipments under
Manufacturer:
Manufacturer:
cool shade and away from direct sunlight. Avoid installation during the hottest part of the LICON MANUFACTURING
LICON MANUFACTURING PLC.
PLC.
P.O.Box
P.O. 5452, Addis
Box 5452, AddisAbaba,
Ababa,Ethiopia
Ethiopia
Tel: +251
+ 2511111 5544334, 5544557/8
day. Ensure that water temperature is kept below 20°C. Tel:
Mob:+251
Tel:
5544334
+25111930109893
5544557/8
Fax: +251
Fax: +25111115543610
5543610
Email: ethiopia@conmix.com
Email: ethiopia@conmix.com
www.conmix.com
www.conmix.com
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
ReForm S
Chemically Active Form Release Agent ReForm S
DESCRIPTION ReForm S is a chemical based form release agent designed to provide a fast, clean, and Cleaning Clean all equipments and tools with Conmix Cleaner
easy release of concrete from formwork without staining. immediately after use.
USES ReForm S can be used for steel, wooden or plastic forms in precast industry, cast in situ HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
concrete, coloured concrete, architectural finishes, etc. Precautions Contact with skin, eyes, etc must be avoided. If swallowed,
seek medical attention immediately.
ADVANTAGES • Ready to use Hazardous Regarded as hazardous for transportation.
• Spray or roller application Disposal Do not reuse containers. To be disposed off as per
• Built in rust inhibitors local rules and regulations.
• Produces high quality concrete surfaces ready to paint, coat or seal Additional Information Refer MSDS. (Available on request.)
• No staining on concrete surface
• Resistant to rain TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the
• Non slip correct use of its products.
• Progressively better results on wooden formwork
• Economical
• Minimizes surface defects
Component - Single
Form - Liquid
SURFACE PREPARATION Moulds must be dry, clean, free of rust and foreign matter prior to the application of
ReForm S . Any surface repairs done with putty should be totally cured and dry. Moulds
should be protected from dust storm or rain during application.
APPLICATION ReForm S is ready to use and should be applied by conventional mould oil sprayer,
brush or sponge. It should be applied in one continuous film as thinly and evenly as
possible to avoid reflectance of oil on the concrete surface. Excess material that pools
should be wiped up with a sponge.
Manufacturer:
Manufacturer:
COVERAGE 30-50 m²/ltr/coat (coverage depends on surface finish, porosity and texture of moulds) LICON MANUFACTURING
LICON MANUFACTURINGPLC.
PLC.
P.O.Box
P.O. 5452,Addis
Box 5452, AddisAbaba,
Ababa,Ethiopia
Ethiopia
Tel: +251
Tel: + 251
11 11 5544334, 5544557/8
5544334
Mob:+251
Tel: +25111930109893
5544557/8
GENERAL INFORMATION Shelf Life 12 months from date of manufacture, if stored under Fax:+251
Fax: +2511111 5543610
5543610
Email:ethiopia@conmix.com
Email: ethiopia@conmix.com
www.conmix.com
www.conmix.com
warehouse conditions in original unopened packing.
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
Extreme temperature / humidity may reduce shelf life. product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
FitBond SBR
FitBond SBR
Styrene Butadiene Rubber Based Bonding Agent
STANDARDS ASTM C1059 Type II, ASTM C932 one minute. With the machine in operation, add the pre-mixed FitBond SBR and clean
water. Continue mixing for 3 minutes to ensure complete dispersal into the sand-cement
USES FitBond SBR is used as a bonding agent between old concrete and new concrete, mix. Make only small adjustments to the quantity of clean water but do not significantly
cementitious plasters, renders etc. It is used to increase water tightness of renders to be exceed the dosage shown below. Mix until homogenous material is obtained.
applied on internal and external walls, basements, swimming pools, water tanks,
tunnels, underpasses, sludge tanks etc. It is also used as an additive in mortars for repair GENERAL GUIDELINES Repair Mortars - Mix Proportions
of damaged concrete elements, bonding rush coat for plaster etc. Thickness 6-40 mm
10 Itr of FitBond SBR
ADVANTAGES • Improves tensile and flexural strength of cementitious mixes 8-12 Itrs of clean water (as per the required consistency)
• Helps in reducing attack of aggressive elements by reducing porosity 50 kgs of Ordinary Portland Cement
• Compatible with all types of cements 150 kgs of sand
• Prolonged corrosion protection and abrasion resistance Floor Screeds - Mix Proportions
• Reduces shrinkage Thickness: 30 mm-70 mm
• Suitable for internal and external applications in conjunction with cement 10 Itrs of FitBond SBR
• Non toxic 6-10 Itrs of clean water
50 kgs of Ordinary Portland Cement
100 kgs of fine aggregate
TYPICAL PROPERTIES at 25°C
50 kgs of 10 mm down aggregate
PROPERTY TEST METHOD VALUE The screed should be of earth moist consistency
Component - Single Renders - Mix Proportions
Form - Liquid Thickness: 6 mm-15 mm
Colour - Milky White 10 Itrs of FitBond SBR
Specific Gravity ASTM D1475 1.02 kg/ltr +/- 0.05 6 -10 ltrs of clean water
Compressive Strength BS 6319-2 10-15% increase over control 50 kgs of Ordinary Portland Cement
Flexural Strength BS 6319-3 5-10% increase over control 150 kgs of fine sand
Tensile Strength BS 6319-7 5-10% increase over control The render should be cohesive and of earth moist consistency
Tensile Bond Strength ASTM C932 > 1 N/mm² at 28 Days *Above proportions can vary as per site mix design requirements.
Pullout Strength ASTM D 4541 > 1 N/mm² at 28 Days
Slant Shear Bond Strength ASTM C1042 > 8.6 N/mm² at 28 Days APPLICATION As a Neat Bonding Agent: Stir FitBond SBR well and apply using brush, roller or spray
on the prepared surface. Ensure that the material is spread evenly on the entire surface.
SURFACE PREPARATION Surfaces should be clean, sound, free of dust, loose particles, grease, oil, etc. Residual Subsequent material to be bonded should be placed while FitBond SBR is still tacky.
primers from previous membrane systems and bitumen should be removed by suitable As a Bonding Slurry Coat: Apply slurry bonding coat made up of FitBond SBR, water
mechanical means. Absorbent surfaces should be saturated thoroughly with water. and cement in the ratio of 1:1:1 by weight using brush or roller.
Avoid ponding. Exposed rebar should be cleaned to a bright condition by grit or As an Additive: FitBond SBR modified mortars, toppings and renders must be well
sandblasting.
compacted on the prepared substrate by trowel. Exposed steel reinforcement should be
completely encapsulated by the mortar. FitBond SBR modified mortars can be applied
MIXING As a Bonding Slurry Coat: As per recommended dosage, add FitBond SBR to pre-
at a thickness of 6 mm to 40 mm. Where thick sections in excess of 40 mm are to be built-
measured quantity of water in a suitable container and stir well.
Add cement slowly and mix well using a slow speed drill machine fitted with a paddle. up, the surface of the intermediate layers should be keyed and primed.
TekniFloor Plus
FitBond SBR Abrasion Resistant Mineral Based Dry Shake Floor Hardener
CURING FitBond SBR modified cementitious systems should be cured just after initial setting DESCRIPTION TekniFloor Plus is a non-metallic floor hardener used to form monolithic, hardened
with water or with a suitable curing agent form JetCure range of curing compounds. concrete floors. It provides a hardened abrasion resistant surface and can also be used
to inhibit dust formation.
PACK SIZE 5 ltr, 15 Itr and 150 ltr
USES Used to provide a heavy duty concrete floor subject to heavy loads and traffic such as
COVERAGE As a neat bonding agent: 5-7 m²/1tr/coat . Actual coverage depends on texture and workshops, warehouses, carparks, garages, production areas, hospitals, schools,
porosity of substrate. As an additive for tile adhesives, bedding mortars, sand-cement commercial floors, shopping centers, loading bays, industrial complexes, etc.
renders, plasters and screeds, the dosage may vary from 10 to 20% by weight of
cement. ADVANTAGES • High abrasion resistance
• High impact resistance
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under • Increases the strength of concrete surface
warehouse conditions in original unopened packing. • Creates dense, easy to clean, dust free surfaces
Cleaning Clean all equipments and tools with water immediately after • Suitable for wet areas
APPLICATION Once the freshly poured and levelled concrete has reached its plastic state, the surface
should be smoothened using a mechanical trowel. After bleed water has evaporated and
concrete has a wet shine, sprinkle uniformly, two third of the recommended quantity of
TekniFloor Plus over the concrete. Allow applied material to absorb moisture from the
concrete surface. Using a wooden float, work the material into the concrete ensuring that
the material becomes an integral part of the surface. Broadcast the balance material,
allow the material to absorb moisture and then float with a wooden float. When the
surface is sufficiently firm enough to take the weight of power float, finish off by means of
a power trowel. Extra care should be taken while applying the floor hardener at bay
edges and joints.
Manufacturer:
Manufacturer:
LICON MANUFACTURING
LICON MANUFACTURING PLC.
PLC.
P.O.Box
P.O. 5452, Addis
Box 5452, AddisAbaba,
Ababa,Ethiopia
Ethiopia
Tel: +251
+ 2511111 5544334, 5544557/8
Tel:
Mob:+251
Tel:
5544334
+25111930109893
5544557/8
CURING TekniFloor Plus treated concrete must be protected to prevent premature moisture loss
Fax: +251
Fax: +25111115543610
5543610
Email: ethiopia@conmix.com
Email: ethiopia@conmix.com and crazing immediately after final finishing. Water cure by mist spray or by spreading
www.conmix.com
www.conmix.com
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the wet burlap/moist hessian over the surface. Alternatively suitable curing compound from
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in JetCure range maybe used.
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
ResiGard Primer SB
High Penetrating Epoxy Based
TekniFloor Plus Primer and Sealer
DESCRIPTION ResiGard Primer SB is a two component, low viscosity, solvent based epoxy resin
PACK SIZE 25 kg bag
priming system.
COVERAGE 2-3 kg/m² for Light traffic USES ResiGard Primer SB is used as a priming coat on cementitious and steel surfaces prior
3-4 kg/m² for Medium traffic to application of ResiGard range of coatings. Typical areas of application include
4-5 kg/m² for Heavy traffic carparks, factory floors, warehouses, etc.
use.
TYPICAL PROPERTIES at 25°C
HEALTH and SAFETY PPE's Gloves, goggles and suitable mask must be worn. PROPERTY TEST METHOD VALUE
Precautions Contact with skin, eyes, etc. must be avoided. If swallowed Component - Two: Part A - Base
TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the Service Temperature - +5°C to + 70°C
SURFACE PREPARATION Surface should be free from grease, oil, chemical contamination, dust, laitance, and
loose concrete. This can be achieved by shot blasting or light grinding to provide a sound
substrate and to allow penetration of the primer into the substrate. Steel surfaces should
be gritblasted to base metal. Surfaces which show any traces of oil must be degreased
with a chemical degreaser or hot air treatment prior to gritblasting.
MIXING ResiGard SB is supplied in two containers as pre-measured units. Stir base and
hardener component separately. Using a slow speed drill machine fitted with a paddle
mix both the components for at least 3 minutes to obtain a uniform mix. Part mixing
should be avoided.
Manufacturer:
Manufacturer:
LICON MANUFACTURING
LICON MANUFACTURING PLC.
PLC.
P.O.Box
P.O. 5452, Addis
Box 5452, AddisAbaba,
Ababa,Ethiopia
Ethiopia
Tel: +251
Tel: + 2511111 5544334, 5544557/8
5544334 APPLICATION Apply the material with a suitable squeegee, stiff nylon brush or roller working
Mob: +251 930109893
Tel: +251 11 5544557/8
Fax: +251
Fax: +25111115543610
5543610
Email: ethiopia@conmix.com
ethiopia@conmix.com
the ResiGard Primer SB into the substrate to ensure total absorption into any pinholes
Email:
www.conmix.com
www.conmix.com
and voids. Spray application is also possible. Airless spray will provide faster rate of
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the application.
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
ResiGard Primer SF
Solvent Free Epoxy Based Primer
ResiGard Primer SB and Coating System
PACK SIZE 6 Itr set, 15 ltr set DESCRIPTION ResiGard Primer SF is a two part, low viscosity, solvent free epoxy resin system.
7.5-9 m²/ltr/coat. Actual consumption depends on texture and porosity of substrate. USES ResiGard Primer SF is used as a priming coat on cementitious, wood and steel
COVERAGE
surfaces prior to application of ResiGard range of coatings. Typical areas of application
include carparks, factory floors, food industry, kitchens, aircraft hangers, hospitals,
LIMITATIONS When temperature exceeds 35°C, working times will be reduced significantly. During the
pharmaceutical plants, warehouses, etc. It can also be used as a clear coat to maintain
application in cold weather, correct conditioning is essential. Application should be
original colour and appearance of substrate which are not exposed to UV rays.
halted if the ambient or substrate temperature is likely to fall below 10°C.
SURFACE PREPARATION Surface should be free from grease, oil, chemical contamination, dust, laitance, and
loose concrete. This can be achieved by shot blasting or light grinding to provide a sound
substrate and to allow penetration of the primer into the substrate.
Steel surfaces should be gritblasted to base metal. Surfaces which show any traces of
oil must be degreased with a chemical degreaser or hot air treatment prior to gritblasting.
MIXING ResiGard Primer SF is supplied in two containers as pre-measured units. Stir base and
hardener component separately. Using a slow speed drill machine fitted with a paddle,
mix both the components for at least 3 minutes to obtain a uniform mix. Part mixing
48 CC/RG11/Ver7/07/14
CC/ET/RG11/Ver7/07/14 2/2 Technical Datasheet CC/ET/RG12/Ver6/07/14
CC/RG12/Ver6/07/14 1/2 Technical Datasheet 49
Construction Chemicals Construction Chemicals
ResiGard ES
Heavy Duty Abrasion and Chemical
ResiGard Primer SF Resistant Epoxy Floor Screed
PACK SIZE 6 ltr set, 15 ltr set DESCRIPTION ResiGard ES is a three component, solvent free, epoxy resin based heavy duty
chemical, abrasion and impact resistant floor screed. It is designed for trowel application
COVERAGE 6-7 m²/ltr/coat. Actual consumption depends on texture and porosity of substrate. in thickness of 3 mm and above.
LIMITATIONS When temperature exceeds 35°C, working times will be reduced significantly. During the USES ResiGard ES gives a tough, high abrasion, chemical and impact resistant topping. It is
application in cold weather, correct conditioning is essential. Application should be used as a screed for floorings where excellent mechanical properties with superior
abrasion and wear characteristics are required. It can be used for industrial floorings,
halted if the ambient or substrate temperature is likely to fall below 10°C.
warehouses, workshops, ramps, garages, airport maintenance areas, metal processing
and engineering units and areas subjected to heavy traffic. It can also be used as a
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
coving or patch repair product.
warehouse conditions in original unopened packing.
Extreme temperature / humidity may reduce shelf life.
ADVANTAGES • Excellent mechanical properties
Cleaning Clean all equipments and tools with Conmix Cleaner
• Can be over coated with epoxy or polyurethane coating
immediately after use.
• Excellent abrasion resistance and adhesion to most of the substrates
• Anti-skid finish / slip resistance
HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn. • Excellent resistance to impact
Precautions Contact with skin, eyes, etc. must be avoided. If swallowed • Excellent chemical resistance
seek medical attention immediately. • Early development of initial hardness minimizes down time
Hazard Regarded as hazardous for transportation. • 3 to 4 times stronger than typical concrete
Disposal Do not reuse containers. To be disposed off as per local • Good bond strength
rules and regulations.
Additional Information Refer MSDS. (Available on request.)
TYPICAL PROPERTIES at 25°C
TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the PROPERTY TEST METHOD VALUE
correct use of its products. Component - Three: Part A - Base
Part B- Hardener
Part C- Filler
Mixed Form - Mortar
Colour - Grey
Pot Life - 45 - 60 mins
Full Cure - 7 Days
Bond Strength ASTM D4541 > 2 N/mm²
Flexural Strength BS 6319-3 25 N/mm²
Compressive Strength BS 6319-2 85 N/mm²
Tensile Strength BS 6319-7 15 N/mm²
Chemical Resistance ASTM D543 Resistant to various chemicals like acids,
mild alkalis, fuels, grease, petrol, etc
Manufacturer:
Manufacturer:
LICON MANUFACTURING PLC.
CONMIX LTD.Addis Ababa, Ethiopia Application Temperature - +5°C to +40°C
P.O.Box 5452,
P.O.
Tel: Box 5936,
+ 251 11 Sharjah
5544334, 5544557/8
United Arab930109893
Mob: +251 Emirates Sales Office: Service Temperature - +5°C to + 70°C
Tel:
Fax: +971
+2516 11
5314155
5543610 Tel: +971 6 5682422
Fax: +971 6 5314332
Email: ethiopia@conmix.com Fax: +971 6 5681442
Email: conmix@conmix.com www.conmix.com
www.conmix.com
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
50 CC/RG12/Ver6/07/14
CC/ET/RG12/Ver6/07/14 2/2 Technical Datasheet CC/RG10/Ver6/07/14
CC/ET/RG10/Ver6/07/14 1/3 Technical Datasheet 51
Construction Chemicals Construction Chemicals
ResiGard SL2
1-3 mm Thick Self-Smoothening Chemical Resistant
High Performance Epoxy Flooring System
ResiGard ES
PACK SIZE 10 Itr set DESCRIPTION ResiGard SL2 is a four component, solvent free, epoxy resin, self-smoothening
chemical resistant flooring system. It provides excellent mechanical and chemical
COVERAGE 0.2 m²/ltr/ at 5 mm thickness resistance qualities.
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under USES ResiGard SL2 can be used for wide range of industrial environments where a lasting
warehouse conditions in original unopened packing. solution to floor maintenance problems is required. It is suitable for use in wet areas
Extreme temperature / humidity may reduce shelf life. where strict levels of hygiene and cleanliness are required or where chemicals are
Cleaning Clean all equipments and tools with Conmix Cleaner stored or manufactured. Ideal for use in food and chemical industry, hospitals, schools,
immediately after use. kitchens, laboratories, pharmaceutical industry, high traffic applications, industrial
manufacturing plants, garages, etc.
HEALTH and SAFETY PPE's Gloves, goggles and suitable mask must be worn.
Precautions Contact with skin, eyes, etc. must be avoided. If swallowed ADVANTAGES • Durable - high impact resistance
seek medical attention immediately. • Good resistance to a wide range of chemicals
Hazard Regarded as hazardous for transportation. • Hygienic - provides a dense, impervious, seamless floor surface which is easy to clean
Disposal Do not reuse containers. To be disposed off as per local
• High flow characteristics combined with an attractive, self-smoothening finish
rules and regulations.
• Solvent free and non-toxic
Additional lnformation Refer MSDS. (Available on request.)
• Phenol free, can also be used in food processing industry
TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the • Fast application - minimizes downtime
52 CC/RG10/Ver6/07/14
CC/ET/RG10/Ver6/07/14 3/3 Technical Datasheet CC/RG07/Ver7/07/14
CC/ET/RG07/Ver7/07/14 1/3 Technical Datasheet 53
Construction Chemicals Construction Chemicals
ResiGard SL4
3-6 mm Thick Self-Smoothening Chemical Resistant
High Performance Epoxy Flooring System
LIMITATIONS At higher temperatures pot life will be reduced. DESCRIPTION ResiGard SL4 is a four component, solvent free, epoxy resin, self-smoothening, heavy
For working in cold climates (<5°C) ResiGard SL2 containers need to be kept in a hot duty, chemical resistant, impact and abrasion resistant flooring system. It provides
water bath. excellent mechanical and chemical resistance and is available in aesthically pleasing
ResiGard SL2 cannot be applied in areas exposed to direct sunlight. colours.
PACK SIZE 7.5 ltr and 15 ltr set USES ResiGard SL4 is suitable for use in food and pharmaceutical industry where high levels
of hygiene and cleanliness are required. Due to its high chemical resistance property it
COVERAGE 7.5 m²/set of 7.5 ltr at 1 mm thickness is ideally suited for chemical industry, laboratories, etc. It is suitable for various floor
Actual Coverage rates may vary according to the substrate porosity and texture,
applications in light, medium and heavy industries.
wastage factors, site and application conditions, etc.
HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn. • Fast application - minimizes downtime
Precautions Contact with skin, eyes, etc. must be avoided. If swallowed • Available in a wide range of colours to enhance the working environment
seek medical attention immediately.
Hazard Regarded as hazardous for transportation. TYPICAL PROPERTIES at 25°C
Disposal Do not reuse containers. To be disposed off as per local
rules and regulations. PROPERTY TEST METHOD VALUE
Additional Information Refer MSDS. (Available on request.) Component - Four: Part A - Base
Part B- Hardener
TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the Part C- Filler
correct use of its products. Part D-Colour Pack
Mixed Form - Viscous Liquid
Colour - Various colours available
Pot Life ASTM D2471 45-60 mins
Recoat Time - 10-24 hrs
Full Cure - 7 days
Bond Strength ASTM D4541 > 2 N/mm² at 7 days
Flexural Strength BS 6319-3 30 N/mm² at 7 days
Compressive Strength BS 6319-2 75 N/mm² at 7 days
Tensile Strength BS 6319-7 17 N/mm² at 7 days
Chemical Resistance ASTM D543 Resistance to various chemicals like mild acids,
alkalis, fuels, grease, petrol, etc
Manufacturer: Application Temparature - +5°C to +40°C
Manufacturer:
LICON MANUFACTURING PLC.
CONMIX LTD.Addis Ababa, Ethiopia -
P.O.Box 5452,
P.O.
Tel: Box 5936,
+ 251 11 Sharjah
5544334, 5544557/8
Service Temparature +5°C to + 70°C
United Arab930109893
Mob: +251 Emirates Sales Office:
Tel:
Fax: +971
+2516 11
5314155
5543610 Tel: +971 6 5682422
Fax: +971 6 5314332
Email: ethiopia@conmix.com Fax: +971 6 5681442
Email: conmix@conmix.com www.conmix.com
www.conmix.com
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
54 CC/RG07/Ver7/07/14
CC/ET/RG07/Ver7/07/14 3/3 Technical Datasheet CC/RG08/Ver7/07/14
CC/ET/RG08/Ver7/07/14 1/3 Technical Datasheet 55
Construction Chemicals Construction Chemicals
ResiGard HP
High Performance Solvent Free
Epoxy Coating
ResiGard SL4
PACK SIZE 7.5 and 15 ltr set DESCRIPTION ResiGard HP is a four component, solvent-free, epoxy resin high build coating for
concrete and steel. It may be applied to produce either a smooth or rough finish
COVERAGE 2.5 m²/set of 7.5 ltr at 3 mm thickness incorporating anti-slip grains.
Actual Coverage rates may vary according to the substrate porosity and texture,
wastage factors, site and application conditions, etc.
USES ResiGard HP can be used as floor protection coating in various industries like
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under pharmaceutical, food and beverage, warehouses, bottling units, laboratories, hospitals,
warehouse conditions in original unopened packing. kitchens, wet areas, car parks, garages, industrial manufacturing plants, etc.
Extreme temperature / humidity may reduce shelf life.
Cleaning Clean all equipments and tools with Conmix Cleaner • Solvent free, no odour during application
ADVANTAGES
immediately after use.
• Seamless surface giving complete floor protection
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
ResiGard EC
High Performance, Chemical Resistant
Epoxy Coating
ResiGard HP
TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the DESCRIPTION ResiGard EC is a three component solvent based epoxy resin coating system for steel
and concrete surfaces. It cures to a semi-gloss, impervious finish.
correct use of its products.
USES ResiGard EC provides a hard, tough, easily cleanable and attractive floor coating in
areas where high resistance to chemical attack is required. It is suitable for use in
workshops, car parks, dairies, kitchens, showrooms, light to medium duty industrial floor
coatings, etc.
SURFACE PREPARATION Surfaces to be coated must be clean, dry, sound, free of mould release agents, bond
breaking coatings, curing compounds or any other form of contamination that may affect
the adhesion of the epoxy coating to the substrate. Surface preparation must be done
using appropriate methods like grinding or wire brushing and vacuumed. All loose
Manufacturer:
Manufacturer:
LICON MANUFACTURING PLC. concrete should be removed until a sound substrate is reached. Use suitable epoxy or
CONMIX LTD.Addis Ababa, Ethiopia
P.O.Box 5452,
P.O.
Tel: Box 5936,
+ 251 11 Sharjah
5544334, 5544557/8 cementitious repair mortar from ReCon range to rectify minor irregularities, cracks, etc.
United Arab930109893
Mob: +251 Emirates Sales Office:
Tel:
Fax: +971
+2516 11
5314155
5543610 Tel: +971 6 5682422 Where water curing is not feasible, use epoxy repair material ReCon FCE. New
Fax: +971 6 5314332
Email: ethiopia@conmix.com Fax: +971 6 5681442
Email: conmix@conmix.com www.conmix.com
www.conmix.com cementitious surfaces should be at least 28 days old and have a moisture content less
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the than 5% prior to application
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
58 CC/RG06/Ver7/04/14
CC/ET/RG06/Ver7/07/14 4/4 Technical Datasheet CC/RG04/Ver6/07/14
CC/ET/RG04/Ver6/07/14
1/3 Technical Datasheet 59
Construction Chemicals Construction Chemicals
MoyaProof CWL
ResiGard EC Liquid Waterproofing System by Crystallization
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
DESCRIPTION MoyaProof CWL is a single component liquid waterproofing system by crystallization
warehouse conditions in original unopened packing. method. It penetrates into the micropores and fine capillaries inside the concrete. It
Extreme temperature / humidity may reduce shelf life. reacts with the cement matrix to form insoluble inorganic complex ion crystals. As long
Cleaning Clean all equipments and tools with Conmix Cleaner as moisture is present, MoyaProof CWL remains active and will seal hairline cracks
immediately after use. both present and future.
USES MoyaProof CWL is a new generation waterproofing system specially for aggressive
HEALTH and SAFETY PPE's Gloves, goggles and suitable mask must be worn.
environment for below and above grade applications. It can be used for various
Precautions Contact with skin, eyes, etc. must be avoided. If swallowed
applications in concrete structures including marine and coastal structures, rafts,
seek medical attention immediately.
precast panels, water storage tanks, highways, runways, roofs, decks, bridges, cut and
Hazard Regarded as hazardous for transportation.
cover tunnels, silos, car parks, swimming pools, pipes, lift pits, etc.
Disposal Do not reuse containers. To be disposed off as per local
rules and regulations. ADVANTAGES • Penetrates deep into the concrete
Additional lnformation Refer MSDS. (Available on request.) • Very good impermeability
• Produces dense and durable concrete
TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the • Reduces chloride and sulphate penetration
correct use of its products. • Prevents corrosion in structures
• Non-toxic and eco-friendly
• UV resistant, no topping or protection required, can be overcoated
• Cannot be damaged, no debond as it is a subsurface membrane
• Suitable for use in contact with potable water
• Remains active through out the life of concrete
• No protection boards required when backfilling
• Reseals hairline cracks (self healing) on contact with moisture
• Can be used with concrete containing PFA, GBFS, or Silica fume
• Increases useful life of structure
• Increases concrete’s hardness
Component - Single
Form - Liquid
Appearance - Clear to Opaque
Specific Gravity ASTM D1475 1.10 +/- 0.05
Toxicity BS 6920-1 Non-Toxic
pH BS 1377-3 11-12
Drying Time ASTM D2939 Minimum 2 hrs
Manufacturer: Recoat Time - 5-6 hrs
Manufacturer:
LICON MANUFACTURING PLC.
CONMIX LTD.Addis Ababa, Ethiopia
P.O.Box 5452, Impact test ASTM C805 15-20% increase over untreated surface
P.O.
Tel: Box 5936,
+ 251 11 Sharjah
5544334, 5544557/8
United Arab930109893
Emirates Sales Office:
Mob: +251
Tel: Water Permeability BSEN 12390-8 > 80% improvement over control
Fax: +971
+2516 11
5314155
5543610 Tel: +971 6 5682422
Fax: +971 6 5314332
Email: ethiopia@conmix.com Fax: +971 6 5681442
Email: conmix@conmix.com www.conmix.com
www.conmix.com
*Result of the test carried out is based on a particular concrete mix.
Contact Conmix technical team for more information.
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
60 CC/RG04/Ver6/07/14
CC/ET/RG04/Ver6/07/14 3/3 Technical Datasheet CC/ET/MP01/Ver5/01/14 1/3 Technical Datasheet 61
Construction Chemicals Construction Chemicals
SURFACE PREPARATION Concrete surfaces to be treated must be clean and free of laitance, dirt, films, paint, HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
coatings or other foreign matter. The surfaces must also have an open capillary system Precautions Contact with skin, eyes, etc. must be avoided. If swallowed
for the MoyaProof CWL treatment. If surfaces are too smooth the concrete should be seek medical attention immediately.
acid etched, lightly sandblasted or waterblasted. Structural defects such as cracks,
Hazard Regarded as non-hazardous for transportation.
faulty construction joints and honeycombs should be routed out to sound concrete and
Disposal Do not reuse containers. To be disposed off as per local
repaired. MoyaProof CWL is not designed for use in expansion joints or “moving”
rules and regulations.
cracks. Horizontal surfaces should preferably have a rough wood float or broom finish.
Additional Information Refer MSDS. (Available on request.)
APPLICATION MoyaProof CWL should be applied after two to four weeks of pouring the concrete or
any time later. It is effective especially on old concrete. TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the
MoyaProof CWL may be applied to concrete immediately after forms are stripped correct use of its products.
acting as a curing compound and sealing material. MoyaProof CWL can be applied by
spray, brush or roller. For optimum results on horizontal concrete surfaces, it is
recommended that MoyaProof CWL be flooded over the concrete. For vertical
surfaces, spray application is recomended. Apply with low pressure spray and allow to
dry for 5-6 hours before applying the second coat. Concrete surface must be dry, 24 hrs
before application of MoyaProof CWL. Sealing of joints etc., should be carried out
before application.In below ground level concrete surface applications, ensure that the
concrete surfaces are dry before application. If high hydrostatic pressures are
anticipated, apply a coat of MoyaProof CWP over the MoyaProof CWL. MoyaProof
CWP should be cured by keeping moist for 12-14 days after application.
CURING Water is necessary for curing which facilitates reaction of MoyaProof CWL. Curing
should be done by placing wet hessian over the applied area for a minimum period of 5-7
days. Mist spray curing with water can also be carried out.
LIMITATIONS MoyaProof CWL should not come in contact with glass, precoated surface like paints,
curing compounds etc. MoyaProof CWL should not be applied at temperatures below
5°C. Do not flood too much of water on the applied surface for initial 4-5 days.
COVERAGE 5 m²/ltr/coat
Actual coverage depends on porosity and texture of the substrate.
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
Manufacturer:
Manufacturer:
warehouse conditions in original unopened packing. LICON MANUFACTURING
LICON MANUFACTURING PLC.
PLC.
P.O.Box
P.O. 5452, Addis
Box 5452, AddisAbaba,
Ababa,Ethiopia
Ethiopia
Extreme temperature / humidity may reduce shelf life. Tel: +251
Tel: + 2511111 5544334, 5544557/8
5544334
Mob:+251
Tel: +25111930109893
5544557/8
Fax: +251
+25111115543610
5543610
MoyaProof CWL should be stored above 15°C to avoid Fax:
Email: ethiopia@conmix.com
Email: ethiopia@conmix.com
www.conmix.com
www.conmix.com
haziness.
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
Cleaning Clean all equipments and tools with water immediately after product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
use. good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
MoyaProof CWP
Cementitious Slurry Waterproofing
System by Crystallization MoyaProof CWP
DESCRIPTION MoyaProof CWP is a cementitious slurry waterproofing system by crystallization. The MIXING Mix one bag of 20 kg with 10.5-11.2 ltrs of clean water. Always add powder to water, mix
active chemicals in the applied MoyaProof CWP reacts with the free lime and moisture using a slow speed drill fitted with a paddle until a smooth and lump free consistency is
present in the capillary track of the concrete to form an insoluble crystalline complex. obtained. Do not rework stiff material by adding more water. Only mix sufficient quantity
These crystals block the capilaries and minor shrinkage cracks in the concrete to of material that can be used within 30 minutes.
prevent any further water ingress.
APPLICATION Slurry coat: Apply MoyaProof CWP with a stiff fiber brush. Scrub well into the damp
USES MoyaProof CWP can be used for various concrete elements in structures such as
surface, filling all pores and finish with final strokes in one direction. After the first coat has
marine and coastal structures, rafts, precast panels, water storage tanks, highways,
set but while it is still green, apply a second coat. If this is not possible, pre wet first coat
runways, roofs, decks, bridges, cut and cover tunnels, silos, carparks, swimming pools,
before application of the second coat. Application is recommended on concrete that is at
pipes, lift pits, etc.
least two to four weeks old.
ADVANTAGES • Suitable for use in contact with potable water Dry Shake Method: For Newly Poured Concrete, use MoyaProof CWP directly from the
• Chemicals remain dormant and are reactivated whenever there is a presence of bag. Distribute the powder evenly over freshly poured concrete at a spread rate of 4-5
moisture kg/m² before the final trowelling. It is recommended to distribute approximately 50% of
• Time saving, fast tracks projects the powder in one direction with the remaining 50% at right angles to the first application.
• Can be applied to freshly laid green concrete by dry shake method Release the powder as close to the wet surface of concrete as possible. Finally trowel
• Can be applied on the negative side of water retaining or underground structures the concrete to the required finish.For positive side waterproofing, MoyaProof CWP can
• Does not require protection from backfill be sprinkled on horizontal formwork. Concrete should be poured directly on the well
• Economical to apply spread material.
Leaking Cracks: MoyaProof CWP can be mixed to dry mortar consistency and used to
TYPICAL PROPERTIES at 25°C fill the cracks. If there is any active water leakage then MoyaProof CWP can be mixed
with MoyaProof Plug in the ratio 1:1 and fixed at the point of water leakage to stop the
PROPERTY TEST METHOD VALUE flow of water. Over such treatment, two coats of MoyaProof CWP can be applied at the
Component - Single said rate of application.
Form - Powder
Colour - Grey OVERCOATING MoyaProof CWP treated surfaces to receive epoxy coating or to be painted must be
Toxicity BS 6920-1 Non-Toxic neutralized by using buffer solution. Alternatively, after a minimum period of 21 days of
pH BS 1377-3 11-12 application, the applied MoyaProof CWP should be removed by suitable mechanical
Drying Time ASTM D2939 1hr means. Any type of coating can be applied on such surface.
Recoat Time - 2-4 hrs
Water Permeability BSEN 12390-8 > 80% improvement over control* CURING Applied MoyaProof CWP should be protected against moisture evaporation by sun and
Chloride Content BSEN 480-10 Nil to BSEN 934-2 wind. Careful fog/mist spraying of water should be undertaken to keep the surface damp.
Alternatively the surface can be covered with, wet hessian or moist sand. Curing
*Result of the test carried out is based on a particular concrete mix.
Contact Conmix technical team for more information. compounds are not recommended.
Moisture cure MoyaProof CWP treated surfaces 3-4 times per day for a period of 5-7
days. Backfill material can be placed on MoyaProof CWP applications after moisture
SURFACE PREPARATION Concrete surfaces to be treated must be clean and free of laitance, dirt, films, paint,
curing has been completed. No protection boards are required.
coatings or other foreign matter. The surfaces must also have an open capillary system for
the MoyaProof CWP treatment. If surfaces are too smooth the concrete should be acid
etched, lightly sandblasted or waterblasted. Structural defects such as cracks, faulty LIMITATIONS MoyaProof CWP should not be applied on dry surfaces.
construction joints and honeycombs should be routed out to sound concrete and
repaired. MoyaProof CWP is not designed for use in expansion joints or “moving” cracks. PACK SIZE 20 kg
Horizontal surfaces should preferably have a rough wooden float or broom finish. All
surfaces should be saturated with water prior to application.
MoyaProof WS2
Polymer Modified Semi Flexible Cementitious
MoyaProof CWP Waterproofing Membrane
YIELD 17.7 ltr/bag DESCRIPTION MoyaProof WS2 is a two component, acrylic co-polymer based flexible cementitious
waterproofing system.
COVERAGE Dry Shake method : 4-5 kg/m²
Slurry : 8.86 m²/bag at 2 mm thickness. USES MoyaProof WS2 is suitable for many waterproofing applications, such as swimming
pools, balconies, bathrooms, wet areas, basements, roof waterproofing system in damp
Actual coverage depends on porosity and texture of the substrate.
conditions where other systems cannot be used, lift pits, etc. It can also be used as a
backing coat for marble, stone and other mineral based cladding to protect against
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
rising moisture.
warehouse conditions in original unopened packing.
Extreme temperature / humidity may reduce shelf life.
ADVANTAGES • Can be applied to freshly hardened concrete
Cleaning Clean all equipments and tools with water immediately after
• Excellent elongation and flexibility
use.
• Non-toxic, suitable for use in potable water tanks
• Protection against carbonation and chlorides
HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
• Breathable coating
Precautions Contact with skin, eyes, etc. must be avoided.
• Excellent adhesion
Hazard Regarded as non-hazardous for transportation. • Easy to apply
Disposal Do not reuse bags. To be disposed off as per local rules and • Increased frost and salt resistance
regulations. • Excellent for damp proofing basements
Additional Information Refer MSDS. (Available on request.) • Exhibits crack bridging and sealing property
TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the TYPICAL PROPERTIES at 25°C
correct use of its products.
PROPERTY TEST METHOD VALUE
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
SURFACE PREPARATION Surface should be clean and sound, free of dust, loose particles, grease, oil,
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
primers from previous membrane systems or bitumen. Bitumen or primers should be Precautions Contact with skin, eyes, etc. must be avoided.
removed by shotblasting or mechanical means. Spalled concrete should be repaired by Hazard Regarded as non-hazardous for transportation.
cutting to sound concrete and patching with ReCon GP.
Disposal Do not reuse bags. To be disposed off as per local rules and
Special recommendations for critical areas of application: regulations.
It is recommended to use Conmix ConTape at all critical areas such as intersections, Additional Information Refer MSDS. (Available on request.)
corner joints, floor/wall junctions, gaps, peripherial areas of pipelines before the
application of MoyaProof WS2. Before fixing Conmix ConTape, the gaps and corners
TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the
should be filled and levelled with polymer modified mortar ReCon GP.
correct use of its products.
MIXING MoyaProof WS2 is supplied in pre-measured units. Slowly add powder to the liquid and
using a slow speed drill machine fitted with a paddle, mix to a lump free smooth
consistency. Do not rework a stiffened mix by adding more water. Only mix sufficient
quantity of material that can be used within 30-40 minutes.
APPLICATION Saturate the concrete surface with clean water. Apply the first coat while the surface is
still damp with no free standing water. Apply using a short stiff bristle brush or roller at a
minimum thickness of 1 mm per coat. After 2-6 hours, apply the second coat in
perpendicular direction to the first coat. The second coat can be finished by rubbing
down with a soft sponge. Spray or trowel application is acceptable provided the mixing
ratio is adjusted to achieve the right consistency. It is recommended that for application
over hollow blocks or highly porous areas, a minimum of 3 coats to total thickness of 3
mm be applied.
CURING MoyaProof WS2 should be protected from high wind, direct sunshine and rain until fully
cured. Keep the treated area moist for 3-4 days after application.
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
warehouse conditions in original unopened packing.
Manufacturer:
Manufacturer:
Extreme temperature / humidity may reduce shelf life. LICON MANUFACTURING
LICON MANUFACTURING PLC.
PLC.
P.O.Box
P.O. 5452, Addis
Box 5452, AddisAbaba,
Ababa,Ethiopia
Ethiopia
Cleaning Clean all equipments and tools with water immediately after Tel: +251
Tel: + 2511111 5544334, 5544557/8
5544334
Mob:+251
Tel: +25111930109893
5544557/8
use. Fax: +251
Fax: +25111115543610
5543610
Email: ethiopia@conmix.com
Email: ethiopia@conmix.com
www.conmix.com
www.conmix.com
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn. product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
MoyaShield WR
Water Dispersed Silane Siloxane Based
Impregnating Water Repellent MoyaShield WR
DESCRIPTION MoyaShield WR is a clear silane siloxane based water repellent sealer that penetrates down keeping a wet edge at all times. Finish at the base, work well into edges. Use a soft,
into the substrate and provides water repellency by reacting with the substrate. It has a
dry cloth to remove any excess solution left on the surface. Second coat may be applied
micro molecular structure that helps to achieve deep penetration inhibiting water ingress
immediately. Allow the applied material to dry for at least 24 hours, before subjecting the
into the substrate.
surface to water.
USES MoyaShield WR is used as a clear coat to protect concrete surfaces, stone cladding,
coloured plasters, parking decks, bridges, decorative renders, tiles, tile grouts, etc. LIMITATIONS MoyaShield WR is not recommended for surfaces subject to hydrostatic pressure.It is
advisable to protect the shower screen, glass and any painted areas against splashes of
ADVANTAGES • Deep penetrating sealer
MoyaShield WR. If splashed, clean with water immediately.
• Reduces water and chloride intrusion
• Non-staining
• Ready to use and easy to apply PACK SIZE 20 ltr
• Chemically resistant to fuels, atmospheric contaminants and oils
• Significantly reduces absorption of water
COVERAGE 5 m²/ltr/coat
• Breathable
• Helps to prevent efflorescence Actual coverage depends on porosity and texture of the substrate.
• Resistant to UV light
• No fire hazard during application
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
• Long term effectiveness
• Eco friendly, can be applied in enclosed areas warehouse conditions in original unopened packing.
Extreme temperature / humidity may reduce shelf life.
TYPICAL PROPERTIES at 25°C Cleaning Clean all equipments and tools with water immediately after
use.
PROPERTY TEST METHOD VALUE
Component - Single
Liquid HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
Form -
Colour - Clear Precautions Contact with skin, eyes, etc. must be avoided. If swallowed
Recoat Time - Should be applied immediately Disposal Do not reuse containers. To be disposed off as per local
- (wet on wet)
rules and regulations.
Application Temperature - +5°C to +40°C Additional Information Refer MSDS. (Available on request.)
*Depends on substrate porosity
TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the
SURFACE PREPARATION Before application of MoyaShield WR, it is important to ensure that the surface is clean
correct use of its products.
and free from dust, loose material and dampness. It has to be applied on completely dry
surface. All contaminants such as oil, grease or any surface contamination must be
removed to ensure adequate penetration when the product is applied. Surfaces that Manufacturer:
Manufacturer:
LICON MANUFACTURING
LICON MANUFACTURING PLC.
PLC.
have been cleaned with water must be allowed to dry out completely before application. P.O.Box
P.O. 5452, Addis
Box 5452, AddisAbaba,
Ababa,Ethiopia
Ethiopia
Tel: +251
Tel: + 2511111 5544334, 5544557/8
5544334
Mob:+251
Tel: +25111930109893
5544557/8
Cracked or damaged areas must be repaired using ReCon range of repair products. Fax: +251
Fax: +25111115543610
5543610
Email: ethiopia@conmix.com
Email: ethiopia@conmix.com
www.conmix.com
www.conmix.com
APPLICATION MoyaShield WR should be applied by spraying or brushing. Apply from top and work It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
MegaFlow SP4
High Range Water Reducing and Set Retarding
Concrete Admixture MegaFlow SP4
DESCRIPTION MegaFlow SP4 is a high range water reducing admixture specifically designed for PACK SIZE 15 ltr and 200 ltr
producing high slump, flowing concrete in hot climates. It is based on selected
sulphonated napthalene polymers and is a powerful de-flocculent.
DISPENSING MegaFlow SP4 should be dispensed into the concrete mixer together with the mixing
water.
STANDARDS ASTM C494, Type B, D and G, BSEN 934-2.
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
USES MegaFlow SP4 can be used for various concrete applications. Recommended for large
concrete pours and where higher slump retention is needed. A significant water reducing warehouse conditions in original unopened packing.
agent and promotes strength gain at all ages of concrete. Extreme temperature / humidity may reduce shelf life.
Cleaning Clean all equipments and tools with water immediately after
ADVANTAGES • High slump concrete for congested areas use.
• Good workability retention
• Increases durability by reducing permeability
HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
• Water reduction of more than 20%
Precautions Contact with skin, eyes, etc. must be avoided. If swallowed
• No excessive air entrainment
seek medical attention immediately.
• Chloride free and safe for use in pre-stressed and reinforced concrete.
Hazard Regarded as non-hazardous for transportation.
TYPICAL PROPERTIES at 25°C Disposal Do not reuse containers. To be disposed off as per local
Specific Gravity ASTM C494 1.20 +/- 0.02 correct use of its products.
Air Entrainment ASTM C231 Up to 1% over control mix
Chloride Content BSEN 480-10 Nil to BSEN 934-2
pH ASTM C494 7-9
COMPATIBILITY MegaFlow SP4 can be used with all types of cements and cementitious material like fly
ash, GGBS, micro silica, etc. MegaFlow SP4 should not be premixed with other
admixtures.
DOSAGE Recommended dosage is 0.5 - 3.0% by weight of cementitious material. Higher dosage
can be used after verification of performance by conducting lab and site trials.
EFFECT OF OVERDOSING Overdosing may result in higher workability and delay in setting. If intentionally or
Manufacturer:
Manufacturer:
accidentally, dosage used is above the recommended limit, ensure that the stripping time LICON MANUFACTURING
LICON MANUFACTURING PLC.
PLC.
P.O.Box
P.O. 5452, Addis
Box 5452, AddisAbaba,
Ababa,Ethiopia
Ethiopia
of formwork is extended accordingly. In such cases, provided the concrete is properly Tel: +251
Tel: + 251
Mob:+251
1111 5544334, 5544557/8
5544334
+25111930109893
Tel: 5544557/8
Fax: +251
Fax: +25111115543610
5543610
cured, the ultimate strength will generally be higher than the regular concrete. The effects of Email: ethiopia@conmix.com
Email: ethiopia@conmix.com
www.conmix.com
www.conmix.com
overdosing are increased when sulphate resistant cement is used in the concrete mixes
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
because of the chemical nature of the cement as compared to that of OPC. product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
MegaFlow SP1
High Range Water Reducing Superplasticiser MegaFlow SP1
DESCRIPTION MegaFlow SP1 is a highly effective water reducing superplasticiser and an extremely is properly cured, the ultimate strength will generally be higher than the regular
concrete.
powerful de-flocculating agent based on soluble salt of polymericnapthalene
sulphonate. PACK SIZE 15 ltr and 200 ltr
STANDARDS ASTM C494, Type F, BSEN 934-2 DISPENSING MegaFlow SP1 should be dispensed into the concrete mixer together with the mixing
water.
USES It is used to produce flowing concrete for the congested areas, slabs, foundations, large
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
pours, beams, columns and precast elements. It provides excellent strength gain at warehouse conditions in original unopened packing.
early ages and major increase at all ages of concrete. Extreme temperature / humidity may reduce shelf life.
Cleaning Clean all equipments and tools with water immediately after
use.
ADVANTAGES • Good workability with fast strength gain
• Economical and cost effective solution for precast concrete
HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
• Increases durability by reducing permeability Precautions Contact with skin, eyes, etc. must be avoided. If swallowed
• Increased production in precast yards seek medical attention immediately.
• Normal setting without any retardation Hazard Regarded as non-hazardous for transportation.
Disposal Do not reuse containers. To be disposed off as per local
• Chloride free and safe for use in pre-stressed and reinforced concrete
rules and regulations.
Additional Information Refer MSDS. (Available on request.)
TYPICAL PROPERTIES at 25°C
TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the
PROPERTY TEST METHOD VALUE correct use of its products.
Component - Single
Form - Liquid
Colour - Brown
Specific Gravity ASTM C494 1.20 +/- 0.02
Air Entrainment - Up to 1% over Control mix
Chloride Content BSEN 480-10 Nil to BSEN 934-2
pH ASTM C494 7-9
COMPATIBILITY MegaFlow SP1 can be used with all types of cements and cementitious materials like fly
ash, GGBS, micro silica, etc. MegaFlow SP1 should not be premixed with other
admixtures.
DOSAGE Recommended dosage is 0.5 - 3.0% by weight of cementitious material. Higher dosage
can be used after verification of performance by conducting lab and site trials. Optimum
dosage of MegaFlow SP1 and effect on concrete properties such as workability,
strength, setting time, etc. are best assessed after preliminary tests on site using the Manufacturer:
Manufacturer:
LICON MANUFACTURING
LICON MANUFACTURING PLC.
PLC.
P.O.Box 5452, Addis
AddisAbaba,
Ababa,Ethiopia
Ethiopia
actual materials of mixes under consideration. P.O.
Tel:
Box 5452,
Tel: +251
+ 2511111 5544334, 5544557/8
5544334
Mob:+251
Tel: +25111930109893
5544557/8
Fax: +251
Fax: +25111115543610
5543610
Email: ethiopia@conmix.com
Email: ethiopia@conmix.com
EFFECT OF OVERDOSING Overdosing may result in higher workability and delay in setting. If intentionally or www.conmix.com
www.conmix.com
accidentally increased above the recommended limit, ensure that the stripping time of It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
formwork is extended accordingly. In such cases, provided the concrete products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
MegaFlow R
Mortar and Concrete Retarding Admixture MegaFlow R
DESCRIPTION MegaFlow R is retarding liquid admixture for concrete and mortars. MegaFlow R is DISPENSING MegaFlow R should be dispensed into the concrete / mortar mixer together with the
mixing water.
formulated from carefully selected raw materials and is manufactured under controlled
conditions to give a consistent product. It is based on a high grade plasticising and
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
retarding agent.
warehouse conditions in original unopened packing.
Extreme temperature / humidity may reduce shelf life.
STANDARDS BSEN 934-3 Cleaning Clean all equipments and tools with water immediately after
use.
USES MegaFlow R is used to produce workable and retarding concrete, plasters, renders and
mortars including all types of RMC’s, tunnels, runways, canals, reservoirs and marine HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
structures, etc. Precautions Contact with skin, eyes, etc. must be avoided. If swallowed
seek medical attention immediately.
ADVANTAGES • Excellent workablity retention Hazard Regarded as non-hazardous for transportation.
Disposal Do not reuse containers. To be disposed off as per local
• Good workability improvement to most of concrete / mortar mixes
rules and regulations.
• Ultimate strength enhancement
Additional Information Refer MSDS. (Available on request.)
• Can be used for pumpable concrete
• Extended setting time in high temperatures TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the
• Reduced shrinkage and creep correct use of its products.
Component - Single
Form - Liquid
Colour - Brown
Specific Gravity ASTM C494 1.22 +/- 0.02
Air Entrainment ASTM C231 Up to 1% over Control mix
Chloride Content BSEN 480-10 Nil to BSEN 934-2
pH ASTM C494 7-9
COMPATIBILITY MegaFlow R can be used with all types of cements and cementitious materials like fly
ash, micro silica, etc. MegaFlow R should not be premixed with other admixtures.
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
PACK SIZE 20 ltr and 200 ltr product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
MegaAir
Air Entraining, Plasticising Concrete
and Mortar Admixture MegaAir
DESCRIPTION MegaAir is a liquid air entraining admixture that is chloride-ion free and is based on DISPENSING MegaAir should be directly dispensed into the concrete mixer along with the mixing
water.
specially formulated surfactants. It can be used in concrete and mortar mixes.
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
STANDARD BSEN 934-3, ASTM C260
warehouse conditions in original unopened packing.
Extreme temperature / humidity may reduce shelf life.
USES MegaAir is used to improve the workability, cohesion and durability of concrete and Cleaning Clean all equipments and tools with water immediately after
mortar by the entrainment of microscopic air bubbles of controlled size and spacing, use.
uniformly distributed throughout the mix, reducing surface scaling and concrete failures.
It is used to produce concrete/mortars resistant to attack by frost and deicing salts, light HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
weight foam concrete etc. Precautions Contact with skin, eyes, etc. must be avoided. If swallowed
seek medical attention immediately.
ADVANTAGES • Protects against freezing and thawing Hazard Regarded as non-hazardous for transportation.
Disposal Do not reuse containers. To be disposed off as per local
• Improves permeability
rules and regulations.
• Improves workability
Additional Information Refer MSDS. (Available on request.)
• Improves durability
• Increases cohesion of mixes TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the
• Volume yield of concrete and mortar is increased correct use of its products.
• Improves harsh mixes
• Highly effective for mixes containing dusty aggregates
Component - Single
Form - Liquid
Colour - Brown
Specific Gravity ASTM C494 1.02 +/- 0.02
Chloride Content BS EN 480-10 Nil to BS EN 934-2
pH ASTM C494 7-9
COMPATIBILITY MegaAir can be used with all types of cements and cementitious materials like fly ash,
GGBS, micro silica, etc.
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
PACK SIZE 20 ltr product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
MegaAdd SAP
Shotcrete Accelerating Powder Admixture MegaAdd SAP
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored
DESCRIPTION MegaAdd SAP is a rapid set accelerator in powder form.
under warehouse conditions in original unopened packing.
Extreme temperature / humidity may reduce shelf life.
Cleaning Clean all equipments and tools with water immediately after
STANDARDS ASTM C1141-01, Grade 9, Class B
use.
USES MegaAdd SAP is used as an additive in cementitious mixes to enable rapid setting of HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
sprayed concrete and gunite for tunnel lining, water bodies, dams, swimming pools, Precautions Contact with skin, eyes, etc. must be avoided.
basement retaining walls, concrete repairs, etc. Hazard Regarded as non-hazardous for transportation.
Disposal Do not reuse bags. To be disposed off as per local rules and
regulations.
ADVANTAGES • Rapid setting Additional Information Refer MSDS. (Available on request.)
• Reduces the rebound loss and dust
• Imparts high early strength, improved water tightness TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the
• Fast build-up of multiple layers especially in overhead work correct use of its products.
• Chloride free
Component - Single
Form - Powder
Colour - Off White
Bulk Density - 0.75 gm/cc +/- 0.05
Chloride Content BSEN 480-10 Nil to BSEN 934-2
COMPATIBILITY MegaAdd SAP can be used with all types of cements and cementitious materials like
GGBS, fly ash, micro silica, etc.
EFFECT OF OVERDOSING Overdosing may result in very fast setting of cementitious mixes but will not affect other
properties.
PACK SIZE 20 kg
15 Kg
Manufacturer:
Manufacturer:
LICON MANUFACTURING
LICON MANUFACTURING PLC.
PLC.
P.O.Box
P.O. 5452, Addis
Box 5452, AddisAbaba,
Ababa,Ethiopia
Ethiopia
Tel: +251
Tel: + 2511111 5544334, 5544557/8
5544334
DISPENSING MegaAdd SAP should be directly mixed with the pre-mixed sand, cement and Mob:+251
Tel: +25111930109893
5544557/8
Fax: +251
Fax: +25111115543610
5543610
aggregates before addition of water. Email: ethiopia@conmix.com
Email: ethiopia@conmix.com
www.conmix.com
www.conmix.com
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
MegaFlow SP103
High Range Water Reducing and
Accelerating Superplasticiser MegaFlow SP103
DESCRIPTION MegaFlow SP103 is a very effective, high range water reducing, accelerating PACK SIZE 20 ltr, 200 ltr, 1000 ltr and bulk
superplasticiser and an extremely powerful de-flocculating agent. It is based on
polymeric sulphonate napthalene. DISPENSING MegaFlow SP103 should be dispensed into the concrete mixer together with the mixing
water.
STANDARDS ASTM C494, Type E; BSEN 934-2
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
USES Uses include to produce high slump concrete for the precast industries and other types warehouse conditions in original unopened packing.
of concrete elements like beams, columns, slabs etc. MegaFlow SP103 is to be used Extreme temperature / humidity may reduce shelf life.
Cleaning Clean all equipments and tools with water immediately after
where substantial water reductions are required to provide high early and ultimate
use.
strengths i.e. precast factories, prestressed concrete bridges, shotcreting, etc.
HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
ADVANTAGES • Water reduction more than 30%
Precautions Contact with skin, eyes, etc. must be avoided. If swallowed
• Increased production speed at precast yards seek medical attention immediately.
• Quick hardening of concrete in initial stages Hazard Regarded as non-hazardous for transportation.
• Extremely useful for concrete in cold climate Disposal Do not reuse containers. To be disposed off as
• Increases durability by reducing permeability per local rules and regulations.
• Improved waterborne salt resistance Additional Information Refer MSDS. (Available on request.)
• Chloride free and safe for use in prestressed and reinforced concrete
TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the
correct use of its products.
TYPICAL PROPERTIES at 25°C
Component - Single
Form - Liquid
Colour - Brown
Specific Gravity ASTM C494 1.21 +/- 0.02
Air Entrainment ASTM C231 Up to 1% over control mix
Chloride Content BSEN 480-10 Nil to BSEN 934-2
pH ASTM C494 7-9
COMPATIBILITY MegaFlow SP103 can be used with all types of cements and cementitious materials like
fly ash, GGBS, micro silica, etc. MegaFlow SP103 should not be premixed with other
admixtures.
82 CC/MF11/Ver6/07/14
CC/ET/MF11/Ver6/07/14 1/2 Technical Datasheet CC/MF11/Ver6/07/14
CC/ET/MF11/Ver6/07/14 2/2 Technical Datasheet 83
Construction Chemicals Construction Chemicals
MegaFlow P4
Water Reducing and Set Retarding
Plasticising Admixture MegaFlow P4
DESCRIPTION MegaFlow P4 is liquid, plasticising, water reducing and retarding concrete admixture
PACK SIZE 20 ltr, 200 ltr, 1000 ltr and Bulk
based on a high grade modified lignosulphonic acid derivative.
MegaFlow P4 is formulated from carefully selected raw materials and is manufactured
under controlled conditions to give a consistent product. DISPENSING MegaFlow P4 should be directly dispensed into the concrete mixer together with the
mixing water.
STANDARDS ASTM C494, Type B and D, BSEN 934-2
GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
USES MegaFlow P4 is used to produce easily workable and dense concrete for all types of
ready-mixed concrete, tunnels, runways, canals, reservoirs and marine structures, etc. warehouse conditions in original unopened packing.
It can also be used as waterproofer to reduce permeability of concrete. Extreme temperature / humidity may reduce shelf life.
Cleaning Clean all equipments and tools with water immediately after
ADVANTAGES • Good slump retention even at higher temperatures
use.
• Good workability improvement to most of concrete mixes
• Increases strength due to water reduction
• Effective in achieving cement reduction HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
• Durable concrete may be achieved Precautions Contact with skin, eyes, etc. must be avoided. If swallowed
• Extended setting time at high temperatures
seek medical attention immediately.
COMPATIBILITY MegaFlow P4 can be used with all types of cements and cementitious materials like fly
ash, GGBS, micro silica,etc. MegaFlow P4 should not be premixed with other
admixtures.
DOSAGE Recommended dosage is 0.5 - 1.5% by weight of cementitious material. Higher dosage
can be used after verification by conducting lab and site trials. Consult CONMIX for
optimum dosage and effect on properties such as strength, setting time, etc.
EFFECT OF OVERDOSING Overdosing may result in higher workability and delay in setting. If intentionally or Manufacturer:
Manufacturer:
LICON MANUFACTURING PLC.
accidentally, dosage used is above the recommended limit, ensure that the stripping time CONMIX LTD.Addis Ababa, Ethiopia
P.O.Box 5452,
P.O.
Tel: Box 5936,
+ 251 11 Sharjah
5544334, 5544557/8
of formwork is extended accordingly. In such cases, provided the concrete is properly United Arab 930109893
Mob: +251 Emirates Sales Office:
Tel: +971 6 5314155
Fax: +251 11 5543610 Tel: +971 6 5682422
cured, the ultimate strength will generally be higher than the regular concrete. The Fax: +971 6 5314332
Email: ethiopia@conmix.com Fax: +971 6 5681442
Email: conmix@conmix.com www.conmix.com
www.conmix.com
effects of overdosing are increased when sulphate resistant cement is used in the
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
concrete mixes because of the chemical nature of the cement as compared to that of product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
OPC. good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
84 CC/MF02/Ver6/07/14
CC/ET/MF02/Ver6/07/14 1/2 Technical Datasheet CC/MF02/Ver6/07/14
CC/ET/MF02/Ver6/07/14 2/2 Technical Datasheet 85
Construction Chemicals Construction Chemicals
MegaAdd SAL
Shotcrete Accelerating Liquid Admixture MegaAdd SAL
DESCRIPTION MegaAdd SAL is a rapid set accelerator in liquid form for cementitious mixes. GENERAL INFORMATION Shelf Life 12 months from date of manufacture when stored under
warehouse conditions in original unopened packing.
STANDARDS ASTM C1141-01, Grade 9, Class A Extreme temperature / humidity may reduce shelf life.
Cleaning Clean all equipments and tools with water immediately after
USES MegaAdd SAL is used as an additive in mixes to enable rapid setting of sprayed use.
concrete and gunite for tunnel lining, water bodies, dams, swimming pools, basement
retaining walls, concrete repairs, etc. HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
Precautions Contact with skin, eyes, etc. must be avoided. If swallowed
seek medical attention immediately.
ADVANTAGES • It is safe to mix with the water line at the spraying nozzle
Hazard Regarded as non-hazardous for transportation.
• Reduces the rebound loss and dust
Disposal Do not reuse containers. To be disposed off as per local
• High early strength, improved water tightness
rules and regulations.
• Fast build-up of multiple layers especially in overhead work Additional Information Refer MSDS. (Available on request.)
• Chloride free
• It also provides waterproofing effect TECHNICAL SERVICE CONMIX Technical Services are available on request for onsite support to assist in the
correct use of its products.
Component - Single
Form - Liquid
Colour - Clear
Specific Gravity ASTM C494 1.32 +/- 0.02
Air Entrainment ASTM C231 Up to 1% over control mix
Chloride Content BSEN 480-10 Nil to BSEN 934-2
pH ASTM C494 9-11
COMPATIBILITY MegaAdd SAL can be used with all types of cements and cementitious materials like
GGBS, fly ash, micro silica, etc.
EFFECT OF OVERDOSING Overdosing may result in very fast setting of cementitious mixes but will not affect other
properties
86 CC/MA07/Ver5/07/12
CC/ET/MA07/Ver5/07/12 1/2 Technical Datasheet CC/MA07/Ver5/07/12
CC/ET/MA07/Ver5/07/12 2/2 Technical Datasheet 87
Construction Chemicals Construction Chemicals
MegaAdd WL1
Waterproofing Admixture for Concrete and Mortar MegaAdd WL1
ADVANTAGES • Reduces permeability HEALTH and SAFETY PPE’s Gloves, goggles and suitable mask must be worn.
• Improves workability Precautions Contact with skin, eyes, etc. must be avoided. If swallowed
seek medical attention immediately.
• Improves durability
Hazard Regarded as non-hazardous for transportation.
• Increases cohesion of mixes
Disposal Do not reuse containers. To be disposed off as per local
• Chloride free
rules and regulations.
• Non-toxic
Additional Information Refer MSDS. (Available on request.)
Component - Single
Form - Liquid
Colour - Dark Brown
Specific Gravity ASTM C494 1.15 +/- 0.02
Air Entrainment ASTM C231 Up to 1% over Control mix
Chloride Content BSEN 480-10 Nil to BSEN 934-2
pH ASTM C494 7-9
Water Absorption BS 1881-122 30% to 40% improvement over control*
* When added at 0.8% dosage in standard mix. Consult Conmix for details.
COMPATIBILITY MegaAdd WL1 can be used with all types of cements and cementitious material like fly
ash, GGBS, micro silica etc. It is compatible with most admixtures.
DOSAGE Recommended dosage is 0.3 - 1.0% by weight of cementitious material. Higher dosage
can be used after verification by conducting lab and site trials. Optimum dosage of
MegaAdd WL1 and effect on concrete properties such as workability, strength, setting
time, etc. are best assessed after preliminary tests on site using the actual materials of
mixes under consideration.
EFFECT OF OVERDOSING Overdosing may result in increased workability and slightly retarding effect. In such
cases, provided concrete is cured properly, ultimate strength will be higher than that of
normal concrete. Manufacturer:
Manufacturer:
LICON MANUFACTURING PLC.
CONMIX LTD.Addis Ababa, Ethiopia
P.O.Box 5452,
P.O.
Tel: Box 5936,
+ 251 11 Sharjah,
5544334, 5544557/8
United Arab 930109893
Mob: +251 Emirates Sales Office :
PACK SIZE 20 ltr, 200 ltr, 1000 ltr and Bulk Tel: +971 6 5314155
Fax: +251 11 5543610
Fax: +971 6 5314332
Tel: +971 6 5682422
Email: ethiopia@conmix.com Fax: +971 6 5681442
Email: conmix@conmix.com www.conmix.com
www.conmix.com
It is the customer’s responsibility to satisfy themselves by checking with the company whether information is still current at the time of use. The customer must be satisfied that the
DISPENSING MegaAdd WL1 should be directly dispensed into the concrete mixer together with the
product is suitable for the use intended. All products comply with the properties shown on current data sheets. However, Conmix does not warrant or guarantee the installation of the
mixing water. products as it does not have any control over installation or end use of the product. All information and particularly the recommendations relating to application and end use are given in
good faith. The products are guaranteed against any manufacturing defects and are sold subject to Conmix standard terms and conditions of sale.
88 CC/MA03/Ver6/07/14
CC/ET/MA03/Ver6/07/14 1/2 Technical Datasheet CC/MA03/Ver6/07/14
CC/ET/MA03/Ver6/07/14 2/2 Technical Datasheet 89
LICON MANUFACTURING PLC.
P.O. Box 5452, Addis Ababa, Ethiopia
Tel: +251 11 5544334
Tel: +251 11 5544557/8
Mob: +251 930109893
Fax: +251 11 5543610
Email: ethiopia@conmix.com
www.conmix.com