Professional Documents
Culture Documents
Tone Dialer With Built-In Piezo Driver: Pinout
Tone Dialer With Built-In Piezo Driver: Pinout
8230AS
driver for direct connection to a piezo-electric
buzzer. SCL BZH
OE BZL
The DTMF frequencies can be set to correspond to
the DTMF standards of any country. The output level VSS 4 5 CLK
is also adjustable under software control. These
features, combined with its small package and low
power dissipation, make the SM8230A a very use
device to use. PACKAGE DIMENSIONS
FEATURES
■ 3-line serial interface to external CPU
■ 2 independent, adjustable frequency outputs
4.4 0.2
6.2 0.3
■ Piezo driver for direct connection to a piezo-
electric buzzer
■ 4 system clock frequencies selectable (480 kHz,
960 kHz, 1.92 MHz, 3.84 MHz) + 0.10
5.2 0.3 0.15− 0.05
■ 2.6 to 3.3 V supply voltage
■ Low current consumption
• 3.0 mA (max) operating current
• 1 µA (max) standby current
■ 8-pin plastic SOP
1.27
1.5 0.1
0.05 0.05
0.4 0.1 0 10
0.4 0.2
BLOCK DIAGRAM
VDD
Programmable
D/A Output
Counter ROM BZH
Converter Control
High Group
SD
LATCH
SCL SELECTOR
OE
CLK
Programmable
D/A Output
Counter ROM
Converter Control BZL
Low Group
VSS
PIN DESCRIPTION
4 VSS – Ground
System clock input. The clock can be set to one of four frequencies (480 kHz, 960
5 CLK I
kHz, 1.92 MHz, 3.84 MHz).
SPECIFICATIONS
Absolute Maximum Ratings
VSS = 0 V
P arameter Symbol Rating Unit
Supply voltage range V DD −0.3 to 7.0 V
DC Characteristics
VDD = 2.6 to 3.3V, VSS = 0 V, Ta = −20 to 70 °C
Rating
P arameter Symbol Condition Unit
min typ max
V DD = 3.0 V, Ta = 25 °C,
Operating current consumption IDD – 1.5 3 mA
fCLK = 480 kHz
Standby current consumption IST V DD = 3.3 V, OE = LOW – – 1 µA
BZH/BZL tone output voltage VBZO 0 dB output level 0.86VDD 0.93VDD 1.0VDD Vp-p
AC Characteristics
VDD = 2.6 to 3.3V, VSS = 0 V, Ta = −20 to 70 °C
Rating
P arameter Symbol Condition Unit
min typ max
CLK
tCLKL tCLKH
tCLK
OE
SCL 1 2 16
tHDD
tSUOE tSCL tHDOE
Port OE BZH
R
Serial Clock SCL
CPU Serial Data SD SM8230
Piezo Buzzer
(Clock) CLK BZL
Command transfer The internal states are undefined when power is first
applied.
Data can be transferred when OE goes LOW. Data is
transferred in 16-bit units in sync with the rising DTMF analog signal output
edge of the SCL clock.
Data transfer stops and DTMF analog signal output
Note that when OE is LOW and both SD and SCL starts when OE goes HIGH, as shown in figure 2.
are tied LOW, the current consumption is less than 1
µA (standby mode).
Piezo buzzer
OE Serial data transmission
output
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SCL
b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
SD 0 0 CK1 CK0 FH1 FH0 GH3 GH2 GH1 GH0 FL1 FL0 GL3 GL2 GL1 GL0
MSB LSB
Low frequency
BZL group output
High frequency
BZH group output
b15(MSB) b0(LSB)
0 0 CK1 CK0 FH1 FH0 GH3 GH2 GH1 GH0 FL1 FL0 GL3 GL2 GL1 GL0
Table 3. FL command
DTMF
Design D e viation
FH1 FH0 frequency
value (Hz) (%)
(Hz)
0 0 0 0 −9 dB
0 0 0 1 −8 dB
0 0 1 0 −7 dB
0 0 1 1 −6 dB
0 1 0 0 −5 dB
0 1 0 1 −4 dB
0 1 1 0 −3 dB
0 1 1 1 −2 dB
1 0 0 0 −1 dB
1 0 0 1 0 dB
1 0 1 0 1 dB
1 0 1 1 2 dB
1 1 0 0 3 dB
1 1 0 1 4 dB
1 1 1 0 5 dB
1 1 1 1 6 dB
NIPPON PRECISION CIRCUITS INC. reserves the right to make changes to the products described in this data sheet in order to
improve the design or performance and to supply the best possible products. Nippon Precision Circuits Inc. assumes no responsibility for
the use of any circuits shown in this data sheet, conveys no license under any patent or other rights, and makes no claim that the circuits
are free from patent infringement. Applications for any devices shown in this data sheet are for illustration only and Nippon Precision
Circuits Inc. makes no claim or warranty that such applications will be suitable for the use specified without further testing or modification.
The products described in this data sheet are not intended to use for the apparatus which influence human lives due to the failure or
malfunction of the products. Customers are requested to comply with applicable laws and regulations in effect now and hereinafter,
including compliance with export controls on the distribution or dissemination of the products. Customers shall not export, directly or
indirectly, any products without first obtaining required licenses and approvals from appropriate government agencies.
NC9614BE 1997.01