Professional Documents
Culture Documents
TC4 Series: Temperature Controller
TC4 Series: Temperature Controller
TC4 Series: Temperature Controller
TC4 Series
supply AC/DC Power 24VAC 50/60Hz, 24-48VDC
Allowable voltage range 90 to 110% of rated voltage
Power AC power Max. 5VA(100-240VAC 50/60Hz)
44.7
M A N U A L
45
48
consumption AC/DC Power Max. 5VA (24VAC 50/60Hz), Max. 3W(24-48VDC)
Display method 7Segment(Red), Other display(Green, Yellow, Red LED)
Character size(W×H) 7.0×15.0mm 7.4×15.0mm 9.5×20.0mm 9.5×20.0mm 7.0×14.6mm 11.0×22.0mm
Input RTD DPt100Ω, Cu50Ω (Allowable line resistance max.5Ω per a wire)
type TC K(CA), J(IC), L(IC) TC4Y Series 84
At room temperature(23℃±5℃): (PV ±0.5% or ±1℃, select the higher one) ±1digit 72 7 77
Display RTD
Out of room temperature range: (PV ±0.5% or ±2℃, select the higher one) ±1digit
accuracy※1
TC ※ For TC4SP, add ±1℃ by accuracy standard.
Control Relay 250VAC 3A 1a
36
30
output SSR 12VDC ± 2V 20mA Max. TC4H Series TC4L Series
Alarm output AL1, AL2 Relay: 250VAC 1A 1a(※TC4SP, TC4Y have AL1 only.) 48 6 64.5 96 6 64.5
Control method ON/OFF and P, PI, PD, PID control
Hysteresis 1 to100℃/℉(0.1 to 50.0℃/℉) variable TC4M Series
Proportional band(P) 0.1 to 999.9℃/℉ 72 6 64.5
Integral time(I) 0 to 9999 sec.
Derivative time(D) 0 to 9999 sec.
Thank you very much for selecting Autonics products. Control period(T) 0.5 to 120.0 sec.
Manual reset 0.0 to 100.0%
91.5
91.5
For your safety, please read the following before using.
96
Sampling period 100ms
67.5
Dielectric AC power 2,000VAC 50/60Hz for 1min.(Between input terminal and power terminal)
Caution for your safety strength AC/DC Power 1,000VAC 50/60Hz for 1min.(Between input terminal and power terminal)
Vibration 0.75mm amplitude at frequency of 5 to 55Hz in each of X, Y, Z directions for 2 hours
※Please keep these instructions and review them before using this unit. Mechanical OUT: Min. 5,000,000 operations, AL1/2: Min. 5,000,000 operations
Relay
※Please observe the cautions that follow; OUT: Min. 200,000 operations(250VAC 3A resistive load),
life cycle Electrical
AL1/2: Min. 300,000 operations (250VAC 1A resistive load)
Warning Serious injury may result if instructions are not followed. Insulation resistance Min. 100MΩ(at 500VDC megger) Bracket Panel cut-out Terminal cover(sold separately)
Caution Product may be damaged, or injury may result if instructions are not followed. Noise immunity
Memory retention
Square-wave noise by noise simulator(pulse width 1㎲) ± 2KV R-phase and S-phase
Approx. 10 years (When using non-volatile semiconductor memory type)
TC4S/TC4SP Series TC4Y Series RSA-COVER(48×48mm) RMA-COVER(72×72mm)
31 30 48.4 3 70 3
※The following is an explanation of the symbols used in the operation manual. A
Environ Ambient temp. -10 to 50℃, Storage: -20 to 60℃ 48.6 20
Caution:Injury or danger may occur under special conditions. -ment Ambient humi. 35 to 85%RH, Storage: 35 to 85%RH
12
10
45 5
Double insulation or reinforced insulation (mark: , Dielectric strength between the
41.5
Insulation type 60
68.5
Warning measuring input part and the power part: AC power 2kV, AC/DC Power 1kV)
64
Approval
B
1. In case of using this unit with machinery (Ex: nuclear power control, medical equipment, ship,
10
Approx. 141g Approx. 123g Approx. 174g Approx. 204g Approx. 194g Approx. 194g Approx. 254g C
44.9
vehicle, train, airplane, combustion apparatus, safety device, crime/disaster prevention equipment, Weight※2
36
16
18
(approx. 94g) (approx. 76g) (approx. 85g) (approx. 133g) (approx. 122g) (approx. 122g) (approx. 155g)
22
4.4
etc) which may cause damages to human life or property, it is required to install fail-safe device.
3.5
※1: Thermocouple L(IC) type, RTD Cu50Ω 9.8
13
It may cause a fire, human injury or damage to property.
2. Install the unit on a panel. At room temperature (23℃ ±5℃): (PV ±0.5% or ±2℃, select the higher one) ±1digit
Out of room temperature range: (PV ±0.5% or ±3℃, select the higher one) ±1digit 22.5
It may cause electric shock. 55 15 TC4M, TC4W, TC4H, TC4L Series Size
3. Do not connect, inspect or repair this unit when power is on. In case of TC4SP Series, ±1℃ will be added. A B C D
※2: The weight with packaging and the weight in parentheses is only unit weight. Model
It may cause electric shock. 21 RHA-COVER RLA-COVER(96×96mm )
3.3
4. Wire properly after checking terminal number. ※Environment resistance is rated at no freezing or condensation. TC4S Min. 65 Min. 65 45+0.6
0 45+0.6
0 (48×96mm, 96×48mm )
It may cause a fire. 47.2 4 94 3
Parts description TC4SP Min. 65 Min. 65 45 45
+0.6 +0.6
0 0
5. Do not disassemble the case. Please contact us if it is required.
4
It may cause electric shock or a fire. 56 46 TC4Y Min. 91 Min. 40 68+0.7
0 31.5+0.5
0
1
TC4M Min. 90 Min. 90 68+0.7 68+0.7
Caution
0 0
91.5
91.5
1 TC4H Min. 65 Min. 115 45+0.6 92+0.8
86
86
37.5
40.5
0 0
13
13
23.9
It may shorten the life cycle of the product and cause a fire. 1. Present temperature (PV) display 5. Control/alarm output indicator
4. Do not use beyond of the rated switching capacity of relay contact. RUN mode: Present temperature (PV) display. OUT: It will turn ON when control output(Main Control
It may cause insulation failure, contact melt, contact failure, relay broken and fire etc.
5. In cleaning unit, do not use water or organic solvent. And use dry cloth.
Parameter setting mode: Parameter or
parameter setting valuedisplay.
Output) is ON.
※In case of CYCLE/PHASE control of SSR drive
Connections SSR drive output selection function(SSRP function)[ SSrM ]
It may cause electric shock or a fire. 2. Deviation indicator, Auto-tuning indicator
output, it will turn ON when MV is over 3.0%. ※TC4 Series has selectable control output; Relay output, and SSR drive output. ● Realizing high accuracy and cost effective temperature control with both current output (4-20mA)
6. Do not use this unit in place where there are flammable or explosive gas, humidity, direct ray of the (only for AC power type) AC/DC power type does not have SSRP function. and linear output(cycle control and phase control)
It shows current temperature(PV) deviation
light, radiant heat, vibration and impact etc. AL1/AL2: It will light up when alarm output Alarm1/ ● SSRP function is selectable one of standard ON/OFF control, cycle control, phase control by utilizing
based on set temperature(SV) by LED. TC4S Series TC4SP Series
It may cause a fire or an explosion. Alarm2 are on.
No. PV deviation temp. Deviation display standard SSR drive output.
7. Do not inflow dust or wire dregs into the unit. 6. key SSR OUT: 6 ● Select one of standard ON/OFF control [ STND], cycle control[ CYCL] , phase control[ PHAS] at
1 Over 2℃ indicator ON 1 AL1 OUT: 7 -
It may cause a fire or a malfunction. Used when entering into parameter group, returning 12VDC ±2V 5 7 AL1 OUT:
20mA Max
250VAC 1A 1a Relay OUT 250VAC 1A 1a SSrM parameter of parameter 2 group. For cycle control, connect a zero cross turn-on SSR (a
8. Please wire properly after checking the terminal polarity when connecting temperature sensor. 2 Below ±2℃ indicator ON to RUN mode, moving parameter, and saving setting 2 8 250VAC 3A 1a
AL2 OUT:
4 8
+ random turn-on SSR is also available). For phase control, connect a random turn-on SSR.
It may cause a fire or an explosion. 3 Under -2℃ indicator ON values. 250VAC 1A 1a SSR OUT:
3 9 Temperature controller SSR voltage output
9. In order to install the units with reinforced insulation, use the power supply unit which basic Relay OUT: TC RTD B' 12VDC ±2V SSR module
The deviation indicators ( , , ) flash by 7. Adjustment B' RTD TC 3 9 (TC4Series) (12VDC)
insulation level is ensured. 4 250VAC 3A 1a
10 - 20mA Max
Load
(TC4SP is basic insulation only.) every 1 sec. when operating auto tuning. Used when entering into set value change mode, digit -
+ B
moving and digit up/down. B + 2 10 -
3. Set temperature(SV) indicator -
5 11
A +
Ordering information 1 11
8. FUNCTION key ※1
Press any front key once to check or ※1 +
6 12
A
SENSOR SOURCE
SOURCE SENSOR
change current set temperature(SV), the set Press + keys for 3 sec. to operate function(RUN/ 100-240VAC 5VA 50/60Hz 100-240VAC 5VA 50/60Hz
24VAC 5VA 50/60Hz
T C 4 S 1 4 R temperature(SV) indicator is ON and preset set STOP, alarm output cancel, auto-tunning) set in inner 24VAC 5VA 50/60Hz
24-48VDC 3W
24-48VDC 3W
value is flashed. parameter [DI-K].
TC4Y Series TC4H, TC4W, TC4L Series Power
Control output N Indicator - Without control output 4. Temperature unit(℃/℉) indicator ※Press + keys at the same time in set value
100-240VAC
R Relay output+SSR drive output※1 It shows current temperature unit. operation to move digit. 50/60Hz
AL1 OUT: Relay OUT: 1 13
250VAC 1A 1a 250VAC 3A 1a ※When selecting cycle or phase control mode, the power supply for a load and a temperature
Power supply 2 24VAC 50/60Hz, 24-48VDC Input sensor and temperature range[ IN-T] 2 14 controller must be the same.
4 100-240VAC 50/60Hz 1 2 3 4 5 6 7 8 9 10 11 ※In case of selecting cycle [ CYCL] or phase [ PHAS] control mode for PID control, control cycle [ T] is
Input sensor Display Input range (℃) Input range (℉) 3 15
N No alarm output A B B' -+ not allowed to set.
K(CA) KCA -50 to 1200 -58 to 2192
Sub output SSR OUT: 4 16 ※For AC/DC power model (TC4 - 2R), this parameter [SSrM] is not displayed and it is available only
1 Alarm1 output Thermocouple J(IC) JIC -30 to 500 -22 to 932 SENSOR RTD
12VDC ±2V
SOURCE ※1
standard control by relay or SSR.
2 Alarm1 + Alarm2 output※2 L(IC) LIC -40 to 800 -40 to 1472 20mA Max 100-240VAC 5VA 50/60Hz 5 17
TC 24VAC 5VA 50/60Hz 1)Standard ON/OFF control [ STND]
DPtH -100 to 400 -148 to 752 24-48VDC 3W
S DIN W48 H48mm(terminal block type) DPt100Ω 6 18 A mode to control the load in the AC
DPtL -100.0 to 400.0 -148.0 to 752.0 same way as Relay output type.
SP DIN W48 H48mm(11pin plug type) ※3 RTD
CUsH -50 to 200 -58 to 392 TC4M Series SSR OUT: 7 AL1 OUT: 19
(ON: output level 100%, OUT
Y DIN W72 H36mm Cu50Ω 12VDC ±2V 250VAC 1A 1a ON OFF ON OFF
Size CUsL -50.0 to 200.0 -58.0 to 392.0 20mA Max 8 20 OFF: output level 0%)
1 10 AL2 OUT:
M DIN W72 H72mm
Installation
250VAC 1A 1a
H DIN W48 H96mm 9 21 2)Cycle control [ CYCL]
2 11 Relay OUT:
●TC4S/SP(48 48mm) Series ●TC4Y(72 36mm) Series ●Other Series 250VAC 3A 1a B' RTD TC A mode to control the load by AC
W DIN W96 H48mm 10 22
3 12 - repeating output ON / OFF
L DIN W96 H96mm B + according to the rate of output
11 23
Digit SSR OUT: 4 AL1 OUT: 13 - within setting cycle. OUT
4 9999(4 Digit) 12VDC ±2V 250VAC 1A 1a +
12 24
A
Having improved ON / OFF noise
50Cycle 50Cycle
20mA Max ※1
Setting type 5 AL2 OUT: 14 SOURCE SENSOR
100-240VAC 5VA 50/60Hz feature by Zero Cross type. 50% 80%
C Set by touch switch 250VAC 1A 1a 24VAC 5VA 50/60Hz
Item 6 15 24-48VDC 3W
Relay OUT:
T Temperature controller B' RTD TC
3)Phase control [ PHAS]
250VAC 3A 1a
7 16 A mode to control the load by
※1: In case of the AC voltage model, SSR drive output method (standard ON/OFF control, cycle control, -