Professional Documents
Culture Documents
Firelock Fire-Pac For Firelock NXT Valves: Installation, Maintenance, Testing, and Wiring Manual
Firelock Fire-Pac For Firelock NXT Valves: Installation, Maintenance, Testing, and Wiring Manual
WARNING
WARNING
• Read and understand all instructions before attempting to install Victaulic piping products.
• Depressurize and drain the piping system before attempting to install, remove, or adjust
Victaulic piping products.
• Wear safety glasses, hardhat, and foot protection during installation.
Failure to follow these instructions could result in serious personal injury and/or property
damage.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G I-745
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G I-745_1
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
I-745_2 REV_G
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
D M
Front of
Cabinet E
J G
H
L K
I Top View
The drawings shown above are for Fire-Pac cabinets containing 1 1/2 – 2-inch/48.3 – 60.3-mm valve sizes.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G I-745_3
FireLock Series 745 Fire-Pac Figure Number System
I-745_4
S P 040 745 05 B 1 B 1 1 SERIES 745
www.victaulic.com
Style Applicable Compressor Air Maintenance Color
Class Type Size Number Trim Selection Panel Design Wiring Code Selection Selection Selector
S A - Dry 014 1 ½” 745 01 - Dry Actuated A - No Panel 1 - Std. (US) UL Class B B - 1/6 hp †† 1 - Compressor (No Air Maintenance Trim) ** 1 - Red
D - Deluge 020 2” 1A - Dry Actuated with Added Control Valve B - PDRP-2001 Panel (Includes Two - 12V, 12AH Batteries) 2 - Canada ULC Class B C - ¼ hp †† 2 - Air Maintenance Trim Assembly (AMTA) ***@ 9 - Special #
P - Preaction 761 76.1 mm # 02 - Dry Actuated/Accelerated † C - PDRP-2001 Panel/4XTM 3 - US 220V Class B D - 1/3 hp †† 3 - Air Maintenance Trim Assembly with Tank @
165 165.1 mm # 2A - Dry Actuated/Accelerated with Added Control Valve † D - PDRP-2001 Panel/4XTM/ANN-80 4 - Standard Class A E - ½ hp †† 4 - No Compressor
03 - Deluge Pneumatic E - PDRP-2001 Panel/4XTM/ANN-I/O F - ¾ hp ††
024 2 ½” 5 - Canadian Class A 9 - Special #
3A - Deluge Pneumatic with Added Control Valve F - PDRP-2001 Panel/4XTM/ANN-RLY G - 1 hp ††
030 3” 04 - Deluge Electric G - PDRP-2001 Panel/4XTM/ANN-80/ANN-I/O 6 - 220V Class A H - None †††
040 4” 4A - Deluge Electric with Added Control Valve H - PDRP-2001 Panel/4XTM/ANN-80/ANN-RLY 9 - Special #
060 6” 05 - Preaction Single-Interlocked, Electric I - PDRP-2001 Panel/4XTM/ANN-I/O/ANN-RLY
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL
Valve
7H - Preaction AutoConvert Double-Interlocked, Electric-Pneumatic/Electric
7J - Preaction AutoConvert Double-Interlocked, Electric-Pneumatic/Electric with Added
Control Valve
08 - Preaction, Double-Interlocked Pneumatic/Pneumatic
8A - Preaction, Double-Interlocked Pneumatic/Pneumatic with Added Control Valve
09 - Special #
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
# Contact Victaulic for pricing and availability @ When ordering the Air Maintenance Trim Assembly along with a compressor, the system must contain a tank (Option 3)
** Valve equipped with an accelerator requires an Air Maintenance Trim Assembly † Requires a Regulated Air Maintenance Trim Assembly (Option 3) with a tank
*** Air Maintenance Trim Assembly without compressor is for use with external, tank-mounted air compressor or shop air †† Applies to 2 ½ - 6-inch/73.0 - 168.3-mm Fire-Pac cabinets only
ˆ Electric Release with panel cross-zoned ††† When the 220-Volt wiring code is specified, the compressor must be ordered as ¾-hp or “None”
I-745
REV_G
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
This option includes the base panel with two 12AH batteries.
The base panel provides the alarm and trouble relays. The
B PDRP-2001 Panel with Two 12-Volt, 12AH Batteries alarm indicates when the valve trips, and the trouble indicates
a technical difficulty (i.e. loss of power, loose wire, etc.). Three
programmable relay contacts are provided for remote signaling.
This option includes option “B,” plus a supervised output for local
C PDRP-2001 Panel with 4XTM energy municipal box transmitter and alarm and trouble reverse
polarity.
D PDRP-2001 Panel with 4XTM/ANN-80 This option includes option “C,” plus a remote LCD annunciator
that mimics the information displayed on the FACP LCD display.
This option includes option “C,” plus an LED driver that can be
E PDRP-2001 Panel with 4XTM/ANN-I/O used as an interface with the FACP to drive most customized
graphic annunciators.
F PDRP-2001 Panel with 4XTM/ANN-RLY-10 This option includes option “C,” plus 10 additional, programmable
Form-C relays.
G PDRP-2001 Panel with 4XTM/ANN-80/ANN-I/O This option combines the features of option “D” and option “E”.
H PDRP-2001 Panel with 4XTM/ANN-80/ANN-RLY-10 This option combines the features of option “D” and option “F”.
I PDRP-2001 Panel with 4XTM/ANN-I/O/ANN-RLY-10 This option combines the features of option “E” and option “F”.
J PDRP-2001 Panel with ANN-80 This option includes option “B,” plus a remote LCD annunciator
that mimics the information displayed on the FACP LCD display.
M PDRP-2001 Panel with ANN-80/ANN-I/O/ANN-RLY-10 This option includes option “K,” plus 10 additional, programmable
Form-C relays
This option includes option “B,” plus an LED driver that can be
N PDRP-2001 Panel with ANN-I/O used as an interface with the FACP to drive most customized
graphic annunciators.
O PDRP-2001 Panel with ANN-RLY-10 This option includes option “B,” plus 10 additional, programmable
Form-C relays.
P PDRP-2001 Panel with ANN-I/O/ANN-RLY-10 This option combines the features of option “N” and option “O”.
9 Special –
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G I-745_5
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
INTERNAL VIEW – FIRE-PAC CABINET CONTAINING 1 1/2 – 2-INCH/48.3 – 60.3-MM VALVE SIZES
The front view shown below is of a typical 1 1/2-inch/48.3-mm Series 768 FireLock NXT™ Dry Valve. The brackets for the manual pull station and
pressure gauges, along with brackets for other components, have been removed for clarity.
Electrical
Riser Out Enclosure
to System
Air Compressor*
Air Tank*
Fast-Fill Ball Valve of the Air Slow-Fill Ball Valve of the Air
Maintenance Trim Assembly# Maintenance Trim Assembly#
Manual Pull
Station
Connection for
Multi-Unit From Water
Installations Supply ‡
* Optional
# Air Maintenance Trim Assembly is optional To Drain
‡ Can be connected from the left or right side of the cabinet Connection
INTERNAL VIEW – FIRE-PAC CABINET CONTAINING 1 1/2 – 2-INCH/48.3 – 60.3-MM VALVE SIZES
The back view shown below is of a typical 1 1/2-inch/48.3-mm Series 768 FireLock NXT™ Dry Valve. Brackets have been removed for clarity.
Electrical
Enclosure Riser Out to
System
Air Compressor*
* Optional
# Air Maintenance Trim
Assembly is Optional
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
I-745_6 REV_G
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
INTERNAL VIEW – FIRE-PAC CABINET CONTAINING 1 1/2 – 2-INCH/48.3 – 60.3-MM VALVE SIZES
The left-side view shown below is of a typical 1 1/2-inch/48.3-mm Series 768 FireLock NXT™ Dry Valve. Brackets have been removed for clarity.
Air Compressor*
Door Handle
* Optional
INTERNAL VIEW – FIRE-PAC CABINET CONTAINING 1 1/2 – 2-INCH/48.3 – 60.3-MM VALVE SIZES
The right-side view shown below is of a typical 1 1/2-inch/48.3-mm Series 768 FireLock NXT™ Dry Valve. Brackets have been removed for clarity.
Door Handle
Diaphragm-Charge-
Line Ball Valve
Manual Pull Station
* Optional
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G I-745_7
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
INTERNAL VIEW – FIRE-PAC CABINET CONTAINING 2 1/2 – 6-INCH/73.0 – 168.3-MM VALVE SIZES
The front view shown below is of a typical 6-inch/168.3-mm Series 769 FireLock NXT™ Preaction Valve with Double-Interlocked, Electric/Pneumatic
Release trim. The brackets for the manual pull station and pressure gauges, along with brackets for other components, have been removed for clarity.
Air
Compressor*
Diaphragm
Pressure Gauge Additional Water Supply
Main Control Valve*
System Air
Pressure Gauge Air Tank*
Water Supply
Pressure Gauge Air Supervisory
Pressure Switch
Upper Chamber
Pressure Gauge for System Main
the Series 767 Drain Valve
Electric/Pneumatic Water Supply
Actuator Main Drain Valve
Diaphragm-
Charge-Line
Ball Valve Water Supply Main
Control Valve
Manual Pull
Station
* Optional To Drain
‡ Can be connected from the left or right side of the cabinet Connection
INTERNAL VIEW – FIRE-PAC CABINET CONTAINING 2 1/2 – 6-INCH/73.0 – 168.3-MM VALVE SIZES
The back view shown below is of a typical 6-inch/168.3-mm Series 769 FireLock NXT™ Preaction Valve with Double-Interlocked, Electric/Pneumatic
Release trim. Brackets have been removed for clarity.
Electrical
Enclosure
Riser Out to
System
Air Compressor*
Fast-Fill Ball Valve of the Air
Maintenance Trim Assembly#
Air Tank* Slow-Fill Ball Valve of the Air
Maintenance Trim Assembly#
Air Regulator of the Air
Maintenance Trim Assembly#
Air Manifold
Air Tank Bleed
Valve
Alarm Pressure
Switch
* Optional
# Air Maintenance Trim
Assembly is Optional
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
I-745_8 REV_G
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
INTERNAL VIEW – FIRE-PAC CABINET CONTAINING 2 1/2 – 6-INCH/73.0 – 168.3-MM VALVE SIZES
The left-side view shown below is of a typical 6-inch/168.3-mm Series 769 FireLock NXT™ Preaction Valve with Double-Interlocked, Electric/
Pneumatic Release trim. Brackets have been removed for clarity.
Electrical
Enclosure
Riser Out to System
Air Compressor*
System Main
Alarm Pressure Switch Drain Valve
* Optional
INTERNAL VIEW – FIRE-PAC CABINET CONTAINING 2 1/2 – 6-INCH/73.0 – 168.3-MM VALVE SIZES
The right-side view shown below is of a typical 6-inch/168.3-mm Series 769 FireLock NXT™ Preaction Valve with Double-Interlocked, Electric/
Pneumatic Release trim. Brackets have been removed for clarity.
Electrical
Enclosure
Riser Out to
System
Door Handle
System Main
Drain Valve Alarm Pressure
Water Supply Switch
Main Drain Valve
Drip Cup
with Cap
* Optional
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G I-745_9
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
a.) The diaphragm pressure gauge, system air pressure gauge, water
supply pressure gauge, and manual pull station are located on
front of the cabinet for system operation monitoring.
3. Bleed the valve, located at the bottom of the air tank, once every
three months to remove any moisture from the line.
4. To perform maintenance on any internal valve components (i.e.
replacing the clapper assembly, cover plate gasket, etc.), refer to
the installation, maintenance, and testing manual for the applicable
trim configuration.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
I-745_10 REV_G
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
Bracket (Mounted
to Cabinet Frame)
Compressor
4
Bill of Materials
5
Item Qty. Description
1 4 Bolt
2 8 Flat Washer
3 8 Vibration Isolation Mount
4 4 Lock Washer
5 4 Nut
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G I-745_11
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
I-745_12 REV_G
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
TERMINOLOGY b.) For enclosures that contain circuit breakers, the breaker shall be
used as supplemental branch protection. Primary protection shall
The following table contains terminology that will be used throughout
be used when installing the Fire-Pac. Circuit breakers can be used
this section and descriptions for each item.
as a disconnect switch to perform maintenance or replacement
of a device. The operation of each circuit breaker is designed
Item Description to report a breaker that has either tripped or has been operated
manually (except for the enclosure light). For localities that will not
PDRP-2001 (120 Volt) allow supplemental overload protection on the primary fire alarm
Six zone, 24-volt deluge/preaction control
PDRP-2001E (220 Volt) panel for single and dual hazard applications riser, the breakers can be bypassed (please contact Victaulic for
instructions). When any maintenance or work is being performed,
proper lockout/tagout procedures must be followed.
c.) For Fire-Pac cabinets that contain a fire alarm control panel, two
CAC-5X Optional - Used to convert Class “B” style
wiring connections to Class “A” style 12-amp/hour batteries are provided; these batteries are intended
for general use and shall be connected and disconnected only with
primary power supplied to the fire alarm control panel. All battery
Optional - Used to provide a supervised calculations shall be generated in accordance with installation
4XTM output for local energy municipal box requirements. Supplied batteries shall not be used if the battery
transmitter and alarm and trouble reverse
polarity requirement calculations are greater than the capacity of the
supplied batteries (contact Victaulic for additional battery sizes).
Batteries that are greater than 18-amp/hour shall be installed in a
Optional - Remote LCD annunciator that separate, approved enclosure.
ANN-80 mimics the information displayed on the
FACP LCD display d.) Optional modules (4XTM, CAC-5X, etc.) can be configured into
the Fire-Pac when a fire alarm control panel is installed. The
terminal blocks and wiring are the same; therefore, connections
Optional - LED driver module provides for optional modules may be available. DO NOT perform any
ANN-I/O a connection to a user-supplied graphic
annunciator function unless the specific module has been specified during the
ordering process. EXAMPLE: Terminal block TBD has connections
for alarm, trouble, and municipal box. If this option has not been
Optional - Provides 10 programmable Form-C
relays that can be programmed for various ordered, the terminal will not have any function. If an optional
ANN-RLY-10 functions: alarm, trouble, supervisory, AC loss, device is needed at a later time, it can be retrofitted easily into the
waterflow delay, input zones, and silenceable
alarm Fire-Pac using the pre-wired connections. Contact Victaulic for the
required parts and installation instructions.
• FACP - Fire Alarm Control Panel e.) Fire-Pac cabinets that are not provided with a fire alarm control
• LCD - Liquid Crystal Display panel, two terminal blocks are provided for supply power, device
• LED - Light-Emitting Diode supervision, and valve release. All supervisory connections are
• Class “B” - Two-Wire Configuration considered to be “dry” contacts. To use supervisory contacts for
• Class “A” - Four-Wire Configuration functions that require current to flow through the installed devices,
refer to the corresponding device listing, along with the factory wire
IMPORTANT INFORMATION size. Terminal block functions and connections may vary between
Fire-Pac styles and options.
DANGER
f.) For systems without a fire alarm control panel and where a
• Only qualified electricians should connect solenoid coil (Series 753-E Solenoid or Series 767 Electric/
incoming power to the Fire-Pac. Pneumatic Actuator) is used to release or trip a valve, fire alarm
panel compatibility shall be considered to prevent improper valve
Failure to follow this instruction could result in
operation or damage to the fire alarm control panel. Coordination
death or serious personal injury.
shall be made between the authority having jurisdiction (AHJ), fire
alarm panel installer, and the building owner to ensure all system
a.) A separate, keyed electrical enclosure is provided for the installer
devices meet the intent of the work to be performed. Contact
to wire the supply power, initiating devices (such as pull stations
Victaulic for an updated compatibility document.
and detectors), notification devices (such as horns and strobes),
and other auxiliary connections. Two knock-out holes are provided g.) Refer to the following page for a breakdown of electrical
on top of the enclosure to allow for the separation of power- schematics according to trim selection. NOTE: The applicable
limited and non-power-limited wiring. All installation wiring shall schematic is provided in the cabinet.
be performed only in the electrical enclosure by utilizing the top
unwired screw terminals. Fire alarm wiring shall be performed in
accordance with NFPA 72, NFPA 70, and other local regulations.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G I-745_13
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
1A Dry Actuated with Additional Water Supply Main Control Valve W-SCHEM-745-050
2A Dry Actuated with Accelerator and Additional Water Supply Main Control Valve W-SCHEM-745-050
3A Deluge Pneumatic (Dry Pilot) with Additional Water Supply Main Control Valve W-SCHEM-745-050
4A Deluge Electric with Additional Water Supply Main Control Valve W-SCHEM-745-000
5A Preaction Single-Interlocked, Electric with Additional Water Supply Main Control Valve W-SCHEM-745-020
5C Preaction AutoConvert Single-Interlocked, Electric with Additional Water Supply Main Control Valve W-SCHEM-745-060
6A Preaction Double-Interlocked, Electric with Additional Water Supply Main Control Valve W-SCHEM-745-020
6C Preaction AutoConvert Double-Interlocked, Electric with Additional Water Supply Main Control Valve W-SCHEM-745-060
7A Preaction Double-Interlocked, Pneumatic/Electric with Additional Water Supply Main Control Valve W-SCHEM-745-020
7C Preaction Double-Interlocked, Pneumatic/Electric/Electric with Additional Water Supply Main Control Valve W-SCHEM-745-040
7E Preaction Single-Interlocked, Pneumatic with Additional Water Supply Main Control Valve W-SCHEM-745-050
7G Preaction AutoConvert Double-Interlocked, Pneumatic/Electric with Additional Water Supply Main Control W-SCHEM-745-060
Valve
7H Preaction AutoConvert Double-Interlocked, Electric-Pneumatic/Electric W-SCHEM-745-060
7J Preaction AutoConvert Double-Interlocked, Electric-Pneumatic/Electric with Additional Water Supply Main W-SCHEM-745-060
Control Valve
08 Preaction, Double-Interlocked Pneumatic/Pneumatic W-SCHEM-745-030
8A Preaction, Double-Interlocked Pneumatic/Pneumatic with Additional Water Supply Main Control Valve W-SCHEM-745-030
09 Special –
* This designation corresponds with the “Trim Selection” section of the FireLock Fire-Pac Figure Number System chart on page 4.
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
I-745_14 REV_G
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
Before any connections are made in the Fire-Pac, the primary electrical
supply shall be de-energized, and the proper lockout/tagout procedure
shall be followed. All primary wiring and circuit breakers shall be
sized properly for the application. Refer to Figure 1 and the following
instructions.
Figure 1 - Supply Power Terminal Block
TB1 Input
120 VAC, 60 Hz
L1 N G
Without Fire Alarm Control Panel
1 2 3
1 0.74 115-60-1
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G I-745_15
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
NOTIFICATION CIRCUITS
Three supervised Class B notification devices can be connected to
TBA the Fire-Pac. Alarm, trouble, and supervisory conditions will report as
separate signal on terminal block TBA. Each output can have a 3-amp
maximum current draw, and at no time can the DC output exceed 7
amps. Refer to the PDRP-2001 Device Compatibility Appendix for listed
devices that can be connected to these outputs. Refer to Figure 4 and
Zone 1B Zone 2B the following instructions.
1. Install and wire all field devices with a 4.7 K ohm resistor on the Figure 4 - Notification Circuit
end device.
2. Before landing wires on the terminal block, check the circuit for
integrity (open, short, loop resistance, etc.). H H H
3. Land wires to the appropriate connection point on TBA (+/-).
4. Unused inputs shall be terminated with 4.7 K ohm resistors across
terminals. Strobe Strobe Strobe
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
I-745_16 REV_G
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
TB2
Figure 5 - Standard Relay Contacts C
R2 NC TROUBLE
TBC NO
Trouble C
Alarm (Fail Safe) Super
R3 NC SUPERVISORY
NO
TB4
C
R4 NC IN ZONE 1
NO
R5 NC IN ZONE 2
NO
TB5
R6 NC IN ZONE 3
4XTM OPTION NO
The 4XTM option provides a supervised output for a local municipal box C
transmitter in addition to alarm and trouble reverse polarity. The module R7 NC IN ZONE 4
is wired to terminal block TBD, which contains connections for remote NO
alarm, remote trouble, and municipal box. All outputs are non-power-
TB3
C
limited and can be disabled with a disconnect switch located on the
4XTM module. R8 NC IN ZONE 5
NO
R9 NC IN ZONE 6
NO
TB6
R10 NC DISCHARGE
NO
OPTIONAL ANN-RLY
RELAY MODULE
TB3 - FACP PANEL
389
B
390
A
ANN-BUS
391
+
392
-
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G I-745_17
Field Wiring Diagram
I-745_18
S = Smoke Detector Strobe = Visual Notification
M = Manual Pull Station = Normally-Open Switch Contact
H = Audible Notification
NOTES:
1. This diagram is a general overview of a typical
Fire-Pac. Refer to the Installation, Maintenance,
and Testing manual for the specific system.
2. Refer to the Fire-Pac Installation, Maintenance,
Testing, and Wiring Manual and the manual for
the Fire Alarm Control Panel for specific
installation instructions.
* Equipment cannot be installed. These devices
are specific to the type of Fire-Pac ordered and is
considered optional hardware.
** Tamper switch is located under each pressure
switch for the ULC version ONLY.
*** No end-of-line resistor (EOLR) is needed
when using the Class A module.
REV_G
NOTES
REV_G I-745_19
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
I-745_20 REV_G
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
2=TYPE RELEASE CIR 1 UPSUPV SHORTS 10) Return to INPUT ZONES, Press
10) Return to OUTPUT CIRCUITS, Press 13) Return to INPUT ZONES, Press
12) Set to the following 15) Go to EDIT mode and set the following
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G I-745_21
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
2) Select 1=OUTPUT 1 11) Select 1=ZONE 4 (For Trim Selections 7B and 7C, go to step “A”
on the following page)
3) Set to the following
12) Go to EDIT mode and set the following
1=ENABLED YES
1=ENABLED
2=TYPE ALARM NAC
2=SUPERVISORY AR
4) Return to OUTPUT CIRCUITS
3=OUTPUT CIRCUIT MAP
5) Select 2=OUTPUT 2
13) Go to 2=DESCRIPTION
6) Set to the following
14) Type “LOW/HIGH AIR”
1=ENABLED YES
15) Return to INPUT ZONES, Press
2=TYPE RELEASE CIR 1 UPSUPV SHORTS
16) * Select 2=ZONE 5
7) Return to OUTPUT CIRCUITS
17) Go to EDIT mode and set the following
8) Select 3=OUTPUT 3
1=ENABLED
9) Set to the following
2=TYPE SUPERVSRY AR
1=ENABLED YES
3=OUTPUT CIRCUIT MAP
2=TYPE SUPV BELL NAC
18) Press , 2=DESCRIPTION
10) Return to OUTPUT CIRCUITS, Press
19) Type “PS COVER”
11) Select 1=OUTPUT 4
20) Return to INPUT ZONES, Press
12) Set to the following
21) Select 3=ZONE 6
1=ENABLED YES
22) Go to EDIT mode and Set the following
2=TYPE TROUBLE BELL NAC
1=ENABLED
13) Return to main menu PROGRAMMING
2=TYPE SUPERVSRY AR
INPUT ZONES 3=OUTPUT CIRCUIT MAP
1) Select 2= INPUT ZONES 23) Press , 2=DESCRIPTION
2) Select 1=ZONE 1 24) Type “WATER/AIR COMP OFF”
3) Go to EDIT mode and set the following 25) Return to PROGRAMMING
1=ENABLED 26) For Trim Selection 6B (Double-Interlocked, Electric), go to step “B”
on the following page.
2=TYPE 2-WIRE SMOKE
3=OUTPUT CIRCUIT MAP
1=ALARM NAC YES
2=RELEASE 1 YES *Note: ULC option only
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
I-745_22 REV_G
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
A. DOUBLE-INTERLOCKED, ELECTRIC-PNEUMATIC/ELECTRIC
(TRIM SELECTIONS 7B AND 7C)
1) Follow to step 11 on the previous page
2) Go to EDIT mode and set the following
1=ENABLED
2=TYPE COMBO SUP AR
3=OUTPUT CIRCUIT MAP
1=ALARM NAC YES
2=RELEASE 1 YES
3) Go to 2=DESCRIPTION
4) Type “LOW/HIGH AIR”
CROSS-ZONED
1) Select 1=CROSS INPUT ZONES
2) Select 1=RELEASE 1 GROUPS
3) Select 1=NONE
4) 1=ZONE 1 YES
5) Press
6) 1=ZONE 4 YES
7) ESC to REL 1 CROSS GROUPS
1= X 1 4
2= NONE
8) Select 2=NONE
9) Select ZONE 2 and 4
10) ESC to REL 1 CROSS GROUPS (Confirm Setting)
1= X 1 4
2= X 2 4
11) Return to step 15 on the previous page
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
REV_G I-745_23
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
PROGRAMMING MATRIX FOR DRAWINGS 6) Go to EDIT mode and set the following
SCHEM-745-030 AND SCHEM-745-050 1=ENABLED
(TRIM SELECTIONS 08, 01, AND 02) 2=TYPE PULL STATION
3=OUTPUT CIRCUIT MAP
SYSTEM SET UP 1=ALARM NAC YES
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY. © 2010 VICTAULIC COMPANY. ALL RIGHTS RESERVED. PRINTED IN THE USA.
I-745_24 REV_G
NOTES
REV_G I-745_25
INSTALLATION, MAINTENANCE, TESTING, AND WIRING MANUAL I-745
FireLock® Fire-Pac for FireLock NXT™ Valves
SERIES 745
I-745