Professional Documents
Culture Documents
Instruction Manual (Input Conversion)
Instruction Manual (Input Conversion)
(Input Conversion)
DC1010/1020
1030/1040
Rev 4
Contents
1) DC1010
TC
RTD
2) DC1020/DC1030/1040
TC
RTD
Linear TC
7 7 Set Input Code in Level 3
for TC or Linear Input after Profer Wiring
8 8
9 9
10 10
2) DC1030
Input Wiring
Linear TC
11 11
Set Input Code in Level 3
for TC or Linear Input after Profer Wiring
12 12
13 13
14 14
3) DC1020/1040
Input Wiring
Linear TC
17 17
Set Input Code in Level 3
for TC or Linear Input after Profer Wiring
18 18
19 19
20 20
3. Linear Input H/W Setting
For jumper, please see ‘1. Input Changes’ section.
1) DC1010
R1
R4 R2
S1 S4 R5 R3
S2
S3
S5
7 8 9 10
Input Code S1 to S5
Input Type R1 to R5
AN 4 AN 5 Jumper Status
0~20 mA
mA R3 = 100 R5 = 2.4 S3 & S5 Short
4~20 mA
0~1 V R1 = 2 K S1 & S4 Short
V 0~5 V 1~5 V R2 = 10 K R4 = 100 S2 & S4 Short
0~10 V 2~10 V R3 = 22 K S3 & S4 Short
mV 0~100mV 20~100mV - - S3 & S4 Short
2) DC1030
R1
R4 R2
S1 S4 R5 R3
S2
S3
S5
11 12 13 14
Input Code S1 to S5
Input Type R1 to R5
AN 4 AN 5 Jumper Status
0~20 mA
mA R3 = 100 R5 = 2.4 S3 & S5 Short
4~20 mA
0~1 V R1 = 2 K S1 & S4 Short
V 0~5 V 1~5 V R2 = 10 K R4 = 100 S2 & S4 Short
0~10 V 2~10 V R3 = 22 K S3 & S4 Short
mV 0~100mV 20~100mV - - S3 & S4 Short
3) DC1020/1040
R1
R4 R2
S1 S4 R5 R3
S2
S3 S5
17 18 19 20
Input Code S1 to S5
Input Type R1 to R5
AN 4 AN 5 Jumper Status
0~20 mA
mA R3 = 100 R5 = 2.4 S3 & S5 Short
4~20 mA
0~1 V R1 = 2 K S1 & S4 Short
V 0~5 V 1~5 V R2 = 10 K R4 = 100 S2 & S4 Short
0~10 V 2~10 V R3 = 22 K S3 & S4 Short
mV 0~100mV 20~100mV - - S3 & S4 Short
Input Code
Input Type
AN 1 AN 2 AN 3 AN 4 AN 5
mV -10~10mV 0~10mV 0~20mV 0~50mV 10~50mV
4. Calibration Procedure
Check if it shows the ANL1 and ANH1 on CONFIGURATION2. (Go to step 4-3.)
If the parameters are not shown, go to below steps.
4-1. Unlock the protection
Go to ‘LCK’ parameter on CONFIGURATION 1.
(1-1) Press the SET key for 5 seconds. It will show P1 on CONFIGURATION 1.
5seconds
5seconds
Step (1-4)
(1-2) Press the SET key until it will show LCK parameter.
(1-3) Input ‘1111’ to LCK parameter by using up/down and shift key.
(1-4) Press the SET and shift key for 5 seconds at ‘step (1-3)’. It shows ‘SET1’ of Step (2-1).
4-2. Show the parameters
Modify parameter of ‘CONFIGURATION 3’
SET2.4
SET2.3
SET2.2
SET2.1
Step (2-3)
(2-1) Press the SET key just one time until it will shows ‘SET2’.
(2-2) Change the first value of left side to 1. (SET2.2 = 1)
In case of RSP(Input2), SET2.4=1.(It shows ANL2, ANH2.)
(2-3) Press the SET and shift key for 5 seconds and return to OPERATION.
4-3. How to Calibrate
(3-1) Preparation of sources
- DC Current source : DC 0~20mA or 4~20mA
- DC voltage source : DC 0~1V, 0~5V, 0~10V, 1~5V, 2~10V
(3-2) Press the SET and shift key for 5 seconds, it will show ‘INP1’ of Configuration2.
Set INP1 to ‘AN5’ in case of DC 4~20mA.(Refer to INPUT CODE of ‘Linear input H/W setting’)
(3-3) Press the SET key just one time to show ANL1 parameter.
(3-4) Connect input source with INP1 terminals according to wiring diagram.
(3-5) Adjust the calibration values for Lower side(ANL1) and Upper side(ANH1).
PV
Adjust SP, until ‘PV=LSPL’
Press ‘ ’ key, adjust ‘ANL1’
SP (In case of this, PV=0)