Professional Documents
Culture Documents
Client Project Title Scale at A1 Drawing Title
Client Project Title Scale at A1 Drawing Title
Client Project Title Scale at A1 Drawing Title
450 max
bricks in 1:3 cement mortar
bedded on 1 to 3 courses
of Class B engineering
max
450
150mm (min) grade
450 max
Cover slab shall be bricks in 1:3 cement mortar
C16/20 concrete surround
heavy duty biscuit Heavy duty cover slab
150mm (min) grade
Lifting holes in precast C16/20 concrete surround
concrete units shall be Heavy duty cover slab
max
300
cleaned and filled with
150
1:3 cement mortar
300 max
2 concrete benching with 1:6 CL.804 backfill material
gradient to channel around chamber compacted
Round bar double step irons in layers of 250mm max CL.804 backfill material
300 max
built into chamber around chamber compacted
in layers of 250mm max
Bedded and haunched with Rodding pooint to be capped
cement mortar 75mm Reducing slab
above base of ring
50
max
300
CL.804 backfill material
around chamber compacted Reducing slab
Precast concrete
in layers of 250mm max ring section
Rough benching to be C25/30
concrete benching to be min
3 Precast concrete
325mm and 450mm wide
Round bar double step ring section 150mm (min) grade
75mm concrete blinding irons built into manhole First rocker pipe joint to C16/20 concrete surround
be within 150mm of Round bar double step
Base slab 225mm thick(min) of external face of chamber
C16/20 concrete with 1 layer irons
for pipes up to and
A393 mesh extended to 50mm
Section above crown of highest pipe 25mm thick granolithic within 300mm for pipes
after pipe laying concrete benching with
1:6 gradient to channel to be within 750mm refer 25mm thick granolithic
to table for rocker pipe concrete benching with
lenghts 1:6 gradient to channel
4
Rough benching to be 150mm (min) grade
C25/30 concrete. Benching C16/20 concrete surround
to be min. 325mm and
First rocker pipe joint to be Rough benching to be
150mm(min) surround of C16/20 450mm wide
within 150mm of external face C25/30 concrete. Benching
of chamber for pipes up to and concrete to be min. 325mm and
Bend to direct drainage
450mm wide
into flow of channel
second joint to be within 750mm
Rocker length as per table
225 (min) C16/20 concrete
75mm concrete blinding base with 1 layer A393 mesh 75mm concrete blinding
5
integral with manhole surround
Plan
Manhole Sizes
450mm
Manhole covers and frames to comply with the requirements of IS/EN 124:1994. covers edge of the channel to a height not less than that of the soffit of the outlet and
slope upwards to meet the wall of the manhole at a gradient of 1:6 (min. rise 25mm).
shall be the EJ covers Noroc cover unless noted otherwise.
605mm
605mm
It should be floated with a steel float to a smooth hard surface with a 25mm thick
coat of 1:1 cement mortar laid while the benching concrete is still green.
635mm
End Elevation
Detail A
18mm min waterproof flexible
9 sheeting at each pipe joint
Y
Spigot and socket joint Concrete
Bed &
Haunch
Minimum
Compressive
2
Z Strength
C20/25
Pavement or haunch
Channel
(construction varies)
150mm Concrete bedding wall
X
Installation Detail A
Typical Drainage Channel Detail Typical Drainage Channel Sump Detail
10
Construction Detail for Concrete Bed Scale: 1:10
Scale: 1:10
Scale at A1
Client Project Title Drawing Title As Shown
Role
Site Infrastructure
Ringaskiddy Resource Typical Drainage Details
Recovery Centre Sheet 1 of 2 Suitability
Planning
Arup Job No Rev
15 Oliver Plunkett Street
PL1 11/12/15 J.B. J.B. JMacC Cork, Ireland
Tel +353 (0)21 427 7670 Fax +353 (0)21 427 2345
238129-00 PL1
www.arup.com Name
Issued for Planning
Rev Date By Chkd Appd C-000-080
Do not scale