Professional Documents
Culture Documents
Digital Surround Sound Receiver: FR960 FR970
Digital Surround Sound Receiver: FR960 FR970
Digital Surround Sound Receiver: FR960 FR970
Français
Français.................................................24
Español
Español .................................................44
Deutsch
Deutsch.................................................64
Nederlands
Nederlands ...........................................84
Italiano
Italiano................................................104
Scope of supply..................................................................................4
Maintenance ......................................................................................4 This receiver is supplied including:
Setup ..................................................................................................4 – an universal remote control
Environmental information.................................................................4 – 2 batteries for the remote control, size AA
Trademark acknowledgment..............................................................4
– a system bus cable for the CINEMA LINK connection
Controls .................................................................................................5
– a loop antenna
Remote control – a wire antenna
Remote control usage........................................................................6
Remote control buttons .....................................................................7 – this instruction booklet
Programming the universal remote control .......................................8
Connectors............................................................................................9
Maintenance
Connections
Audio connections............................................................................10 Clean the receiver with a soft,
Digital audio connections ................................................................10 slightly dampened, lint-free cloth. Do
System control bus, CINEMA LINK .................................................11 not use any cleaning agents as they
Video connections............................................................................11
Mains ...............................................................................................12 may have a corrosive effect.
Speaker connections........................................................................12
TV as the center speaker .................................................................12
Antenna connections .......................................................................12 Do not expose the receiver to
System setup humidity, rain, sand or excessive heat
Positioning of the speakers .............................................................13
Speaker setup and testing...............................................................13
(caused by heating equipment or
Power handling ................................................................................13 direct sunlight).
Headphones .....................................................................................13
Display.................................................................................................14 Setup
Menus
Receiver menu..................................................................................15
If you have stacked the components of your system, the
TV menu ...........................................................................................16 receiver must be on top. Place the receiver on a flat, hard,
Source selection stabile surface. Do not cover any vents and leave 50 cm
SOURCE SELECTOR..........................................................................17 above and 10 cm left and right of the receiver free for
Reassigning a source selection .......................................................17 ventilation.
Using one source selection for two or more appliances ................17
Playback, recording
For good reception the loop antenna should not be placed on
Playing a source ...............................................................................18
Adjusting the sound .........................................................................18 top of or beneath VCRs, CD recorders, DVD players, TVs and
Recording from a source..................................................................18 other radiation sources.
Recording from the digital output ...................................................18
Surround sound Environmental information
About surround sound......................................................................19
Switching surround sound ...............................................................19 All redundant packing material has been omitted. We have
Surround sound settings..................................................................19 done our utmost to make the packaging easily separable into
Tuner three mono materials: cardboard (box), polystyrene foam
Tuning to radio stations ...................................................................20
(buffer) and polyethylene (bags, protective foam sheet).
Switching FM sensitivity .................................................................20
Storing radio stations ......................................................................20
Tuning to stored radio stations........................................................21 Your set consists of materials which can be recycled if
Resorting stored radio stations .......................................................21 disassembled by a specialized company. Please observe the
Naming radio stations .....................................................................21
local regulations regarding the disposal of packing materials,
Clearing station names....................................................................21
RDS R..............................................................................................22 exhausted batteries and old equipment.
RDS News and Traffic Announcement ............................................22
Technical data Trademark acknowledgment
Receiver............................................................................................22
Manufactured under license from Dolby Laboratories.
Troubleshooting
Warning............................................................................................23 “DOLBY”, “DOLBY DIGITAL”, “PRO LOGIC” and the double-D
Troubleshooting................................................................................23 symbol 2 are trademarks of Dolby Laboratories. Confidential
unpublished works. © 1992–1997 Dolby Laboratories. All
rights reserved.
1 2 3 4 5 6 7
English
VOLUME
R
SELECTO
SOURCE
DVD
PHONO
TUNER
UN D CE NT ER
EM A SO
DIG ITA L CIN CD
HALL
8
LINK ROUND
CINEMA 3D SUR
CDR /
Y
STANDB TAPE
POWER /
AV
TV
VCR
NEXT
SS
BASS
TREBLE
9
LOUDNE
EXIT
PREV. /
TER / OK
0
SENS.
AM/FM
TUNER
MENU
SETUP
MODE NEWS
T/A
ND SURR.
SURROU TEXT
RADIO
SING
ND PROCES
SURROU L SOUND RE
3D DIGITA
PHONES CO
!
ON/OFF DU ET
ME
AV / GA
FRONT
≤ £ ™ ¡)( * & ^ % $ # @
1 POWER / STANDBY.......Switches the receiver on and off. % TUNER PRESET X MENU NAVIGATOR
2 CINEMA LINK ................Switches the system control bus TUNER: switches to the next and
between the receiver and the TV previous stored radio station.
on and off. MENU: moves upwards and
3 ..........................................Sensor for the infrared remote downwards.
control. ^ 1 PREV. / EXIT ...............TUNER: searches radio stations.
4 3D SURROUND ..............Control light for virtual 3D MENU: switches to the previous
surround. menu level.
5 HALL ................................Control light for HALL. & SETUP MENU ................Switches the menu on and off.
6 ..........................................Display * SENS. ..............................Switches between low and high
7 SOURCE SELECTOR ......Selects the different audio and tuner sensitivity.
video connectors. ( NEWS/TA........................Switches the RDS news and
8 VOLUME..........................Increases and decreases the RDS traffic announcement on
volume level. and off.
9 FRONT AV.......................Selects the FRONT AV / GAME ) TUNER AM/FM ..............Switches the wavebands of the
input (FR 970 only). tuner.
0 TREBLE............................Adjusts the treble when used in ¡ RADIO TEXT ...................Scrolls through the different RDS
combination with VOLUME. information.
! BASS ...............................Adjusts the bass when used in ™ SURR. MODE..................Switches through the different
combination with VOLUME. surround effects.
@ LOUDNESS .....................Switches LOUDNESS on and off. £ 3D SURROUND ..............Switches virtual 3D surround on
# NEXT 2 ...........................TUNER: searches radio stations. and off.
MENU: switches to the next ≤ SURROUND ON/OFF .....Switches the surround sound on
menu level. and off.
$ ENTER / OK.....................Confirms selected menu values.
The remote control remains tuned to the selected source until MENU OK
another source button on the remote control is pressed. This
enables you to operate additional sources (i. e. winding a
tape) without changing the source on the receiver.
É
A ATV
NEWS/TA Ç
CHANNEL/TRACK LOUDNESS SOUND
í ë ±
REC CANCEL FR.D. INDEX
AUDIO Å T-C
English
±SOUND....................Scrolls through the different smart
H MUTE .....................Mutes the sound of the receiver. sounds.
2 ................................Switches the receiver to standby. REC, DVD AUDIO..........CDR, VCR: Starts recording.
PHONO, TUNER, CD, DVD: Switches audio tracks.
CDR/TAPE, TV, CANCEL, DVD ...........CD, CDR, SAT, VCR: Clears a
VCR, SAT, DVD..............Switches the remote control to the program, cancels selections.
commands of the different products. DVD: Switches the view angle.
Selects the sources if pressed longer FR.D., DVD Å .............TUNER: Switches to FREQUENCY
than 2 seconds. SAT only works with DIRECT.
digital satellite receivers. CD, CDR, VCR, DVD: Pauses playback.
1–0................................Keys in numbers for tracks, stations or INDEX, DVD T-C............VCR: Switches the index search on
frequencies. Numbers consisting of and off.
two figures must be keyed in within SAT: Switches the themes on and off.
2 seconds. DVD: Switches between title and
CINEMA LINK...............Switches the system connection chapter.
between the receiver and the TV on DISC..............................CD-, CDR-, DVD-Changers:
and off. Switches to the next disc.
CABLE BOX ...................Without function. NIGHT ...........................Switches NIGHT MODE on and off.
MENU GUIDE ..............TUNER: Switches the receiver menu 3D SURR.......................Switches virtual 3D surround on and off.
on and off.
SURR. ON/OFF..............Switches SURROUND SOUND on and off.
DVD, TV: Switches the DVD/TV menu
on and off. +/- SUBWOOFER...Increases/decreases the subwoofer
volume.
OK .................................Confirms menu options.
+/- REAR ...............Increases/decreases the volume of the
Arrow buttons ..............TUNER: Moves in the menus.
rear speakers. While test tone is on,
Right/left arrows are tuning up/down.
the volume of the speakers you are
CD, CDR: Left/right arrows are
hearing can be increased/decreased
searching backwards/forwards,
with these buttons.
up/down arrows are selecting the
next/previous track. SURR. MODE................Scrolls through the different surround
modes.
+A ...........................Increases the receiver volume.
TEST TONE ...................Switches the test tone on and off.
-A ...........................Decreases the receiver volume.
While test tone is on, the volume of
i NEWS/TA.................Switches the functions NEWS and the speakers you are hearing can be
TRAFFIC ANNOUNCEMENT on and off. increased/decreased with
TV: Switches teletext on and off. +/- REAR.
SAT: Switches the information text on
and off.
ÉATV ......................Increases the TV volume.
CD, CDR, VCR, DVD: Starts playback.
ÇATV ......................Decreases the TV volume.
CD, CDR, VCR, DVD: Stops playback.
í CHANNEL/TRACK ...Selects the previous preset tuner
station.
VCR: Rewinds the tape.
CD, CDR, DVD: Selects the previous
track.
TV: Selects the previous channel.
ë CHANNEL/TRACK ...Selects the next preset tuner station.
VCR: Fast forwards the tape.
CD, CDR, DVD: Selects the next track.
TV: Selects the next channel.
Once you have found and tested the codes for your various
Programming the universal remote control
English
• If the set does not react within 2 minutes, the code for this
appliance is not stored in the remote control. The code of
the remote control will remain unchanged.
Note: When taking out the batteries of the remote control for
more than 1 minute the codes must be reprogrammed.
)¡™£≤∞ §≥• ª º
English
LINK
CINEMA
LET 230V
~ 50 Hz
FRONT RS AC OUT STANDBY
POWER /
ANTENNA SPEAKE Ω
KER ≥ 6
EACH SPEA
FM 75 Ω
CINEMA
. LINK
ON
PHONO GND
AM LOO
P
CA U TI K
( DIGITAL
AUDIO
SUBWOO
FER
PRE-OUT R
L DO
ELECTR
IC SHOC
RISK OF NOT OPEN
DE CHO
CTRIQU
C ELE
E
*
PRE-OU
IN REC E , dem arks
OUT PLAY CDR/TAP Lab ora -3" are Tra poration.
IN ", "AC bol E
COAX 1 IN
UT
AUDIO IN/O SAT CD "DO LBY ing Cor FRONT
AV / GAM
e-D Sym Licenc
Doubl Laboratories
VCR
Dolby
&
TV
PHONO L
R≥6Ω
R
COAX 2 IN SPEAKE
L EACH
^ COAX OUT
R
IN
OUT
REC
IN
IN
IN
PLAY
OUT
REC
% PLAY
IN
IN
$#@!09876 5 43 2 1
Audio connections
English
ANTENNA
FM 75 Ω
PHONO GND.
AM LOOP
FRONT
SPEAKERS
DIGITAL
AUDIO CINEMA EACH SPEAKER ≥ 6 Ω
IN/OUT LINK
OPTICAL IN
VIDEO IN/OUT SUBWOOFER
DVD MON VCR SAT PRE-OUT
CENTER R L CAUTION
COAX 1 IN
IN OUT IN OUT IN RISK OF ELECTRIC SHOCK
PLAY REC
DO NOT OPEN
AUDIO IN/OUT CENTER
RISQUE DE CHOC ELECTRIQUE
COAX 2 IN PHONO TV VCR SAT CD CDR/TAPE PRE-OUT SURROUND
SPEAKERS
AVIS NE PAS OUVRIR
L
Designed and developed by Philips in the
European Community
COAX OUT
Manufactured under licence from Dolby
R Laboratories Licencing Corporation.
"DOLBY", "AC-3", "PRO-LOGIC" and the
R L Double-D Symbol are Trademarks of
IN IN IN OUT IN IN IN OUT Dolby Laboratories Licencing Corporation.
PLAY REC PLAY REC EACH SPEAKER ≥ 6 Ω
TURNTABLE
CD RECORDER
IN
OUT
VCR
AUDIO OUT
AUDIO IN CD PLAYER
SAT RECEIVER
DVD PLAYER
ANTENNA
FM 75 Ω
PHONO GND.
AM LOOP
FRONT
SPEAKERS
DIGITAL
AUDIO CINEMA EACH SPEAKER ≥ 6 Ω
IN/OUT LINK
CD PLAYER OPTICAL IN
VIDEO IN/OUT SUBWOOFER
DVD MON VCR SAT PRE-OUT
CENTER R L CAUTION
COAX 1 IN
IN OUT IN OUT IN RISK OF ELECTRIC SHOCK
PLAY REC
DO NOT OPEN
AUDIO IN/OUT CENTER
RISQUE DE CHOC ELECTRIQUE
COAX 2 IN PHONO TV VCR SAT CD CDR/TAPE PRE-OUT SURROUND
SPEAKERS
AVIS NE PAS OUVRIR
L
Designed and developed by Philips in the
European Community
COAX OUT
Manufactured under licence from Dolby
R Laboratories Licencing Corporation.
"DOLBY", "AC-3", "PRO-LOGIC" and the
R L Double-D Symbol are Trademarks of
IN IN IN OUT IN IN IN OUT Dolby Laboratories Licencing Corporation.
PLAY REC PLAY REC EACH SPEAKER ≥ 6 Ω
CD RECORDER
10
English
If the receiver and your Philips TV (or even better in addition
a Philips VCR or DVD player) are connected with the CINEMA
LINK system bus control, some extra system benefits are
offered:
– Upon starting a source the system will automatically
switch to that input.
TV
– You may control the system via the TV screen. Depending
EXT 1
on the language of the TV, this can be done in your
EXT 2 EXT 3
preferred language.
– The TV can function as the center speaker of your system,
making a separate center speaker unnecessary.
TV
DVD PLAYER
AUX
DIGITAL
OUT
– By pressing the standby button, you can switch the
complete Home Theater System to standby.
ANTENNA
FM 75 Ω
PHONO GND.
AM LOOP
FRONT
SPEAKERS
DIGITAL
VCR AUDIO
IN/OUT
CINEMA
LINK
EACH SPEAKER ≥ 6 Ω
OPTICAL IN
VIDEO IN/OUT SUBWOOFER
DVD MON VCR SAT PRE-OUT
CENTER R L CAUTION
COAX 1 IN
IN OUT IN OUT IN RISK OF ELECTRIC SHOCK
PLAY REC
DO NOT OPEN
AUDIO IN/OUT CENTER
RISQUE DE CHOC ELECTRIQUE
COAX 2 IN PHONO TV VCR SAT CD CDR/TAPE PRE-OUT SURROUND
SPEAKERS
AVIS NE PAS OUVRIR
L
Designed and developed by Philips in the
European Community
COAX OUT
Manufactured under licence from Dolby
R Laboratories Licencing Corporation.
"DOLBY", "AC-3", "PRO-LOGIC" and the
R L Double-D Symbol are Trademarks of
IN IN IN OUT IN IN IN OUT Dolby Laboratories Licencing Corporation.
PLAY REC PLAY REC EACH SPEAKER ≥ 6 Ω
CINEMA LINK
TO TV IN
TO VCR IN
Video connections
ANTENNA
FM 75 Ω
AM LOOP
FRONT
SPEAKERS
DIGITAL
AUDIO CINEMA EACH SPEAKER ≥ 6 Ω
IN/OUT LINK
OPTICAL IN
VIDEO IN/OUT SUBWOOFER
DVD MON VCR SAT PRE-OUT
CENTER R L CAUTION
COAX 1 IN
IN OUT IN OUT IN RISK OF ELECTRIC SHOCK
PLAY REC
DO NOT OPEN
AUDIO IN/OUT CENTER
RISQUE DE CHOC ELECTRIQUE
COAX 2 IN PHONO TV VCR SAT CD CDR/TAPE PRE-OUT SURROUND
SPEAKERS
AVIS NE PAS OUVRIR
L
Designed and developed by Philips in the
European Community
COAX OUT
Manufactured under licence from Dolby
R Laboratories Licencing Corporation.
"DOLBY", "AC-3", "PRO-LOGIC" and the
R L Double-D Symbol are Trademarks of
IN IN IN OUT IN IN IN OUT Dolby Laboratories Licencing Corporation.
PLAY REC PLAY REC EACH SPEAKER ≥ 6 Ω
VCR
VIDEO OUT
VIDEO IN
SAT RECEIVER
11
The type plate is located on the rear of the receiver. AM (MW) antenna
The loop antenna supplied is for indoor use only. Position the
1 Check whether the mains voltage as shown on the type antenna as far away as possible from the receiver, the TV, the
plate corresponds to your local mains voltage. If it does not, cables, a DVD player, a VCR and other radiation sources.
consult your dealer or service organization.
1 Fit the plug of the frame antenna to AM LOOP as shown
2 Connect the mains cable to the wall socket. below.
To disconnect the set from the mains completely, remove the 2 Turn the antenna for optimum reception.
mains plug from the wall socket.
A
For users in the U. K.: please follow the instructions on ANTENN
page 2.
2 Connect:
– Left front speaker to L (red and black)
– Right front speaker to R (red and black)
– Center speaker to CENTER (blue and black)
– Left surround speaker to SURROUND L (grey and black)
– Right surround speaker to SURROUND R (grey and black)
12
CENTER FR
NT ON Speaker setup and testing
English
FRO T
R The relative volume of the speakers must be adjusted for
FE
LEFT RIGHT optimal surround sound. You should be at your usual listening
OO
Positioning the front speakers To avoid overheating of the set a safety circuit has
The front speakers should be placed right and left in front of been built in. Therefore your set may disconnect under
the listening position like usual stereo speakers. extreme conditions. If this happens, switch the set off
and let it cool down before reusing it.
Positioning the center speaker
The center speaker should be placed in the center between Headphones
the two front speakers, e. g. underneath or on top of the TV.
The best height for the center speaker is the height of the Connecting headphones to PHONES will switch off the
listener’s ears (while seated). speakers. The receiver switches to STEREO and surround
sound will be reduced to a stereo signal which is reproducible
Positioning the surround speakers by standard headphones.
The surround speakers should face each other and be in line
with, or slightly behind the listener. Disconnecting the headphones switches on the speakers
again. If you wish to enjoy surround sound again, switch the
Positioning the subwoofer receiver back to surround sound.
A subwoofer can be used to enhance the bass performance of
your system dramatically. The subwoofer can be positioned
anywhere in the room, because it is not possible to locate the
source of deep tones. Nevertheless, you should not place the
subwoofer in the middle of a room, since the bass could be
severely weakened. Do not place any object on the
subwoofer.
13
Display 0
English
GUIDE
The display of the receiver is divided into 4 sections, which
MENU OK
are to be used for the following:
Speaker diagram
É
A rectangle with a letter in it shows that a speaker has been A ATV
selected in the setup menu. However, the subwoofer indicator
NEWS/TA Ç
will only light when a subwoofer signal is available. If only a
letter is shown, this speaker is not used and its sound is
reproduced by the other speakers.
.......virtual 3D surround
SURROUND.................surround sound is reproduced
DIGITAL SURROUND ....digital surround sound is reproduced
L, R ...........................front left and right speaker
C ...............................center speaker
SL, SR .......................surround speakers
SW ............................subwoofer
Menu indication
M E N U .......................menu is on
1..............................You may move backwards to the previous
menu topic using 1 PREV. / EXIT (“left”
key on the remote control).
3 .............................You may move up in an option list using
X MENU NAVIGATOR (“up” key on the
remote control).
4 .............................You may move down in an option list
using X MENU NAVIGATOR (“down” key
on the remote control).
2..............................You may move forward to the next menu
topic using NEXT 2 (“right” key on the
remote control).
O K.............................You may confirm the displayed value.
14
* SPEAKR SIZES
Receiver menu
English
Chooses the speaker sizes of the used speakers, for
The receiver is equipped with a menu system. The menu is optimal sound reproduction. LARGE indicates a speaker
used for the setup of the receiver. The different menu options which can reproduce frequencies lower than 50 Hz. If
are related to each other in a logical way. Let’s assume you SUBW PRESENT is set to NO, FRONT SIZE can only
have no center speaker connected, and therefore switched be set to LARGE. If FRONT SIZE is set to SMALL,
CENTER SPEAKR to NO. If you try to use VOL CENTER, CENTER SIZE can only be set to SMALL and
a message will be scrolled that this is not possible consequently a subwoofer must be connected.
(INSTALL CENTER SPEAKER). SUBW PRESENT
Subwoofer present: yes/no
The menu always works the same way. Arrows in the display FRONT SIZE
show you the possible moving directions. Left and right front speakers: small/large
CENTER SIZE
1 Press SETUP MENU. Center speaker: small/large
y MENU, and * EFFECTS is displayed. REAR SIZE
Rear speakers: small/large
• You can exit the menu at any time by pressing
* SPK DISTANCE
SETUP MENU.
Distance between the usual listening position and the
speakers. This defines the delay time for the surround sound.
2 Turn X MENU NAVIGATOR until the desired option (or a
DISTANCE L/ R
value) is displayed.
Distance to front speakers: 1…10 m
DISTANCE CNTR
3 Press NEXT 2 to choose the displayed option (or
Distance to center speaker: 1…10 m
ENTER / OK to confirm a value).
DISTANCE REAR
Distance to rear speakers: 1…10 m
• You can leave any option (values remain unchanged) by
pressing 1 PREV. / EXIT. * SELECT INPUT
Assigns the audio input connectors to the different source
Menu structure selections chosen with SOURCE SELECTOR (see “SOURCE
SELECTION” for details).
* EFFECTS
COAX1
Switches sound effects.
Digital coaxial input 1, COAX 1 IN
3D SURR
COAX2
virtual 3D surround: 0…100 %
Digital coaxial input 2, COAX 2 IN
* VOL BALANCE OPT
Adjusts the relative volume balance between the Digital optical input, OPTICAL IN
connected speakers. SAT IN
TEST TONE Analogue audio input SAT IN
Test tone: on/off VCR IN
VOL FRONT-L Analogue audio input VCR IN
Volume front left speaker: –50…+50 TV IN
VOL FRONT-R Analogue audio input TV IN
Volume front right speaker: –50…+50 CDR IN
VOL CENTER Analogue audio input CDR IN
Volume center speaker: –50…+50 CD IN
VOL REAR-L Analogue audio input CD IN
Volume rear left speaker: –50…+50
* TUNER
VOL REAR-R
Setup for preset radio stations (see “TUNER” for details).
Volume rear right speaker: –50…+50
AUTO INSTALL
VOL SUBWOOFER
Stores radio stations automatically
Volume subwoofer: –50…+50
MAN INSTALL
* SPEAKR SETUP Stores radio stations manually
Selects the used speakers. GIVE NAME
SUBW PRESENT Allows to assign names to stored radio stations
Subwoofer present: yes/no RESHUFFLE
CENTER SPEAKR Resorts stored radio stations
Center speaker present: yes/no
REAR SPEAKER
Rear speakers present: yes/no
15
TV menu
English
16
English
When selecting a source by turning SOURCE SELECTOR, the appliances
audio and video inputs with the corresponding name are You may assign more than one source to a source selection.
activated. The incoming signal is reproduced by all audio and This can be useful when products are connected one after the
– if the source includes a video signal – video outputs of the other in a chain.
receiver. It is possible to reassign a source selection to other
than these standard inputs. Example: A VCR is connected to the TV but only the TV is
connected to the receiver. Both SOURCE SELECTOR
Source selected........Connectors used settings, TV as well as VCR, have to use the TV
DVD...............................COAX 1 digital audio input and input connectors.
DVD IN video input
PHONO..........................PHONO IN audio input 1 Choose * SELECT INPUT from the menu and press
NEXT 2.
TUNER ..........................The tuner part of the receiver is used,
all inputs are switched off.
2 Turn SOURCE SELECTOR to select the source which should
CD .................................CD IN audio input be reassigned (e. g. VCR).
CDR/TAPE .....................CDR/TAPE IN audio input y The name of the source is displayed and the light of the
Reassigning a source selection 5 This source selection is now using the chosen audio input (e. g.
VCR uses the TV IN input connectors, VCR <TV IN> is
If a source is selected with SOURCE SELECTOR the standard
displayed briefly when switching to VCR).
audio input is used. To change this, the source selection must
be reassigned to another audio input.
17
1 Press POWER / STANDBY to switch on the receiver. If you wish to record from a source you must select it with
SOURCE SELECTOR. The incoming signal is reproduced by all
2 Turn SOURCE SELECTOR to select a source. audio and – if the source includes a video signal – video
y The name of the source is displayed. outputs of the receiver. The sound settings do not affect the
recording.
• You can select the FRONT AV / GAME input by pressing
FRONT AV (FR 970 only). 1 Turn SOURCE SELECTOR (or press FRONT AV – FR 970 only)
to select the source you want to record from.
3 Start playback of the source as usual. y The name of the source is displayed.
18
English
Surround sound gives you a complete new listening HALL
sensation. You will have the feeling of being in the middle of The sound reproduction is enhanced and a slight echo is
the action, because sound is coming from everywhere around added. This gives the impression of being in a large room.
you. Look out for TV broadcasts, audio and video tapes and Can only be used in stereo mode.
discs with the 3 1 or
marks which are encoded for multichannel surround sound. SURROUND
You should prefer Dolby Digital or MPEG Multichannel to get The surround mode enables normal surround sound reproduction
the best out of your receiver. with 4 or 5 speakers. Depending on the source material, Dolby
Surround Pro Logic, Dolby Digital or MPEG is reproduced.
Notice that DVDs do not always carry full multichannel
surround. To be sure that a disc is multichannel encoded PRO LOGIC, DOLBY DIGITAL, MPEG
consult your dealer. In addition to SURROUND, the surround mode used –
depending on the source material – will be displayed. In case
Most ordinary stereo tapes and discs can be replayed using of digital surround, the sound format AC-3 (for Dolby Digital) or
surround sound settings with good results. If the reproduction MPEG (for MPEG 2 Multichannel) will be displayed, followed by
is distorted in surround mode, switch to normal stereo mode. the sound channels, available on the source (e. g. DVD).
Example: AC-3 3/2.1 Dolby Digital, 3 front channels,
The availabilty of the various surround sound modes
2 surround channels and a subwoofer
described depends on the number of speakers used and the
channel.
incoming sound information.
MPEG 2/0.0 MPEG Multichannel, stereo sound only.
AC-3 3/1.0 Dolby Digital, 3 front channels, 1
Switching surround sound (mono) surround channel without
With surround sound on, you can switch through the different subwoofer signal.
surround modes. Note that the possibilities are related to
speaker setup defined in the receivers menu. FRONT-3 STEREO
The surround sound is muted. 3 Stereo lets you listen to
If a digital surround signal is detected, the receiver will scroll surround sound without using the surround speakers.
either DOLBY DIGITAL or MPEG.
3D SURROUND
1 Press SURROUND ON/OFF to switch on the surround sound. The sound of the rear channel is simulated by the front
y The surround mode in use is scrolled. speakers. Surround sound is simulated through the front left,
right and center speakers. The position of the listener
2 Press SURR. MODE repeatedly to listen to the different influences the surround effect. The area where the effect is
surround modes (if available). best is shown in grey.
yThe chosen mode and the speakers used are displayed.
If the incoming multichannel signals are reduced to CENTER FR
NT ON
fewer output signals, DOWNMIX is displayed. FRO T
STEREO
All sound is reproduced and played through the front left and
right speakers. This enables standard stereo reproduction.
19
You can search for radio stations by scanning the frequency You may store up to 30 radio stations in the memory. The
band. You can also key in the frequency of a known radio receiver can select and program radio stations by itself or you
station. If an FM station is being broadcast and received in can choose them yourself.
stereo, STEREO is shown.
Automatic programming
Searching for radio stations 1 Choose * TUNER from the menu and press NEXT 2.
1 Turn SOURCE SELECTOR to select the tuner.
y TUNER is displayed. 2 Choose AUTO INSTALL and press NEXT 2.
y The preset number where programming will start, the
2 Select a waveband by pressing TUNER AM/FM repeatedly. waveband and AUTO are displayed.
y The selected waveband is displayed.
3 Turn TUNER PRESET X to change the preset number where
3 Keep 1 or 2 pressed for approximately 1 second. programming should start.
y SEARCH is displayed and the tuner tunes to a station
with sufficient strength. 4 Use TUNER AM/FM to switch to the desired waveband.
4 Repeat this procedure until you find the desired station. 5 Press ENTER / OK to start programming.
y AUTO INSTALL flashes and all available radio
• To fine tune to a weak transmitter, briefly press 1 or 2 as stations are programmed, this may take a few minutes.
often as necessary for optimum reception. Programming is done when AUTO INSTALL stops
flashing.
Tuning to a radio station by frequency (with the remote
control only) Manual programming
1 Press TUNER. 1 Choose * TUNER from the menu and press NEXT 2.
y TUNER is displayed.
2 Choose MAN INSTALL and press NEXT 2.
2 Press FR. D.. y A preset number, the waveband and the frequency are
y _ is displayed. displayed.
3 Use 1–0 to key in the frequency of a radio station. 3 Turn TUNER PRESET X to change to the preset number
where the radio station should be stored.
Note: Only valid numbers within the frequency range of the
tuner can be keyed in. 4 Tune to the desired radio station (see “Searching for radio
stations”).
Switching FM sensitivity
5 Press ENTER / OK to confirm your selection.
You can switch the tuner to a lower search sensitivity, to
y STORED is displayed briefly. The radio station is
search only for stations with a strong signal (FM only).
programmed at the chosen preset number.
1 Turn SOURCE SELECTOR to select the tuner.
6 Select and store all desired radio stations this way.
y TUNER is displayed.
20
English
1 Turn SOURCE SELECTOR to TUNER to select the tuner. It is possible to assign a name to any of the preset radio
y TUNER is displayed. stations. RDS station names also can be overwritten.
2 Turn TUNER PRESET X to select a preset radio station. 1 Choose * TUNER from the menu and press NEXT 2.
y PRESET, the preset number and station are displayed.
2 Choose GIVE NAME and press NEXT 2.
Resorting stored radio stations y A preset radio station is displayed.
21
RDS R Receiver
English
Radio Data System is a service that allows FM stations to Subject to modification without notice.
send additional information. If you are receiving an RDS General
station, R and the station name are displayed. Power consumption (FR 960)........................................≈ 170 W
Power consumption (FR 970)........................................≈ 195 W
Switching through different RDS information Standby power consumption ............................................< 2 W
• Press RADIO TEXT on the receiver repeatedly to switch Dimensions, w × h × d ............................435 × 135 × 350 mm
through the following information (if available): Weight (FR 960) ................................................................8.6 kg
– Radio text messages Weight (FR 970) ................................................................9.4 kg
– RDS clock Amplifier part (0.7 % THD, 6 Ω, 1 kHz)
– Frequency Output power, stereo mode (FR 960) (DIN).................2 × 50 W
– Station name Output power, surround mode (FR 960)
Front ......................................................................2 × 50 W
Note: The time signal broadcasted from certain RDS stations Center ..........................................................................50 W
may not always be accurate. Surround................................................................2 × 50 W
Output power, stereo mode (FR 970) (DIN)...............2 × 100 W
RDS News and Traffic Announcement Output power, surround mode (FR 970)
Front ....................................................................2 × 100 W
It is possible to set up the tuner in such a way that any Center ........................................................................100 W
playback is interrupted by news or traffic information of a Surround................................................................2 × 50 W
chosen RDS station. Announcement functions only work if the Bass ..................................................................±9 dB at 100 Hz
necessary RDS signals are being broadcast. Treble ................................................................±9 dB at 10 kHz
Loudness ....+6 dB at 100 Hz (-30 dB); +3 dB at 10 kHz (-30 dB)
If RDS stations are also carrying an EON signal (Enhanced Total harmonic distortion.........................0.05 % at 1 kHz, 1 W
Other Networks), EON is displayed. This signal enables the Frequency response ..................................20–30,000 Hz, ±1 dB
tuner to search not only the chosen RDS station, but the S/N ratio ........................................................................≥ 82 dB
whole EON station network for news and traffic information. Stereo separation (1 kHz) ..............................................≥ 45 dB
Crosstalk (1 kHz) ...........................................................≤ -65 dB
1 Tune to the desired RDS station. Digital sampling frequency.................32 kHz, 44.1 kHz, 48 kHz
Inputs
2 Press NEWS/TA: Linear inputs ...................................................250 mV at 47 kΩ
Once to display NEWS, this switches on the news Front AV (FR 970 only) ....................................250 mV at 22 kΩ
announcement function. Phono ..................................................................5 mV at 47 kΩ
Twice to display TA, this switches on the traffic Digital coaxial ..............................................75 Ω acc. IEC 958
announcement function. Outputs
Three times to display TA and NEWS, this switches on both Power supply AC outlets (switched) ...........totally max. 100 W
announcement functions. Linear outputs...................................................250 mV at 1 kΩ
Digital coaxial ..............................................75 Ω acc. IEC 958
3 Select and play any other source as usual. Digital optical ..................................................................Toslink
y While news or traffic information is being broadcast Subwoofer pre-out................................................0.8 V at 1 kΩ
the receiver will switch to tuner and NEWS or TA will Center pre-out.......................................................0.8 V at 1 kΩ
flash. Headphones....................................8–600 Ω (3 V e.m.f., 60 Ω)
Speakers ...........................................................................≥ 6 Ω
4 Press NEWS/TA until the display indication disappears to Tuner part
switch off the function(s). Wave range
or FM..............................................................87.5–108.0 MHz
Press NEWS/TA during an announcement to switch off the MW...............................................................531–1,602 kHz
function(s). LW....................................................................153–279 kHz
Sensitivity
Note: Be sure to switch the news and traffic announcement Stereo FM ..................................................................41 dBf
off during recording, otherwise these announcements Mono FM....................................................................15 dBf
also will be recorded. Total harmonic distortion
Stereo FM ...................................................................0.3 %
Mono FM...................................................................0.85 %
Frequency response ...................................63–12,500 Hz ±1 dB
S/N ratio
Stereo FM....................................................................55 dB
Mono FM.....................................................................60 dB
Channel separation .............................................35 dB at 1 kHz
22
English
WARNING If a fault occurs, first check the points listed, before taking
the set for repair.
Under no circumstances should you try to repair the
set yourself as this will invalidate the guarantee. Do If you are unable to solve a problem by following these hints,
not open the set as there is a risk of electric shock. consult your dealer or service centre.
23
http://www. philips.com
Français
Español
Deutsch
Nederlands
Italiano
FR960
3104 215 3604.3 FR970 VieUrs9942