Professional Documents
Culture Documents
Obsolete: CHECK VALVES - 4,6, and 8 INCH (100,150, and 200mm)
Obsolete: CHECK VALVES - 4,6, and 8 INCH (100,150, and 200mm)
Obsolete: CHECK VALVES - 4,6, and 8 INCH (100,150, and 200mm)
TE
Model F5201 Flange x Groove
1-Valve Body
P-Handhole Cover
3-Handhole Cover
Gasket
4-Seat Ring
LE
5Clapper
B-Clapper Facing
7-Clapper Washer
8-Self-Locking Hex
Hd. Cap Screw
g-Hinge Pin
O
1O-Bushing (4 req’d)
11-Spring
12-Hex Hd. Cap
Screw, l/2”-1 3
UNC x I-314” for 4”
BS
and 6” Valves,
3/4--l 0 UNC x 2”
for 8” Valve
13-Sq. Hd. Steel Plug,
318”NPT
O
FIGURE A
MODEL F52, F520, AND F5201 CHECK VALVES
TD320
Printedin U.S.A. 3-93
t
UP
FLOW
’ 2” CONNECTION
“300 500 1000 2000
TE
OF THE 1 PSI = 0.0689 Bar
F52, F520,AND F5201 FIGURE C
CHECK VALVES NOMINAL PRESSURE LOSS VERSUS FLOW
Valves, as well as the 4, 6, and 8 inch that are listed or approved for fire pro-
WARNING Model F520 and F5201 Check Valves, tection system service. Pipe thread
The Model F52, F520, and F5201 are rated for use at a maximum service connections are per ANSI Standard
Check Valves described herein must pressure of 175 psi (12,l bar). The B1.20.1. The year of manufacture ap-
be installed and maintained in com- Valves may be installed either vet-ti- pears on the Handhole Cover.
pliance with this document, as well as tally and horizontally. In the horizontal
with the applicable standards of the orientation, the Handhole Cover may The nominal pressure losses versus
D-k GASKET
SEALING /
SURFACE
TABLE A
DIMENSIONAL SPECIFICATIONS FOR CUT GROOVE CONNECTIONS
ON MODEL F52 AND F5201 CHECK VALVES
-2-
I CONNECTIONS I
t
H
TE
SECTION “A-A” FRONT RIGHT SIDE
L M DlMErONS; INC~AN~(hlM) s T u v w
Number Size
H J K ,I - ,I ,I I I I I I I I I
(IiO, 6.00 1.81 2.72 4.37
LE1.81 2.72 3.94 3.06
- 8:25 6.06 3.69 2.a4 10.25 3159
F52 (152,4) (46,0) (69,l) (111,O) (46,0) (69,l) (100,l) (77,7) (209,6)(153,9) (93,7) (72,l) (260,4) (91,2)
1.97 3.62 4.38 3.00
(5W (91,9) (111,31 ((7682)
1.56 2.72 3.06 2.59
O
(39.6) (631) (77,7) (658)
1.72 3.62 4.38 2.75
1 F5201 1 (150) 1(152,4)1(43,7)1 (91,9)1(109,5)1(43,7)
I(glsg)1(122,2)1(111,3)1(239,8)1(177 .I. ,
(W3
1 1 8 i 5.75 i 1.94 i 5.00 1 1.94 I 5.00 I 5.94 I 5.81 1 10.88 1 8.72 1 6.18 2.91
BS
FIGURE D
VALVE DIMENSIONS AND CONNECTION LOCATIONS
O
flow rates for the 4,6, and 8 inch (100, A- Bypass or preaction trim (vertical Screws used to secure the Handhole
150, and 200mm) Check Valves are only) Cover are steel per ASTM A307
shown in Figure C. The approximate (Grade A).
friction losses, based on the Hazen B- By-pass
and Williams formula and expressed in The Seat Ring is bronze per ASTM
equivalent length of Schedule 40 pipe C- System drain (vertical or horizontal) B62 (CSSSOO) or 8584 (C84400) and
is 16 feet for each of the valve sizes press-fit within the Body. The Clapper
based on C=lOO, and 22 feet for each D- Automatic drain (horizontal only) or Assembly consists of a Clapper which
valve sizes based on C=l20. The ap- inlet pressure gauge is either cast iron per ASTM A48 (Class
proximate friction losses have been 358) or ductile iron per ASTM A536
calculated on the basis of flow rates E- Outlet pressure gauge (65-45-12) an EPDM rubber Clapper
typically used with each size valve. Facing, a S30400 stainless steel Clap-
F- Automatic drain (horizontal only) per Washer, and a Type 18-8 stainless
Valve dimensions, as well as the loca- s$;;Self-Locking Hex Head Cap
tions of “standard order” and “special G- Inlet pressure gauge
order” pipe thread connections, are
shown in Figure D. Connections which The Valve components are illustrated The Hinge Pin is made from an
are supplied as “standard order” have in Figure A. The Body is cast iron per Sl7400 (Condition HI075 or Hl150)
steel plugs (sealed with a Teflonf ASTM A48 (Class 35B) and the Hand- stainless steel and the Torsion Spring
based pipe thread sealant). The “spec- hole Cover is cast iron per ASTM Al 26 is formed from stainless steel wire per
cial order” connections are shipped (Class B). Exterior surfaces are ASTM A31 3 (S30200). The Hinge Pin
with plastic thread protectors. The fol- painted with a red primer. The Hand- is supported by a a pair of sintered
lowing are typical uses for the various hole Cover Gasket is a i/8 inch bronze Bushings per ASTM 8438
connections: (3,2mm) thick SBR rubber with cotton (Grade I, Type II) which are press-fit
fabric insert. The Hex Head Cap into the Body on either side of the
TE
stalled vertically and primed with After returning the fire protection
water at least to the height of Con- Relieve the system air pressure, if system to service, notify theproper
nection “A”. applicable. authorities and advise those re-
sponsible for monitoring propri-
5. Tighten all flange mounting fasten- Drain the inlet and outlet piping, if etary and IOF central station
ers uniformly, using a cross-draw se- applicable. Verify that the drainage alarms.
quence. The required fasteners are water is being properly disposed of
described in the Orderina Procedure
LE
and that it is not damaging property
Section. Tightening to&es are to or constituting a hazardous condi-
be as indicated below. tion.
Valve Torque, 3. Wait until the sound ofdraining water Seller warrants for a period of one year
Size Ft.Lbs. (Nm) has stopped and/or the inlet and out- from the date of shipment (warranty
O
4” 40-50 (54-66) let pressure gauges read zero pres- period) that the products furnished
6" 50-60(66-81) sure, before performing any mainte- hereunder will be free from defects in
8" 60-75 (81-102) nance work on the fire protection material and workmanship.
system.
BS
6. Grooved end pipe couplings used For further details on Warranty, see
with the Model F52 and F5201 4. Remove the Handhole Cover. Price List.
Check Valves must be listed or ap-
proved for fire protection service and 5. While holding the Spring down by
installed in accordance with the the coils, remove the Hinge Pin. Re-
manufacturer’s instructions. move the Spring and then the Clap-
O
per Assembly.
7. g;~ tighten the Handhole Cover
6. Using a light, check for and remove
any debris that may have become
lodged on top of the Seat Ring. In-
spect the Seat Ring for any damage.
If the Seat Ring has become dented
or creased across its face then the
Valve will have to be replaced. It is
The Model F52, F520, and F5201 impractical to re-face a Seat Ring in
Check Valves do not require any regu- the field.
larly scheduled maintenance. It is rec-
ommended, however, that proper op- 7. Check for and remove any debris
eration of the Valves be verified at which may have become lodged in
least annually in accordance with a the Clapper Facing. If a minor im-
procedure which is appropriate for the perfection remains in the Clapper
application and acceptable to the au- Facing, then turn it over after thor-
thority having jurisdiction. Any impair- oughly cleaning both surfaces with a
ment must be immediately corrected. clean cloth. Replace the Clapper
Facing if necessary.
It is also recommended that the fire
protection systems be inspected by a The Clapper Facing should also be
qualified Inspection Service. replaced if there is any sign of dete-
-4-
Replacement Valve Parts:
Specify: (specify description) for use
with (specify size) inch Model
Orders for Valves and replacement F52IF52OlF5201 Check Valves, PSN The following are the nominal weights
parts must include the description and (specify). for the Valves:
Product Symbol Number (PSN) where
applicable. Product Symbol Numbers 4” (100mm) Model F52/F52O/F5201 4” F52 Valve .............. 45 Ibs. (20,4 kg)
4” F520 Valve ............. 62 Ibs. (28,l kg)
are not assigned to “special order” Check Valves 4” F5201 Valve ............ 51 Ibs. (23,l kg)
Valves. 2-Handhole Cover 6” F52 Valve .............. 68 Ibs. (30,9 kg)
w/Label . . PSN 92-520-l -412 6” F520 Valve ............. 93 Ibs. (42.2 kg)
3-Handhole Cover 6” F5201 Valve ............
Special Instructions: 78 Ibs. (35,4 kg)
Gasket . PSN 92-200-l -413 6” F520 Valve ............. 167 Ibs. (75.8 kg)
The steel bolts and nuts required for +Clapper, 8” F5201 Valve ............ 148 Ibs. (67,l kg)
the attachment of the F520 and F5201 w/Hinge Pin
Check Valve flanges to the mating Bushings .. . PSN 92-200-l -416
B-Clapper Facing . PSN 92-200-l -403
flanges are not provided with the 7-Clapper Washer ... PSN 92-200-l -405
Valves and must be obtained sepa- 8-Self-Locking
rately. The material and dimensions for Hex Head Cap
the fasteners must be in accordance Screw . .. PSN 62-636-l -105
g-Hinge Pin . . . . . . . . . . . PSN 92-200-l-414
with ANSI Standard Bl6.1 (Class 125).
11-Spring . . PSN 92-200-l -415
The bolt material must meet the mini-
mum strength requirements of ASTM
6” (150mm) Model F52/F52O/F5201
A307 (Grade B) and the nut material Check Valves
must meet the minimum strength re- P-Handhole Cover
quirements of ASTM A563 (Grade A). w/Label . . . . . , . . . PSN 92-520-l -412
3-Handhole Cover
Standard Order Valves: Gasket . . . . PSN 92-200-I -613
TE
Specify: (specify size) inch Model w/Hinge Pin
(specify number) Check Valve, PSN Bushings . PSN 92-200-l -616
(specify). B-Clapper Facing PSN 92-200-l -803
7Clapper Washer . ... PSN 92-200-l -605
8-Self-Locking
Model F52 Check Valve
Hex Head Cap
4” (10Omm) _. .. . . .PSN 52-520-l-113
Screw ..... PSN 62-636-l -105
6” (150mm) .. .PSN 52-520-l-115
LE
g-Hinge Pin . . . . . . . .
1 l-Spring . . . . . ..
PSN 92-200-l -614
PSN 92-200-I-61 5
Model F520 Check Valve
4” (IOOmm) . . . . . . . . . . .PSN 52-520-l-013
6” (f50mm) . . . . . . . .PSN 52-520-I-015
8” (200mm) Model F52/F52O/F5201
8” (200mm) . . . . . . . . . . . . . . PSN 52-520-I -016
Check Valves
P-Handhole Cover
Model F5201 Check ValVe
O
w/Label . . . . . . . . PSN 92-520-l -812
4” (100mm) . . . .PSN 52-520-l-413 3-Handhole Cover
6” (150mm) .PSN 52-520-l-615 Gasket . PSN 92-200-I -813
8” (200mm) .. PSN 52-520-l -816 5-Clapper,
w/Hinge Pin
BS
-5-
TE
LE
O
BS
O
@ Reg. trademarkof GRINNELL CORPORATION, 3 TYCO PARK, EXETER, NH 03833 A tyccllNTERNATIONAL LTD. COMPANY