Professional Documents
Culture Documents
High Tensile Bolt8.8
High Tensile Bolt8.8
Non-Preloaded
Issue: 2
High Tensile Structural Bolts & Nuts Date: 01/09/07
Approved: M.R. Tiddy
- Non-Preloaded 8.8 Page: 1 of 6
Thread size d M12 M16 M20 M24 M30 M36 Fully Threaded Bolts / Setscrews & Standard Thread Bolts
General Requirements BS 4190
p pitch of thread 1.75 2 2.5 3 3.5 4
Threads BS 3643 Parts 1 & 2 tolerance class 6g
a max. 5.25 6 7.5 9 10.5 12
Materials & Manufacture BS EN ISO 898-1 Property Classes 8.8
max. 0.6 0.8 0.8 0.8 0.8 0.8
c Mechanical Properties BS EN ISO 898-1 Property Classes 8.8
min. 0.15 0.2 0.2 0.2 0.2 0.2
Dimensions & Tolerances DIN 933 (Setscrews) & DIN 931 (Bolts)
da max. 13.7 17.7 22.4 26.4 33.4 39.4
Self Colour / Black BS 4190 - as processed
dw min. 17.4 22.5 27.7 33.2 42.7 51.1 Finish /
Zinc Electroplated BS 7371-3 or BS EN ISO 4042
Coatings
e min. 21.1 26.75 32.95 39.55 50.85 60.79
Hot Dip Galvanized BS 729 & BS 7371 Part 6
nom. 7.5 10 12.5 15 18.7 22.5 Product Marking BS EN ISO 898-1
k max. 7.68 10.18 12.85 15.35 19.12 22.92
min. 7.32 9.82 12.15 14.65 18.28 22.08 Tolerance on nominal length for Fully Threaded
r min. 0.6 0.6 0.8 0.8 1 1 Bolts / Setscrews and Standard Thread Bolts
s nom. max. 19 24 30 36 46 55
min. 18.67 23.67 29.16 35 45 53.8 Nominal Length mm
Tolerance
Dimensions apply prior to coating Over Up to and including
The table shows popular diameters, other diameters can be supplied provided the quantity is 30 50 ± 1.25
sufficient to warrant manufacture. 50 80 ± 1.5
80 120 ± 1.75
120 180 ±2
180 250 ± 2.3
Certification
M16
8.8
�
�
50
�
��
�
�
8
M
8.
�
� � � Standard Thread Bolts
The actual arrangement of the marking may
vary from that shown
�
�
�
��
��
��� �� ���
Proof Load of Nuts
mm2 kN kN
��
��
Characteristic Standard
Washers
General Requirements BS 4320 Section 2 Normal Diameter (Form E)
Materials & Manufacture BS 4320 Section 2
Dimensions & Tolerances BS 4320 Section 2 (Form E) or DIN 125
Self Colour / Black BS 4190 - as processed
Finish /
Zinc Electroplated BS 7371-3 or BS EN ISO 4042
Coatings
Hot Dip Galvanized BS 729 & BS 7371 Part 6
Dimensions of Washers
Whilst this information is provided in good faith, no member of the Andaray group of companies shall be under any responsibility
All dimensions are in millimetres or liability in respect of errors or information that is found to be incorrect or for any relience the user may place on it.