Professional Documents
Culture Documents
Operating Manual: Universal Control For DMS Transmitter
Operating Manual: Universal Control For DMS Transmitter
DMS transmitter
MEAG-DMST
MEAG-DMST-66698-7-1-1506-
en-US
Table of contents
1 Important information 5
1.1 Availability of the instructions ....................................................................... 5
1.2 Applicable documents ................................................................................... 5
1.3 Contact .......................................................................................................... 5
1.3.1 Feedback regarding this manual .................................................. 5
1.4 Personnel qualifications ................................................................................ 5
1.4.1 Electrician ...................................................................................... 5
2 Safety 6
2.1 Intended use ................................................................................................. 6
2.2 Technical state .............................................................................................. 6
2.3 ATEX designation ......................................................................................... 6
2.4 Personnel qualifications ................................................................................ 6
2.5 Installation ..................................................................................................... 7
2.6 Earthing ......................................................................................................... 7
3 Technical data 8
3.1 Housing ......................................................................................................... 8
3.2 Ambient conditions ........................................................................................ 8
3.3 Electrical data ................................................................................................ 8
3.4 Force transducer (DMS/LC) .......................................................................... 9
3.5 Interfaces ....................................................................................................... 9
3.6 Miscellaneous ................................................................................................ 9
3.7 Design versions ............................................................................................. 9
4 Description 10
4.1 Nameplate ..................................................................................................... 10
4.2 Operating principle ........................................................................................ 10
4.3 Operating mode ............................................................................................ 10
5 Connection 11
5.1 Circuit board EBD 1312 ................................................................................ 11
5.2 Jumpers EBD 1312 ....................................................................................... 12
5.3 Connection for power supply ........................................................................ 12
5.4 RS-485 SIO_0 interface ................................................................................ 13
5.5 RS-485 SIO_1 interface ................................................................................ 13
5.6 Profibus DP or RS-485 SIO_2 ..................................................................... 14
5.7 CAN interface ................................................................................................ 14
5.8 24 V inputs .................................................................................................... 15
5.9 24 V outputs .................................................................................................. 16
5.10 0 … 5 V or 0/4 … 20 mA analog inputs ..................................................... 18
5.11 0/4 … 20 mA analog outputs ....................................................................... 19
6 Operation 20
6.1 Display operating elements .......................................................................... 20
6.2 Parameters and parameter groups .............................................................. 21
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
2 Table of contents
7 Configuration 23
7.1 Setting the application .................................................................................. 23
7.2 Device-specific settings ................................................................................. 23
7.3 Using the input wizard .................................................................................. 24
7.4 Scale calibration ............................................................................................ 24
7.5 Restoring factory settings ............................................................................. 25
8 Parameters 26
8.1 Notes for the parameter details ................................................................... 26
8.2 Application parameters ................................................................................. 26
8.2.1 USER (operating parameters) parameter group .......................... 26
8.2.2 MAIN (main parameters) parameter group .................................. 27
8.2.3 TCON (configuration parameters) parameter group .................... 28
8.3 Basic parameters .......................................................................................... 30
8.3.1 SYS (system configuration) parameter group .............................. 30
8.3.2 ADC (Analog/Digital Converter) parameter group ....................... 36
8.3.3 HOST (SIO_1/SIO_2 serial interface) parameter group .............. 40
8.3.4 ENET (Ethernet) parameter group ............................................... 42
8.3.5 TCP (Ethernet TCP/IP) parameter group ..................................... 45
8.3.6 PBDP (Profibus DP) parameter group ......................................... 47
8.3.7 SERV (service information) parameter group .............................. 50
10 Spare parts 66
10.1 Basic versions ............................................................................................... 66
10.2 Options .......................................................................................................... 66
10.3 Spare parts in stock ...................................................................................... 67
10.4 Spare parts lists ............................................................................................ 67
11 Appendix 69
11.1 Force transducer connections ...................................................................... 69
11.1.1 Force transducer types and wire colors ....................................... 69
11.1.2 4-wire force transducer ................................................................. 69
11.1.3 6-wire force transducer ................................................................. 69
11.2 DMS terminal box ......................................................................................... 70
11.2.1 Dimensions and technical specifications for terminal box
VKK1-4 .......................................................................................... 70
11.2.2 Dimensions and technical specifications for terminal box
VKK2-8 .......................................................................................... 70
11.2.3 4-wire force transducer with connection box ............................... 71
11.2.4 6-wire force transducer with connection box ............................... 71
11.3 LC module ..................................................................................................... 71
11.3.1 Dimensions and technical specifications ...................................... 71
11.3.2 4-wire force transducer with LC module ...................................... 72
11.3.3 6-wire force transducer with LC module ...................................... 72
11.4 CAN expansion modules .............................................................................. 73
11.4.1 Types ............................................................................................. 73
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Table of contents 3
11.4.2 Connection ..................................................................................... 73
11.4.3 LED display ................................................................................... 73
11.5 Remote control .............................................................................................. 75
11.5.1 Installation version ......................................................................... 75
11.5.2 Table or wall version ..................................................................... 76
11.5.3 Connect to MEAG circuit board SIO_0 ........................................ 76
11.6 EU declaration of conformity ........................................................................ 78
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
4 Table of contents
1 Important information
► Retain the instructions and other applicable documents over the entire life-
time of the product and keep them at hand for reference.
► Pass on the instructions and other applicable documents to the next owner
or operator of the product.
The documents are written for programmers. The descriptions are therefore only
available on request and only in German or English.
1.3 Contact
► If you have any questions, please contact the nearest branch of Bühler
Group. See www.buhlergroup.com.
► Keep the instructions ready at hand.
► Keep the machine number ready to hand.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 1 Important information 5
2 Safety
► Only charge qualified personnel with tasks described in these operating in-
structions.
► The plant operator must ensure that personnel comply with local laws and
regulations for safe and hazard-conscious work.
► The plant operator must assign responsibilities and make these known. Pro-
vide keys and passwords only to assigned personnel.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
6 Chapter 2 Safety
2.5 Installation
1
Ensure degree of protection IP65 and seal integrity for ATEX zone 22:
2.6 Earthing
Earthing housing:
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 2 Safety 7
3 Technical data
3.1 Housing
Designation Value Unit
Height 300 mm
Width 380 mm
Depth 155 mm
Weight, approx. 10 kg
Degree of protection IP65
Power supply
24 V inputs (8)
24 V outputs (12)
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
8 Chapter 3 Technical data
Analog outputs 0/4 … 20 mA (2)
3.5 Interfaces
■ Profibus-DP: Profibus-Slave, 9-pin D-Sub socket
■ USB: USB device interface for service
■ CAN: CAN interface for expansion modules
■ RS-485: Serial HOST interface
3.6 Miscellaneous
■ Flash memory for program and data logger
■ Battery-powered RAM for parameters: Data protection for at least 20 years
■ Noise emission (emission): EN 50081-1 class B complied with
■ Noise immunity (immunity): EN 50082-2 industrial sector complied with
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 3 Technical data 9
4 Description
4.1 Nameplate
The control unit software can be configured for various applications. It is operat-
ed in the same way for all applications.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
10 Chapter 4 Description
5 Connection
X50
+24V 1
0V 2
PE 3
X1
X55
F1 26 25
Battery
USB
X80
X41 1 6
H1 2 5
3 4
X100 2 1
CAN
1
1
2
2
3
3
4
4 X51
S10_0
X30
X71 X70
B B B
A A A
OUT 0 … 3
H200
A-OUT
RUN CAL
1 1 1
H201 X81
2 2 2
1 6
S2
H202 2 5
3 3 3
3 4 X10 LC
H203
4 4 4
1
5 SIO_1 X31 5
2
6 X7
3
X40 X2 X62
1 1
H100 V V
4
Profibus H104
2 2 A A
H204 H208
5
H101 H105
1 1 3 3
H205 H209
6
2 2 4 4 1
7
H206 H210
3 3 5 5 2
X314
H207 H211 H102 H106
4 4 6 6 3 1 6
H103 H107 2 5
5 5 7 7 4 3 4
6 WIRE 1 6 6 WIRE
6 6 8 8 5 2 5
4 WIRE 4 WIRE
3 4
OUT 4 … 7 OUT 8 … 11 IN 0 … 3 IN 4 … 7 A - IN
X313
X3 X4 X5 X6 X8 EBD 1312
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 5 Connection 11
5.2 Jumpers EBD 1312
X80
1 6
2 5
3 4
X71 X70 X81
B B B 1 6 X314
2 5 X62
A A A 1 6
3 4 2
V V 5
A A 3 4
6 WIRE 1 6 6 WIRE
2 5
4 WIRE 3 4 4 WIRE
X313
EBD 1312
Fig. 5.2
L Phase
24 V DC
Terminal (yellow/green) PE
1 1 +24 V
2 2 0 V
3 3 PE
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
12 Chapter 5 Connection
5.4 RS-485 SIO_0 interface
The plug is reserved for (local or remote) control.
2 2 0 V
3 3 RXD TXD +
4 4 RXD TXD –
X Signal Description
X30:1 +24 V +24 V output voltage. Provides voltage for local
and/or remote control.
X30:2 0 V 0 V and shield connection
X30:3 RXD TXD + RS-485 SIO_0 positive signal
X30:4 RXD TXD – RS-485 SIO_0 negative signal
Connect bus terminating resistor to X80. All 3 jumpers are connected as stand-
ard.
2 2 0 V
3 3 RXD TXD +
4 4 RXD TXD –
X Signal Description
X31:1 +24 V +24 V output voltage. Do not use. Communication
takes place via X31:3 and X31:4.
X31:2 0 V 0 V and shield connection
X31:3 RXD TXD + RS-485 SIO_1 positive signal
X31:4 RXD TXD – RS-485 SIO_1 negative signal
■ If the control system is the last device on the bus, plug in middle jumper
X81:2–5.
■ If the HOST has no bias resistors, connect external jumpers X81:1‑6 and
X81:3‑4 to last device.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 5 Connection 13
5.6 Profibus DP or RS-485 SIO_2
Switching with the X70 (left and right) and X71 (left) jumpers between Profibus
DP and RS-485 SIO_2:
■ B = Profibus DP
■ A = RS-485 SIO_2
5
9
4
8
3
7
2
6
1
X Signal Description
X40:3 RS485_B Profibus-DP / RS-485 SIO_2, positive signal
X40:4 RTS Profibus DP norm
X40:5 0 V_EX Profibus DP norm
X40:6 +5 V_EX Profibus DP norm
X40:8 RS485_A Profibus-DP / RS-485 SIO_2, negative signal
2 2 0 V
3 3 CAN H
4 4 CAN L
X Signal Description
X100:1 +24 V +24 V output voltage. Supplies CAN module with
voltage.
X100:2 0 V 0 V and shield connection
X100:3 CAN H CAN positive signal
X100:4 CAN L CAN negative signal
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
14 Chapter 5 Connection
5.8 24 V inputs
X5/X6 Terminal Function Function
X5 X6
1 1 +24 V_IO +24 V_IO
2 2 DI_0.0 DI_0.4
3 3 DI_0.1 DI_0.5
4 4 GND GND
5 5 +24 V_IO +24 V_IO
6 6 DI_0.2 DI_0.6
7 7 DI_0.3 DI_0.7
8 8 GND GND
DI X Signal Description
0.0 X5:2 Zeroing 24 V pulse lasting at least 200 [ms].
Gross and net weight are set to 0.
0.1 X5:3 Zeroing ±4 % 24 V pulse lasting at least 200 [ms].
Gross and net weight are set to 0 if the cur-
rent scale weight is < 4 % of the maximum
scale weight ADC.MAXR or TCON.MAXW.
0.2 X5:6 Taring 24 V pulse lasting at least 200 [ms].
Net weight is set to 0.
Remote display (optional) switches to net
weight.
0.3 X5:7 Gross display 24 V pulse lasting at least 200 [ms] or sus-
tained signal.
Remote display (optional) switches to gross
weight.
0.4 X6:2 Net display 24 V pulse lasting at least 200 [ms] or sus-
tained signal.
Remote display (optional) switches to net
weight.
0.5 X6:3 Clear alarm 24 V pulse lasting at least 200 [ms].
Acknowledge alarm (see the chapter entitled
"Alarms").
0.6 X6:6
0.7 X6:7 Accept weight / 24 V pulse lasting at least 200 [ms].
Print The gross and net weight are saved in the job
memory with ID numbers. Device begins print-
ing the gross and net weight (optional).
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 5 Connection 15
5.9 24 V outputs
X2/X3/X4 Terminal Function Function Function
X2 X3 X4
1 1 D0_0.0 D0_0.4 D0_0.8
2 2 D0_0.1 D0_0.5 D0_0.9
3 3 D0_0.2 D0_0.6 D0_0.10
4 4 D0_0.3 D0_0.7 D0_0.11
5 5 GND GND GND
6 6 GND GND GND
DO X Signal Description
0.0 X2:1 Weight sign 24 V = Positive
0 V = Negative
0.1 X2:2 Scale standstill 24 V = Standstill
0 V = No standstill
0.2 X2:3 Operation SYS.AINV = OFF:
24 V = Alarm (alarm or control when in cali-
bration mode)
0 V = Operation
SYS.AINV = ON:
24 V = Operation
0 V = Alarm (alarm or control when in calibra-
tion mode)
0.3 X2:4 Data ready 24 V weight outputs are valid
0 V weight outputs are invalid
When changing the weight output bits, the
“Data Ready” signal is at 0 V. The signal
switches to 24 V after a delay TCON.TDRD.
0.4 X3:1 Weight bit 1 24 V = Logical “1”
0.5 X3:2 Weight bit 2 0 V = Logical “0”
The gross weight is sent to the digital outputs
0.6 X3:3 Weight bit 3
in binary format or in BCD format. (for configu-
0.7 X3:4 Weight bit 4 ration, see TCON.OFOR.) The significance of
0.8 X4:1 Weight bit 5 bit 1 (LSB) corresponds to the set division val-
ue TCON.DDIV.
0.9 X4:2 Weight bit 6
Example:
0.10 X4:3 Weight bit 7 Gross weight: = 915.7 kg
0.11 X4:4 Weight bit 8 TCON.DDIV: = 0.10 kg (significance of bit 1)
TCON.OFOR: = BIN20
Decimal value: = 9157
Binary value: = (MSB) 0000 0010 0011 1100
0101 (LSB)
Hex value: = 023C5 (023C5h)
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
16 Chapter 5 Connection
DO_0.6 = 24 V when current weight ≥ MAIN.NWT2
DO X Signal Description
1.0 X101:2 Weight bit 9 See weight bit 1 … 8
1.1 X101:3 Weight bit 10
1.2 X101:6 Weight bit 11
1.3 X101:7 Weight bit 12
1.4 X102:2 Weight bit 13
1.5 X102:3 Weight bit 14
1.6 X102:6 Weight bit 15
1.7 X102:7 Weight bit 16
1.8 X103:2 Weight bit 17
1.9 X103:3 Weight bit 18
1.10 X103:6 Weight bit 19
1.11 X103:7 Weight bit 20
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 5 Connection 17
X101/X102/X103 Terminal Function Function Function
X101 X102 X103
1 1 +24 V_IO +24 V_IO +24 V_IO
2 2 DO_2.0
3 3 DO_2.1
4 4 GND GND GND
5 5 +24 V_IO +24 V_IO +24 V_IO
6 6 DO_2.2
7 7 DO_2.3
8 8 GND GND GND
DO X Signal Description
2.0 X101:2 Weight bit 21 See weight bit 1 … 8
2.1 X101:3 Weight bit 22
2.2 X101:6 Weight bit 23
2.3 X101:7 Weight bit 24
AI X8 Signal Description
0.0 X8:1 + 0/4 … 20 mA
X8:2 - X62 on the
left = A
0 … 5 V
X62 on the
left = V
0.1 X8:3 + 0/4 … 20 mA
X8:4 - X62 on the
right = A
0 … 5 V
X62 on the
right = V
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
18 Chapter 5 Connection
5.11 0/4 … 20 mA analog outputs
X7 Terminal Function
1 1 + AO_0.0
2 2 GND
3 3 + AO_0.1
4 4 GND
5 5 GND
AO X7 Signal Description
0.0 X7:1 + 0/4 … 20 mA Gross weight analog.
X7:2 - 20 mA corresponds to the TCON.MAXW rate.
0.1 X7:3 + 0/4 … 20 mA
X7:4 -
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 5 Connection 19
6 Operation
H1 H2 H3 H4 H5 H6
lb
kg
S1 S2 S3 S4 S5 S6 S7 S8
H1 Remote control
H2 Not used
H3 Not used
H4 Not used
H5 Current scale weight is in the zero range.
H6 Scale standstill. See ADC.MOT.
H7 Weight unit (lb)
H8 Weight unit (kg)
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
20 Chapter 6 Operation
6.2 Parameters and parameter groups
Parameters in this document have the notation “Parametergroup.Parameter”, e.g.
SYS.TYP is the parameter TYP of the parameter group SYS. The decimal preci-
sion of the displayed weight values depends on the ADC.DIV parameter. Set the
weight unit at the ADC.UNIT parameter.
The following diagram shows the structure of the parameter groups. P1, P2 and
P3 represent the individual parameters.
USER
S5
S5
+ > 1s
S6
S5 S5 S5 S5 S5
… … … … … …
The control system is operated via the USER parameter group and subordinate
parameter groups such as MAIN, SYS etc.
The control system's display changes after 600 seconds by default without user
input to the first parameter of the USER parameter group.
Function Description
Invoke subordinate parameter
Press and for 1 second.
group.
Change to the next subordinate pa-
button.
rameter group.
Select parameters. + to the next parameter.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 6 Operation 21
Function Description
Save parameter value.
Press .
Invoke USER parameter group.
Press for 1 second.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
22 Chapter 6 Operation
7 Configuration
Prerequisites:
Important
The control system application is normally already set in the factory.
► Only carry out the following procedure if the application was reset or not
set.
► Set division.
► Set a meaningful division value at the ADC.DIV parameter appropriate to
the weight range used. If the device is not being used in an area that is
subject to calibration, the division value must be approximately 1/10,000
of the maximum weight, e.g. 0.01 kg for a 100-kg scale.
► Set Profibus-DP.
► If Profibus-DP is being used, set the desired protocol at the PBDP.MPDP
parameter and the address at PBDP.ADR.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 7 Configuration 23
7.3 Using the input wizard
Enter parameter values with the input wizard.
Important
This procedure is used to change important settings that have normally al-
ready been set in the factory.
► Only carry out this procedure if the most important parameters were not
configured in the factory or if the control system is to be reset.
Prerequisites
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
24 Chapter 7 Configuration
3. Calibrate scale:
► Select ADC.CALW parameter.
► Enter the total weight of the calibration weights. The calibration weight
should be 30...100 % of the load capacity.
► Fasten the calibrations weights symmetrically in the intended places.
► Press for 1 second.
→ A rotating clock symbol is displayed. Do not touch the scale during this
process.
CAUTION
All set values are overwritten.
► All parameters that differ from the factory setting must be reentered.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 7 Configuration 25
8 Parameters
Step Description
No information. Parameters can always be adjusted.
C Parameters can be adjusted when the calibration switch is set to CAL.
L Parameter can be adjusted if LOCK parameter = OFF.
Locked if LOCK parameter = LOW/MED/HIGH.
M Parameter can be adjusted if LOCK parameter = OFF/LOW.
Locked if LOCK parameter = MED/HIGH.
H Parameter can be adjusted if LOCK parameter = OFF/LOW/MED.
Locked if LOCK parameter = HIGH.
A Hide parameter if SYS.HIDE = ON.
The input lock is set with the “SYS.LOCK” parameter. It is deactivated by de-
fault. See page 33, parameter “SYS.LOCK”.
The value of the “parameter number” stands for the parameter that is displayed
after a certain time if no button is pressed during this time. It is set in the
“SYS.SD” parameter.
If the SD parameter has the value 1, for example, the parameter of the USER
parameter group whose parameter number has the value 1 is used.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
26 Chapter 8 Parameters
► Zero ± 4 % (of ADC.MAXR or TCON.MAXW) or tare: press for 1 sec-
ond.
► See page 30, parameter “TCON.KEY_S2”.
► See page 30, parameter “TCON.KEY_S4”.
► Format weight in the TCON.DDIV division for sending to the digital outputs
and Profibus DP: press .
Test sequence: ON for 5 seconds, OFF for 5 seconds, all outputs individually in
a one-second cycle.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 27
MAIN.NWT2 Level weight 2
0 … 999,999
Range of val- Level: M Default value: 10.00
ues:
► Switch between the job IDs for the job data: press .
► Switch to next or previous entry: press and + or .
► Switch to last entry: press , + and .
TCON.DDIV Division
Range of val- 0 … 999 Level: C Default value: 0.01
ues:
Unit: kg
Division (resolution) of the digital outputs and Profibus DP. Automatically set to
DIV when changing the ADC.DIV parameter.
Limit value for the DOUT OVF alarm and limitation of the digital outputs or Pro-
fibus DP.
When changing the weight output bits, the “Data ready” signal is at 0 V. If there
is a delay after TCON.TDRD, the signal switches to 24 V.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
28 Chapter 8 Parameters
TCON.OFOR Output format
Level: C Default value: BIN8
Value Function
Value Function
Value Function
Value Function
► Set TCON.OMODE = MP85 so that the data is output at the correct time.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 29
TCON.PBDAT Data on Profibus DP
Level: C Default value: JOBID
Value Function
Value Function
Value Function
Value Function
ZERO Zeroing.
TARE Taring.
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
30 Chapter 8 Parameters
Value Function
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 31
SYS.RIN 24 V input remote
Level: L Default value: OFF
Value Function
Value Function
Value Function
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
32 Chapter 8 Parameters
SYS.PSAV Power saving mode
Level: L Default value: STOP
Value Function
The value entered for the “SYS.SD” parameter relates to the parameter numbers
of the individual parameters in the USER parameter group. See tables for USER
parameter group. The parameter of the USER parameter group, the parameter
number of which corresponds to the value given here, is shown on the display
after 600 seconds as standard if no key is pressed during this time. The stand-
ard time for the change (600 seconds) can be changed in the SDT parameter.
The range stated here depends on the number of parameters in the USER pa-
rameter group for the respective application.
Value Function
0 No automatic change.
>0 If no button is pressed during the set time, the display changes to the standard
operating parameter. See “SYS.SD” parameter.
The “SYS.LOCK” parameter prevents certain parameters from being entered and
changed. It is always possible to display the parameters.
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 33
SYS.MSG Display messages
Level: L Default value: ALL
Value Function
Value Function
Value Function
► Select additional analog outputs: Press and hold down and press + .
► Select additional analog inputs: Press and hold down and press + .
► Note the setting at jumpers X62.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
34 Chapter 8 Parameters
SYS.AOADJ.x Align analog outputs
Range of val- 90.0 … 110.0 Level: L Default value: 100.0
ues:
Unit: %
► Select additional analog outputs: Press and hold down and press + .
► Select additional analog inputs: Press and hold down and press + .
Value Function
The Bühler standard baud rate of 200 and CAN-Open baud rates are supported.
■ 200
■ 10
■ 20
■ 50
■ 125
■ 250
■ 500
■ 800
■ 1000
► If lines are longer than 200 meters: Reduce the baud rate.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 35
SYS.ENET Ethernet interface ProfiNet or Ethernet/IP
Level: C Default value: OFF
Value Function
Value Function
► Reset all parameters: See page 25, chapter “Restoring factory settings”.
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
36 Chapter 8 Parameters
ADC.ZERO.x Zero scale
Level: C
The zeroing process sets the scale to a weight of zero. A rotating clock symbol
is displayed when zeroing.
The input value corresponds to the applied calibration weight. When calibrating,
a rotating clock symbol is displayed.
Value Function
Corresponds to pitch d. The smaller the value, the more accurately the scales
indicate the weight. If DIV is adjusted, all weight values are given a different val-
idity.
Value Function
NO No weight unit.
KG Weight unit kg. The "kg" LED is lit up when weight values are displayed.
LB Weight unit lb. The "lb" LED is lit up when weight values are displayed.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 37
ADC.FILT Number of weight values for digital filtering
2 … 128
Range of val- Level: C Default value: 2
ues:
Value Function
Tolerance in kg.
Value Function
ADC.NORM Calibratability
Level: C Default value: INDST
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
38 Chapter 8 Parameters
ADC.BCHNR Base channel
0 … 1
Range of val- Level: C Default value: 0
ues:
Value Function
Corresponds to waiting time between switching on the device and the weight
value being displayed.
Is only shown for calibratable applications. The display shows the value when
powering up too.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 39
8.3.3 HOST (SIO_1/SIO_2 serial interface) parameter group
Value Function
OFF No interface is being used. Neither interface, SIO_1 or SIO_2, is being used for
the host.
SIO1 Host interface connected to SIO_1 on the main circuit board.
SIO2 HOST interface connected to SIO_2 at X40.
Profibus DP not used, see X70, X71.
SIO12 HOST interface connected to SIO_1 on main circuit board and SIO_2 connected
to X40.
Profibus DP not used, see X70, X71.
RS422 HOST interface RS-422 with transmitter connected to SIO_1 on the main circuit
board and receiver connected to SIO_2 at X40.
Profibus DP not used, see X70, X71.
■ 4800
■ 9600
■ 19 200
Value Function
NO No parity bit.
EVEN Even parity bit.
ODD Odd parity bit.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
40 Chapter 8 Parameters
HOST.TOUT Timeout of the serial interfaces
Range of val- 0 … 99 Level: L Default value: 0
ues:
Unit: s
The device stops metering if no more communication has taken place during the
timeout time.
Value Function
0 No timeout monitoring.
1 … 99 Timeout in seconds. The monitoring is only active when “SYS.REM” = REMS.
Value Function
Value Function
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 41
8.3.4 ENET (Ethernet) parameter group
Current address for Profinet communication. The MEAG registers with this ad-
dress.
meag-123 (ENET.ADR = 123)
Only available with ProfiNet - “SYS.ENET” - P-NET.
In addition, the current bus status is shown.
Value Function
Value Function
NORM Normal protocol with 24-byte data for sending and receiving. For description,
see operating manual 66499.
SHORT Compact protocol DMS-T. Output byte not consistent (IM308B).
SHORTK Compact protocol DMS-T. Output byte consistent (IM308C).
EXTD_S Short extended protocol. Contains the NORM protocol with additional 32-byte
data.
EXTD_L Long extended protocol. Contains the NORM protocol with additional 48-byte
data.
ENET.IP IP address
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
42 Chapter 8 Parameters
ENET.SUBNET Subnet mask
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 43
ENET.GWSET.x Input new standard gateway. x = 0 … 3
0 … 255
Range of val- Level: C Default value: 0
ues:
The device triggers an alarm if no communication takes place during the timeout
time.
■ The monitoring is only active when “SYS.REM” = REME.
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
44 Chapter 8 Parameters
ENET.COM Communication status indicator
Value Function
NORM Normal protocol with 24-byte data for sending and receiving. For a description,
see operating manual 66499.
SHORT Compact protocol DMS-T. Output byte not consistent (IM308B).
SHORTK Compact protocol DMS-T. Output byte consistent (IM308C).
EXTD_S Short advanced protocol. Contains the NORM protocol with additional 32-byte
data.
EXTD_L Long advanced protocol. Contains the NORM protocol with additional 48-byte
data.
TCP.IP IP address
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 45
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
46 Chapter 8 Parameters
TCP.GWSET.x Input new standard gateway. x = 0 … 3
Range of val- 0 … 255 Level: L Default value: 0
ues:
The device triggers an alarm if no communication has taken place within the
specified time.
■ Monitoring is only active when “SYS.REM” = REMTCP.
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 47
PBDP.TOUT Timeout for Profibus-DP
0.1 … 99.9
Range of val- Level: L Default value: 1.0
ues:
Unit: s
The device stops metering if no more communication takes place during the
timeout time.
■ The monitoring is only active when “SYS.REM” = REMP.
Value Function
Value Function
NORM Normal protocol with 24-byte data for sending and receiving. For description,
see operating manual 66499.
SHORT Compact protocol DMS-T. Output byte not consistent (IM308B).
SHORTK Compact protocol DMS-T. Output byte consistent (IM308C).
EXTD_S Short extended protocol. Contains the NORM protocol with additional 32-byte
data.
EXTD_L Long extended protocol. Contains the NORM protocol with additional 48-byte
data.
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
48 Chapter 8 Parameters
PBDP.CTRLB Control bits display
Use analysis filter to select a data set from the Profibus protocol. Its value is
displayed via “PBDP.DAT”.
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 49
PBDP.DAT Data set value display
The counter is increased by 1 each time the data set defined by the filter is ac-
cessed.
SERV.DATE Date
Range of val- 00.01.01 … 99.12.31 Level: L
ues:
SERV.TIME Time
Range of val- 00.00.00 … 23.59.59 Level: L
ues:
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
50 Chapter 8 Parameters
SERV.ERR.x List of alarms
The last alarm is displayed in the form ERR.0 A006. The second to last alarm is
displayed with ERR.–1 etc.
Value Function
ON Recording activated.
OFF Recording deactivated.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 51
SERV.VLOG Internal recording of values
Level: C Default value: OFF
Value Function
ON Recording activated.
OFF Recording deactivated.
Value Function
Value Function
ON Recording activated.
OFF Recording deactivated.
Value Function
ON Simulation activated.
OFF Simulation deactivated.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
52 Chapter 8 Parameters
SERV.SERM Service mode
Level: C Default value: OFF
Value Function
ON Function activated.
OFF Function deactivated.
TEST Test mode for the print test.
► Select input (0.0 … 0.x): Press and hold down and press + or .
► Select output (0.0 … 0.x): Press and hold down and press + or
.
► Set or delete outputs if “SERV.SERM” = ON: Press .
Present current.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 53
► Select output: Press and hold down and press + or .
If OFF is displayed, no USB cable is connected. The following elements are dis-
played:
■ Left: Number of data packets received.
■ Right: Current utilization of the data transfer as %.
20 KByte/s = 100 %.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
54 Chapter 8 Parameters
SERV.P-DP Profibus DP status display
Display options:
Value Function
Is incremented by 1 each time RUN is switched to CAL. Is only shown for appli-
cations which can be calibrated.
Value Function
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 8 Parameters 55
9 Alarms and messages
Alarms and messages have the following syntax: The letter A for alarm or W for
warning followed by a three-digit number.
Example: A073.
Example: A073.2
A002 RAM
Cause Correction
The RAM is defective. ► Switch device off and on.
► If the alarm is repeated, replace main circuit board.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
56 Chapter 9 Alarms and messages
A003 RUNTIME
Cause Correction
Runtime error during the program ► Switch device off and on.
execution. Software or hardware ► If the alarm is repeated, note down “SERV.SADR” and
problem. contact Bühler customer service.
► Initialize data or load new program version.
► If the alarm is repeated, replace main circuit board.
A004 WATCHDOG
Cause Correction
Timeout during a program cycle. ► Switch device off and on.
Software or hardware problem. ► If the alarm is repeated, note down “SERV.SADR” and
contact Bühler customer service.
► Initialize data or load new program version.
► If the alarm is repeated, replace main circuit board.
A005 NO 24V
Cause Correction
The voltage is too low (< 18 V). ► Measure voltage at X1.
► If the voltage is lower than 18 V, locate the cause. The
power supply unit may be faulty or overloaded.
► If the voltage exceeds 18 V, replace main circuit board.
A006 DATALOST
Cause Correction
Loss of data in the battery-buffered ► Check that battery base is firmly in place.
RAM. The parameters and various ► If new software was loaded, acknowledge alarm.
data are reset to the original value. ► Disconnect the control system from the mains. Wait
Can occur during software down- 15 minutes. Switch on the control. If the alarm is repeat-
loads. ed, replace battery.
A007 RANGE
Cause Correction
The measuring range has exceed- ► Recalibrate.
ed or fallen below the normal limits. ► Check jumper X313.
► Check for foreign material on the weighing container,
e.g. have the transport locking devices been removed?
► Increase the value of the “ADC.MAXR” parameter or set
it to 0.
► Check the installation position of the force transducers.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 9 Alarms and messages 57
A008 ADCAL
Cause Correction
There are too few AD values for ► Recalibrate.
calibration. ► Check jumper X313.
► Check for foreign material on the weighing container,
e.g. have the transport locking devices been removed?
► Check the installation position of the force transducers.
► Apply sufficient weight for calibration to take place.
A009 ADFCT
Cause Correction
The AD converter module supplies ► Replace the main circuit board.
no values.
A011 LOW4MA
Cause Correction
Set point < 4 mA. Only possible if ► Measure the current.
the analog set point is 4 … 20 mA ► Set the counterpart to 4 … 20 mA.
(“SYS.REM” = REMA). ► Rectify line interruption.
► Check jumper X62.
A012 HOST COM
Cause Correction
Timeout on host interface. The host ► Run the host system.
system no longer communicates ► Check functionality or wiring of the interface cable.
with the device. ► Check jumper X31.
► Increase the timeout value of the “HOST.TOUT” param-
eter or set it to 0.
W013 EXTDISP
Cause Correction
Serial communication to remote ► Check the wiring.
control device interrupted. Only ► Check adjustment of X80.
possible with optional remote con- ► Check the value of the “SYS.DISP” parameter.
trol device.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
58 Chapter 9 Alarms and messages
A014 PROFI-DP
Cause Correction
Profibus error or communication ► Check the wiring.
has been interrupted (time-out). De- ► Check the address setting in the value of the
vice stopped. Alarm only if “PBDP.ADR” parameter.
“SYS.REM” = REMP. ► Check the adjustment of the operating mode in the val-
ue of the “PBDP.MPDP” parameter.
► Increase the timeout value of the “PBDP.TOUT” parame-
ter.
► Check master configuration.
W016 PRINTER
Cause Correction
Printer fault ► Refill with paper.
► Check whether printer is selected.
► Check value of “PRN.PSIO” parameter.
► Check the wiring.
W017 DISPLAY
Cause Correction
Communication to the primary dis- ► Check adjustment of X80.
play is interrupted. The display it- ► Set address on the display (see display alarm *No
self can no longer display the error. Comm An*).
► Check the wiring.
W018 BATTERY
Cause Correction
Buffer battery has insufficient volt- ► Check that battery base is firmly in place.
age or clock has stopped. ► Replace battery while device is switched on, then switch
control system off and back on again.
A070 CAN Ctn
Cause Correction
Interrupted communication with a ► Note error display on CAN module. Refer to description
CAN module. t = A (EBD 1317) of CAN extension modules in appendix.
t = D (EBD 1318/20) ► Check the wiring.
t = L (EBD 1319) n = 1…31 (mod- ► Check address setting on CAN modules.
ule address). If CAN COM is dis- ► Check whether configured CAN modules are present.
played, the whole bus is faulty.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 9 Alarms and messages 59
A071 CAN Mtn
Cause Correction
A CAN module transmits an error. ► Note error display on CAN module. Continue in accord-
t = A (EBD 1317) ance with the module description in the Appendix.
t = D (EBD 1318/20) ► Replace CAN module.
t = L (EBD 1319) n = 1…31 (mod-
ule address).
A072 CAN Dtn
Cause Correction
A CAN module has an output error. ► Note error display on CAN module. Continue in accord-
t = D (EBD 1318/20) ance with the module description in the Appendix.
t = L (EBD 1319) n = 1…31 (mod- ► Check wiring of digital outputs.
ule address). ► Check whether alarm stops when output plug connector
is disconnected.
A073 DEVNR
Cause Correction
The LC module has an incorrect in- ► Use the correct LC module.
ternal device number. Only with ► Set the upper device number from the calibration plate
calibratable make. on MEAG. See page 39, parameter “ADC.DEVNR”.
W075 WARNTEMP
Cause Correction
The temperature in the device is ► Check the temperature in the device.
too high. The temperature sensor is ► Install the device in a cooler location.
located on the display circuit board.
A076 HIGHTEMP
Cause Correction
The permissible maximum tempera- ► Check the temperature in the device.
ture in the device has been ex- ► Install the device in a cooler location.
ceeded. The temperature sensor is
located on the display circuit board.
A077 DIGOUT
Cause Correction
One or more of the outputs deviate ► Remove external voltage or overload sources.
from expected behavior.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
60 Chapter 9 Alarms and messages
9.3 Display alarm *No Comm An*
If this error is displayed, the connection to the circuit board is interrupted. The
configured address is displayed.
Enter address:
The 7-segment display shows the status and error messages. In the following
table, the status messages are listed on the 7-segment after the display.
Display Status
- Standard operation.
The middle seg- There are no messages.
ments are dis-
played cyclically
from top to bot-
tom.
L Software is installed and activated after the restart.
If the display is If the service tool is used, press <Activate software>. If the
flashing, the control system is disconnected from power supply, the new
download has not software is also activated.
yet been com-
pleted.
U USB connection active.
Device is connected to PC via a USB cable.
P Profibus is attached and connected.
For further information: See page 55, parameter
“SERV.P-DP”.
C New software is copied.
Program 1 is updated. Program 2 is copied. Status mes-
sage is displayed only during the startup phase.
F Program 1 is defective. Program 2 is copied.
Status message is displayed only during the startup phase.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 9 Alarms and messages 61
In the following table, the error messages are listed on the 7-segment after the
display. If an “E” flashes alternately with another symbol, an error message is
pending. “E d”, for example, indicates that “E” und “d” are flashing alternately.
1
Cause Correction
Fault in the FLASH memory. No ► Disconnect printed circuit board from power supply.
application present. No application Clean with compressed air.
started. ► Restart. If the error is repeated, replace printed circuit
board.
2
Cause Correction
Fault in the DRAM memory. No ap- ► Disconnect printed circuit board from power supply.
plication started. For example, as a Clean with compressed air.
result of a short circuit on the print- ► Restart. If the error is repeated, replace printed circuit
ed circuit board due to copper resi- board.
due.
b
Cause Correction
Fault in battery RAM memory. No ► Disconnect printed circuit board from power supply.
application started. Clean with compressed air.
► Restart. If the error is repeated, replace printed circuit
board.
E L
Cause Correction
Defective software version installed. ► Reinstall software. If the display does not change, re-
Program 1 shows an incorrect quest a new software version.
checksum. ► Disconnect device from power supply. After restart, pro-
gram 2 is used automatically.
E 3
Cause Correction
► See A003 RUNTIME
E 4
Cause Correction
► See A004 WATCHDOG
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
62 Chapter 9 Alarms and messages
E 5
Cause Correction
► See A005 NO 24V
E b
Cause Correction
► See W018 BATTERY
E 6
Cause Correction
► See A006 DATALOST
E C
Cause Correction
► See A070 CAN COM, A071 CAN MOD, A072
CAN DOUT
E d
Cause Correction
► See W017 DISPLAY
Some of the following messages are application-specific, i.e. they do not occur
with every control.
Display State
LOCAL STOP Device was stopped manually.
STOP Device was stopped because 0 V is present at the 24 V
input “Enable/Start”.
c STOP Device was stopped because no enable is connected via
Profibus or RS-485 (HOST).
v STOP Device was stopped because the set point is too low.
m STOP Device was stopped because no motor current is meas-
ured for the grinding motors. The motors were not start-
ed or the current measurement is not working.
Σ STOP Device was stopped because the required total or a re-
quired number was reached.
WAIT PRODUCT Device is started but no product is present (e.g. product
probe is uncovered).
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 9 Alarms and messages 63
Display State
REFILL Fill function is active (not normal filling).
SUSPEND The machine was started, but there is no feeding enable.
DISCHARGE Discharge function (or residual discharging) is active (not
normal emptying).
CAL MODE CAL mode is active. Calibration switch in CAL position.
SERVICE Service mode is active, i.e. “SERV.SERM” = ON (outputs
can be set).
LOCAL The device is operated locally. Only if REMOTE input is
active and 0 V is applied.
MANUAL The device is operated manually. No automatic control
sequence.
EMERGENCY Device is in emergency operation (“TCON.MODE”).
TEACHING Device is in learning mode.
HIGH SETP Set point is too high. The set point is limited to the max-
imum value.
SIM ON Simulator mode is activated, i.e. “SERV.SIMM” = ON.
SIM FREEZE Simulator mode is on but passive.
TEST Device is in test mode.
LOW SETP Set point is too low. The set point is limited to the mini-
mum or 0.
WARM UP Wait until the AD converter is stable.
STOP OPEN OK Device is stopped. All elements are in home position.
The machine may be switched off or opened.
OVERLOAD The grinding motor utilization has exceeded 130 %. The
grinding rollers were disengaged.
SAVE BUSY Automatic grinding gap adjustment has sent a save re-
quest. However, the message has not been acknowl-
edged by the host system.
HL INLET The product probe in the inlet signals that it is covered
(0 V). This message is only output if “TCON.HL IN” =
DIG_IN.
Some of the following messages are application-specific, i.e. they do not occur
with every control.
Display State
OK Input detected and applied.
Example: When a recipe has been loaded.
LOCK Parameter modification is locked.
See page 33, parameter “SYS.LOCK”.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
64 Chapter 9 Alarms and messages
Display State
REMOTE The control system is in remote operation mode, e.g. via
Profibus. Parameters can only be edited in remote oper-
ation mode, e.g: “SYS.REM” = REMP.
See page 31, parameter “SYS.REM”.
PROTECT Recipes are protected from being overwritten. The rec-
ipes cannot be saved.
DATA INIT Initialization is executed. The control is reset to default
values.
See page 36, parameter “SYS.INIT”.
SET ZERO Zero adjustment is executed.
See page 37, parameter “ADC.ZERO.x”.
SET CAL Calibration is executed.
See page 37, parameter “ADC.CALW.x”.
SET TARE Taring is executed.
WT INIT Weight values are re-initialized.
Example: If “ADC.DIV” is adjusted.
WAIT The device processes an order and prompts the operator
to wait.
Do not operate the control while WAIT is displayed.
CLEAR Data is being deleted.
ESC Modification has been aborted.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 9 Alarms and messages 65
10 Spare parts
MEAG with display in the stainless steel housing, IP65 Part. No.
115/230 V AC EKP -80060-810
24 V DC EKP -80081-810
115/230 V AC calibratable EKP -80154-810
24 V DC calibratable EKP -80153-810
10.2 Options
Option Part. No.
MEAG calibratable assembly (cover for the calibration EKP -80011-810
switch and the DMS terminals; may be installed later)
LC module in the housing (CAN extension load cell in a EKP -80118-810
terminal box; necessary for calibratability)
Analog module EBD 1317 e.g. for device type DEVICE EKP -80241-810
In stainless steel housing
Analog module EBD 1317 e.g. for device type DEVICE EKP -80242-810
In normal steel housing
MEAG display module (remote control / built-in version; EKP -80004-810
built into cabinet doors)
Remote control: table or wall model EKP -80042-810
Terminal box for 1 … 4 load cells, type VKK1-4 UXE -26527-301
Terminal box for 5 … 8 load cells, type VKK2-8 UXE -26527-303
Cable 6 x 0.75 mm², shielded UNE -30600-069
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
66 Chapter 10 Spare parts
10.3 Spare parts in stock
Stocks of spare parts and parts subject to wear are an important requirement for
the permanent operational readiness of the control system.
Bühler spare parts often fulfil special manufacturing and delivery specifications.
Bühler sells spare parts in accordance with state-of-the-art technology.
Only spare parts delivered by Bühler are inspected and approved. Spare parts
from other sources might negatively change the prescribed constructional quali-
ties of the control system and/or impair safety.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 10 Spare parts 67
Designation Part. No.
Interface converter RS-232/RS-485 MI400e-RD. For con- UXE -36906-003
nection to PC or as connection to a printer ML3320.
Display print and foil, assembled. EKP -80004-810
Display foil (without print). EKP -10006-010
Display 4-pole ribbon cable (EBD 1312 – EBD 1316). EKP -10007-010
Battery for the RAM. UNE -74921-029
BÜLTE retaining ring. UNN -14024-005
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
68 Chapter 10 Spare parts
11 Appendix
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 11 Appendix 69
11.2 DMS terminal box
11.2.1 Dimensions and technical specifications for terminal box VKK1-4
Material Aluminum
Degree of protection IP65
Weight 1 kg
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
70 Chapter 11 Appendix
11.2.3 4-wire force transducer with connection box
11.3 LC module
11.3.1 Dimensions and technical specifications
200
160
IO 24...27 IO 28...31
LC
1 1
H324 H328
2 2
7 6 5 4 3 2 1
CAN
H325 H329
3 3 1
4 4 2
150
110
5 5 3
H326 H330 H350
6 6 4
H327 H331
7 7 X100
8 8
X301 X302 X303 ON ON
1 2
OFF OFF
Out 28…31
Out 24…27 X99
EBD1319 3 4
NC
X312 S300
Technical data
Material Steel plate
Degree of protection IP65
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 11 Appendix 71
Technical data
Weight approx. 1 kg
Cable cross section max. 1.5 mm2
Lid can be lead sealed
Height 80 mm
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
72 Chapter 11 Appendix
11.4 CAN expansion modules
11.4.1 Types
11.4.2 Connection
Each CAN expansion module contains a 1-digit LED display; EBD 1320 has a
2-digit display. It indicates the hardware status.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 11 Appendix 73
A number from 1 … 9 indicates the address; a number from 1 … 31 for
EBD 1320. If several CAN expansion modules of the same type are present, dif-
ferent addresses must be set according to the I/O description of the application.
Set address:
E 1
Cause Correction
Software error ► Switch module off and back on again.
If the message is displayed again, re-
place module.
E 2
Cause Correction
EEPROM data loss ► Switch module off and back on again.
If the message is displayed again, re-
place module.
► Check whether the correct address is
displayed.
E 3
Cause Correction
No connection to CAN interface ► Press button and check address.
► Check settings of the parameters on
the MEAG.
E 4
Cause Correction
A/D converter error ► Switch module off and back on again.
If the message is displayed again, re-
place module.
E 5
Cause Correction
Digital outputs ► One or more of the outputs deviates
from expected behavior. (External
voltage, short circuit, overload).
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
74 Chapter 11 Appendix
E 6
Cause Correction
No external 24 V for EBD 1320 ► Check external 24 V at X105:1 plug.
LED 24 V EXT lights up when there
is voltage.
E b
Cause Correction
Automatic baud rate search (no ► Press button and check address. (For
connection to CAN interface). setting see address.)
► Check settings of the parameters on
the MEAG.
Fig. 11.1
Technical data
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 11 Appendix 75
11.5.2 Table or wall version
Fig. 11.2
Technical data
MEAG MEAG
Basisprint Anzeigeprint
EBD 1312 EBD 1316
X80
SIO_0 X50
1
2
6
X30
5
3 4
1 +24 V Line 1
1 1
2 0 V Line 2
2 2
3 RXD_TXD + 3 3
3
4 4 RXD_TXD - 4 4
X51
X51 SIO_0
SIO_0
X50
X30
Fig. 11.3
If the local display unit is removed from the control system and installed else-
where, it is to be connected as a remote control. Address 1 is still used, howev-
er, and the value of the parameter SYS.DISP will remain on OFF.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
76 Chapter 11 Appendix
With a distance of 5 m or more, use a shielded, 4-core cable.
2. Activate interface.
► Select SYS.DISP parameter.
► Press until parameter value flashes.
► Select the corresponding value. See page 32, parameter “SYS.DISP”.
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 11 Appendix 77
11.6 EU declaration of conformity
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
78 Chapter 11 Appendix
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 11 Appendix 79
Parameter list
Production plant:
Name:
Date:
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
80 Chapter 11 Parameter list
Parameter Default value Unit Customer value
SYS.SDT 600 s
SYS.LOCK OFF
SYS.MSG ALL
SYS.ACLR OFF
SYS.AINV ON
SYS.AO.x 0 mA
SYS.AI.x 0 mA
SYS.AOADJ.x 100.0 %
SYS.AIADJ.x 100.0 %
SYS.HIDE OFF
SYS.CANBR 200 kBaud
SYS.ENET OFF
SYS.TCP OFF
SYS.INIT
ADC.CHNR 0
ADC.WT.x kg
ADC.ZERO.x
ADC.CALW.x 40.000 kg
ADC.MAXR.x 0.000 kg
ADC.DIV 0.001
ADC.UNIT KG
ADC.FILT 2
ADC.MOT.x 0.5
ADC.TMOT 0.0 s
ADC.AZER 0.00 kg
ADC.NORM INDST
ADC.BCHNR 0
ADC.PUPT 10 s
ADC.ZADV.x 0
ADC.DADV.x 100 000
ADC.ADV.x
ADC.SWVERS
ADC.DEVNR 0
HOST.SIO SIO1
HOST.ADR 0
HOST.BAUD 4800
HOST.PARITY NO
HOST.TOUT 0 s
HOST.WFOR FIX
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 11 Parameter list 81
Parameter Default value Unit Customer value
HOST.ENBL OFF
HOST.COMP OFF
ENET.ADR 0
ENET.MPDP EXTD_L
ENET.IP
ENET.SUBNET
ENET.STDGW
ENET.IPSET.x 0
ENET.SNSET.x 0
ENET.GWSET.x 0
ENET.TOUT 1.0 s
ENET.STATUS
ENET.COM
TCP.MPDP EXTD_L
TCP.IP
TCP.SUBNET
TCP.STDGW
TCP.IPSET.x 0
TCP.SNSET.x 0
TCP.GWSET.x 0
TCP.TOUT 1.0 s
TCP.COM
PBDP.ADR 0
PBDP.TOUT 1.0 s
PBDP.WFOR FIX
PBDP.MPDP NORM
PBDP.COMP OFF
PBDP.CTRLB
PBDP.STATB
PBDP.DSDIR RXD
PBDP.DSNR 0
PBDP.DSIDX 0
PBDP.DSBYTE 8
PBDP.DSTYPE 1 BYTE
PBDP.DAT
PBDP.DSCNT
SERV.ID
SERV.V_PROG
SERV.V_APPL
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
82 Chapter 11 Parameter list
Parameter Default value Unit Customer value
SERV.V_BASE
SERV.V_BOOT
SERV.DATE
SERV.TIME
SERV.ERR.x
SERV.EVT.x
SERV.ALLEVT.x
SERV.CPU
SERV.SADR
SERV.PCNT
SERV.ELOG ON
SERV.VLOG OFF
SERV.CLOG ON
SERV.JLOG ON
SERV.SIMM OFF
SERV.SERM OFF
SERV.DIN
SERV.DOUT
SERV.DISPIN
SERV.AIN.x V / mA
SERV.AOUT.x mA
SERV.LC mV
SERV.TINT °C
SERV.SIO1
SERV.SIO2
SERV.USB
SERV.P-DP
SERV.CALCNT
SERV.CALDAT
SERV.PUPDAT
SERV.PDWDAT
SERV.TEST OFF
Bühler AG
MEAG-DMST-66698-7-1-1506-en-US
Chapter 11 Parameter list 83
Bühler AG
CH-9240 Uzwil, Schweiz
T +41 71 955 11 11
F +41 71 955 33 79
www.buhlergroup.com