Professional Documents
Culture Documents
Aquaarm Tarmat-P: Waterproofing
Aquaarm Tarmat-P: Waterproofing
Aquaarm Tarmat-P: Waterproofing
AquaArm Tarmat-P
(Formerly known as MYK Tarmat)
Product Description
AquaArm Tarmat-P is a uniquely formulated, prepre-fabricated, plastomeric waterproofing
aterproofing membrane that is developed by
modifying bitumen with APP polymer; with a homogenous th thermoplastic
ermoplastic bituminous blend of distilled asphalt, modified
with selected high grade APP (Atactic Polypropylene) polymer and inert ffillers
illers which gives the membrane
me its excellent
properties of resistance to ageing, facilitates the ease of application and adhesadhesion
ion and accommodates structural
movements. The membrane conforms to the requirement of ASTM Standards (ASTM D 5147) 5147).
Confirms BS 8102: 2009 & IS 16471: 2017 Type A waterproofing system
Application Method
Step no 1: Surface Preparation: and 100mm overlaps at ends. JointsJ should shed water
towards drains. The membrane is then rolled back without
The surface to be waterproofed must be completely clean changing the given orientation. They are then unrolled
& free of dust, oil, protruding nibs etc. Clean
lean the surface once again while heating the underside sufficiently to
using wire brush, or mechanical cleaning. Pond test the cause surface melting. End laps should be a minimum
substrate to identify the cracks and leaks and grout the 100 mm. Avoid excessive and uneven application of heat.
same with either low viscous epoxy grout ArmGrout The lap joint should be heated from
fr the top to produce a
Inject EP or cementitious ous grout additive ArmGrout thin bed d of molten bitumen at the seam; the bead is then
Additive. Cove the wall-floor
oor corners with 50mmX50mm smoothened
othened out with the trowel, ensuring a properly
fillet by using C:M 1:3 by admixing AquaArm IWP10
IWP10asper welded joint. The membranes shall be finally coated with
the recommendation of dosage. All the Bituminous Aluminium Paint for non-trafficable roofs or
construction/expansion/lift joints if any, are to be treated shall be protected with screed of avg.75mm
avg.75 thickness
as per the methodology recommended by our team. /tiles looselylaid or fixed. When being applied at
terraces/podiums/below grade application or any other
Step no 2: Priming: horizontal application being done, the membrane needs to
be taken min 300mm above the FFL on the verticals and
On a completely dry substrate apply a coat of AquaArm to be terminated either in grooves or by using aluminium
TarPrimer- a solvent base bituminous primer @ 0.3- termination bar.
0.4kgs/sqm,
kgs/sqm, dosage varies depending on the surface
conditions.. The primer must be allowed to dry completely
before application of the membrane.
Ver3/Apr 2019 1 of 3
W ATERPROOFING
AquaArm Tarmat-P
(Formerly known as MYK Tarmat)
Technical Data
Typical Values
Test
Properties
2mm 2mm 3mm 4mm Standards
Ver3/Apr 2019 2 of 3
W ATERPROOFING
AquaArm Tarmat-P
Reinforced Thermoplastic
(Formerly known as MYK Tarmat)Polyolefin Flexible
Polypropylene Alloy based waterproofing membrane
APP modified Polyester Reinforced Bituminous
Waterproofing Membrane
TECHNICAL DATA SHEET
4mmX1mX10m
Legal Note
The information, and, in particular, the recommendations relating to the application and end end-use
use of MYK Arment products, are given in
good faith based on MYK Arment current knowledge and experience of the products when pro properly
perly stored, handled and applied under
normal conditions in accordance with MYK Arment's recommendations. In practice, the difference in materials, substrates and actual site
conditions are such that no warranty in respect of merchant ability or of fitnefitness
ss for a particular purpose, nor any liability arising out of any
legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice
offered. the user of the product must test the prod
product's
uct's suitability for the intended application & purpose. MYK Arment reserves the right to
change the properties of its products. The proprietary rights of third parties must be observed. All orders are accepted subj subject to our
current terms of sale and delivery.
ivery. Users must always refer to the most recent issue of the local product data sheet for the product
concerned, copies of which will be supplied on request.
Ver3/Apr 2019 3 of 3