Professional Documents
Culture Documents
DL CoMP (FDD) (eRAN13.1 - 05)
DL CoMP (FDD) (eRAN13.1 - 05)
Issue 05
Date 2018-11-07
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
Contents
1 Change History.............................................................................................................................. 1
1.1 eRAN13.1 05 (2018-11-07)............................................................................................................................................1
1.2 eRAN13.1 04 (2018-08-27)............................................................................................................................................1
1.3 eRAN13.1 03 (2018-07-28)............................................................................................................................................2
1.4 eRAN13.1 02 (2018-06-30)............................................................................................................................................2
1.5 eRAN13.1 01 (2018-04-10)............................................................................................................................................2
1.6 eRAN13.1 Draft B (2018-03-30)....................................................................................................................................3
1.7 eRAN13.1 Draft A (2018-01-15)................................................................................................................................... 3
3 Overview......................................................................................................................................... 5
3.1 Introduction.................................................................................................................................................................... 5
3.2 Related Concepts............................................................................................................................................................ 7
3.3 Architecture.................................................................................................................................................................... 7
4 DL CoMP.........................................................................................................................................9
4.1 Principles........................................................................................................................................................................ 9
4.1.1 Selection of a Coordinating Cell Set........................................................................................................................... 9
4.1.2 Selection of CoMP UEs and Coordinating Cells.......................................................................................................10
4.1.2.1 Entering the DPS Mode.......................................................................................................................................... 10
4.1.2.2 Entering the JT Mode............................................................................................................................................. 11
4.1.2.3 Exiting the DPS or JT Mode...................................................................................................................................12
4.1.3 Multi-Cell Coordinated Transmission....................................................................................................................... 12
4.2 Network Analysis......................................................................................................................................................... 13
4.2.1 Benefits...................................................................................................................................................................... 13
4.2.2 Impacts.......................................................................................................................................................................13
4.3 Requirements................................................................................................................................................................ 16
4.3.1 Licenses..................................................................................................................................................................... 16
4.3.2 Software.....................................................................................................................................................................16
4.3.3 Hardware................................................................................................................................................................... 18
4.3.4 Networking................................................................................................................................................................ 19
4.3.5 Others.........................................................................................................................................................................19
5 Parameters..................................................................................................................................... 30
6 Counters........................................................................................................................................ 86
7 Glossary......................................................................................................................................... 95
8 Reference Documents................................................................................................................. 96
1 Change History
This chapter describes changes not included in the "Parameters", "Counters", "Glossary", and
"Reference Documents" chapters. These changes include:
l Technical changes
Changes in functions and their corresponding parameters
l Editorial changes
Improvements or revisions to the documentation
Technical Changes
None
Editorial Changes
Revised descriptions in the following sections:
Technical Changes
None
Editorial Changes
Revised descriptions in 4.3.3 Hardware.
Technical Changes
None
Editorial Changes
Revised descriptions in 4.3.2 Software.
Technical Changes
None
Editorial Changes
Revised descriptions in the following sections:
l 4.2.2 Impacts
l 4.3.2 Software
Technical Changes
Change Description Parameter Change Base Station Model
Editorial Changes
Revised descriptions in 4.2.2 Impacts.
Technical Changes
None
Editorial Changes
Added deactivation command examples. For details, see 4.4.1.2 Using MML Commands.
Technical Changes
None
Editorial Changes
Reorganized this document using a new template.
3 Overview
3.1 Introduction
In 3GPP releases earlier than 3GPP Release 11, physical downlink shared channel (PDSCH)
data of LTE cell edge users (CEUs) cannot be sent with the help of adjacent cells to improve
the performance of CEUs. This gain can be achieved by downlink coordinated multipoint
transmission (DL CoMP) based on TM10 introduced in 3GPP Release 11.
DL CoMP enables multiple cells to cooperate to perform downlink transmission. DL CoMP is
implemented based on TM10 introduced in 3GPP Release 11. Multiple cells cooperate based
on ideal backhaul (intra-BBU backhaul or backhaul based on multi-BBU interconnection
through USUs) to process and transmit PDSCH data by using antennas of neighboring cells.
USU refers to universal switching unit. Downlink transmission by multiple cells adopts two
modes, dynamic point selection (DPS) and joint transmission (JT), to improve hotspot cell
capacity or CEU performance. eNodeBs can adaptively select an appropriate transmission
mode based on the cell load and channel quality.
DPS
In DPS mode, the coordinating cell sends PDSCH data to the UE to increase the hotspot cell
capacity, CEU throughput, and average UE throughput.
Figure 3-1 illustrates the DPS mode, in which PDCCH data of the UE is sent by cell 1 (the
serving cell), and PDSCH data is sent by cell 1 to cell 2 (the coordinating cell) and then sent
by cell 2 to the UE.
JT
In JT mode, both the serving cell and coordinating cell transmit PDSCH data to improve the
throughput of CEUs with a low signal to interference plus noise ratio (SINR).
Figure 3-2 illustrates the JT mode, in which
l PDCCH data of the UE is sent by cell 1 (the serving cell), and PDSCH data is sent by
cell 1 to cell 2 (the coordinating cell). Cell 1 and cell 2 allocate the same RBs to send
PDSCH data to the UE.
l The UE receives the same PDSCH data from cell 1 and cell 2 simultaneously.
Figure 3-2 JT
Coordinating cell A set of 10 neighboring cells that cause the strongest interference to
set of the serving the serving cell as measured by the eNodeB
cell
Coordinating cell The eNodeB identifies the coordinating cells for a DPS or JT UE
of a DPS or JT UE based on the event A3 measurement report sent by the DPS or JT UE.
The coordinating cells of a UE belong to the coordinating cell set of
the serving cell of the UE.
3.3 Architecture
DL CoMP is implemented through the cooperation of the U2000, USU, eNodeB, and UE.
Figure 3-3 to Figure 3-5 show the networking diagrams. If DL CoMP is performed among
BBUs, time synchronization is required across the entire network.
Table 3-2 describes the functions of the network elements (NEs) shown in Figure 3-3 to
Figure 3-5.
4 DL CoMP
4.1 Principles
Figure 4-1 shows the DL CoMP process, including selection of a coordinating cell set,
selection of CoMP UEs and coordinating cells, and multi-cell coordinated transmission.
As shown in Figure 4-2, when the PRB usage of the serving cell is greater than the
threshold specified by the CellDlCompAlgo.DpsServingCellDlPrbThd parameter and
the serving cell is a macro cell, the eNodeB selects the serving cell as the DPS serving
cell.
2. The eNodeB selects the cells with the strongest RSRP in the coordinating cell set as
coordinating cells.
If the RSRP of a neighboring cell of the UE minus that of the serving cell of the UE is
greater than or equal to the coordinating cell RSRP threshold plus the coordinating cell
RSRP offset, the UE reports event A3. If the neighboring cell that meets the event A3
reporting conditions belongs to the coordinating cell set, it is selected as a coordinating
cell.
– In HomNet networking scenarios, the coordinating cell RSRP threshold is specified
by the CellDlCompAlgo.HomnetDpsCoCellRsrpThd parameter, and only the
macro cells with the strongest RSRP in the coordinating cell set can be selected as
coordinating cells.
– In HetNet scenarios, the coordinating cell RSRP threshold is specified by the
CellDlCompAlgo.HetnetDpsCoCellRsrpThd parameter, and only the micro cells
with the strongest RSRP in the coordinating cell set can be selected as coordinating
cells.
– In HomNet and HetNet hybrid networking scenarios, the micro cells with the
strongest RSRP in the coordinating cell set are preferentially selected as
coordinating cells.
NOTE
The system automatically configures the coordinating cell RSRP offset to prevent ping-pong
configuration of TM10 for UEs.
3. The eNodeB selects DPS UEs.
If the coordinating cells selected in 2 meet all of the following conditions, the eNodeB
selects the UEs as DPS UEs and configures the TM10 mode for them.
– The PRB usage of the serving cell minus the PRB usage of a coordinating cell is
greater than the value of the CellDlCompAlgo.DpsLoadDiffThd parameter.
– The number of UEs in RRC_CONNECTED mode in a coordinating cell divided by
the number of UEs in RRC_CONNECTED mode in the serving cell is less than or
equal to the value of the CellDlCompAlgo.DpsCoCellUserRatioThd parameter.
The selected DPS UE is regarded as a UE in the coordinating cell.
– No PCI mod 3 conflict exists between coordinating cells and the serving cell.
plus the coordinating cell RSRP offset, and the neighboring cell belongs to the
coordinating cell set, this cell is selected as a coordinating cell.
– In HomNet networking scenarios, only the cells of the same site type as the serving
cell and with the strongest RSRP in the coordinating cell set can be selected as
coordinating cells.
– In HetNet networking scenarios, when the serving cell is a macro cell, only the
micro cells with the strongest RSRP in the coordinating cell set can be selected as
coordinating cells.
– In HomNet and HetNet hybrid networking scenarios, the cells with the strongest
RSRP in the coordinating cell set are preferentially selected as coordinating cells.
However, when the serving cell is a micro cell, only micro cells can be selected as
coordinating cells.
NOTE
The system automatically configures the coordinating cell RSRP offset to prevent ping-pong
configuration of TM10 for UEs.
3. The eNodeB selects JT UEs.
If the coordinating cells selected in 2 meet both of the following conditions, the eNodeB
selects the UEs as JT UEs and configures the TM10 mode for them.
– The PRB usage of a coordinating cell is less than the value of the
CellDlCompAlgo.JtCoCellDlPrbThd parameter.
– The spectral efficiency for the CQIs reported by the UEs is less than that for CQIs 5
and 8 in the case of single-codeword transmission. For details about CQIs 5 and 8,
see Table 7.2.3-1 4-bit CQI Table and Table 7.2.3-2 4-bit CQI Table 2 in section
7.2.3 "Channel Quality Indicator (CQI) definition" in 3GPP TS 36.213 V12.9.1.
4.2.1 Benefits
Gains
This feature improves the downlink throughput and user experience of CEUs.
l DPS increases the capacity of hotspot cells and improves the CEU throughput and
average UE throughput when the network load is heavy and imbalanced.
l JT improves the throughput of CEUs with a low SINR when the network load is light.
4.2.2 Impacts
Network Impacts
l When DPS takes effect, PDSCH data of CEUs in the heavily loaded serving cell are
offloaded to coordinating cells. In this way, more resources are available for UEs in the
serving cell, and the downlink user-perceived throughput in the serving cell increases. If
the increase of resources for DPS UEs in the lightly loaded coordinating cells cannot
compensate for the loss caused by channel quality deterioration, the downlink user-
perceived throughput of the DPS UEs decreases.
l HomNet networking: When the PRB usage of the heavily loaded cell is 60%, DL CoMP
increases the CEU throughput by 5% to 10% and the average UE throughput by up to
5%.
l HetNet networking: When a macro cell includes four micro cells and the PRB usage of
the macro cell is 60%, DL CoMP increases the CEU throughput by about 20% and the
average UE throughput by about 10%.
Function Impacts
Function Function Switch Reference Description
Name
Downlink InterFddTddCaSwitch
FDD+TDD option of the
CA CaMgtCfg.CellCaAlgoS
witch parameter
4.3 Requirements
4.3.1 Licenses
There are currently no license requirements for trial features. For details, see General
Statements.
4.3.2 Software
Prerequisite Functions
Function Function Switch Reference Description
Name
4.3.3 Hardware
Base Station Models
The following base stations are compatible with this function:
l 3900 and 5900 series base stations
l DBS3900 LampSite and DBS5900 LampSite
Boards
l BBU: The BBU3900, BBU3910, and BBU3910A support this feature. When the
BBU3910A is used, only intra-BBU DL CoMP is supported, and inter-BBU DL CoMP
is not supported.
l BBP: The LBBPc does not support this function.
l USU: A USU3910 is required when inter-BBU DL CoMP is required.
RF Modules
Micro cells in DL CoMP are those served by low-power RRUs, such as RRU3220E and
RRU3230E.
Cells
l JT: Both of the following requirements must be met:
– The Cell.CrsPortNum settings of the cells where this feature is enabled are the
same.
– Both the serving cell and coordinating cell must support 2T or 4T.
l DPS: Both the serving cell and coordinating cell must support 2T or 4T.
4.3.4 Networking
l If inter-BBU DL CoMP is used, Cloud BB achieved by USU-based multi-BBU
interconnection must be deployed.
– For details about Cloud BB networking, see Cloud BB Overview.
– For details about the networking, cable connections, and clock synchronization for
the USU3910-based Cloud BB architecture, see USU3910-based Multi-BBU
Interconnection.
l eNodeBs provide contiguous coverage with the same frequency and bandwidth. The cell
bandwidth must be greater than or equal to 5 MHz.
l If inter-BBU DL CoMP is used, time synchronization is required across the entire
network. The time synchronization accuracy between all cells with DL CoMP to be
enabled must be less than 3 μs, and GPS or IEEE1588 V2 synchronization can be used.
For details, see Synchronization.
4.3.5 Others
Among the following listed counters, counters related to CEUs are available only when the
BasedA3EdgeUserSwitch option of the CellCounterParaGroup.CellCounterAlgoSwitch
parameter is selected. CEUs can be identified based on the
CellCounterParaGroup.EdgeUserA3Offset parameter. CEUs with weak coverage can be
identified based on the CellCounterParaGroup.EdgeUserServRSRPThd parameter.
Before activating DL CoMP, run the following command:
MOD CELLCOUNTERPARAGROUP:LocalCellId=0,
CellCounterAlgoSwitch=BasedA3EdgeUserSwitch-1, EdgeUserA3Offset=-12;
This feature requires support from UEs. UEs must be compliant with 3GPP Release 11 or
later and capable of TM10 multi-CSI measurement.
To accurately evaluate whether the conditions for enabling DL CoMP are met, collect the
following information before feature deployment:
1526728969 L.Traffic.ActiveUser.DL.Avg
1526728970 L.Traffic.ActiveUser.DL.Max
1526728975 L.Traffic.ActiveUser.Avg
1526728976 L.Traffic.ActiveUser.Max
1526728262 L.Thrp.Time.DL
1526729005 L.Thrp.bits.DL.LastTTI
1526729015 L.Thrp.Time.DL.RmvLastTTI
1526737758 L.Thrp.bits.DL.LastTTI.BorderUE
1526737759 L.Thrp.Time.DL.RmvLastTTI.BorderUE
The following table describes the parameter that must be set in the CellAlgoSwitch MO to
enable DL CoMP.
The following table describes the parameters that must be set in the NCellDlRsrpMeasPara
MO for coordinating cell set measurement.
The following table describes the parameters that must be set in the CellCsiRsParaCfg MO
for the CSI-RS.
The following table describes the parameters that must be set in the CellDlschAlgo MO for
downlink scheduling.
The following table describes the parameter that must be set in the CellUlschAlgo MO for
uplink scheduling.
l All cells with this feature enabled must have the same DL CoMP configurations.
l This feature is implemented on the basis of TM10. CSI-RSs must be configured (using the
CellCsiRsParaCfg MO) in all the cells with this feature enabled.
Step 1 On the eNodeB side, run the DSP CELLDLCOMPCOCELLS command to query the value
of Cell DL CoMP Property.
Expected result: The value of Cell DL CoMP Property is DLCOMP_DPS or
DLCOMP_JT.
Step 2 Log in to the U2000 and choose Monitoring > Signaling Trace > Signaling Trace
Management. In the displayed window, choose Cell Performance Monitoring > DL CoMP
Monitoring in the navigation tree. In the displayed dialog box, select the target eNodeBs and
create a DL CoMP monitoring task that monitors the number of DL CoMP UEs in a cell that
are also scheduled in coordinating cells.
Expected result: The value of DPS Benefit User Number or JT Benefit User Number is not
zero. This result shows that this feature has taken effect.
----End
Using Counters
Observe the counters listed in the following table before and after activating this feature. The
changes in the counter values reflect feature performance.
Counter ID Counter Name
1526743727 L.Traffic.User.DLDps.Avg
1526743728 L.Traffic.User.DLJT.Avg
1526743725 L.ChMeas.PRB.DL.DPS.Used.Avg.Other
Cell
1526743726 L.ChMeas.PRB.DL.JT.Used.Avg.OtherC
ell
Observe the following indicators before and after activating this feature. The changes in the
values reflect feature gains.
Before observing the downlink average user-perceived rate and the user-perceived rate at the
cell edge, run the MOD CELLCOUNTERPARAGROUP command to turn on switches
related to cell-level performance measurement.
MML command example:
MOD
CELLCOUNTERPARAGROUP:LOCALCELLID=0,CELLCOUNTERALGOSWITCH=BasedA3EdgeUserSwitch-1,E
DGEUSERA3OFFSET=-12;
Step 1 Run the LST CELLALGOSWITCH command to check whether the DL CoMP algorithm
switch is turned on.
l If yes, go to Step 2.
l If no, configure parameters by referring to 4.4.1.1 Data Preparation.
Step 2 Run the DSP CELLDLCOMPCOCELLS command to check whether DL CoMP has taken
effect.
l If yes, check whether there is a coordinating cell list.
– If yes, go to Step 3.
– If no, check whether intra-frequency neighbor relationships have been established
between the local cell and neighboring cells. Check whether there are CEUs in the
cell by observing the L.Traffic.User.BorderUE.Avg counter. Check whether the
DL CoMP switch has been turned on for more than one hour.
l If no, check whether the local cell meets the DL CoMP threshold criteria, including user
proportion thresholds for CSI-RS configuration and unconfiguration and the PRB usage
threshold.
Step 3 Check the following performance counters to see whether the DPS or JT UE proportion is too
low, for example, lower than 15%.
Counter ID Counter Name Description
l If no, go to Step 4.
l If yes, the number of DPS and JT UEs is too small. In this case, DL CoMP cannot offer
noticeable gains to increase the capacity in terms of UE quantity and data rate.
Step 4 If the preceding steps fail to resolve the problem, contact Huawei technical support.
----End
5 Parameters
NCellDl DlRsrp MOD LOFD-0 Coordin Meaning: Indicates whether automatic measurement
RsrpMe AutoNC NCELL 70208 ated of downlink RSRP in neighboring cells is supported
asPara ellMeas DLRSR LAOFD Scheduli by the local cell. If this parameter is set to ON,
Switch PMEAS -120201 ng based automatic measurement of downlink RSRP in
PARA Power neighboring cells takes effect. If this parameter is set
LST Control to OFF, automatic measurement of downlink RSRP in
NCELL DL neighboring cells is disabled. This parameter applies
DLRSR CoMP only to LTE FDD and LTE TDD.
PMEAS GUI Value Range: OFF(Off), ON(On)
PARA Unit: None
Actual Value Range: OFF, ON
Default Value: OFF(Off)
NCellDl NCellDl MOD LOFD-0 Coordin Meaning: Indicates the offset for reporting the event
RsrpMe RsrpMe NCELL 70208 ated of automatic measurement of downlink RSRP in
asPara asA3Off DLRSR LAOFD Scheduli neighboring cells. This offset is the difference
set PMEAS -120201 ng based between the signal quality of a neighboring cell and
PARA Power that of the serving cell. A larger value indicates that a
LEOFD- Control neighboring cell must have better quality to report the
LST 111306/
NCELL DL event. This parameter applies only to LTE FDD and
TDLOF LTE TDD.
DLRSR D-12020 CoMP
PMEAS 5 Breathin GUI Value Range: -30~30
PARA g Pilot Unit: 0.5dB
LEOFD-
111307 eMIMO Actual Value Range: -15~15
Default Value: -12
CellDlC DpsServ MOD LAOFD DL Meaning: Indicates the threshold of the downlink PRB
ompAlg ingCell CELLD -120201 CoMP usage for a DPS serving cell when DL CoMP is
o DlPrbTh LCOMP enabled. When the PRB usage of a candidate cell
d ALGO exceeds this threshold, the cell can be selected as a
LST DPS serving cell. This parameter applies only to LTE
CELLD FDD cells.
LCOMP GUI Value Range: 0~100
ALGO Unit: %
Actual Value Range: 0~100
Default Value: 40
CellDlC Homnet MOD LAOFD DL Meaning: Indicates the RSRP offset threshold for DPS
ompAlg DpsCoC CELLD -120201 CoMP UEs in selecting a coordinating cell in a HomNet. A
o ellRsrpT LCOMP large value of this parameter indicates a high
hd ALGO requirement on neighboring cell quality for reporting
LST measurement events and a small number of DPS UEs
CELLD selecting a coordinating cell in a HomNet. A small
LCOMP value of this parameter indicates a large number of
ALGO DPS UEs selecting a coordinating cell in a HomNet.
This parameter applies only to LTE FDD cells.
GUI Value Range: -30~30
Unit: 0.5dB
Actual Value Range: -15~15
Default Value: -6
CellDlC HetnetD MOD LAOFD DL Meaning: Indicates the RSRP offset threshold for DPS
ompAlg psCoCel CELLD -120201 CoMP UEs in selecting a coordinating cell in a HetNet. A
o lRsrpTh LCOMP large value of this parameter indicates a high
d ALGO requirement on neighboring cell quality for reporting
LST measurement events and a small number of DPS UEs
CELLD selecting a coordinating cell in a HetNet. A small
LCOMP value of this parameter indicates a large number of
ALGO DPS UEs selecting a coordinating cell in a HetNet.
This parameter applies only to LTE FDD cells.
GUI Value Range: -30~30
Unit: 0.5dB
Actual Value Range: -15~15
Default Value: -12
CellDlC DpsLoa MOD LAOFD DL Meaning: Indicates the threshold of the difference
ompAlg dDiffTh CELLD -120201 CoMP between the PRB usage of a DPS serving cell and that
o d LCOMP of a DPS coordinating cell when DL CoMP is
ALGO enabled. When the difference between the PRB usage
LST of the serving cell and the coordinating cell exceeds
CELLD this threshold, the coordinating cell can function as the
LCOMP target cell of DPS UEs. This parameter applies only to
ALGO LTE FDD cells.
GUI Value Range: 0~50
Unit: %
Actual Value Range: 0~50
Default Value: 20
CellDlC DpsCoC MOD LAOFD DL Meaning: Indicates the threshold for the ratio of the
ompAlg ellUserR CELLD -120201 CoMP number of uplink synchronized UEs in a dynamic
o atioThd LCOMP point selection (DPS) serving cell to a DPS
ALGO coordinating cell when DL CoMP is enabled. When
LST the ratio of the number of uplink synchronized UEs in
CELLD the coordinating cell (including those transferred to
LCOMP the coordinating cell) to that in the serving cell is
ALGO smaller than this threshold, the coordinating cell can
function as the target cell of DPS UEs. This parameter
applies only to LTE FDD cells.
GUI Value Range: 0~100
Unit: %
Actual Value Range: 0~100
Default Value: 50
CellDlC JtServin MOD LAOFD DL Meaning: Indicates the threshold of the downlink PRB
ompAlg gCellDl CELLD -120201 CoMP usage for a serving cell for joint transmission when
o PrbThd LCOMP DL CoMP is enabled. When the PRB usage of a
ALGO candidate cell is smaller than this threshold, the cell
LST can be selected as a serving cell for joint transmission.
CELLD This parameter applies only to LTE FDD cells.
LCOMP GUI Value Range: 0~100
ALGO Unit: %
Actual Value Range: 0~100
Default Value: 20
CellDlC JtCoCell MOD LAOFD DL Meaning: Indicates the RSRP offset threshold for joint
ompAlg RsrpThd CELLD -120201 CoMP transmission UEs in selecting a coordinating cell. A
o LCOMP large value of this parameter indicates a high
ALGO requirement on neighboring cell quality for reporting
LST measurement events and a small number of joint
CELLD transmission UEs. A small value of this parameter
LCOMP indicates a large number of joint transmission UEs.
ALGO This parameter applies only to LTE FDD cells.
GUI Value Range: -30~30
Unit: 0.5dB
Actual Value Range: -15~15
Default Value: -6
CellDlC JtCoCell MOD LAOFD DL Meaning: Indicates the threshold of the downlink PRB
ompAlg DlPrbTh CELLD -120201 CoMP usage for joint transmission UEs in selecting a
o d LCOMP coordinating cell when DL CoMP is enabled. When
ALGO the PRB usage of a candidate cell is lower than this
LST threshold, the cell can be selected as a coordinating
CELLD cell for joint transmission. This parameter applies only
LCOMP to LTE FDD cells.
ALGO GUI Value Range: 0~100
Unit: %
Actual Value Range: 0~100
Default Value: 20
Unit: None
Actual Value Range: SpsSchSwitch,
SinrAdjustSwitch, PreAllocationSwitch,
UlVmimoSwitch, TtiBundlingSwitch,
SmartPreAllocationSwitch, PuschDtxSwitch,
UlIblerAdjustSwitch, UlEnhancedFssSwitch,
UlEnhancedSrSchSwitch, SchedulerCtrlPowerSwitch,
UlIicsAlgoSwitch, UlMinGbrSwitch,
UlMbrCtrlSwitch, MbrUlSchSwitch,
UeAmbrUlSchSwitch, UlEnhancedDopplerSwitch,
UlRaUserSchOptSw, UlLast2RetransSchOptSwitch,
UlInterfFssSwitch, UlSmallRBSpectralEffOptSw,
PuschUsePucchRbSwitch, PuschDtxSchOptSwitch,
ULFSSAlgoSwitch, PrachRbReuseSwitch,
SrSchDataAdptSw, UlFssUserThdStSwitch,
HighOrderVMIMOSwitch, VMIMOReduceMCSRi-
seRBSwitch, VoLTEUeVmimoSwitch,
TtiBundlingForVideoSwitch
Default Value: SpsSchSwitch:Off,
SinrAdjustSwitch:On, PreAllocationSwitch:On,
UlVmimoSwitch:Off, TtiBundlingSwitch:Off,
SmartPreAllocationSwitch:On, PuschDtxSwitch:On,
UlIblerAdjustSwitch:Off, UlEnhancedFssSwitch:On,
UlEnhancedSrSchSwitch:On, SchedulerCtrlPowerS-
witch:Off, UlIicsAlgoSwitch:Off,
UlMinGbrSwitch:Off, UlMbrCtrlSwitch:Off,
MbrUlSchSwitch:Off, UeAmbrUlSchSwitch:Off,
UlEnhancedDopplerSwitch:On,
UlRaUserSchOptSw:Off,
UlLast2RetransSchOptSwitch:On,
UlInterfFssSwitch:Off, UlSmallRBSpectralEf-
fOptSw:Off, PuschUsePucchRbSwitch:Off,
PuschDtxSchOptSwitch:Off, ULFSSAlgoSwitch:On,
PrachRbReuseSwitch:Off, SrSchDataAdptSw:On,
UlFssUserThdStSwitch:Off, HighOrderVMIMOS-
witch:Off, VMIMOReduceMCSRiseRBSwitch:Off,
VoLTEUeVmimoSwitch:Off, TtiBundlingForVideoS-
witch:Off
EpfEnhancedSwitch(EpfEnhancedSwitch),
AperiodicCqiTrigOptSwitch(AperiodicCqiTrigOptS-
witch), VoipTbsBasedMcsSelS-
witch(VoipTbsBasedMcsSelSwitch),
PagingInterfRandSwitch(PagingInterfRandSwitch),
DlSingleUsrMcsOptSwitch(DlSingleUsrMcsOptS-
witch), SubframeSchDiffSwitch(SubframeSchDiffS-
witch), TailPackagePriSchS-
witch(TailPackagePriSchSwitch),
UeSigMcsEnhanceSwitch(UeSigMcsEnhanceSwitch),
FreqSelJudgeIgnorDopplerSwitch(FreqSelJudgeIgnor-
DopplerSwitch),
SIB1InterfRandSwitch(SIB1InterfRandSwitch),
EnhExtQCISpsSchSwitch(EnhExtQCISpsSchSwitch),
DlVoipBundlingSwitch(DlVoipBundlingSwitch),
DlPacketLenAwareSchSw(DlPacketLenAwar-
eSchSw), RLCArqFeedbackEnhanced-
Switch(RLCArqFeedbackEnhancedSwitch),
PaReconfigOptSwitch(PaReconfigOptSwitch),
RankRapidRptSwitch(RankRapidRptSwitch),
DlRLCStateReportSchDe-
laySw(DlRLCStateReportSchDelaySw),
SmallPktMcsSelectAlgoSw(SmallPktMcsSelectAl-
goSw), SRB0SplitSchSw(SRB0SplitSchSw),
BfUserPairPriorSwitch(BfUserPairPriorSwitch),
HarqAllocOptSwitch(HarqAllocOptSwitch),
Pusch32Switch(Pusch32Switch),
DlPreciseAmbrCtrlSwitch(DlPreciseAmbrCtrlSwitch)
Unit: None
Actual Value Range: FreqSelSwitch, SpsSchSwitch,
MBSFNShutDownSwitch, NonGbrBundlingSwitch,
EnAperiodicCqiRptSwitch, DlMbrCtrlSwitch,
MbrDlSchSwitch, UeAmbrDlSchSwitch,
EpfEnhancedSwitch, AperiodicCqiTrigOptSwitch,
VoipTbsBasedMcsSelSwitch, PagingInterfRand-
Switch, DlSingleUsrMcsOptSwitch,
SubframeSchDiffSwitch, TailPackagePriSchSwitch,
UeSigMcsEnhanceSwitch, FreqSelJudgeIgnorDop-
plerSwitch, SIB1InterfRandSwitch,
EnhExtQCISpsSchSwitch, DlVoipBundlingSwitch,
DlPacketLenAwareSchSw, RLCArqFeedbackEnhan-
cedSwitch, PaReconfigOptSwitch,
RankRapidRptSwitch, DlRLCStateReportSchDe-
laySw, SmallPktMcsSelectAlgoSw, SRB0SplitSchSw,
BfUserPairPriorSwitch, HarqAllocOptSwitch,
Pusch32Switch, DlPreciseAmbrCtrlSwitch
Default Value: FreqSelSwitch:Off, SpsSchSwitch:Off,
MBSFNShutDownSwitch:Off, NonGbrBundlingS-
witch), UnnecHoOptWithou-
tRIM(UnnecHoOptWithoutRIM)
Unit: None
Actual Value Range: IntraFreqMroSwitch,
InterFreqMroSwitch, UtranMroSwitch,
GeranMroSwitch, UEMroSwitch,
IntraFreqReselOptSwitch, UtranUnnecHoOptSwitch,
GeranUnnecHoOptSwitch, IntraRatCallbackSwitch,
UnnecHoOptWithoutRIM
Default Value: IntraFreqMroSwitch:Off,
InterFreqMroSwitch:Off, UtranMroSwitch:Off,
GeranMroSwitch:Off, UEMroSwitch:Off,
IntraFreqReselOptSwitch:Off, UtranUnnecHoOptS-
witch:Off, GeranUnnecHoOptSwitch:Off,
IntraRatCallbackSwitch:Off, UnnecHoOptWithou-
tRIM:Off
CellDrx DrxAlg MOD LBFD-0 DRX Meaning: Indicates whether to enable DRX. This
Para Switch CELLD 02017/ Breathin parameter does not control dynamic DRX. In FDD
RXPAR TDLBF g Pilot and TDD cells, DRX takes effect on a CA UE only
A D-00201 when this parameter is set to ON for eNodeBs serving
LST 7/ both the PCell and SCells of the CA UE. In NB-IoT
CELLD MLBFD cells, DRX takes effect when this parameter is set to
RXPAR -120002 ON.
A 36 GUI Value Range: OFF(Off), ON(On)
LEOFD- Unit: None
111306/
TDLOF Actual Value Range: OFF, ON
D-12020 Default Value: OFF(Off)
5
CellPdc Epdcch MOD LBFD-0 Physical Meaning: Indicates whether to enable algorithms
chAlgo AlgoSwi CELLP 02003/ Channel related to the EPDCCH. EpdcchFunctionSwitch:
tch DCCHA TDLBF Manage Indicates whether to support EPDCCH. If this option
LGO D-00200 ment is selected, EPDCCH is supported. This option applies
LST 3 only to LTE FDD and LTE TDD.
CELLP GUI Value Range: EpdcchFunctionS-
DCCHA witch(EpdcchFunctionSwitch)
LGO Unit: None
Actual Value Range: EpdcchFunctionSwitch
Default Value: EpdcchFunctionSwitch:Off
CellCsp CellCsp MOD LOFD-0 Coordin Meaning: Indicates whether to enable CSPC in the
cPara cSwitch CELLC 70208 ated cell. This parameter applies only to LTE FDD and
SPCPA TDLOF Scheduli LTE TDD.
RA D-08020 ng based GUI Value Range: OFF(Off), ON(On)
LST 3 Power
Control Unit: None
CELLC
SPCPA Coordin Actual Value Range: OFF, ON
RA ated Default Value: OFF(Off)
Scheduli
ng based
Power
Control
CellCsp CelleCs MOD LOFD-0 Coordin Meaning: Indicates whether to enable cell-level
cPara pcSwitc CELLC 70208 ated enhanced CSPC (eCSPC). eCSPC is enabled only
h SPCPA Scheduli when this parameter is set to ON(On). This parameter
RA ng based applies only to LTE FDD.
LST Power GUI Value Range: OFF(Off), ON(On)
CELLC Control
Unit: None
SPCPA
RA Actual Value Range: OFF, ON
Default Value: OFF(Off)
CellCsp IntraEnb MOD LOFD-0 Coordin Meaning: Indicates whether to enable intra-eNodeB
cPara CspcSw CELLC 70208 ated CSPC. Intra-eNodeB CSPC is enabled only when this
SPCPA Scheduli parameter is set to ON(On). This parameter applies
RA ng based only to LTE FDD.
LST Power GUI Value Range: OFF(Off), ON(On)
CELLC Control
Unit: None
SPCPA
RA Actual Value Range: OFF, ON
Default Value: OFF(Off)
CellAlg SfnUlSc MOD LOFD-0 SFN Meaning: Indicates the SFN uplink scheduling mode.
oSwitch hSwitch CELLA 03029/ Adaptiv The uplink scheduling modes include the joint
LGOSW TDLOF e SFN/ scheduling mode, and the auto-selection mode
ITCH D-00107 SDMA between joint scheduling and independent scheduling.
LST 5/ This parameter applies only to LTE FDD and LTE
CELLA MLOFD TDD.
LGOSW -121204 GUI Value Range: ADAPTIVE(Adaptive scheduling),
ITCH LOFD-0 JOINT(Joint scheduling)
70205/ Unit: None
TDLOF
D-00200 Actual Value Range: ADAPTIVE, JOINT
8 Default Value: JOINT(Joint scheduling)
CellAlg SfnDlSc MOD LOFD-0 SFN Meaning: Indicates the SFN downlink scheduling
oSwitch hSwitch CELLA 03029/ Adaptiv mode. The downlink scheduling modes include the
LGOSW TDLOF e SFN/ joint scheduling mode, and the auto-selection mode
ITCH D-00107 SDMA between joint scheduling and independent scheduling.
LST 5/ This parameter applies only to LTE FDD and LTE
MLOFD Inter- TDD.
CELLA eNodeB
LGOSW -121204 GUI Value Range: ADAPTIVE(Adaptive scheduling),
SFN
ITCH LOFD-0 Based JOINT(Joint scheduling)
70205/ on Unit: None
TDLOF Coordin
D-00200 Actual Value Range: ADAPTIVE, JOINT
ated
8 eNodeB Default Value: JOINT(Joint scheduling)
TDLOF Inter-
D-00108 eNodeB
0 Adaptiv
TDLOF e SFN/
D-00108 SDMA
2 Based
on
Coordin
ated
eNodeB
IDLE_EDRX_SWITCH(IDLE_EDRX_SWITCH),
G_VALUE_CFG_SWITCH(G_VALUE_CFG_SWIT
CH),
SI_UPDATE_REL_UE_SWITCH(SI_UPDATE_REL
_UE_SWITCH),
EMTC_ONLY_CELL_SWITCH(EMTC_ONLY_CE
LL_SWITCH),
MODE_A_UE_TA_SCHEDULING_SWITCH(MOD
E_A_UE_TA_SCHEDULING_SWITCH),
EMTC_UE_ACK_START_OFFSET_CFG(EMTC_U
E_ACK_START_OFFSET_CFG),
DL_PERFORMANCE_ENHANCE_SWITCH(DL_P
ERFORMANCE_ENHANCE_SWITCH),
UL_PERFORMANCE_ENHANCE_SWITCH(UL_P
ERFORMANCE_ENHANCE_SWITCH),
MPDCCH_MORE_AVAIL_NB_SWITCH(MPDCCH
_MORE_AVAIL_NB_SWITCH),
UL_MCS_SCHEDULING_OPT_SWITCH(UL_MCS
_SCHEDULING_OPT_SWITCH)
Unit: None
Actual Value Range: EMTC_SWITCH,
IDLE_EDRX_SWITCH, G_VALUE_CFG_SWITCH,
SI_UPDATE_REL_UE_SWITCH,
EMTC_ONLY_CELL_SWITCH,
MODE_A_UE_TA_SCHEDULING_SWITCH,
EMTC_UE_ACK_START_OFFSET_CFG,
DL_PERFORMANCE_ENHANCE_SWITCH,
UL_PERFORMANCE_ENHANCE_SWITCH,
MPDCCH_MORE_AVAIL_NB_SWITCH,
UL_MCS_SCHEDULING_OPT_SWITCH
Default Value: EMTC_SWITCH:Off,
IDLE_EDRX_SWITCH:Off,
G_VALUE_CFG_SWITCH:Off,
SI_UPDATE_REL_UE_SWITCH:Off,
EMTC_ONLY_CELL_SWITCH:Off,
MODE_A_UE_TA_SCHEDULING_SWITCH:On,
EMTC_UE_ACK_START_OFFSET_CFG:Off,
DL_PERFORMANCE_ENHANCE_SWITCH:Off,
UL_PERFORMANCE_ENHANCE_SWITCH:Off,
MPDCCH_MORE_AVAIL_NB_SWITCH:Off,
UL_MCS_SCHEDULING_OPT_SWITCH:Off
based on NackDtxIdentifySwitch(NackDtxIdentifySwitch):
EPC(LT indicates whether the eNodeB regards NACK/DTX
E TDD) confusions as DTXs or NACKs during PUSCH
demodulation. When this option is selected, the
eNodeB regards NACK/DTX confusions as DTXs.
When this option is deselected, the eNodeB regards
NACK/DTX confusions as NACKs. This option
applies only to LTE FDD and LTE TDD.
CaDl2CCExtSwitch(CaDl2CCExtSwitch): indicates
whether to enable downlink 2CC CA on extended
bandwidth. Downlink FDD 2CC CA can reach an
aggregated bandwidth between 20 MHz and 40 MHz
(inclusive) and downlink TDD 2CC CA can reach an
aggregated bandwidth between 30 MHz and 40 MHz
(inclusive) only if this option is selected. To use this
CA feature, operators must select this option
regardless of whether the local cell acts as a PCell or
an SCell for a UE. This option takes effect only in
adaptive (frequency-based) configuration mode. This
option applies only to LTE FDD and LTE TDD.
CaDl3CCExtSwitch(CaDl3CCExtSwitch): indicates
whether to enable downlink 3CC CA on extended
bandwidth. Downlink FDD 3CC CA can reach an
aggregated bandwidth between 40 MHz and 60 MHz
(inclusive) only if this option is selected. To use this
CA feature, operators must select this option
regardless of whether the local cell acts as a PCell or
an SCell for a UE. This option takes effect only in
adaptive (frequency-based) configuration mode. This
option applies only to LTE FDD.
VolteSupportCaInterFreqMeasSw(VolteSupportCaIn-
terFreqMeasSw): indicates whether VoLTE UEs can
perform inter-frequency measurements for SCell
configuration or PCC anchoring for connected-mode
UEs. The eNodeB delivers inter-frequency
measurement configurations to CA UEs running
VoLTE services for SCell configuration or PCC
anchoring only if this option is selected. To enable the
eNodeB to configure NR SCGs based on gap-assisted
inter-frequency measurements for UEs with
concurrent VoLTE and data services, select this
option. This option applies only to LTE FDD and LTE
TDD.
CaEnhAperiodicCqiRptSwitch: indicates the aperiodic
CQI reporting mechanism in CA. If this option is
selected, then:
Dc3cSwitch(Dc3cSwitch), MultiCarrierFlexCaS-
witch(MultiCarrierFlexCaSwitch), NackDtxIdentify-
Switch(NackDtxIdentifySwitch),
CaDl2CCExtSwitch(CaDl2CCExtSwitch),
CaDl3CCExtSwitch(CaDl3CCExtSwitch),
VolteSupportCaInterFreqMeasSw(VolteSupportCaIn-
terFreqMeasSw), CaEnhAperiodicCqiRptS-
witch(CaEnhAperiodicCqiRptSwitch),
SpectrumCoordinationSwitch(SpectrumCoordina-
tionSwitch), VolteUlCaControlS-
witch(VolteUlCaControlSwitch)
Unit: None
Actual Value Range: CaDl3CCSwitch,
CaUl2CCSwitch, CaDl4CCSwitch,
InterFddTddCaSwitch, 2CCDlCaEnhanceSwitch,
CaDl5CCSwitch, CaInstantlyJudgeSwitch,
LaaCaDlSwitch, FddTddCaUlServiceFirstSwitch,
RcvA2CfgSccSwitch, Dc3cSwitch, MultiCarrierFlex-
CaSwitch, NackDtxIdentifySwitch,
CaDl2CCExtSwitch, CaDl3CCExtSwitch,
VolteSupportCaInterFreqMeasSw, CaEnhAperiodicC-
qiRptSwitch, SpectrumCoordinationSwitch,
VolteUlCaControlSwitch
Default Value: CaDl3CCSwitch:Off,
CaUl2CCSwitch:Off, CaDl4CCSwitch:Off,
InterFddTddCaSwitch:Off,
2CCDlCaEnhanceSwitch:Off, CaDl5CCSwitch:Off,
CaInstantlyJudgeSwitch:Off, LaaCaDlSwitch:Off,
FddTddCaUlServiceFirstSwitch:Off,
RcvA2CfgSccSwitch:Off, Dc3cSwitch:Off,
MultiCarrierFlexCaSwitch:Off, NackDtxIdentify-
Switch:Off, CaDl2CCExtSwitch:Off,
CaDl3CCExtSwitch:Off, VolteSupportCaInterFreq-
MeasSw:Off, CaEnhAperiodicCqiRptSwitch:Off,
SpectrumCoordinationSwitch:Off,
VolteUlCaControlSwitch:Off
EmimoFbaSwitch:Off, New4TCodebookSwitch:Off,
4TxTM9MuMimoSwitch:Off, DrxSimulAckNack-
AndCqiSwitch:Off, PreciseAmcSwitch:Off,
EmimoCsiEnhanceSwitch:Off, PUSCH12Switch:Off
Cell HighSpe ADD LOFD-0 High Meaning: Indicates the speed flag of the cell. Set this
edFlag CELL 01007/ Speed parameter to HIGH_SPEED if the cell is used to
MOD TDLOF Mobility provide coverage for a high-speed railway. Set this
CELL D-00100 Ultra parameter to LOW_SPEED in other scenarios. TDD
7 High cells with a bandwidth of 5 MHz or in 8T8R mode can
LST only be configured as low-speed cells. TDD cells
CELL LOFD-0 Speed
01008 Mobility cannot be configured as ultra-high-speed cells. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: LOW_SPEED(Low speed cell
flag), HIGH_SPEED(High speed cell flag),
ULTRA_HIGH_SPEED(Ultra high speed cell flag),
EXTRA_HIGH_SPEED(Extra high speed cell flag)
Unit: None
Actual Value Range: LOW_SPEED, HIGH_SPEED,
ULTRA_HIGH_SPEED, EXTRA_HIGH_SPEED
Default Value: LOW_SPEED(Low speed cell flag)
Cell CellRadi ADD LBFD-0 Random Meaning: Indicates the radius of the cell, that is, the
us CELL 02010/ Access farthest distance that a cell can cover under the
MOD TDLBF Extende condition of keeping certain network performance. If
CELL D-00201 d Cell this parameter is set to a value greater than 100 km,
0 Access the Extended Cell Access Radius Beyond 100km
LST feature takes effect. Only FDD cells can be configured
CELL LOFD-0 Radius
81223 Beyond with a radius more than 100 km. This parameter
100km applies only to LTE FDD and LTE TDD.
LOFD-0
01009/ Extende GUI Value Range: 1~200000
TDLOF d Cell Unit: m
D-00100 Access Actual Value Range: 1~200000
9 Radius
Default Value: 10000
LBFD-0 Cell
02012 Access
LOFD-0 Radius
02015/ up to
TDLOF 15km
D-00201 RACH
5 Optimiz
ation
Cell UlCycli ADD LBFD-0 Normal Meaning: Indicates the UL cyclic prefix length of a
cPrefix CELL 0100401 CP cell. A cyclic prefix can be a common or extended
MOD / Extende cyclic prefix. An extended cyclic prefix is generally
CELL TDLBF d CP used in a complex environment with a strong multi-
D-00100 path effect and long delay. In a cell, the UL cyclic
LST 401 Broadca prefix length can be different from the DL one. In
CELL st of addition, the UL or DL cyclic prefix length of a cell
LOFD-0 system
01031/ must be the same as that of the cell using the same
informat BBP. For details, see 3GPP TS 36.211.
TDLOF ion
D-00103 GUI Value Range: NORMAL_CP(Normal),
1 EXTENDED_CP(Extended)
LBFD-0 Unit: None
02009/ Actual Value Range: NORMAL_CP,
TDLBF EXTENDED_CP
D-00200
9/ Default Value: NORMAL_CP(Normal)
MLBFD
-120002
29
Cell DlCycli ADD LBFD-0 Normal Meaning: Indicates the length of the DL cyclic prefix
cPrefix CELL 0100401 CP of a cell. A DL cyclic prefix can be a common or
MOD / Extende extended cyclic prefix. An extended cyclic prefix is
CELL TDLBF d CP generally used in a complex environment with a
D-00100 strong multi-path effect and long delay. In a cell, the
LST 401 eMTC UL cyclic prefix length can be different from the DL
CELL Introduc one. In addition, the UL or DL cyclic prefix length of
LOFD-0 tion
01031/ a cell must be the same as that of the cell using the
TDLOF same BBP. For details, see 3GPP TS 36.211.
D-00103 GUI Value Range: NORMAL_CP(Normal),
1 EXTENDED_CP(Extended)
TDLEO Unit: None
FD-121 Actual Value Range: NORMAL_CP,
611 EXTENDED_CP
Default Value: NORMAL_CP(Normal)
CellAlg EicicSw MOD LAOFD Dynami Meaning: Indicates whether to disable the TDM-based
oSwitch itch CELLA -081233 c TDM eICIC algorithm or apply the static or dynamic mode
LGOSW eICIC to the eICIC algorithm. In a heterogeneous network
ITCH (HetNet), the eICIC function is used together with the
LST cell range expansion (CRE) function of the micro base
CELLA station to expand the coverage and increase the
LGOSW number of users absorbed by the micro cell. To
ITCH implement the eICIC function, ensure that the value of
this parameter must be set consistently for macro and
micro cells. Static mode applies only to TDD, and
dynamic mode applies only to FDD. This parameter
applies only to LTE FDD and LTE TDD.
GUI Value Range: OFF(Off), STATIC(Static),
DYNAMIC(Dynamic)
Unit: None
Actual Value Range: OFF, STATIC, DYNAMIC
Default Value: OFF(Off)
CellAlg FeicicS MOD LAOFD FeICIC Meaning: Indicates whether to enable the FeICIC
oSwitch witch CELLA -081234 algorithm. In a heterogeneous network (HetNet), this
LGOSW algorithm can be used together the Dynamic TDM
ITCH eICIC algorithm and the CRE function to extend the
LST micro cell coverage area and increase the number of
CELLA UEs served by the micro cell. To support the FeICIC
LGOSW algorithm, set the EicicSwitch parameter to
ITCH DYNAMIC in both the macro and micro cells. This
parameter applies only to LTE FDD.
GUI Value Range: OFF(Off), ABS(ABS)
Unit: None
Actual Value Range: OFF, ABS
Default Value: OFF(Off)
Cell EuCellS ADD LBFD-0 Broadca Meaning: Indicates the active or standby mode of the
tandby CELL 02009/ st of cell. A cell is in active mode by default. If this
Mode MOD TDLBF system parameter is set to STANDBY, an inter-BBU SFN
CELL D-00200 informat auxiliary cell can switch back to the standby mode to
9 ion provide services if inter-BBU faults occur. Only
LST common cells, SFN cells or MPRU_AGGREGATION
CELL cells support the standby mode.
GUI Value Range: ACTIVE(Active),
STANDBY(Standby)
Unit: None
Actual Value Range: ACTIVE, STANDBY
Default Value: ACTIVE(Active)
CellAlg EnhMI MOD LOFD-0 DL 2x2 Meaning: Indicates the switch used to enable or
oSwitch MOSwit CELLA 01001 MIMO disable enhanced MIMO. Admitted UEs are allowed
ch LGOSW LOFD-0 DL 4x2 to enter TM9 or TM10 mode only if the TM9Switch
ITCH 01003 MIMO or TM10Switch option is selected. The
LST TM4TM9AdaptiveSwitch option can be selected only
LOFD-0 DL 4x4 after the TM9Switch option is selected. If the
CELLA 01060 MIMO
LGOSW TM4TM9AdaptiveSwitch option is selected, UEs
ITCH TDLAO DL 2- meeting certain conditions are allowed to adaptively
FD-001 Layer enter TM4 and TM9 mode. Otherwise, UEs are
00114 MIMO prohibited from adaptively entering TM4 and TM9
TDLAO Based mode. Enhanced MIMO does not apply to the LBBPc.
FD-081 on TM9 The TM4TM9AdaptiveSwitch and TM10Switch
409 DL 4- options apply only to LTE FDD. This parameter
Layer applies only to LTE FDD. ChannelRecSwitch:
LAOFD Indicates whether to enable channel reconstruction
-111204 MIMO
Based optimization. Channel reconstruction optimization is
LEOFD- on TM9 enabled only if this option is selected. This option
111307 applies only to LTE FDD. TM9HybridPrecodingS-
Adaptiv witch: Indicates whether to enable the TM9 hybrid
e SFN/ precoding algorithm in massive MIMO scenarios. If
SDMA this option is selected, the TM9 hybrid precoding
with function is enabled to improve the beamforming
TM10 capability of closed-loop TM9 UEs. If this option is
eMIMO deselected, the TM9 hybrid precoding function is
disabled, and the beamforming capability of closed-
loop TM9 UEs remains unchanged. This option
applies only to LTE TDD.
GUI Value Range: TM9Switch(TM9Switch),
TM4TM9AdaptiveSwitch(TM4TM9AdaptiveSwitch),
TM10Switch(TM10Switch),
ChannelRecSwitch(ChannelRecSwitch),
TM9HybridPrecodingSwitch(TM9HybridPrecodingS-
witch)
Unit: None
Actual Value Range: TM9Switch,
TM4TM9AdaptiveSwitch, TM10Switch,
ChannelRecSwitch, TM9HybridPrecodingSwitch
Default Value: TM9Switch:Off,
TM4TM9AdaptiveSwitch:Off, TM10Switch:Off,
ChannelRecSwitch:Off, TM9HybridPrecodingS-
witch:Off
Cell CrsPort ADD LOFD-0 DL 2x2 Meaning: Indicates the number of ports for
Num CELL 01001/ MIMO transmitting cell-specific reference signal (CRS). As
MOD TDLOF DL 4x2 defined in 3GPP specifications, this parameter can be
CELL D-00100 MIMO set to CRS_PORT_1, CRS_PORT_2, or
1 CRS_PORT_4. The value CRS_PORT_1 indicates
LST DL 4x4 that one CRS port (port 0) is configured. The value
CELL LOFD-0 MIMO
01003 CRS_PORT_2 indicates that two CRS ports (ports 0
DL 4x4 and 1) are configured. The value CRS_PORT_4
LOFD-0 MIMO indicates that four CRS ports (ports 0, 1, 2, and 3) are
01060 configured.
DL
TDLOF Flexible GUI Value Range: CRS_PORT_1(1 port),
D-00106 3D- CRS_PORT_2(2 ports), CRS_PORT_4(4 ports)
0 Beamfor Unit: None
TDLEO ming
FD-121 Actual Value Range: CRS_PORT_1, CRS_PORT_2,
615 CRS_PORT_4
Default Value: CRS_PORT_2(2 ports)
InSessionUeQtyUlDlAccSwitch(InSessionUeQtyUl-
DlAccSwitch), RrcConnectedUserCountOptS-
witch(RrcConnectedUserCountOptSwitch)
Unit: None
Actual Value Range: BasedA3EdgeUserSwitch,
UlStatOptmizeSwitch, InSessionUeQtyUlDlAccS-
witch, RrcConnectedUserCountOptSwitch
Default Value: BasedA3EdgeUserSwitch:Off,
UlStatOptmizeSwitch:Off, InSessionUeQtyUl-
DlAccSwitch:Off, RrcConnectedUserCountOptS-
witch:Off
CellCou EdgeUs MOD LEOFD- Virtual Meaning: Indicates the offset for cell edge user (CEU)
nterPara erA3Off CELLC 111305 4T4R identification event A3. This offset is the difference
Group set OUNTE LOFD-0 Adaptiv between the signal quality of a neighboring cell and
RPARA 60201 e Inter- that of the serving cell. A larger value of this
GROUP Cell parameter results that better signal quality of the
LOFD-0 neighboring cell is required for the reporting of CEU
LST 70208 Interfere
CELLC nce identification event A3 and the eNodeB has a lower
OUNTE Coordin probability of identifying a UE as a CEU. A smaller
RPARA ation value of this parameter results in a higher probability
GROUP that a UE is identified as a CEU. This parameter
Coordin applies only to LTE FDD and LTE TDD.
ated
Scheduli GUI Value Range: -30~30
ng based Unit: 0.5dB
Power Actual Value Range: -15~15
Control
Default Value: -13
CellCou EdgeUs MOD None None Meaning: Indicates the serving cell RSRP threshold
nterPara erServR CELLC for determining CEUs when the
Group SRPThd OUNTE BasedA3EdgeUserSwitch option of the
RPARA CellCounterAlgoSwitch parameter is selected. A
GROUP larger value of this parameter indicates a higher
LST probability of identifying a UE as a CEU. A smaller
CELLC value of this parameter indicates a lower probability
OUNTE of identifying a UE as a CEU. The value 255 indicates
RPARA that the serving cell RSRP is not used in the
GROUP identification. This parameter applies only to LTE
FDD and LTE TDD.
GUI Value Range: -140~-43,255
Unit: dBm
Actual Value Range: -140~-43,255
Default Value: 255
CellCsi CsiRsS MOD TDLAO DL 2- Meaning: Indicates whether to configure CSI-RSs for
RsParaC witch CELLC FD-001 Layer UEs. If this parameter is set to NOT_CFG(Not
fg SIRSPA 00114 MIMO configure), the eNodeB does not configure CSI-RSs
RACFG TDLAO Based for UEs. If this parameter is set to FIXED_CFG(Fixed
LST FD-081 on TM9 configure), the eNodeB configures CSI-RSs for UEs
CELLC 409 DL 4- that support CSI-RSs. If this parameter is set to
SIRSPA Layer ADAPTIVE_CFG(ADAPTIVE_CFG), the eNodeB
RACFG MIMO determines whether to configure CSI-RSs for UEs that
Based support CSI-RSs based on the proportion of TM9
on TM9 UEs. When SfnLoadBasedAdptSwitch is deselected in
a TDD cell with adaptive SFN enabled, neither
FIXED_CFG nor ADAPTIVE_CFG takes effect. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: NOT_CFG(Not configure),
FIXED_CFG(Fixed configure),
ADAPTIVE_CFG(ADAPTIVE_CFG)
Unit: None
Actual Value Range: NOT_CFG, FIXED_CFG,
ADAPTIVE_CFG
Default Value: NOT_CFG(Not configure)
CellCsi CsiRsPe MOD TDLAO DL 2- Meaning: Indicates the channel state information
RsParaC riod CELLC FD-001 Layer (CSI) reference signal (RS) measurement period. This
fg SIRSPA 00114 MIMO parameter applies only to LTE FDD and LTE TDD.
RACFG TDLAO Based GUI Value Range: ms5(ms5), ms10(ms10),
LST FD-081 on TM9 ms20(ms20), ms40(ms40), ms80(ms80)
CELLC 409 DL 4- Unit: None
SIRSPA Layer
RACFG MIMO Actual Value Range: ms5, ms10, ms20, ms40, ms80
Based Default Value: ms5(ms5)
on TM9
CellCsi CsiRsCo MOD LOFD-0 DL 2x2 Meaning: Indicates the threshold of the proportion of
RsParaC nfigUser CELLC 01001/ MIMO RRC_CONNECTED UEs supporting CSI_RS that is
fg RatioTh SIRSPA TDLOF DL 4x2 used to determine a change from the CSI-RS
RACFG D-00100 MIMO unconfigured state to the CSI-RS configured state
LST 1 when adaptive CSI-RS configuration is adopted. This
DL 4x4 parameter applies only to LTE FDD and LTE TDD.
CELLC LOFD-0 MIMO
SIRSPA 01003 GUI Value Range: 0~100
RACFG DL 2-
LOFD-0 Layer Unit: %
01060/ MIMO Actual Value Range: 0~100
TDLOF Based
D-00106 Default Value: 50
on TM9
0
DL 4-
TDLAO Layer
FD-001 MIMO
00114 Based
TDLAO on TM9
FD-081
409
CellCsi CsiRsU MOD LOFD-0 DL 2x2 Meaning: Indicates the threshold of the proportion of
RsParaC nconfig CELLC 01001/ MIMO RRC_CONNECTED UEs supporting CSI_RS that is
fg UserRati SIRSPA TDLOF DL 4x2 used to determine a change from the CSI-RS
oTh RACFG D-00100 MIMO configured state to the CSI-RS unconfigured state
LST 1 when adaptive CSI-RS configuration is adopted. This
DL 4x4 parameter applies only to LTE FDD and LTE TDD.
CELLC LOFD-0 MIMO
SIRSPA 01003 GUI Value Range: 0~100
RACFG DL 2-
LOFD-0 Layer Unit: %
01060/ MIMO Actual Value Range: 0~100
TDLOF Based
D-00106 Default Value: 40
on TM9
0
DL 4-
TDLAO Layer
FD-001 MIMO
00114 Based
TDLAO on TM9
FD-081
409
CellDlsc MbsfnSf MOD None None Meaning: Indicates whether to configure Multimedia
hAlgo Cfg CELLD Broadcast multicast service Single Frequency
LSCHA Network (MBSFN) subframes. The ten options of this
LGO parameter map to the ten MBSFN subframes. If an
LST option is selected, the corresponding subframe is
CELLD configured. If an option is not selected, the
LSCHA corresponding subframe is not configured. PDSCH
LGO services with enhanced MIMO applied can be
scheduled on configured MBSFN subframes. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: SubFrame0(SubFrame0),
SubFrame1(SubFrame1), SubFrame2(SubFrame2),
SubFrame3(SubFrame3), SubFrame4(SubFrame4),
SubFrame5(SubFrame5), SubFrame6(SubFrame6),
SubFrame7(SubFrame7), SubFrame8(SubFrame8),
SubFrame9(SubFrame9)
Unit: None
Actual Value Range: SubFrame0, SubFrame1,
SubFrame2, SubFrame3, SubFrame4, SubFrame5,
SubFrame6, SubFrame7, SubFrame8, SubFrame9
Default Value: SubFrame0:Off, SubFrame1:Off,
SubFrame2:Off, SubFrame3:Off, SubFrame4:Off,
SubFrame5:Off, SubFrame6:Off, SubFrame7:Off,
SubFrame8:Off, SubFrame9:Off
CellUlsc DopMea MOD LBFD-0 Dynami Meaning: Indicates the Doppler measurement level,
hAlgo sLevel CELLU 0101502 c which is used for selecting a Doppler measurement
LSCHA / Scheduli policy. If this parameter is set to CLASS_0, the
LGO TDLBF ng demodulation reference signal (DMRS) whose signal
LST D-00101 to interference plus noise ratio (SINR) is greater than
CELLU 502 or equal to 5 dB is used in Doppler measurement. If
LSCHA this parameter is set to CLASS_1, the DMRS whose
LGO SINR is greater than or equal to –5 dB is used in
Doppler measurement. This parameter does not take
effect on cells established on an LBBPc. This
parameter applies only to LTE FDD and LTE TDD.
GUI Value Range: CLASS_0(CLASS_0),
CLASS_1(CLASS_1)
Unit: None
Actual Value Range: CLASS_0, CLASS_1
Default Value: CLASS_0(CLASS_0)
6 Counters
7 Glossary
8 Reference Documents
1. Cloud BB Overview
2. CSPC
3. DRX and Signaling Control
4. eMIMO (FDD)
5. eMTC
6. eX2 Self-Management
7. Massive MIMO (FDD)
8. MRO
9. SFN
10. VoLTE
11. Extended Cell Range
12. Scheduling
13. High Speed Mobility
14. Energy Conservation and Emission Reduction
15. USU3910-based Multi-BBU Interconnection
16. Emergency Call
17. Extended CP
18. 3D Beamforming (FDD)
19. Synchronization
20. TDM eICIC (FDD)
21. Virtual 4T4R (FDD)
22. Physical Channel Resource Management
23. Adaptive ICIC
24. Carrier Aggregation
25. General Statements