FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite"
2060CDS/2100Series
BATTERY PACK REMOVAL OPTIONAL PCMCIA CARD REMOVAL
Battery release
lever
PC card Eject button
1, Turn the computer upside down as shown,
2. Slide the battery release lever inthe direction of the
arrow.
3. Pull the battery pack slightly forward and lift
it out
1. Pull out the ejeet button of the PC eardto be remaved.
2. Press the eject button and remove the PC card.
KEYBOARD REMOVAL m8 Latch KEYBOARD REMOVAL
Keyboard métal brace 2x4 brass screw
Keyboard holder
1. Open the display panel 3. Remove one M2xd brass serew and lift out the
2. Remove the Keyboard holder at the base ofthe keyboard metal brace,
TOSHIBA
Tough Enough for Todays World.FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite"
2060CDS/2100Series
KEYBOARD REMOVAL
Keyboard top
cover
Punt
Keyboard cable
Keyboard
M2504 black screw
4 Lift out the keyboard and lay it on the palm rest cover
Be careful not to apply pressure on the keyboard eable,
5, Remove one NB.Sx6 black screw and lift out the
keyboard top cover between the speakers.
6, Disconnect the keyboard cable fom P41 on the
system board and remavethe keyboard,
HDD REMOVAL
M2Sx6black
screw
HDD slot cover
4. Tum the computer upside down,
2. Remove one M2.5x6 black screw securing HDD
slot cover and pull out the cover
EXPANSION MEMORY REMOVAL
M23 black
screvs
Memory
cover
Memory
module
Memory dips
4. Tum the computer upside down.
2. Remave two M2x3 black eerewe and remove the
memory cover.
3. Pushthe memory clips outvard and pull the memory
Module out ofthe connector on a 45 degree angle.
HDD
M2.Sxa
black
screw
HDD bracket handle
3. Remove oneM2.5x4 black screw securing the HDD
4. Grasp the HDD braeket handle and pul ta disconnect
the HDD.
TOSHIBA
Tough Enough for Todays World.FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite’
2060CDS/2100Series
MODEM REMOVAL TOP COVER REMOVAL
M2.5x6 black serene
Modem board
Modem cable M2:Gsilverscrems — M2xS brass screw
1. Remove twoMEx3 ser screws snd oneMDxs brass
serewsecuring the modem board lack screw a Sa back
2.Lift up the right side of the modem board arci remove it pe seh rene
ffom the system board 1. Tum the computer upside down and remove the
3. Disconnect the modem cable from PJ2 on the modem board. folowing thirteen screws
-4NB.5x20 black screws
-3 M2.Sx6 black serews (one fromHDD slot covery
TOP COVER REMOVAL. "5 Wet black serene ror battery sit and back
M2.5x20 black screws Pua LED cable of the computer
-1 M2x16 black screw
PAM
Rightet
speaker cable Top cover
tone _— Volume
P30 connrol
M2Sx4 black Membrane Puio
screw switch cable
2. Tum the computer right side up and open the
sdigplay panel
3, Remove two M2.5x20 black screws ancl Display assembly
‘one NB.5x4 black screw securing the top cover:
4, Disconnect the following tve cables: 5. Lift upthe back and left-side of the top cover about
-LED cable fromPJ4 1 emto release the left latch on the ffont (arrow and 2)
=FL cable fromP.J5 Push the tight (arrow) to dear the volume control
= Membrane ewiteh eable from P.J10 ‘fom the top cover.
Left speaker cable from P.J303 6. Rotate the top cover ancl display assembly forwarcd
- Right speaker cable fromPJ304 to release the right latch
TOSHIBA
Tough Enough for Todays Word.FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite”
2060CDS/2100Series
HDD AND BATTERY BOARD REMOVAL FDD REMOVAL
Battery power
line cable
2.838 brass
sew, M2.5x5
PuTs3 hex stud
M254
brass
scew
HDDubattery board = PU754 “Sensor cable
1. Disconned the following cables ftom the 1. Disconnect the FDD flexible cable fom PJ15 onthe
HOD Mbattery board: system board
-HDD cable from PJ750 2. Remove one MB.5x4 brass screw and one M2.5x5,
Battery power line cable from P.JT53 hhex stud securing the FDD and lit the FDD out.
“Sensor cable from PJT54 3, Remove four M2.5x3 brass strews securing the FDD
2. Remove one M2.5x6 brass screw. tothe FDD case
3.Lift up the HDD Mhattery board 4, Disconnect the FDD flexible cable fom the FDD
CD-ROM DRIVE REMOVAL
Side brace
2x6 brass,
= 11298 silver
scene
flexible cable
Connector
brace : CD-ROM
exible
CD-ROM 4
Pu301 M25xd brass screw connector Pen: cable
1. Disconnect the CD-ROM flexible cable fiom P3014 on 4, Remove two M2x6 brass screws securing the
the system board CD-ROM connector assembly.
2, Remove oneN®.Sx4 brass screwsecuring the CD-ROM 5. Separate the CD-ROM connector andthe connector
drive brace from the CD-ROM drive
3, Slide ou the CD-ROM drive: 6. Disconnect the CD-ROM flexible cable fom PJ760
onthe CD-ROM comnector.
Remove two M2x3 gerewe securing the side brace,
TOSHIBA
Tough Enough for Todays World.FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite”
2060CDS/2100Series
RTC AND BACKUP BATTERY REMOVAL
RTC battery
Paroo
Puro
1. Open the RTC battery cover.
2. Disconnect the RTC battery cable ftom PJT02 on the
sound board,
3.Lift out the RTC battery.
SYSTEM BOARD REMOVAL
M2.5x4 brass screws M2.Sx6 brass screw
M2.5x4 brass
sores
Heat sink duct
Heat sink holder
Insulator
P2.Sx4 fat
head screws
Pu7o0
Heat sink Plastic stud Sound cable
1, Remove plastic stud anc! insulator.
2. Disconned the sound cable fiom PJT00 on the sound board
3, Remove the following seven eerewe securing the
heat sink, system board and PC card slot cover
- 2 M2.5x4 flat head brass screws.
- 3 NB.5x4 brass screws:
- 3 NB.5x6 brass screw
Lift ouf the heat sink duet and remove the eat eink by
unlatching the heat sink holder fiom the tab ofthe CPU socket
RTC battery cable
SENSOR AND SOUND BOARD REMOVAL
M2.Sx4 brass screw
1. Disconnect the sound cable from P.J700 on the
‘sound board
2, Remove one M2.5x4 brass screw securing the
sound board
3. Lift up the eound board,
PC card
ot cover System board Ba
cable
5. Lift out the system board fom the front end and
remove the PC card slot cover
6. Disconnectthe following cables from the system board:
- HDD battery cable fromPJ300
- Battery power cable from P1501
- Sound cable from P4302
TOSHIBA
Tough Enough for Todays World.FIELD KEPLACEABLE UNIT DOCUMENTATION
Satellite”
2060CDS/2100Series
SPEAKERS REMOVAL
M24 brass
screws
Membrane
switch
M2xd fat head screws
‘1, Remove two MRx4 brass screws securing the 1. Remove two MB flat head serews securing
membrane switch each speaker.
2. Lift up the membrane switeh 2. Remove the tape securing the speaker cables
and lt out the speakers.
COOLING FAN REMOVAL
MM2x4 flat head
silver screws
Cooling fan
1 Remove the tape covering PJ and the fan cable.
2. Disconnect thefan cable Tom PJ on the system beard,
3. Remove two M2.4 silver screws securing the cooling fan.
4. Take out the eooling fan from the system board
TOSHIBA
Tough Enough for Todays World.FIELD REPLACEABLE UNIT DOCUMENTATION
Satellite”
2060CDS/2100Series
DISPLAY MASK FL INVERTER AND SCREEN REMOVAL
Display M2.5x6
Masi Seals
LOD cable LOD module FL inverter cable
1 Remove two mask seals at the bottom corners of the 1, Remove two MB.Sx6 brass screw securing
display assembly. FL inverter board
2. Remove two M2.5x6 brass screws. 2. Carefully rotate the FLL inverter board out from right
3. Thete ate 22 latehes securing the display mask to left then disconnect the FL inwester cable trom
Carefuly insert your fngers between the display mask and 1 andthe HV cable from CN2
the LED module and pry openthe latches starting from the 3. Remove four N@.5x6 brass screws securing the
‘top six latches, to the five latches on the right LCD module.
and left sides, ending wth the six bottomlatches. 4, Carefully rotate the LCD module fom right to left
ofthe LCD cover.
§. Disconnect the LCD eable from the LCD module and
remove the LED from the computer
TOSHIBA
Tough Enough for Todays World.