Professional Documents
Culture Documents
User's Guide: MPEG-4 AVC Encoder
User's Guide: MPEG-4 AVC Encoder
User's Guide: MPEG-4 AVC Encoder
00
HVE9230
User's Guide
Before using the product, read this User's Guide to make safe, correct use of the product.
Keep the User's Guide in a safe place after reading so you can reread it when you
encounter questions using the product.
Contents
1 Introduction............................................................................................................ 1
2 CONFIG Menu ....................................................................................................... 2
2-1 Menu List................................................................................................................. 2
2-2 CONFIG Menu - Various Parameter Settings - ...................................................... 10
2-2-1 BITRATE Menu - Bitrate Settings/Display - ....................................................................... 10
2-2-2 TS Menu - TS Output Settings -........................................................................................... 14
2-2-3 VIDEO Menu - Video Settings - ........................................................................................... 15
2-2-4 AUDIO Menu - Audio Settings - ........................................................................................... 20
2-2-5 ANCILLARY Menu - ANCILLARY Settings - ..................................................................... 33
2-2-6 TS over IP Menu (Option) - TS over IP Settings - ............................................................... 38
2-2-7 BISS Menu (Option) - BISS Settings - ................................................................................. 39
2-2-8 PSI/SI Menu - PSI/SI Settings - ........................................................................................... 40
2-2-9 ID Menu - ID Settings -......................................................................................................... 41
2-2-10 SNMP Menu - SNMP Settings - ........................................................................................... 44
Appendixes ................................................................................................................. 45
Video and Audio Input/Output Settings ........................................................................... 45
List of Factory Defaults ................................................................................................... 46
CONFIG Menu Defaults ...................................................................................................................... 46
i
HVE9230 User’s Guide
1 Introduction
MPEG-4 AVC Encoder “HVE9230” encodes video signal by MPEG-4 AVC, encodes audio signals by
various kinds of standards, and outputs these encoded signals as MPEG-2 transport stream.
This user’s guide explains the functions specific to HVE9230. As for the functions common to
HVE9210, HVE9230, XVE9310 and HVE9110, please refer to the “HVE9210/HVE9230/XVE9310/
HVE9110 User’s Guide”.
1
HVE9230 User’s Guide
2 CONFIG Menu
2-1 Menu List
CONFIG menu is in the hierarchical structure shown in Table 2-1. The up and down buttons are for
moving within the same level, and the left and right buttons are for moving between upper and lower
levels. These buttons are also for selecting items, setting numerical values and instructing operations
in lower levels.
TS ASI FORMAT
TS CLOCK TS settings
PACKET SIZE
2
HVE9230 User’s Guide
3
HVE9230 User’s Guide
AUDIO3 MODE
BITRATE
AAC TRANSPORT TYPE
SETTING*2
SMC TIME INTERVAL
SBR SIGNAL MODE
DOLBY Sampling Frequency
3
SETTING*
Dialogue Level
Bitstream Mode
Line Mode Profile
RF Mode Profile
DolbySurroundMode
ProductionInfoExists
Mixing Level
Room Type
Copyright
Original Bitstream
De-Emphasis
DC Filter
Lowpass Filter
Left Input Assign
Center Input Assign
Right Input Assign
Metadata Source
DELAY
EXT DELAY
SAMPLE BIT Audio
AUDIO4 MODE settings
BITRATE
AAC TRANSPORT TYPE
SETTING*2
SMC TIME INTERVAL
SBR SIGNAL MODE
DOLBY Sampling Frequency
SETTING*3
Dialogue Level
Bitstream Mode
Line Mode Profile
RF Mode Profile
DolbySurroundMode
ProductionInfoExists
Mixing Level
Room Type
Copyright
Original Bitstream
De-Emphasis
DC Filter
Lowpass Filter
Left Input Assign
Center Input Assign
Right Input Assign
Metadata Source
DELAY
EXT DELAY
SAMPLE BIT
4
HVE9230 User’s Guide
AUDIO5 MODE
BITRATE
AAC TRANSPORT TYPE
SETTING*2
SMC TIME INTERVAL
SBR SIGNAL MODE
DOLBY Sampling Frequency
3
SETTING*
Dialogue Level
Bitstream Mode
Line Mode Profile
RF Mode Profile
DolbySurroundMode
ProductionInfoExists
Mixing Level
Room Type
Copyright
Original Bitstream
De-Emphasis
DC Filter
Lowpass Filter
Left Input Assign
Center Input Assign
Right Input Assign
Metadata Source
DELAY
EXT DELAY
SAMPLE BIT Audio
AUDIO6 MODE settings
BITRATE
AAC TRANSPORT TYPE
SETTING*2
SMC TIME INTERVAL
SBR SIGNAL MODE
DOLBY Sampling Frequency
SETTING*3
Dialogue Level
Bitstream Mode
Line Mode Profile
RF Mode Profile
DolbySurroundMode
ProductionInfoExists
Mixing Level
Room Type
Copyright
Original Bitstream
De-Emphasis
DC Filter
Lowpass Filter
Left Input Assign
Center Input Assign
Right Input Assign
Metadata Source
DELAY
EXT DELAY
SAMPLE BIT
5
HVE9230 User’s Guide
AUDIO7 MODE
BITRATE
AAC TRANSPORT TYPE
SETTING*2
SMC TIME INTERVAL
SBR SIGNAL MODE
DOLBY Sampling Frequency
3
SETTING*
Dialogue Level
Bitstream Mode
Line Mode Profile
RF Mode Profile
DolbySurroundMode
ProductionInfoExists
Mixing Level
Room Type
Copyright
Original Bitstream
De-Emphasis
DC Filter
Lowpass Filter
Left Input Assign
Center Input Assign
Right Input Assign
Metadata Source
DELAY
EXT DELAY
SAMPLE BIT Audio
AUDIO8 MODE settings
BITRATE
AAC TRANSPORT TYPE
SETTING*2
SMC TIME INTERVAL
SBR SIGNAL MODE
DOLBY Sampling Frequency
SETTING*3
Dialogue Level
Bitstream Mode
Line Mode Profile
RF Mode Profile
DolbySurroundMode
ProductionInfoExists
Mixing Level
Room Type
Copyright
Original Bitstream
De-Emphasis
DC Filter
Lowpass Filter
Left Input Assign
Center Input Assign
Right Input Assign
Metadata Source
DELAY
EXT DELAY
SAMPLE BIT
6
HVE9230 User’s Guide
MAPPING MODE
AUDIO1
AUDIO2
AUDIO3
AUDIO4
AUDIO5
AUDIO6
AUDIO7
AUDIO8
GAIN EQUAL to CH1-2
ADJUSTMENT Audio
CH1-2
settings
CH3-4
CH5-6
CH7-8
CH9-10
CH11-12
CH13-14
CH15-16
B39*4 MODE
DELAY
AUDIO2
7
HVE9230 User’s Guide
1
TS over IP* IP OUTPUT
CH1 OUTPUT PORT
PACKET FORMAT
CAST MODE
STREAM IP ADDRESS
STREAM PORT
IPV6 SOURCE ADDR
FEC
TS PACKET TYPE
RTP PT OVERWRITE MODE
OVERWRITE
TS PACKET
FEC PACKET
TSs IN PACKET
CRYPT
CH2 OUTPUT PORT
PACKET FORMAT TS over IP
settings
CAST MODE
STREAM IP ADDRESS
STREAM PORT
IPV6 SOURCE ADDR
FEC
TS PACKET TYPE
RTP PT OVERWRITE MODE
OVERWRITE
TS PACKET
FEC PACKET
TSs IN PACKET
CRYPT
COPY CH1
COMMON IP VERSION
TTL/HOP LIMIT
TOS FIELD
*5
BISS MODE
SW SET
ESW SET
ACTIVE ID SET
AUDIO AUDIO1
ENCRYPTOIN
AUDIO2
BISS
AUDIO3 settings
AUDIO4
AUDIO5
AUDIO6
AUDIO7
AUDIO8
SERVICE NAME
PMT COMPONENT TAG
AC3 DESCRIPTOR
ID TS ID
PROGRAM NO.
PMT PID
NIT PID ID settings
SDT PID
PCR PID
ECM PID*5
8
HVE9230 User’s Guide
9
HVE9230 User’s Guide
Item
Menu Name Explanation Setting Value Setting Details
No.
The meaning of this item depends on the
setting of "2-2-2 TS Menu (2)TS CLOCK."
10
HVE9230 User’s Guide
Item
Menu Name Explanation Setting Value Setting Details
No.
Displays the XXXX kbps Displays the AUDIO5 rate in operation.
(10) AUDIO5 RATE
AUDIO5 rate. NONE AUDIO5 is not encoded.
Displays the XXXX kbps Displays the AUDIO6 rate in operation.
(11) AUDIO6 RATE
AUDIO6 rate. NONE AUDIO6 is not encoded.
Displays the XXXX kbps Displays the AUDIO7 rate in operation.
(12) AUDIO7 RATE
AUDIO7 rate. NONE AUDIO7 is not encoded.
Displays the XXXX kbps Displays the AUDIO8 rate in operation.
(13) AUDIO8 RATE
AUDIO8 rate. NONE AUDIO8 is not encoded.
Displays the XXX kbps Displays the ANCILLARY rate in operation.
(14) ANCILLARY RATE ANCILLARY
rate. NONE ANCILLARY is not encoded.
11
HVE9230 User’s Guide
The available range of the "(4)VIDEO RATE" is calculated from the values of "(1)TS
RATE", the AUDIO1-8 rate and the ancillary rate.
When the value outside the available range is set, the message "VideoRate is too
High" or "VideoRate is too Low" is displayed, and changes are not reflected.
The following table shows the lower limit of the video rate and the recommended video
rate.
The setting of "2-2-3 VIDEO Menu (3)ENTROPY" takes effect only if "(4)VIDEO RATE"
Memo is lower than 20Mbps; otherwise, the setting is overridden to CAVLC.
12
HVE9230 User’s Guide
In case that “2-2-3 VIDEO Menu (4)LATENCY MODE” is set to ULTRA LOW, the video
Memo is encoded under UNSTUFFING CBR at “(5)RATE CTRL MODE”.
13
HVE9230 User’s Guide
Item Setting
Menu Name Explanation Setting Details
No. Range
Sets the format of the TS being The stream is output in 188-byte or
PACKET
(1) ASI FORMAT output from the DVB-ASI output 204-byte units.
connector. BURST The stream is output in 1-byte unit.
INTERNAL The encoder's internal clock is used.
Sets the clock to be used for
(2) TS CLOCK The external clock input from the
controlling the TS bitrate. EXTERNAL
"EXT-CLK" connector is used.
188Byte Outputs 188-byte TS packets.
(3) PACKET SIZE Sets the TS packet size.
204Byte Outputs 204-byte TS packets.
When EXTERNAL is set to "(2)TS CLOCK", enter the external clock from the
Memo "EXT-CLK" connector.
When the video rate falls below the lower limit due to the change made to "(3)PACKET
SIZE", the message "VideoRate is too Low" is displayed, and the change is not
reflected. Set the video rate higher than the lower limit.
14
HVE9230 User’s Guide
Item Setting
Menu Name Explanation Setting Details
No. Range
Enables the input from
SDI1
SDI-IN1.
Enables the input from
SDI2
SDI-IN2.
Selects the SDI input When the SDI is not
① SDI INPUT entered, the encoder will
connector (SDI-IN1/2)
switch to another SDI. If
AUTO the product receives the SDI
from both SDI-IN1 and
SDI-IN2 at the startup,
SDI-IN1 will be selected.
MAIN Encodes by the Main profile.
Selects the encoding
(2) PROFILE HIGH Encodes by the High profile.
profile.
Encodes by the High4:2:2
HIGH4:2:2
profile (8bit).
CABAC Encodes by CABAC.
(3) ENTROPY Selects the entropy.
CAVLC Encodes by CAVLC.
STANDARD Encode in standard latency.
MEDIUM Encode in medium latency.
(4) LATENCY MODE Selects the latency. LOW Encode in low latency.
Encode in super low
SUPER LOW
latency.
ULTRA LOW Encode in ultra low latency.
Number of horizontal pixels:
1920
1920
Sets the number of Number of horizontal pixels:
pixels in the 1440
1440
horizontal direction at
(5) H SIZE@1080
H.264 encoding when Number of horizontal pixels:
1280
SETTING "(11)FORMAT" is 1280
1080.
Number of horizontal pixels:
960
960
Sets the number of Number of horizontal pixels:
pixels in the 720
720
horizontal direction at
(6) H SIZE@SD
encoding when
Number of horizontal pixels:
"(11)FORMAT" is 352
352
either 480I or 576I.
4:3 Aspect ratio is 4:3.
15
HVE9230 User’s Guide
Item Setting
Menu Name Explanation Setting Details
No. Range
“(10)STRENGTH” is
MANUAL
manually selected.
16
HVE9230 User’s Guide
In case that AUTO is set to “(1)SDI INPUT”, set “3-6 MISC Menu (3)OFF SIGNAL” in
Memo “HVE9210/HVE9230/XVE9310/HVE9110 User’s Guide” to LAST FRAME.
“(6)H SIZE@SD” is available only when “(11)FORMAT” is either 480I or 576I. In case
Memo of 352, after having cut for 16 pixels of right side, and then the number of horizontal
pixels are reduced from 704 to 352 for encoding.
Changes to “(4)LATENCY MODE” or “(11)FORMAT" that causes the video rate to fall
below the lower limit (see the table below) have no effect, and the message "Video
Rate is too Low" is displayed. Set the video rate to be over the lower limit before the
changes.
Normally set the recommended video rate or higher. If the video rate is below the
recommended video rate, compressed video may be inferior to the input video.
*For more information about the video rate, see "2-2-1 BITRATE menu".
In case that “(2)PROFILE” is MAIN, the choices of LOW, SUPER LOW and ULTRA
Memo LOW at “(4)LATENCY MODE” are not supported.
In case that “(4)LATENCY MODE” is set to ULTRA LOW, the video is encoded under
Memo UNSTUFFING CBR at “2-2-1 BITRATE Menu (5)RATE CTRL MODE”.
17
HVE9230 User’s Guide
“(4)LATENCY MODE” limits the available audio mode, and the table below shows the
correspondence between the latency mode and the available audio mode. For more
information about the audio mode, see “2-2-4 AUDIO Menu (4)AUDIO1-8 MODE”.
“(7)SD ASPECT RATIO” adds the information of the aspect ratio to the output stream
and does not affect the encoding. It is effective for the decoder that is capable of
squeezing the video using this information. HVD9100 does not refer to the aspect
ratio, and then the video decoded by HVD9100 is not influenced.
Memo VIDEO SD ASPECT RATIO
FORMAT 4:3 16:9
480I29 VUI aspect_ratio_idc = 3 VUI aspect_ratio_idc = 5
576I25 VUI aspect_ratio_idc = 2 VUI aspect_ratio_idc = 4
In case that LOW, SUPER LOW or ULTRA LOW is set to “(4)LATENCY MODE”, the
Memo settings at “(12)M” and “(14)GOP” are invalid.
In case that ENABLE is set to “(8)LOW RATE MODE”, the recommended video bit rate
Memo of “2-2-1 BITRATE Menu (4)VIDEO RATE” is 1 Mbps. The lower bound is 512kbps.
18
HVE9230 User’s Guide
Before ENABLE is set to “(8)LOW RATE MODE”, please set the available choices to
PROFILE, ENTROPY, FORMAT and LATENCY described below. M=3 and GOP=30
are forcely set to the GOP parameters.
In case that more than 20Mbps is set to “2-2-1 BITRATE Menu (4)VIDEO RATE”, the
setting to ENTROPY is overridden to CAVLC. Although STANDARD is set to
LATENCY, the actual latency at the low rate mode is more than the usual
STANDARD*.
(*) The usual STANDARD is the latency at the time when DISABLE is set to “(8)LOW
RATE MODE”.
Memo
Parameter Available choices
PROFILE MAIN, HIGH
ENTROPY CABAC
FORMAT 1080I @29.97 / 30 / 25
720P @59.94 / 60 / 50
480I @29.97
576I @29.97
LATENCY STANDARD
GOP M=3, GOP=30
In case that ENABLE is set to “(8)LOW RATE MODE”, MPEG-4 AAC-LC is not
Memo available for encoding audio.
In case that ENABLE is set to “(8)LOW RATE MODE”, the function of ANCILLARY is
Memo not supported.
In case that ENABLE is set to “(8)LOW RATE MODE”, the video is reduced before
being encoded. Please use HVD9130 to decode the stream, or else other decoders
may not correctly decode it.
Memo
In case that the video bit rate over the usual lower bound is set to “2-2-1 BITRATE
Menu (4)VIDEO RATE”, please set DISABLE to “(8)LOW RATE MODE”, or else the
video is reduced before being encoded.
19
HVE9230 User’s Guide
Item
Menu Name Explanation Setting Range Setting Details
No.
Displays the format of The 1-8ch audio
(1) 1-8ch the 1-8ch audio SDI EMBEDDED embedded in the SDI
inputs. signal is used.
The audio from
"AES/EBU1",
AES/EBU "AES/EBU2",
"AES/EBU3", and
"AES/EBU4" is used.
Selects the format of The 9-16ch audio
MODE
(2) the 9-16ch audio SDI EMBEDDED embedded in the SDI
(9-16ch)
inputs. signal is used.
The combination of
AES/EBU1-4, the 9-16ch
MANUAL audio embedded on the
INPUT SDI and analog audio is
used.
The audio from
"AES/EBU1",
AES "AES/EBU2",
The audio of 9-16ch is "AES/EBU3", and
selected from among "AES/EBU4" is used.
EMB, AES and analog The audio of
SELECT
(3) audio* when MANUAL “Embedded 9-10ch”,
(9-16ch)
is set to “(2)Mode”. “Embedded 11-12ch”,
EMB
The selection is done “Embedded 13-14ch”, and
by every stereo pair. “Embedded 15-16ch”
in the SDI signal is used.
AL1, The audio from the analog
AL2 audio connector is used.
Select the audio
(4) MODE Refer to Table 2-7. --
encoding method.
The setting and display
Sets and displays the depend on "(4)MODE".
(5) BITRATE XXXX kbps
bitrate.
For details, see Table 2-8.
AAC Sets the attributes
(6) Refer to Table 2-9. --
SETTING* about AAC.
Dolby D Sets the attributes
(7) Refer to Table 2-10. --
SETTING about Dolby Digital.
AUDIO1 / Compared to video, the
AUDIO2 / audio in the output stream
AUDIO3 / Sets the delay
(8) DELAY -100 to 50 ms is faster if the value is
AUDIO4 / adjustment.
negative and slower if the
AUDIO5 / value is positive.
AUDIO6 / Encodes without adjusting
AUDIO7 / 0frame
delay.
AUDIO8 The audio in the output
Sets the delay stream is faster than the
1frame
EXT adjustment when time equivalent to one
(9)
DELAY “(4)MODE” is video frame.
SMPTE302M. The audio in the output
stream is faster than the
2frame
time equivalent to two
video frames.
Sets the sample bit 16bit Encodes at 16bit.
SAMPLE
(10) when “(4)MODE” is
BIT 20bit Encodes at 20bit.
SMPTE302M.
20
HVE9230 User’s Guide
Item
Menu Name Explanation Setting Range Setting Details
No.
16ch of audio is
Selects how to assign AUTO automatically mapped into
(11) MODE the audio channels to Audio1-8.
map to AUDIO1 to 8. 16ch of audio is manually
MANUAL
mapped into Audio 1-8.
XXXX : XXXX :
XXXX : XXXX
AUDIO1 / Maps the 16ch of audio into
(1-2 : 3-4 : 5-6 : 7-8ch)
MAPPING AUDIO2 / AUDIO1-8. The formats
AUDIO3 / Selection parameters: of 9-16ch of audio are set
Selects the audio
AUDIO4 / EMB1/EMB2/ at “(3)SELECT(9-16ch).
(12) channel to map to
AUDIO5 / EMB3/EMB4/
AUDIO1-8.
AUDIO6 / (AES1,EMB5,AL1,AL2)/ For details, see Table
AUDIO7 / (AES2,EMB6,AL1,AL2)/
AUDIO8 2-11.
(AES3,EMB7,AL1,AL2)/
(AES4,EMB8,AL1,AL2)
Sets the adjustment of
Selects whether or not DISABLE
each channel individually.
EQUAL TO to apply the audio
(13) Unifies the adjustment of
CH1-2 gain adjustment for
ENABLE each channel to the CH1-2
CH1-2 to all CHs.
setting.
Sets the gain
(14) CH1-2 adjustment of audio -12 to 12 dB --
input CH1-2.
Sets the gain
(15) CH3-4 adjustment of audio -12 to 12 dB --
input CH3-4.
Sets the gain
(16) CH5-6 adjustment of audio -12 to 12 dB --
GAIN input CH5-6.
ADJUSTM Sets the gain
(17) ENT CH7-8 adjustment of audio -12 to 12 dB --
input CH7-8.
Sets the gain
(18) CH9-10 adjustment of audio -12 to 12 dB --
input CH9-10.
Sets the gain
(19) CH11-12 adjustment of audio -12 to 12 dB --
input CH11-12.
Sets the gain
(20) CH13-14 adjustment of audio -12 to 12 dB --
input CH13-14.
Sets the gain
(21) CH15-16 adjustment of audio -12 to 12 dB --
input CH15-16.
Does not switch audio
Selects whether or not DISABLE
mode by ARIB STD B39.
(22) MODE to switch audio mode
Switches audio mode by
by ARIB STD B39. ENABLE
ARIB STD B39.
Sets the delay to
(23) DELAY 0ms to 2000ms --
switch audio mode.
B39
DISABLE Does not encode audio2.
Encodes audio2 according
ENABLE
Selects how to to the ARIB STD B39.
(24) AUDIO2
encode audio2. Encodes audio2 by
MPEG2 AAC-LC 2ch MPEG2 AAC-LC 2/0 or
MPEG2 AAC-LC 1+1.
*HE-AAC / MPEG-4 AAC-LC, DolbyDigital and ARIB STD B39 functions are enabled when options are added on.
21
HVE9230 User’s Guide
22
HVE9230 User’s Guide
23
HVE9230 User’s Guide
Setting
Setting Details
Value
EMB1 Embedded 1-2ch audio input from SDI terminal selected at “2-2-3 VIDEO Menu (1)SDI INPUT”
EMB2 Embedded 3-4ch audio input from SDI terminal selected at “2-2-3 VIDEO Menu (1)SDI INPUT”
EMB3 Embedded 5-6ch audio input from SDI terminal selected at “2-2-3 VIDEO Menu (1)SDI INPUT”
EMB4 Embedded 7-8ch audio input from SDI terminal selected at “2-2-3 VIDEO Menu (1)SDI INPUT”
EMB5 Embedded 9-10ch audio input from SDI terminal selected at “2-2-3 VIDEO Menu (1)SDI INPUT”
EMB6 Embedded 11-12ch audio input from SDI terminal selected at “2-2-3 VIDEO Menu (1)SDI INPUT”
EMB7 Embedded 13-14ch audio input from SDI terminal selected at “2-2-3 VIDEO Menu (1)SDI INPUT”
EMB8 Embedded 15-16ch audio input from SDI terminal selected at “2-2-3 VIDEO Menu (1)SDI INPUT”
AES1 Audio input from "AES/EBU1"
AES2 Audio input from "AES/EBU2"
AES3 Audio input from "AES/EBU3"
AES4 Audio input from "AES/EBU4"
AL1 Audio input from the analog audio connector
AL2 Audio input from the analog audio connector
The same AES input cannot be mapped into both one audio mode that is set MPEG-1
or AAC to in "(4)AUDIO1-8 MODE" settings and another audio mode that is set
Memo SMPTE302M to in "(4)AUDIO1-8 MODE" settings in "(12)MAPPING AUDIO1-8"
settings.
In "(4)AUDIO1-8 MODE",
・in case that MPEG-1 LayerII or MPEG-2 BC is selected, the maximum number of
PES is 8.
Memo ・in case that MPEG-2 AAC-LC, MPEG-4 AAC-LC, MPEG-4 HE-AAC, MPEG-4
AAC-LD or MPEG-4 AAC-ELD is selected, the maximum number of PES is 4.
・in case that SMPTE302M is selected, the maximum number of PES is 8.
・in case that Dolby Digital Pass-Thru is selected, the maximum number of PES is 4.
In case that the option of “Dolby Digital” is added, dolby digital can be assigned to
Memo “(4)Audio1-8 Mode” up to 2PESs. Furthermore, the option of “Dolby Digital 4PES” is
added, dolby digital can be assigned up to 4PESs.
24
HVE9230 User’s Guide
Setting “(5)AUDIO1-8 BITRATE” that causes VIDEO RATE to fall below the lower
limit (see the table below) have no effect and the message "Video Rate is too Low" is
displayed. Set the video rate to be over the lower limit before the changes.
Normally set the recommended video rate or higher. If the video rate is below the
recommended video rate, compressed video may be inferior to the input video.
*For more information about the video rate, see "2-2-1 BITRATE menu".
Use "(9)EXT DELAY" to adjust lip-synching if necessary, in case that the audio stream,
Memo which is encoded by the external audio encoder, is encapsulated in SMPTE302M
stream and is transmitted.
Set “(14)-(21) GAIN ADJUSTMENT” to 0dB, in case that the audio stream such as
Memo Dolby E is encapsulated in SMPTE302M stream and is transmitted.
"(10)SAMPLE BIT” is available at SMPTE302M. The sample bit is 16bit for other
Memo audio mode.
25
HVE9230 User’s Guide
When ULTRA LOW is set to “2-2-3 VIDEO Menu (4)Latency Mode”, a negative value is
Memo not effective in "(8)DELAY".
“2-2-3 VIDEO Menu (4)LATENCY MODE” limits the available audio mode, and the
table below shows the correspondence between the latency mode and the available
audio mode.
When ULTRA LOW is set to “2-2-3 VIDEO Menu (4)LATECY MODE”, "(9)EXT DELAY”
Memo can be set to only 0 frame.
When "MPEG4 HE-AAC" is set at the "(4)AUDIO1-8 Mode", the latency of encoding
audio increases when conditions fall under the following category:
Memo ・720P50, 720P59.94, 720P60, 1080P50, 1080P59.94 or 1080P60 is set to "2-2-3
VIDEO Menu (11)FORMAT".
・MEDIUM is set to "2-2-3 VIDEO Menu (4)LATENCY MODE".
In case that dolby digital pass through is set to "(4)Audio1-8 MODE'', use the dolby
Memo digital encoder whose delay is 187ms.
In case that dolby digital pass through is set to "(4)Audio1-8 MODE'', use the dolby
Memo digital encoder whose bit rate is over 128kbps.
The delay of this encoder increases by 168ms, when dolby digital pass through is set
to "(4)Audio1-8 Mode'' and either of following conditions is met:
Memo ・"2-2-3 VIDEO Menu (4)LATENCY MODE'' is LOW.
・"2-2-3 VIDEO Menu (12)M'' is either 1 or 2.
In case that dolby digital pass through is set to "(4)Audio1-8 Mode'', the settings of
Memo "(14)-(21) GAIN ADJUSTMENT'' do not take effect.
26
HVE9230 User’s Guide
In case that ENABLE is set to "(22)B39 MODE'', the available audio mode is only
Memo MPEG2 AAC-LC.
In case that "(22)-(24) B39'' is used, the following setting values are used as the bit
rates of audio1 and audio2.
・a group of MPEG2 AAC-LC 1ch (1/0)
・a group of MPEG2 AAC-LC 2ch (1+1, 2/0)
Memo ・a group of MPEG2 AAC-LC 5.1ch (4/0, 3/2/1, 6/0)
In case that the group of MPEG2 AAC-LC 5.1ch is not used, set its bit rate to 320kbps.
When MPEG2 AAC-LC 2ch is set to "(24) AUDIO2'', the bit rate of the audio2 is always
equal to that of MPEG2 AAC-LC 2ch.
In case that "(22)-(24) B39'' is used, the video rate is calculated, considering the bit
rates of audio1 and audio2 according to the following audio modes.
・a group of MPEG2 AAC-LC 1ch (1/0)
・a group of MPEG2 AAC-LC 2ch (1+1, 2/0)
Memo ・a group of MPEG2 AAC-LC 5.1ch (4/0, 3/2/1, 6/0)
In case that the audio2 is not used, the video rate is higher by setting DISABLE to "(24)
AUDIO2''.
In case that MPEG2 AAC-LC 2/0 is set to "(24)AUDIO2'', the bit rate of audio2 is that of
MPEG2 AAC-LC 2ch (1+1, 2/0).
In case that MPEG2 AAC-LC 2ch is set to "(24) AUDIO2'', the audio2 always encoded.
Memo If the audio modes required by B39 are 2S, 5.1 or 5.1+S, the audio mapping for audio2
obeys that for audio2, or else the audio mapping for audio2 obeys that for audio1.
In case that the audio is switched by "(22)-(24)B39'', the TSs without multiplexing
Memo audio PES are transmitted for about 1 second (maximum). Therefore, decoding
these TSs by an STB may make noises.
Memo "(22)-(24) B39'' does not support the audio down-mix specification.
Before changing the setting values in 2-2 CONFIG Menu, either set DISABLE to "(22)
Memo MODE'' or stop inputting SDI signal.
Memo In case that there is no group1 data in embedded audio, group2 data is not used.
27
HVE9230 User’s Guide
To pass streams of the external Dolby E Encoder through by using SMPTE302M, the
system should be typically set as follows.
CAMERA SDI
Memo
HVE9230
Dolby E Encoder
AES/EBU
(DP571)
Dolby E Bitstream
DVB-ASI
MONITOR SDI
HVD9100
Dolby E Decoder AES/EBU
(DP572)
Dolby E Bitstream
28
HVE9230 User’s Guide
HVE9230 has 4 processes of audio-encoding. The maximum number of the PES that one process
can encode is shown in Table 2-12.
Table 2-12 Maximum number of PES that one process can encode
Therefore, HVE9230 can encode the maximum 8 PES when AUDIO1 to AUDIO8 are encoded by
MPEG1 or SMPTE302M. HVE9230 can encode the maximum 4 PES when they are encoded by
MPEG-2 AAC-LC, MPEG-4 AAC-LC, MPEG-4 HE-AAC, MPEG-4 AAC-LD, MPEG-4 AAC-ELD or
Dolby Digital Pass-Thru. In case of DolbyDigital1, the maximum 4 PES are available, when Dolby
Digital option is added on. The maximum numbers of the audio channels are 16ch.
In case that more than two kinds of audio modes are used, any audio mode can be assigned to one
process. There are some limitations when MPEG1, SMPTE302M or DolbyDigital is selected as the
audio mode.
>One process encodes two lines of audio by MPEG1 and SMPTE302M at the same time, but the
maximum number of audio channel are 8ch.
(Exp.) One process can encode MPEG1 + SMPTE302M 6ch. (total 8ch)
One process cannot encode MPEG1 + SMPTE302M 8ch. (total 10ch)
> One process cannot encode two lines of audio by MPEG1 and DolbyDigital at the same time.
> One process cannot encode two lines of audio by SMPTE302M and Dolby Digital at the same time.
Table 2-13 shows some of the combination of audio modes. If the combination of audio modes is
available, these audio modes can be arbitrarily mapped into from AUDIO1 to AUDIO8.
AUDIO
AUDIO1 AUDIO2 AUDIO3 AUDIO4 AUDIO5 AUDIO6 AUDIO7 AUDIO8
MODES
MPEG1 MPEG1 MPEG1 MPEG1 MPEG1 MPEG1 S302M2ch S302M2ch
MPEG1
MPEG1 MPEG1 MPEG1 MPEG1 S302M8ch - - -
+
MPEG1 MPEG1 MPEG1 MPEG1 MPEG1 S302M6ch - -
S302M
MPEG1 MPEG1 S302M6ch S302M6ch - - - -
MPEG1 MPEG1 MPEG1 MPEG1 MPEG1 AAC 2/0 AAC 3/2/1 - -
+ MPEG1 MPEG1 AAC 3/2/1 AAC 6/0 - - - -
AAC MPEG1 AAC 4/0 AAC 4/0 AAC 6/0 - - - -
MPEG1 MPEG1 MPEG1 MPEG1 MPEG1 MPEG1 MPEG1 DolbyDPass -
+ MPEG1 MPEG1 MPEG1 MPEG1 DolbyDPass DolbyDPass - -
DolbyDPass MPEG1 MPEG1 DolbyDPass DolbyDPass DolbyDPass - - -
MPEG1 MPEG1 MPEG1 MPEG1 MPEG1 MPEG1 MPEG1 DolbyD 2/0 -
+ MPEG1 MPEG1 MPEG1 DolbyD 2/0 DolbyD 2/0 DolbyD 2/0 DolbyD 2/0 -
DolbyD MPEG1 MPEG1 DolbyD 2/0 DolbyD 2/0 DolbyD 2/0 DolbyD 2/0 - -
AAC AAC 2/0 AAC4/0 AAC 3/2/1 DolbyDPass - - - -
+ AAC 3/2/1 AAC 3/2/1 DolbyDPass DolbyDPass - - - -
DolbyDPass AAC 3/2/1 DolbyDPass DolbyDPass DolbyDPass - - - -
1
The option for DolbyDigital 4 PES (maximal) is available.
29
HVE9230 User’s Guide
30
HVE9230 User’s Guide
When AUTO is set to "(11)MODE", audio input is automatically assigned to INPUT 1-16ch in valid 2ch
units in order AUDIO1, ADIO2, AUDIO3, AUDIO4, AUDIO5, AUDIO6, AUDIO7 and AUDIO8.
Table 2-14 and Table 2-15 show an example of how audio is assigned when AUTO is set to
"(11)MODE".
AUDIO CHANNEL
AUDIO MODE
1 2 3 4 5 6 7 8
MPEG1 Mono C - - - - - - -
MPEG1 Dual Mono Mono Mono - - - - - -
MPEG1 Stereo L R - - - - - -
MPEG2 AAC-LC 1/0 C - - - - - - -
MPEG2 AAC-LC 1+1 Mono Mono - - - - - -
MPEG2 AAC-LC 2/0 L R - - - - - -
MPEG2 AAC-LC 4/0 L R L R - - - -
MPEG2 AAC-LC 3/2/1 L R C LFE LS RS - -
MPEG2 AAC-LC 6/0 L R L R L R - -
MPEG4 AAC-LC 2/0 L R - - - - - -
MPEG4 AAC-LC 3/2/1 L R C LFE LS RS - -
MPEG4 HE-AAC 2/0 L R - - - - - -
MPEG4 HE-AAC 3/2/1 L R C LFE LS RS - -
MPEG4 AAC-LD 2/0 L R - - - - - -
MPEG4 AAC-LD 3/1 L R C B - - - -
MPEG4 AAC-LD 3/2/1 L R C LFE LS RS - -
MPEG4 AAC-ELD 2/0 L R - - - - - -
MPEG4 AAC-ELD 3/1 L R C B - - - -
MPEG4 AAC-ELD 3/2/1 L R C LFE LS RS - -
SMPTE302M 2ch ch1 ch2 - - - - - -
SMPTE302M 4ch ch1 ch2 ch3 ch4 - - - -
SMPTE302M 6ch ch1 ch2 ch3 ch4 ch5 ch6 - -
SMPTE302M 8ch ch1 ch2 ch3 ch4 ch5 ch6 ch7 ch8
Dolby D Pass-Thru ch1 + ch2
Dolby Digital 1/0 C
Dolby Digital 2/0 L R
M: Monoural
L: Left channel
R: Right channel
C: Center channel
B: Back
LFE: Low-Frequency Effects channel
LS: Left Surround channel
RS: Right Surround channel
ch1-ch8: Monaural channel number
31
HVE9230 User’s Guide
AUDIO MODE Audio embedded in SDI/ AES input connector / Analog audio
A1 MODE / A2 MODE INPUT 1-8ch INPUT 9-16ch
/ A3 MODE / A4 MODE
/ A5 MODE / A6 MODE 1 2 3 4 5 6 7 8 9 10 11 12 12 14 15 16
/ A7 MODE / A8 MODE
MPEG1 Mono / MPEG1 Mono C C C C C C C C - - - - - - - -
/ MPEG1 Mono / MPEG1 Mono
/ MPEG1 Mono / MPEG1 Mono A1 A2 A3 A4 A5 A6 A7 A8
/ MPEG1 Mono / MPEG1 Mono
AAC 5.1ch / AAC 2ch L R C LFE LS RS L R L R C LFE LS RS L- R
/ AAC 5.1ch / AAC 2ch
/ NONE / NONE A1 A2 A3 A4
/ NONE / NONE
AAC 3/2/1 / MPEG1 2ch L R C LFE LS RS L R - - - - - - - -
/ NONE / NONE
/ NONE / NONE A1 A2
/ NONE / NONE
AAC 5.1ch / AAC 5.1ch L R C LFE LS RS L R C LFE LS RS - - - -
/ NONE / NONE
/ NONE / NONE A1 A2
/ NONE / NONE
SMPTE302M 8ch / SMPTE302M 8ch ch1 ch2 ch3 ch4 ch5 ch6 ch7 ch8 ch1 ch2 ch3 ch4 ch5 ch6 ch7 ch8
/ NONE / NONE
/ NONE / NONE A1 A2
/ NONE / NONE
MPEG1 2ch / MPEG1 2ch L R L R L R L R L R L R L R L R
/ MPEG1 2ch / MPEG1 2ch
/ MPEG1 2ch / MPEG1 2ch A1 A2 A3 A4 A5 A6 A7 A8
/ MPEG1 2ch / MPEG1 2ch
Dolby Digital / DolbyDPass L R ch1 ch2 L R L R - - - - - - - -
/ DolbyD 2ch / DolbyD 2ch
/ NONE / NONE A1 A2 A3 A4
/ NONE / NONE
MPEG1 2ch / SMPTE302M 6ch L R ch1 ch2 ch3 ch4 ch5 ch6 ch1 ch2 L R L R - -
/ DolbyDPass / AAC 2ch
/ DolbyD 2ch / NONE A1 A2 A3 A4 A5
/ NONE / NONE
*A1, A2, A3, A4, A5, A6, A7 and A8 mean AUDIO1, AUDIO2, AUDIO3, AUDIO4, AUDIO5, AUDIO6, AUDIO7 and AUDIO8, respectively.
L: Left channel
R: Right channel
C: Center channel
LFE: Low-Frequency Effects channel
LS: Left Surround channel
RS: Right Surround channel
ch1-ch8: Monoural channel number
32
HVE9230 User’s Guide
Item Setting
Menu Name Explanation Setting Details
No. Range
ENABLE Transmits the TimeCode in J187
(J.187) format.
Selects whether ENABLE
Transmits the TimeCode in
(1) SELECT or not to transmit (SMPTE203
SMPTE2038 format.
the TimeCode. 8)
DISABLE Does not transmit the TimeCode.
TIME
CODE
Sets the line
LINE
(2) VITC where a VITC is 8 – 22 --
(SD)
embedded.
Selects whether
ENABLE Transmits the LTC.
(3) LTC SELECT or not to transmit
the LTC. DISABLE Does not transmit the LTC.
Selects whether
ENABLE Transmits the B22(ID).
ARIB or not to transmit
(4) SELECT
B22(ID) the ARIB
B22(ID). DISABLE Does not transmit the B22(ID).
Selects whether
ARIB B22 or not to transmit ENABLE Transmits the B22(DATA).
(5) SELECT
(DATA) the ARIB
B22(DATA). DISABLE Does not transmit the B22(DATA).
33
HVE9230 User’s Guide
Item Setting
Menu Name Explanation Setting Details
No. Range
Selects whether Transmits the closed caption by
ENABLE
or not to transmit inserting it to the video user data.
SELECT
the closed Does not transmit the closed
DISABLE
caption. caption.
Sets the line
where a closed
LINE 0 to 25 --
caption is
embedded.
Selects whether A closed caption is embedded in
ENABLE
CLOSED BOTTOM a closed caption the bottom field.
(10)
CAPTION FIELD is embedded in A closed caption is not embedded
the bottom field. DISABLE
in the bottom field.
STANDA Selects the ATSC Obeys ATSC A-72.
RD standard. SCTE Obeys SCTE128.
Transmits the closed caption
NORTH
according to ATSC standard in
AMERICA
ATSC Selects the north America.
AREA standard. Transmits the closed caption
KOREA according to the standard in
Korea.
Transmits the AFD & BAR DATA
Selects whether
ENABLE by inserting it to the video user
or not to transmit
SELECT data.
the AFD & BAR
Does not transmit the AFD & BAR
AFD & DATA. DISABLE
(11) DATA.
BAR DATA
Sets the line
where the AFD &
LINE 8 to 25 --
BAR DATA is
embedded.
Selects whether
ENABLE Transmits the OP-47 packets.
or not to transmit
SELECT
the OP-47 Does not transmit the OP-47
packets. DISABLE
(12) OP-47 packets.
Sets the line
where an OP-47
LINE 8 to 25 --
packet is
embedded.
Selects whether ENABLE Transmits the user data1 packets.
SELECT or not to transmit Does not transmit the user data1
the packets. DISABLE
packets.
Sets the line
LINE where a packet 8 to 1125 --
USER
is embedded.
(13) SELECTIO
SMPTE Transmits the packets in SMPTE
N1
RDD11 RDD11 format.
Selects the PES Transmits the packets in ARIB B40
PES ARIB B40
format. format.
Transmits the packets in
USER SMPTE2038
SMPTE2038 format.
SELEC
TION Selects whether ENABLE Transmits the user data2 packets.
SELECT or not to transmit Does not transmit the user data2
DISABLE
the packets. packets.
Sets the line
LINE where a packet 8 to 1125 --
USER
is embedded.
(14) SELECTIO
SMPTE Transmits the packets in SMPTE
N2
RDD11 RDD11 format.
Selects the PES Transmits the packets in ARIB B40
PES ARIB B40
format. format.
Transmits the packets in
SMPTE2038
SMPTE2038 format.
*ARIB B37 function is enabled when option is added on.
34
HVE9230 User’s Guide
When ENABPE is set to "2-2-3 VIDEO Menu (8)LOW RATE MODE", the function of
Memo ANCILLARY is not supported.
When SUPER LOW or ULTRA LOW is set to "2-2-3 VIDEO Menu (4)LATENCY
Memo MODE", the function of ANCILLARY is not supported.
Memo Setting the same line is impossible except for "TIMECODE" setting.
For LINE of "(2)VITC", selects the top field line, as shown in the table below, which is
effective for each SD video format.
Memo FORMAT LINE (TOP FIELD / BOTTOM FIELD)
480I29.97 9 to 19 / 264 to 282
576I25 9 to 22 / 311 to 335
Memo In case that the PES format is SMPTE2038, "(3)LTC" can be transmitted.
Please set DID and SDID of the packet specified by "(4) to (8)ARIB", "(9) to (11)ATSC",
Memo "(13) to (14)USER SELECTION" through the web-based GUI.
35
HVE9230 User’s Guide
Memo "(4) to (8)ARIB", "(9) to (11)ATSC" and “(12)OP-47” can not be used simultaneously.
"(4)ARIB B22(ID)" and "(5)ARIB B22(DATA)" are available only when 1080i is selected
Memo in "2-2-3 VIDEO Menu (11)FORMAT".
Neither "(6)ARIB B23(CONTROL) " nor "(7)ARIB B23(CAPTION)" are available when
Memo 576i or 1080P is selected in "2-2-3 VIDEO Menu (11)FORMAT".
In case that DISABLEs are set to all the packets in "(6)ARIB B23(CONTROL)" through
Memo the web-based GUI, "(6)ARIB B23(CONTROL)" is not transmitted even though
ENABLE is set to "(6)ARIB B23(CONTROL)".
In case that DISABLEs are set to all the packets in "(7)ARIB B23(CAPTION)" through
Memo the web-based GUI, "(7)ARIB B23(CAPTION)" is not transmitted even though
ENABLE is set to "(7)ARIB B23(CAPTION)".
In case that ENABLE is set to ARIB B37, other ancillary ((1) to (3)TIMECODE, (4) to
Memo (5)ARIB B22, (6) to (7)ARIB B23, (9) to (11)ATSC, (12)OP-47 and (13) to (14)USER
SELECTION) are not available, but ARIB B39 is available.
The packets in "(9)SMPTE334M" that are set ENABLEs to through the web-based GUI
Memo must be on the same line.
In case that DISABLEs are set to all the packets in "(9)SMPTE334M" through the
Memo web-based GUI, "(9)SMPTE334M" is not transmitted even though ENABLE is set to
"(9)SMPTE334M".
"(10)Closed Caption" and "(11)AFD & BAR Data" can be simultaneously transmitted,
Memo but it is not allowed to set the same line.
In case that 0 is set to the line in "(10)Closed Caption", the line where a closed caption
Memo is embedded is automatically searched. Any other ancillary data cannot be
transmitted when this function is used.
36
HVE9230 User’s Guide
It is not allowed to set the same line to "(10)Closed Caption" and other ancillary.
Memo "(11)AFD & BAR Data" are also the same.
In case that DISABLEs are set to all the packets in "(12)OP-47" through the
Memo web-based GUI, "(12)OP-47" is not transmitted even though ENABLE is set to
"(12)OP-47".
The packets in "(13) to (14)USER SELECTION" that are set ENABLEs to through the
Memo web-based GUI must be on the same line.
Please set the effective line to the video format in "(13) to (14)USER SELECTION"
(refer to the table below), or else the video from a decoder may be damaged.
In case that DISABLEs are set to all the packets in "(13) to (14)USER SELECTION"
Memo through the web-based GUI, "(13) to (14)USER SELECTION" are not transmitted even
though ENABLEs are set to "(13) to (14)USER SELECTION".
37
HVE9230 User’s Guide
“Appendixes Video and Audio Input/Output Settings” explains the relationship between
Memo CH1 (CH2) and TS1 (Resp. TS2).
38
HVE9230 User’s Guide
39
HVE9230 User’s Guide
Item
Menu Name Explanation Setting Range Setting Details
No
OUTPUT Selects whether or not DISABLE Does not transmit NIT.
(1) to transmit NIT. ENABLE Transmits NIT.
NETWOKR ID Sets the Network ID of 0x0000 to --
(2)
NIT. 0xFFFF
NIT NETWORK NAME Sets the network name up to 16 Setting value
(3) of NIT. characters 0 to 9, a to z, A to Z, ., -, _
CARRIER Sets the carrier of NIT. up to 5 Setting value
(4) characters 0 to 9, a to z, A to Z, ., -, _
OUTPUT Selects whether or not DISABLE Does not transmit SDT.
(5) to transmit SDT. ENABLE Transmits SDT.
PROVIDER NAME Sets the provider name up to 16 Setting value
(6) SDT of SDT. characters 0 to 9, a to z, A to Z, ., -, _
SERVICE NAME Sets the service name up to 16 Setting value
(7) of SDT. characters 0 to 9, a to z, A to Z, ., -, _
COMPONENT TAG Selects whether or not DISABLE Does not insert the component
(8) to insert the component tag.
PMT tag in PMT. ENABLE Inserts the component tag.
AC-3 DESCRIPTOR Sets the manner of the ATSC Descriptor for ATSC is inserted.
(9)
descriptor. DVB Descriptor for DVB is inserted.
Please set the detail settings of "(1) to (4)NIT" and "(5) to (7)SDT" through the
Memo web-based GUI.
In "(8)Component Tag", the video, the audio1 and the audio2 are set to 0x00, 0x01 and
Memo 0x11 respectively.
Memo Inserting the component tags for the 8 PESes of SMPTE302M is not supported.
40
HVE9230 User’s Guide
Item
Menu Name Explanation Setting Range Setting Details
No.
Sets the transport 0x0000 to 0xFFFF
(1) TS ID --
stream ID. (0 to 65535)
0x0001 to 0xFFFF
(2) PROGRAM NO. Sets the program No. --
(1 to 65535)
0x0010 to 0x1FFE
(3) PMT PID Sets the PMT packet ID. --
(16 to 8190)
0x0010 to 0x1FFE
(4) NIT PID Sets the NIT packet ID. --
(16 to 8190)
0x0010 to 0x1FFE
(5) SDT PIF Sets the SDT packet ID. --
(16 to 8190)
0x0010 to 0x1FFE
(6) PCR PID Sets the PCR packet ID. --
(16 to 8190)
Sets the ECM packet ID This is fixed at 0x1FFF
when MODE-E is set to 0x0010 to 0x1FFE when MODE-1 is set to
(7) ECM PID*
"2-2-7 BISS Menu (16 to 8190) "2-2-7 BISS Menu
(1)MODE". (1)MODE".
0x0010 to 0x1FFE
(8) VIDEO PID Sets the video packet ID. --
(16 to 8190)
VIDEO
Sets the video stream 0xE0 to 0xEF
(9) V STREAM ID --
ID. (224 to 239)
Sets the AUDIO1 packet 0x0010 to 0x1FFE
(10) AUDIO1 PID (16 to 8190)
--
ID.
Sets the AUDIO2 packet 0x0010 to 0x1FFE
(11) AUDIO2 PID (16 to 8190)
--
ID.
Sets the AUDIO3 packet 0x0010 to 0x1FFE
(12) AUDIO3 PID (16 to 8190)
--
ID.
Sets the AUDIO4 packet 0x0010 to 0x1FFE
(13) AUDIO4 PID (16 to 8190)
--
ID.
Sets the AUDIO5 packet 0x0010 to 0x1FFE
(14) AUDIO5 PID --
ID. (16 to 8190)
Sets the AUDIO6 packet 0x0010 to 0x1FFE
(15) AUDIO6 PID --
ID. (16 to 8190)
Sets the AUDIO7 packet 0x0010 to 0x1FFE
(16) AUDIO7 PID --
ID. (16 to 8190)
Sets the AUDIO8 packet 0x0010 to 0x1FFE
(17) AUDIO8 PID --
ID. (16 to 8190)
0xBD, 0xC0 to This is fixed at 0xBD
AUDIO Sets the AUDIO1 stream 0xDF when SMPTE302M is set
(18) A1 STREAM ID
ID. (189, 192 to 223) to "2-2-4 AUDIO Menu
(3)AUDIO1 MODE".
0xBD, 0xC0 to This is fixed at 0xBD
Sets the AUDIO2 stream 0xDF when SMPTE302M is set
(19) A2 STREAM ID
ID. (189, 192 to 223) to "2-2-4 AUDIO Menu
(3)AUDIO2 MODE".
0xBD, 0xC0 to This is fixed at 0xBD
Sets the AUDIO3 stream 0xDF when SMPTE302M is set
(20) A3 STREAM ID
ID. (189, 192 to 223) to "2-2-4 AUDIO Menu
(3)AUDIO3 MODE".
0xBD, 0xC0 to This is fixed at 0xBD
Sets the AUDIO4 stream 0xDF when SMPTE302M is set
(21) A4 STREAM ID
ID. (189, 192 to 223) to "2-2-4 AUDIO Menu
(3)AUDIO4 MODE".
0xBD, 0xC0 to This is fixed at 0xBD
Sets the AUDIO5 stream 0xDF when SMPTE302M is set
(22) A5 STREAM ID
ID. (189, 192 to 223) to "2-2-4 AUDIO Menu
(3)AUDIO5 MODE".
41
HVE9230 User’s Guide
Item
Menu Name Explanation Setting Range Setting Details
No.
0xBD, 0xC0 to This is fixed at 0xBD
Sets the AUDIO6 stream 0xDF when SMPTE302M is set
(23) A6 STREAM ID
ID. (189, 192 to 223) to "2-2-4 AUDIO Menu
(3)AUDIO6 MODE".
0xBD, 0xC0 to This is fixed at 0xBD
Sets the AUDIO7 stream 0xDF when SMPTE302M is set
(24) A7 STREAM ID
ID. (189, 192 to 223) to "2-2-4 AUDIO Menu
(3)AUDIO7 MODE".
0xBD, 0xC0 to This is fixed at 0xBD
Sets the AUDIO8 stream 0xDF when SMPTE302M is set
(25) A8 STREAM ID
ID. (189, 192 to 223) to "2-2-4 AUDIO Menu
(3)AUDIO8 MODE".
Sets the stream type Sets the "MPEG-1 Audio
0x03(MPEG-1)
MPEG1 when MPEG-1 is Layer2" stream type.
(26)
STREAM TYPE selected as the audio Sets the "MPEG-2 BC"
0x04(MPEG-2 BC)
format. stream type.
Sets the TIMECODE 0x0010 to 0x1FFE
(27) TIMECODE PID --
packet ID. (16 to 8190)
Sets the ARIB B22 0x0010 to 0x1FFE
(28) ARIB B22 PID --
packet ID. (16 to 8190)
ARIB B23(CTL) Sets the ARIB B23 0x0010 to 0x1FFE
(29) --
PID (CONTROL) packet ID. (16 to 8190)
ARIB B23(CAP) Sets the ARIB B23 0x0010 to 0x1FFE
(30) --
PID (CAPTION) packet ID. (16 to 8190)
* Sets the ARIB B37 0x0010 to 0x1FFE
(31) ANCILLARY ARIB B37 PID --
packet ID. (16 to 8190)
SMPTE334M Sets the SMPTE334M 0x0010 to 0x1FFE
(32) --
PID packet ID. (16 to 8190)
Sets the OP-47 packet 0x0010 to 0x1FFE
(33) OP-47 PID --
ID. (16 to 8190)
Sets the user data1 0x0010 to 0x1FFE
(34) USER1 PID --
packet ID. (16 to 8190)
Sets the user data2 0x0010 to 0x1FFE
(35) USER2 PID --
packet ID. (16 to 8190)
* The BISS and ARIB B37 functions are enabled when the options are added on.
PIDs must be unique, but it is allowed that "(6)PCR PID" is the same as "(8)VIDEO
Memo PID" and that "(27)TIMECODE PID" is the same as "(28)ARIB B22 PID". If the same
number is set to the PIDs, pressing ENT button is of no effect.
Setting "(7)ECM PID" is available only when "2-2-7 BISS Menu (1)MODE" is MODE-E.
Memo The PID in MODE-1 is fixed at 0x1FFF.
Setting "(18)A1 STREAM ID'', "(19)A2 STREAM ID'', "(20)A3 STREAM ID'', "(21)A4
STREAM ID'', "(22)A5 STREAM ID'', "(23)A6 STREAM ID'', "(24)A7 STREAM ID'' and
Memo "(25)A8 STREAM ID'' is available when MPEG-1 or AAC is set to the audio modes from
A1 to A8. The stream IDs are fixed at 0xBD when SMPTE302M or Dolby Digita is set
to the audio modesl.
42
HVE9230 User’s Guide
The correspondence between setting value to ''(26)MPEG1 STREAM TYPE'' and the
standard is as follows.
Memo 0x03: ISO/IEC 11172-3 (MPEG-1)
0x04: ISO/IEC 13818-3 (MPEG-2 BC)
43
HVE9230 User’s Guide
44
HVE9230 User’s Guide
Appendixes
Video and Audio Input/Output Settings
The video from SDI1 or SDI2 is encoded according to the settings of “2-2-3 VIDEO Menu”, while the
audio from SDI1, SDI2, AES/EBU1 to 4 or analog audio is encoded according to the settings of “2-2-4
AUDIO Menu”, and the stream is output through ASI-OUT1, ASI-OUT2, IP CH1 and IP CH2.
Fig-Appendix 1 shows the outline of the input and the output of video and audio, and Fig-Appendix 2
shows the outline of encoding audio.
ENCODE ASI-OUT1
SDI-IN1 TS1 / IP(CH1)*
VIDEO
VIDEO
SDI Embedded
Audio 1-8ch AUDIO1 AUDIO5
1-8ch
ENCODE
AUDIO2 AUDIO6
SDI Embedded AUDIO
Audio 9-16ch AUDIO3 AUDIO7
9-16ch
AUDIO4 AUDIO8
AES/EBU 1~4
45
HVE9230 User’s Guide
46
HVE9230 User’s Guide
47
HVE9230 User’s Guide
48
HVE9230 User’s Guide
CRYPT DISABLE
49
HVE9230 User’s Guide
50
HVE9230 User’s Guide
51
HVE9230 User’s Guide
Contact Information
52