Professional Documents
Culture Documents
WheelHorse Electric Lift Accessory For 800 Series Tractors 8-4231
WheelHorse Electric Lift Accessory For 800 Series Tractors 8-4231
MODEL
8·4231
WHEEL-HORSE PRODUCTS, INC. • SOUTH BEND, IND. '
DESCRIPTION
The electric lift accessory provides powered opera-
tion of the lift arm on 800 Special and 800 Automatic
tractors. It is controlled with a switch on the dash
and uses battery power to raise and lower attach-
ments in place of the manual lift lever with which
these tractors are originally equipped.
FIGURE
9. 'he
underside of the
and furnished.
between tool tray
Do nut at this time.
A«"'~'I>ollt." ThIt."""'''1...
(1I.... ,."' ... L,,,,.n '5.""\"<", E"I'C..
FIGURE 7
t---------- 10,":.0
FIGURE 6
2-
19. Reinstall the fuel tank and connect the battery.
Operate the actuator switch to fully retract the actua-
tor shaft. Swing the pivot and lift arms rearward to
the limit of their travel. If they must be moved for-
ward again slightly before the holes in the actuator
clevis yoke will align with the clevis hole in the pivot
arm, install the clevis pin through the yoke and the
arm and secure it with the hairpin cotter (figure 9).
FIGURE 8
15. Install the lift link (12) to connect the lift arm Important
and pivot arm. Hold the link against the arms and
observe its relation to the tractor frame. It must be If the arms reach the rearward limit before the
parallel with the frame. Install spacers and washers clevis holes in yoke and pivot arm align, increase
as necessary at the pivot arm end to obtain proper the yoke-to-actuator shaft distance by turning the
clevis yoke (13) on the yoke stud until the holes will
alignment. Secure the link to the arms with cotter pins line up before the arms reach their rear limit stop.
furnished (figure 8). Tighten the jam nuts on the yoke stud securely. Flats
are provided for holding the actuator shaft with a
16. Install the clevis yoke (3), stud, and jam nuts wrench when tightening the rear jam nut.
in the end of the actuator shaft as shown in figure 10.
Run the yoke on the stud in until the distance from 20. Use the wire clips furnished to secure the
harness wire -along the hoodstand flange and frame
the center of the clevis pin hole to the end of the rail away from moving parts. Reinstall the fender and
actuator shaft is approximately 4Ys". Snug, but do not seat assembly and the footrest (use the x'6-18 x %
tighten the jam nuts against the yoke and actuator carriage bolt and nut at the footrest bracket). Tighten
shaft. all bolts and nuts used in the installation.
17. Insert the yoke end of the linear actuator (19) CAUTION: The actuator solenoid is continuously
from the right rear between the mounting frame energized and drawing battery current whenever the
brace and the transmission, and guide the assembly ignition key is in "Run and Accessories" position.
The ignition switch must be turned "Off" when the
into position. Withdraw the anchor pin (5) far enough
engine is not running to prevent the battery from
to allow the end of the linear actuator to fit between
discharging.
the mounting frame tabs and push the anchor pin
back into place. Secure it with a ~" washer and
hairpin cotter (figure 9). Plug the two-wire connector
on the harness wire into the mating connector on MAINTENANCE
the actuator wire.
lubricate pivot points with oil each time the tractor
is lubricated. The actuator is lubricated at the factory
18. Test operation of the system by temporarily
and needs no further attention. However, if the actua-
connecting the battery ground cable and quickly
tor shaft is to be left extended for a prolonged period
turning the actuator switch (16) on and off (the igni- outdoors, it would be well to wipe it with an oily
tion switch must be turned one notch to the right). rag to prevent rust.
Observe which direction the toggle must be moved to
start the actuator shaft moving outward. This is the To raise the seat and fender assembly for access
"UP': position of the switch and determines which way to the tool tray or transmission filler, withdraw the
the switch must be installed in the dash to agree with anchor pin from the rear mounting frame, lower the
the directions on the lift decal. Disconnect the battery linear actuator, and swing the upper support assem-
and install the actuator switch in the dash. bly to one side.
- 3
FIGURE 10
When ordering par!. alway. li.t Port No. and nome of Port.
Paris available only through Authorized Dealers.
(Sped/lcotioll' .",bied to change without notice.!