Professional Documents
Culture Documents
Euro Power Brochure
Euro Power Brochure
R1 (MEETS / EXCEEDS THE REQUIREMENTS OF EN 853, ISO 1436 & SAE 100R1AT)
CONSTRUCTION TUBE APPLICATIONS
Oil resistant synthetic rubber Medium pressure hydraulic oil lines
Water and water-based fluid lines
REINFORCEMENT
One high tensile steel wire braid TEMPERATURE RANGE
-40ºC to +100ºC.
COVER Water & water-based fluids +70ºC max
Abrasion, ozone and weather resistant synthetic
rubber
federalhose.com/europower | 800-346-4673
RUBBER HOSES
R2 (MEETS / EXCEEDS THE REQUIREMENTS OF EN 853, ISO 1436 & SAE 100R2AT)
CONSTRUCTION TUBE APPLICATIONS
Oil resistant synthetic rubber High pressure hydraulic oil lines
Water and water-based fluid lines
REINFORCEMENT
Two high tensile steel wire braids TEMPERATURE RANGE
-40ºC to +100ºC.
COVER Water & water-based fluids +70ºC max
Abrasion, ozone and weather resistant synthetic
rubber
federalhose.com/europower | 800-346-4673
RUBBER HOSES
R16 (MEETS / EXCEEDS THE REQUIREMENTS OF SAE 100R16 & ISO 11237 R16)
CONSTRUCTION TUBE APPLICATIONS
Oil resistant synthetic rubber High pressure hydraulic oil lines where a tight bend radius
is required. Water and water-based fluid lines
REINFORCEMENT
Two high tensile steel wire braids TEMPERATURE RANGE
-40ºC to +100ºC.
COVER Water & water-based fluids +70ºC max
Abrasion, ozone and weather resistant synthetic
rubber
federalhose.com/europower | 800-346-4673
RUBBER HOSES
R17 (MEETS / EXCEEDS THE REQUIREMENTS OF SAE 100R17 & ISO 11237 R17)
CONSTRUCTION TUBE APPLICATIONS
Oil resistant synthetic rubber Hydraulic systems which operate at or below 210 bar and
require a tight bend radius
REINFORCEMENT Water and water-based fluid lines
1/4”-1/2” One high tensile steel wire braid
5/8”-1” Two high tensile steel wire braids TEMPERATURE RANGE
-40ºC to +100ºC.
COVER Water & water-based fluids +70ºC max
Abrasion, ozone and weather resistant synthetic
rubber
federalhose.com/europower | 800-346-4673
RUBBER HOSES
06 10 12 16 20 25 32
FITTING CODE HOSE TYPE 1/4" 3/8" 1/2" 5/8" 3/4" 1" 1.1/4”
04 06 08 10 12 16 20
SAE 100R16
SAE 100R17
The above crimping diameters are in inches and should be crimped to the specified diameter +/- 0.005”
(Crimping diameters in brackets are in meric and should be crimped to the specified diameter +/- 0.13MM)
Cut hose end square, lightly lubricate the hose bore with a compatible fluid, push the coupling fully on the hose, place the assembly in to the crimping machine die
set by 1.0 to 1.5mm (0.040-0.060”)
NOTE: Crimping machines with the floating head double taper die set are not suitable for crimping these couplings.
federalhose.com/europower | 800-346-4673
THERMOPLASTIC HOSES
federalhose.com/europower | 800-346-4673
THERMOPLASTIC HOSES
04 06 08
06 10 12
720
373
U MANDREL
HPT-16888-**U
NOTE: When using the “U” series ferrule with an ‘X’ series insert crimp to the above specified diameter +/- 0.13MM
IMPORTANT:
1. Do not use lubrication of any kind when assembling ET series inserts
2. If the above crimp diameters do not produce an insert bore collapse then they must be adjusted to do so. The collapse mandrel part numbers are as above
where ** denotes the insert tail size.
federalhose.com/europower | 800-346-4673
FITTINGS
DM&Q PROGRAM
Accepted industry standards are fine, as far as they go, but remember that standards such as DIN and SAE apply to the hose only, and not to the end connection or its
integrity with the hose. Mixing untested hose and fittings from a variety of sources with assembly techniques based on trial and error, rather than properly structured
development work and hours of impulse testing is, regrettably, an all too common occurrence – as common as hydraulic hose assembly failure, in fact.
Yet with your hydraulic life-blood at risk, it is vital that the whole assembly has complete integrity, is guaranteed to work and proven to be completely reliable.
The DM&Q emblem provides just this assurance and guarantees that a hose assembly has been Designed, Matched and Qualified for total integrity and maximum
performance.
Components are Designed – using the most advanced computer technology – to complement each type and dimension of hose perfectly, and Matched by highly trained
and specially qualified technicians to provide perfect couplings every time. Finally, the complete assembly is Qualified using the most rigorous testing procedures at our
own test house, to guarantee that it will measure up to the most exacting performance demands.
Instead of the risks of “mix-and-match” hose components, look for the DM&Q emblem. It is exclusive to Europower hose assemblies and is your guarantee of performance
assurance.
By effectively becoming part of a customer’s design team, Europower can not only ensure the integrity of the individual components, but also advise on the system layout.
This is called the Integrated Supplier Program and it plays a vital part in the quality equation.
Unsuitable installation, for example, can threaten the efficiency of an otherwise adequate system. Inconsistent flow conditions, twists in the hose, tight bends and poor
hose assembly routing can cause premature failure.
The design and installation of hose assemblies into complex machinery is inevitably one of the last tasks to be undertaken and quality is often compromised by the
immense pressures to met very tight prototype and production deadlines.
That is why Europower’s Integrated Supplier Program includes a closely-knit team of qualified engineers covering sales, design, cost and quotations and methods
engineering. They will not disappear the moment the order pad is signed. You can rely on their expertise to nurse the job through internal systems until production
deliveries are running regularly and consistently. It is this nursery approach that enables the smooth transition from prototype to production.
Therefore, what the Integrated Supplier Program offers is the most cost effective solution to the problem. What’s more, the cost is, for the first time, a single, known and
quantifiable cost because the unpredictable cost of failure – of downtime and warranty claims – is effectively removed from the equation.
federalhose.com/europower | 800-346-4673
FITTINGS
Please reference Hose type to find the Ferrule needed for the Thermoplastic one-piece Hose End.
federalhose.com/europower | 800-346-4673
FITTINGS
J.I.C. MALE
federalhose.com/europower | 800-346-4673
FITTINGS
federalhose.com/europower | 800-346-4673
FITTINGS
federalhose.com/europower | 800-346-4673
FITTINGS
federalhose.com/europower | 800-346-4673
FITTINGS
federalhose.com/europower | 800-346-4673
FITTINGS
federalhose.com/europower | 800-346-4673
FITTINGS
federalhose.com/europower | 800-346-4673
FITTINGS
federalhose.com/europower | 800-346-4673
FITTINGS
N.P.T.F. MALE
federalhose.com/europower | 800-346-4673
FITTINGS
federalhose.com/europower | 800-346-4673
FITTINGS
federalhose.com/europower | 800-346-4673
FITTINGS
federalhose.com/europower | 800-346-4673
FITTINGS
federalhose.com/europower | 800-346-4673
federalhose.com/europower | 800-346-4673