Professional Documents
Culture Documents
ATV310 Getting Started Parameters EN EAV96136 05
ATV310 Getting Started Parameters EN EAV96136 05
EAV9613605
Reference mode F007 Internal thermal sensor fault [01] negative 217 Speed Template [03] Remote display
I/O menu
Reference menu
402 External reference value F008 Internal CPU 204- AI1 CONFIGURATION MENU [00]* Standard [10] Modbus
403 Analog input virtual F009 Overbraking 204.0 AI1 type [02] DeadBand 408 Forced local assignment
F010 Overcurrent [5U]* Voltage: 0-5Vdc 300- MOTOR CONTROL MENU [00]* No: Function inactive
801 Speed reference [L1H] LI1 active High
801 Speed reference F017 Input phase loss 0-20mA (20mA*) 0.5 to 1 (depending on drive rating) [01] Terminal
1 3
[00] Drive ready F029 Process underload [08] Motor thermal reached 309 Motor control type
[21] Underload alarm [01] S shape
[01] Drive running F030 Undervoltage [00] Performance: Vector control [02] U shape
[02] Acceleration [22] Overload alarm [03]* Standard: U/F 2 points 501.3 Ramp switching commutation
F031 Incorrect configuration [123] Loss of 4-20mA signal
[03] Deceleration F032 Invalid configuration [06] Pump: U²/F [00]* Not assigned
[04] DC injection braking in progress F033 AI1 current loss 206- LO1 CONFIGURATION MENU 310 IR compensation [L1H] LI1 active High
206.0 LO1 Assignment 25 to 200% (100%*)
Drive status
2 4
N4 [5U]* 0-5V 20 to 100% of nominal motor current (60%*) [01] Yes [L2L] LI2 active Low to stop
906 Specific Product Number [10U] 0-10V 212 Underload fault duration 321 Max voltage of constant power [L3L] LI3 active Low to stop
907 Card 1 Software Version [0A] x-y mA 0 to 6min (0min*) [L4L] LI4 active Low to stop
Maintenance menu
Control menu
403 Analog input virtual
Macro
reverse direction
[01]* Yes: Stop active
I/O menu
202 2-wire type control [140] Motor thermal state [L1H] LI1 active High
F002 Unknown drive rating [141] Drive thermal state 406 Channel configuration [L2H] LI2 active High
Function
F003 Unknown or incompatible power board [00] level [01]* Not separate mode
[01]* transition 216.1 AOI type [L3H] LI3 active High
F004 Internal serial link [02] Forward priority [02] Separate mode [L4H] LI4 active High
[10U] Voltage: 0-10 Vdc 407 Command channel 1
F005 Invalid industrialization zone 203 Logic inputs type [0A]* Current: 0-20 mA [LUH] LIU active High
F006 Current measurement circuit [00]* positive [01]* Terminals 504- AUTO DC INJECTION MENU
[4A] Current: 4-20 mA [02] Local
The (*) indicates a parameter factory setting.
www.schneider-electric.com 1/2
Easy Altivar ATV310 complete parameters list
504.0 Automatic DC injection 59- PID MENU 59.24 Maximum frequency detection Hysteresis 512.4 4 High speed assignment 610 Detected fault inhibition assignment
DC injection function
line interrup.
0.1 to 30s (0.5s*) 0.01 to 100 (1*) 0 to High speed (0Hz*)
505 Jog assignment 59.03 PID derivative gain 510- PUMP SUB-MENU Low speed to Max frequency (50 or 60Hz*) [00]* Detected fault ignored
[00]* Not assigned 0.00 to 100.0 (0*) 207 Overload time delay 512.6 High speed 3 [01] Freewheel stop
[L1H] LI1 active High 59.04 PID feedback scale factor Low speed to Max frequency (50 or 60Hz*) 612 Degraded line supply operation
Jog function
0 to 100 s (0 s*)
[L2H] LI2 active High 0.1 to 100.0 (1.0*) 208 Overload threshold 512.7 High speed 4 [00]* No
[L3H] LI3 active High 59.05 Activation internal PID reference 70 to 150% of nominal motor current (90%*) Low speed to Max frequency (50 or 60Hz*) [01] Yes
[L4H] LI4 active High [00]* No 209 Overload fault duration 513 Cooling fan control 613 Reset power run
Fan
[LUH] LIU active High [01] Yes 0 to 6 min (0 min*) [00] Fan runs when drive runs [00]* No
7
0 to 6min (0min*) [L2H] LI2 active High
5
[L4H] LI4 active High [LUH] LIU active High 510.0 Selecting operating mode [L3H] LI3 active High [01] Active
[LUH] LIU active High 59.07 4 preset PID assignment [00]* Single frequency conversion mode [L4H] LI4 active High 700- COMMUNICATION MENU
506.1 Down speed command [00]* Not assigned [01] Single frequency conversion combined [LUH] LIU active High 701 Modbus address
[00]* Not assigned [L1H] LI1 active High with auxiliary pump mode 602- AUTOMATIC RESTART MENU Off to 247 (off*)
[L1H] LI1 active High [L2H] LI2 active High 510.1 Starting frequency of the auxiliary pump 602.0 Automatic restart 702 Modbus baud rate
Motor potentiometer function
[L2H] LI2 active High [L3H] LI3 active High 0 to 60Hz (50Hz*) [00]* No [24] 4.8 kbps
Automatic restart
510.2 Time delay before starting auxiliary pump [01] Yes [28] 9.6 kbps
[L4H] LI4 active High [LUH] LIU active High 0 to 999.9s (2s*) 602.1 Max. automatic restart [32]* 19.2 kbps
[LUH] LIU active High 59.08 2 preset PID reference 510.3 Auxiliary pump ramp reaching [00]* 5 min [36] 38.4 kbps
506.2 Store 0 to 100% (25%*) 0 to 999.9s (2s*) [01] 10 min 703 Modbus format
[00]* No 59.09 3 preset PID reference 510.4 Auxiliary pump stop frequency [02] 30 min [02] 8o1
[01] RAM 0 to 100% (50%*) 0 to 60Hz (0Hz*) [03] 1 hour [03]* 8E1
[02] ROM 59.10 4 preset PID reference 510.5 Auxiliary pump stop time delay [04] 2 hours [04] 8n1
506.3 Clear the function 0 to 100% (75%*) 0 to 999.9s (2s*) [05] 3 hours [05] 8n2
PID Control function
[00]* Not assigned 59.11 Internal PID reference 510.6 Auxiliary pump stop ramp [06] Infinite 704 Modbus time out
[L1H] LI1 active High 0 to 100% (0%*) 0 to 999.9s (2s*) 603 Catch on the fly 0.1 to 30s (10s*)
Catch on
the fly
[L2H] LI2 active High 59.12 PID reference ramp 510.7 Zero flow detection period [00]* Function inactive 705- INPUT SCANNER MENU
[L3H] LI3 active High 0 to 100% (0%*) 0 to 20min (0min*) [01] Function active 705.0 Com scanner read adress parameter 1
[L4H] LI4 active High 59.13 PID min value reference 510.8 Zero flow detection activation threshold 604- MOTOR THERMAL PROTECTION MENU 0C81*
[LUH] LIU active High 0 to 100% (0%*) 0 to 400Hz (0Hz*) 604.0 Motor thermal current 705.1 Com scanner read adress parameter 2
[159] Acceleration and deceleration with com-
Communication menu
[00]* Not activated [00] Detected fault ignored
507.0 2 Preset speeds 0.0 to 999.9s (5s*) [L1H] LI1 active High 706- OUTPUT SCANNER MENU
[00]* Not assigned 59.16 PID correction reverse [01]* Free wheel stop
[L2H] LI2 active High 604.3 Motor thermal state memo 706.0 Com scanner write adress parameter 1
[L1H] LI1 active High [00]* No, no negative speed [L3H] LI3 active High 2135*
[L2H] LI2 active High [01] Yes, no negative speed [00]* thermal state not stored at power off
[L4H] LI4 active High [01] thermal state is stored at power off 706.1 Com scanner write adress parameter 2
6 8
[L3H] LI3 active High [02] No, allow negative speed [LUH] LIU active High 219A*
[L4H] LI4 active High [03] Yes, allow negative speed 605 Output Phase loss
[L1L] LI1 active Low [00] Deactivated 706.2 Com scanner write adress parameter 3
[LUH] LIU active High 59.17 PID auto/manual assignment [L2L] LI2 active Low
Phase loss
[01]* Tripping then freewheel stop 0000
507.1 4 Preset speeds [00]* Not assigned [L3L] LI3 active Low 706.3 Com scanner write adress parameter 4
same as 2 Preset speeds [L1H] LI1 active High 606 Input Phase loss
[L4L] LI4 active Low [00] Detected fault ignored 0000
507.2 8 Preset speeds [L2H] LI2 active High [LUL] LIU active Low 707- INPUT SCANNER ACCESS MENU
Maintenance menu
same as 2 Preset speeds [L3H] LI3 active High [01]* Detected fault with freewheel stop
511.1 Current limitation 607- UNDERVOLTAGE MENU 707.0 Com scanner read adress value 1
507.3 Preset speed 2 [L4H] LI4 active High 0.25 to 1.5In (1.5In*)
[LUH] LIU active High 607.0 Undervoltage detected fault management 0C81*
0 to 400Hz (10Hz*) 511.2 Current limitation 2 707.1 Com scanner read adress value 2
507.4 Preset speed 3 59.18 PID manual reference [00]* Detected fault and R1 relay open
0.25 to 1.5In (1.5In*)
Undervoltage
[00]* No [01] Detected fault and R1 relay closed 219C*
0 to 400Hz (15Hz*) 512- SPEED LIMIT MENU 607.1 Undervoltage prevention 707.2 Com scanner read adress value 3
507.5 Preset speed 4 [01] Yes [00]* No action (freewheel)
[183] Integrated jog dial 512.0 Low speed 0000
0 to 400Hz (20Hz*) 0Hz to high speed (0Hz*) [02] Stop following an adjustable ramp 707.3 Com scanner read adress value 4
Speed limitation function
507.6 Preset speed 5 512.1 Low speed operating time 607.2 Undervoltage ramp deceleration time
0.1 to 999.9s (0s*) 512.1 Low speed operating time 0000
0 to 400Hz (25Hz*) 0.1 to 999.9s (0s*) 0.0 to 10.0s (1.0s*)
507.7 Preset speed 6 59.19 PID: wake up level 708- OUTPUT SCANNER ACCESS MENU
512.2 High speed 607.3 Precharge resistor protection level 708.0 Com scanner write adress value 1
0 to 400Hz (30Hz*) 0 to 100% (0%*) 430 to 560 VDC (0 V* with protection removed)
Low speed to maximum frequency (50 or 60Hz CMD value*
507.8 Preset speed 7 according to standard motor frequency*) 608 IGBT test
0 to 400Hz (35Hz*) 59.20 PID: Wake up threshold 708.1 Com scanner write adress value 2
IGBT
512.3 2 High speed assignment [00]* No test
507.9 Preset speed 8 0 to 100% (0%*) [01] Starting test LFRD value*
59.21 Sleep offset threshold [00]* Not assigned 708.2 Com scanner write adress value 3
0 to 400Hz (40Hz*) [L1H] LI1 active High 609 4-20mA loss Behaviour
508 Skip frequency 0 to High speed (0Hz*) [00]* Detected fault ignored 8000
59.22 PID feedback supervision threshold [L2H] LI2 active High 4-20 mA loss 708.3 Com scanner write adress value 4
0 to 400Hz (0Hz*) [01] Freewheel stop
frequency
59.23 PID supervision function time delay [L4H] LI4 active High
0 to 300s (0s*) [LUH] LIU active High