Professional Documents
Culture Documents
ZW8100 Es
ZW8100 Es
ZW8100 Es
Higher productivity
Tsudakoma pursues ultra-high speed operation and
designed the“ZW8100”optimally from its frame
structure, beating and shedding, and increased its weft
insertion performance with the pitch-shortened nozzle.
This increases the ZW8100’ s operation speed by 10%
compared with existing models.
Best quality
The robust frame structure, reinforcement of the let-off
motion, and shortening the cloth passage at loom front
allow higher pick density. High speed while keeping the
best fabric quality is attained at high levels. Furthermore,
the PSS-W Programmable Start System is developed to
efficiently reduce stop marks.
Higher operability
The“ZW8100”employs the“Weave Navigation ®
System”for better operability. Almost all electric
adjustments can be done via the Navi-board. Its warp
line height is 40-mm lower than the existing model for
easy access. Furthermore, it automatically conducts pick
finding after recovering from a loom stoppage and re-
starts, demonstrating outstanding operability.
Wider versatility
The“ZW8100”supports a wider range of fabrics: from
extra-fine to thick yarns, from narrow to wide widths,
Tsudakoma’
s water jet loom“ZW series”has a sales and unbalanced construction such as double weave. To
record of more than 140,000 sets and has enjoyed an achieve this versatility, the“ZW8100”uses a combination
of an electronic dobby machine, pitch-shortened nozzle,
excellent reputation as the global standard water jet
a twin pump, and 4-color weft selection.
loom. A short cloth route at loom front allows a higher density
The new model“ZW8100”is developed for the next fabric to be woven steadily.
ZW8100
Balancer
Offset rocking shaft PAT. Offset rocking shaft (Intermediate supporter type) PAT.
Quality Productivity Quality Productivity
For the standard specifications with a reed space of 190 The weight is reduced by separating the main shaft
cm or less, a pipe-type offset rocking shaft is provided. section and the balancing section of the rocking shaft,
Vibration is reduced compared with the existing models achieving high-speed and balanced beating.
for better operation.
4
For some fabrics, the weft tip that protrudes The pitch between the nozzles is With a special feeler and amplifier,
from the nozzle is pulled back to give it a good shortened. This decreases the difference weft detection is enhanced.
posture in order to prevent the weft yarns from between the weft inserting conditions It is possible to detect bright yarn
being entangled. This stabilizes weft insertion. of the two nozzles. The time for weft of 33-dtex or less and mono-
insertion is increased, achieving stable filament which were difficult to
Electric weft pull- weft insertion at high speed operation. detect with the existing feeler.
back device
WBS
ZW8100
Existing model
By inclining the cloth passage from the cloth fell, the stable
operation to produce even unbalanced fabric construction
such as double weave is achieved without causing vertical
movement at the cloth fell.
It is possible to use with the reed protection OP .
Tension compensation
APF-W Automatic Pick Finder
Speed
compensation
ELO
ETU
Speed compensation
ELO speed change
control
Preparation
During loom stoppage After loom re-start
for loom re-start
Quality
In addition to the cloth fell control just before re-start (kickback), the PSS-W
compensates for speeds immediately after re-start to reduce stop marks after
the cloth fell, by the linked operation of the ELO and the ETU. The warp
tension that was changed during loom stoppage is also compensated.
The PSS-W controls speed changes of the ELO immediately after re-start.
It has two setting modes, “Standard” and “Details.” The “Standard” mode is a
simple setting mode for stop mark prevention for general fabrics. The “Details”
mode allows detailed adjustments for stop mark prevention for fabrics which
are difficult to weave.
Rush-start motor
Quality
TLM
Tsudakoma Loom
Monitoring system
Versatility:
Low- and stable tension control in a wide range.
Quality:
Automatic tuning controls the temperature for the hot air
chambers for the best drying.
Productivity:
Network application
Max. yarn speed: 300, 500 m/min
TLM Tsudakoma Loom Monitoring system Size drying according to production amount
Easy operation:
User friendly“Sizing Navigation System.”
Adjustment with the T-MDS.
Energy saving:
Optimized & precise hot air circulation by inverter-controlled
blower system.
10
Liner level
A
W W
Reed space A B
(2C FDP-AⅢW) (1C SDP, RDP)
170cm 1700 2310 3610 3060
180cm 1800 2410 3710 3160
190cm 1900 2510 3810 3260
210cm 2100 2710 4010 3460
230cm 2300 2910 4210 3660
Note: Dimensions may differ depending on the specifications. Please contact Tsudakoma for final confirmation.
11
11
W1 5 ZVG 1 5 H E