Professional Documents
Culture Documents
Materials System Specification
Materials System Specification
1 Scope............................................................. 2
2 Conflicts and Deviations................................. 2
3 References..................................................... 2
4 General........................................................... 3
5 Materials......................................................... 3
6 Inspection and Testing................................... 5
7 Documentation............................................... 5
8 Product Marking............................................. 5
9 Export Packing, Marking and Shipping.......... 5
10 Material Selection and
Testing Subcommittee............................ 6
1 Scope
1.1 This specification prescribes the requirements that apply to carbon steel and low
alloy steel piping components for use in services with design minimum
temperatures within the range of -18°C to -45°C.
1.2 Components included are butt welding pipe fittings such as elbows, tees,
welding outlets, reducers, caps, and lap joint stub ends < NPS 24, as well as
blind flanges, spectacle plates, spacers and slip blinds. Pipe is not included as a
piping component and is not addressed in this specification.
1.3 This specification is intended to apply to purchase of "loose" components and is
not mandatory for components installed on equipment that is engineered,
manufactured, and tested prior to delivery to Saudi Aramco.
1.4 Socket-welding and threaded fittings less than 2-inch NPS are excluded from
this specification.
2 Conflicts And Deviations
2.1 Any conflicts between this specification and other applicable Saudi Aramco
Materials System Specifications (SAMSSs), Engineering Standards (SAESs),
Standard Drawings (SASDs), or industry standards, codes, and forms shall be
resolved in writing by the Company or Buyer Representative through the
Manager, Consulting Services Department of Saudi Aramco, Dhahran.
2.2 Direct all requests to deviate from this specification in writing to the Company
or Buyer Representative, who shall follow internal company procedure SAEP-
302 and forward such requests to the Manager, Consulting Services Department
of Saudi Aramco, Dhahran.
3 References
The design of the piping components shall be in accordance with the following
standards, Saudi Aramco Specifications and Standard Drawings.
3.1 Saudi Aramco References
Saudi Aramco Engineering Procedure
SAEP-302 Instructions for Obtaining a Waiver of a
Mandatory Saudi Aramco Engineering
Requirement
Saudi Aramco Engineering Standard
SAES-A-301 Materials Resistant to Sulfide Stress Corrosion
Cracking
Saudi Aramco Materials System Specification
02-SAMSS-005 Butt Welding Pipe Fittings
Page 2 of 6
Document Responsibility: Materials and Corrosion Control 02-SAMSS-001
Issue Date: 29 June 2005
Next Planned Update: 1 July 2010 Piping Components for Low Temperature Service
Page 3 of 6
Document Responsibility: Materials and Corrosion Control 02-SAMSS-001
Issue Date: 29 June 2005
Next Planned Update: 1 July 2010 Piping Components for Low Temperature Service
In the notation of required Charpy Values such as 25/20, the first number
is the average energy of three specimens while the second number is the
minimum for any one specimen.
The provisions in ASTM A350 Para. 7.2.4 for subsize specimens and test
temperature reduction are the same as in ASME B31.3 Para. 323.3.
5.2.3 Grade LF2 materials shall be tested as specified in ASTM A350 except
that the required Charpy V-notch impact values shall be 34/27 J (25/20
ft-lbs) for standard 10 mm by 10 mm specimens.
5.2.4 ASTM A516 plate, used for blind flanges, spectacle plates, blinds, and
spacers, shall be tested as specified in ASTM A516 S2, S5, S12 and the
required longitudinal Charpy V-notch impact values shall be 34/27 J
(25/20 ft-lbs) for standard 10 mm by 10 mm specimens. For subsize
specimens the provisions of ASME B31.3 Para. 323.3 shall apply.
5.3 Butt welding pipe fittings shall also comply with 02-SAMSS-005.
5.4 Piping components shall comply with the requirements of SAES-A-301 when
specified in the Purchase Order.
Commentary Note:
SAES-A-301 is not normally specified for butt-welding pipe fittings per 02-
SAMSS-005 because 02-SAMSS-005 requirements are consistent with
SAES-A-301 and are considered by Saudi Aramco to be adequate for sour
service.
Page 4 of 6
Document Responsibility: Materials and Corrosion Control 02-SAMSS-001
Issue Date: 29 June 2005
Next Planned Update: 1 July 2010 Piping Components for Low Temperature Service
Page 5 of 6
Document Responsibility: Materials and Corrosion Control 02-SAMSS-001
Issue Date: 29 June 2005
Next Planned Update: 1 July 2010 Piping Components for Low Temperature Service
Revision Summary
29 June 2005 Revised the "Next Planned Update". Reaffirmed the contents of the document, and reissued
with editorial changes.
Page 6 of 6