Professional Documents
Culture Documents
CAT6219 500 Ma Cmos Ldo Regulator: Description
CAT6219 500 Ma Cmos Ldo Regulator: Description
CAT6219 500 Ma Cmos Ldo Regulator: Description
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 11 of this data sheet.
OFF ON EN ADJ
OFF ON EN BYP
ǒ Ǔ
GND CBYP (Optional) GND
R R2
10 nF V OUT + 1.24 V 1) 1
R2
Table 1. PIN DESCRIPTIONS EN is the enable control logic (active high) for the regulator
output. It has a 2.5 MW pull−down resistor, which assures
Name Function
that if EN pin is left open, the circuit is disabled.
VIN Supply voltage input.
VOUT is the LDO regulator output. A small 2.2 mF ceramic
GND Ground reference. bypass capacitor is required between the VOUT pin and
EN Enable input (active high); a 2.5 MW pull−down ground. For better transient response, its value can be
resistor is provided. increased to 4.7 mF.
BYP Optional bypass capacitor connection for noise The capacitor should be located near the device. For the
reduction and PSRR enhancing. SOT23-5 package, a continuous 500 mA output current may
ADJ Adjustable input. Feedback pin connected to turn-on the thermal protection. A 250 W internal shutdown
resistor divider. switch discharges the output capacitor in the no-load
VOUT LDO Output Voltage. condition.
TAB To be connected to the ground plane on PCB GND is the ground reference for the LDO. The pin must be
connected to the ground plane on the PCB.
Pin Function BYP is the reference bypass pin. An optional 0.01 mF
VIN is the supply pin for the LDO. A small 1 mF ceramic capacitor can be connected between BYP pin and GND to
bypass capacitor is required between the VIN pin and ground reduce the output noise and enhance the PSRR at high
near the device. When using longer connections to the power frequency.
supply, CIN value can be increased without limit. The ADJ is the adjustable input pin for the adjustable LDO. The
operating input voltage range is from 2.3 V to 5.5 V. pin is connected to the resistor voltage divider.
Table 2. ABSOLUTE MAXIMUM RATINGS
Parameter Rating Unit
VIN 0 to 6.5 V
VEN, VOUT −0.3 to VIN + 0.3 V
Junction Temperature, TJ +150 _C
Power Dissipation, PD Internally Limited (Note 1) mW
Storage Temperature Range, TS −65 to +150 _C
Lead Temperature (soldering, 5 sec.) 260 _C
ESD Rating (Human Body Model) 3 kV
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 3. RECOMMENDED OPERATING CONDITIONS (Note 2)
Parameter Range Unit
VIN 2.3 to 5.5 V
VEN 0 to VIN V
Junction Temperature Range, TJ −40 to +125 _C
Package Thermal Resistance, θJA SOT23−5 235 _C/W
Package Thermal Resistance, θJA TDFN−6 206
NOTE: Typical application circuit with external components is shown above.
1. The maximum allowable power dissipation at any TA (ambient temperature) is PDmax = (TJmax − TA)/qJA. Exceeding the maximum allowable
power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown.
2. The device is not guaranteed to work outside its operating rating.
http://onsemi.com
2
CAT6219
http://onsemi.com
3
CAT6219
3.0 2.87
0.1 mA
2.5
500 mA 2.86
OUTPUT VOLTAGE (V)
2.83
0.5
0 2.82
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 2.5 3.0 3.5 4.0 4.5 5.0 5.5
INPUT VOLTAGE (V) INPUT VOLTAGE (V)
Figure 3. Dropout Characteristics Figure 4. Line Regulation
2.95 2.87
2.86
OUTPUT VOLTAGE (V)
2.90
2.85
2.85
2.84
2.80
2.83
2.75 2.82
0 50 100 150 200 250 300 350 400 450 500 −40 −20 0 20 40 60 80 100 120 140
OUTPUT LOAD CURRENT (mA) TEMPERATURE (°C)
Figure 5. Load Regulation Figure 6. Output Voltage vs. Temperature
70 65
60
61
GROUND CURRENT (mA)
50
40 57
30 53
20
49
10
0 45
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 −40 −20 0 20 40 60 80 100 120 140
INPUT VOLTAGE (V) TEMPERATURE (°C)
Figure 7. Ground Current vs. Input Voltage Figure 8. Ground Current vs. Temperature
http://onsemi.com
4
CAT6219
100
90
GROUND CURRENT (mA)
80
70
60
50
0 50 100 150 200 250 300 350 400 450 500
OUTPUT LOAD CURRENT (mA)
Figure 9. Ground Current vs. Load Current
500 400
500 mA DROPOUT VOLTAGE (mV)
350
450
DROPOUT VOLTAGE (mV)
300
400
250
350 200
150
300
100
250
50
200 0
−40 −20 0 20 40 60 80 100 120 140 0 50 100 150 200 250 300 350 400 450 500
TEMPERATURE (°C) OUTPUT LOAD CURRENT (mA)
Figure 10. Dropout vs. Temperature Figure 11. Dropout vs. Load Current
(500 mA Load)
1.6 80
70
CBYP = 10 nF
ENABLE THRESHOLD (V)
1.2 60
CBYP = 0
50
PSRR (dB)
0.8 40
30
0.4 20
10
0 0
2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 1.0E+01 1.0E+02 1.0E+03 1.0E+04 1.0E+05
INPUT VOLTAGE (V) FREQUENCY (Hz)
Figure 12. Enable Threshold vs. Input Voltage Figure 13. PSRR vs. Frequency (10 mA Load)
http://onsemi.com
5
CAT6219
Figure 14. Enable Turn−on (100 mA Load) Figure 15. Enable Turn−off (100 mA Load)
Figure 16. Enable Turn−on (500 mA Load) Figure 17. Enable Turn−off (500 mA Load)
Figure 18. Line Transient Response Figure 19. Load Transient Response
(3.85 V to 4.85 V) (0.1 mA to 500 mA)
http://onsemi.com
6
CAT6219
+ + ADJ
− −
GND GND
Figure 20. Block Diagram − Fixed Voltage Figure 21. Block Diagram − Adjustable Voltage
http://onsemi.com
7
CAT6219
PACKAGE DIMENSIONS
TSOT−23, 5 LEAD
CASE 419AE−01
ISSUE O
A2 A
q
L
b A1 c L2
L1
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-193.
http://onsemi.com
8
CAT6219
PACKAGE DIMENSIONS
TDFN6, 2x2
CASE 511AH−01
ISSUE A
D A
DETAIL A
PIN#1
IDENTIFICATION
e
SYMBOL MIN NOM MAX
A 0.70 0.75 0.80
A1 0.00 0.02 0.05
b L
A3 0.20 REF
DETAIL A
b 0.25 0.30 0.35
D 1.90 2.00 2.10
D2 1.50 1.60 1.70
E 1.90 2.00 2.10
A
E2 0.90 1.00 1.10
e 0.65 TYP
L 0.15 0.25 0.35 A1 A3
FRONT VIEW
Notes:
(1) All dimensions are in millimeters.
(2) Complies with JEDEC standard MO-229.
http://onsemi.com
9
CAT6219
PACKAGE DIMENSIONS
D A L NOTES:
1. DIMENSIONING AND TOLERANCING PER
B ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
L1 3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30mm FROM TERMINAL TIP.
DETAIL A 4. COPLANARITY APPLIES TO THE EXPOSED
ÍÍÍÍ
ALTERNATE TERMINAL PAD AS WELL AS THE TERMINALS.
E CONSTRUCTIONS
ÍÍÍÍ
PIN ONE MILLIMETERS
REFERENCE DIM MIN MAX
ÍÍÍÍ ÉÉÉ ÉÉ
A 0.70 0.80
A3 A1 0.00 0.05
2X 0.10 C EXPOSED Cu MOLD CMPD A3 0.20 REF
ÉÉÉ ÉÉ
ÇÇ
b 0.20 0.30
D 1.50 BSC
2X 0.10 C
TOP VIEW E 1.50 BSC
e 0.50 BSC
A1 L 0.40 0.60
DETAIL B
0.05 C A3 DETAIL B L1 --- 0.15
ALTERNATE L2 0.50 0.70
CONSTRUCTIONS
A GENERIC
MARKING DIAGRAM*
0.05 C
A1 1
NOTE 4
X MG
SIDE VIEW C SEATING
PLANE G
6 4
RECOMMENDED
6X b MOUNTING FOOTPRINT*
0.10 C A B 5X
6X 0.35 0.73
0.05 C NOTE 3
BOTTOM VIEW
1.80
0.83 0.50
PITCH
DIMENSIONS: MILLIMETERS
http://onsemi.com
10
CAT6219
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
http://onsemi.com CAT6219/D
11