Professional Documents
Culture Documents
Hydraulic Power Units: D, H and V-Pak Series
Hydraulic Power Units: D, H and V-Pak Series
Volume Control
Hydraulic
Power Units
D, H and V-Pak Series
HY28-2661-CD/US zpu03
H-Paks 37.9 (10), 75.7 (20), 113.6 (30), 151.4 (40) 2.2 - 26.1 (0.9- 6.3) 0.37 (0.5) - 14.9 (20) 207 (3000)
V-Paks 37.9 (10), 75.7 (20), 113.6 (30), 151.4 (40) 7.6 - 59.1 (2.0 - 15.6) 1.5 (2) - 14.9 (20) 207 (3000)
Warranty
The hydraulic components on these Parker Power
Units are warranteed for one year. This warranty
may be extended to two years by using and
properly maintaining Parker filters.
Installation Data:
See Installation/Maintenance Manual for specific
recommendations pertaining to start-up, system
cleanliness, fluids, temperature and other important
factors relative to proper installation and use of
these power units.
Standard Features
• Vertical Design Benefits
• Submerged Pump • Saves Floor Space
• Spare Return Ports • Quieter Operation, Elimination of Potential
• Precision Pump Mounting Adapters Leak Point
• Glycerine Filled Pressure Gage with Shut Off • Protects Pump from Contamination
Schematic Symbol
(Hydraulic Schematic - Basic Unit)
P T P T
“O” “O”
OPTION X P A X OPTION X P A X
MANIFOLD MANIFOLD
T B X T B X
M SPARE
M SPARE
RETURN RETURN
“OMIT”
OPTION
COMP
CONTROL
SAE X SAE X
-12 -12
D-Paks
Omit If Not Omit If Not
Required Required
W
Reservoir Pressure Pump No Motor Electric Manifold
Control Flow (See Note) Motor
**
Ordering
Pump Used Comments
Code
0.9 331-9110-264 Available With
1.3 331-9110-265 0.37 KW (0.5 HP)
1.8 331-9110-266 Motors Only
2.7 331-9110-263
Pressure and Return Port Block “P” & “T” Ports Convertible to
O
with Safety Relief Valve SAE-10 Str. Thr’d S3 Option
D03 Single Station Subplate “A” & “B” Ports Spare “P” & “T”
S3
with Safety Relief Valve SAE-8 Str. Thr’d SAE-10 Ports
D03 Multistation Parallel Circuit Manifold “A” & “B” Ports Spare “G” Port
M33
with Safety Relief Valve SAE-8 Str. Thr’d SAE-6
NOTE:
Manifolds are mounted vertically.
Bottom station is number 1.
D-Paks
Omit If Not Omit If Not Omit If Not
Required † Required Required
P
Directional *Manapak Options Consult Factory
Control Valve Control Valves and For Special Modifications
Accessories
(Spr. Ctr) P T
R2 Float/Temp. Switch 876782-02 Open @ Low Level and/or
Double A B Float Up 65.6°C (150°F) (N.C.)
➤
➤
(Spr. Ctr)
➤
P T
*Heat rejection based on flow given with a 40°F differential between transfer
Double A B
medium.
➤
(Spr. Ctr)
➤
➤
P T
† Units less valves will be supplied with station cover plates installed.
H-Paks
Omit If Not Omit If Not
Required Required
W
Reservoir Pressure Pump No Motor Electric Manifold
Control Flow (See Note) Motor
**
Ordering Reservoir Size Ordering Code Motor Description
Code Liters (Gallons) (KW (HP)-RPM-Frame-Phase)
NOTE:
Manifolds are mounted vertically.
Bottom station is number 1.
H-Paks
Omit If Not Omit If Not Omit If Not Not Required
Required † Required Required When Ordering
P
Directional *Manapak Options Consult Factory For Design Series
Control Valve Control Valves and Special Modifications
Accessories
Valve NFPA Nominal
Ordering Circuit
Function Model Mounting Flow Ordering Model Technical
Code Number Pad LPM(GPM) Symbol
Code Function Number Data
Flow A B Air/Oil: .52 KW (.7 HP)
1 FM2DDKN D03 26.5 (7) Return Heat
Control B1* RM-08-1-2 Rejection @ 26.5 LPM (7 GPM)
Exchanger
A B (.37 - 3.7 KW
Flow (.5 - 5 HP) Motors Only)
2 FM3DDKN D05 45.4 (12)
Control
Air/Oil: 1.1 KW (1.5HP)
Pilot Operator A B Return Heat
3 CPOM2DDN D03 26.5 (7) B2* RM-190-1-2 Rejection @ 26.5 LPM (7 GPM)
Check Exchanger
(5.6 - 11.2 KW
Pilot Operator A B (7.5 - 15 HP) Motors Only)
4 CPOM3DDN D05 45.4 (12)
Check Microglass II Element
Pressure
H 15P110QXRS Vis. Ind. -3.49 Bar (50 PSI )
*Manapak valves mounted in order of callout. First valve will be nearest DCV; Filter
Bypass (.27 Bar (4 PSI) Diff.
last valve will be on manifold. @ 26.5 LPM (7 GPM))
.34 Bar (5 PSI)
Check Valve “DT” & “C”
K Cracking Pressure
Pump Outlet Series
(1.72 Bar (25 PSI) Diff.
@ 56.8 LPM (15 GPM))
Bypass Check 4.5 Bar (65 PSI)
L C1220S65
(On Heat Exch.) Cracking Pressure
Microglass II Element
Return
N 40CN110Q Visual 1.72 Bar (25 PSI) Indicator
Filter
(.2 Bar (3 PSI) Diff.
@ 26.5 LPM (7 GPM))
Valve NFPA Nominal 12AT10C Cellulose Element
Ordering Circuit Return
Model Mounting Flow Description O (45.2 LPM (12 GPM) Ind. Gage -
Code Symbol Filter
Number Pad LPM(GPM) Max. Oil Flow) 1.03 Bar (15 PSI) Bypass
A B
Double
➤
➤
(Spr. Ctr) P T
R1 Float/Temp. SW 876782-01 Close @ Low Level
Double A B
N.O. Float Up And/Or 65°C (149°F) (N.O.)
➤
➤
(Spr. Ctr) P T
Combination Fixed Temp at 65.6°C (150°F)
Double A B
R2 Float/Temp. SW 876782-02 Open @ Low Level
➤
➤
F D3W1CN** D05 75.7 (20) N.O. Float Up And/Or 65.6°C (150°F) (N.C.)
➤
➤
(Spr. Ctr) P T
Double A B
*Heat rejection based on flow given with a 4.4°C (40°F) differential between
➤
➤
(Spr. Ctr)
➤
P T
A B
Double
➤
➤
(Spr. Ctr) P T
A B
Double
➤
➤
(Spr. Ctr) P T
7 OR Reduced
Flow W
Reservoir Remote Pump Pump No Motor Electric Manifold
Compensator Control Flow (See Note) Motor
Options
**
Ordering Reservoir Size Ordering Pump Control Ordering Code Motor Description (KW (HP)-RPM-Frame)
Code Liters (Gallons) Code Option
G 1.5 (2) - 1725 - 56C - 3
V1* 37.9 (10) Std. Remote
Omit K 2.2 (3) - 1725 - 56C - 3
Compensator
V2 75.7 (20)
L 3.7 (5) - 1725 - 184TC - 3
Load Sense
V3 113.6 (30) A* M 5.6 (7.5) - 1725 - 213TC - 3
(Flow Control)
V4 151.4 (40) N 7.5 (10) - 1725 - 215TC - 3
Horsepower
*Available up to 7.5 KW H**
Limiting P† 11.2 (15) - 1725 - 254TC - 3
(10HP) motor.
S† 14.9 (20) - 1725 - 256TC - 3
NOTE: For shaded options
Electric motors are 208-230/460V, 60Hz, 3PH 1800 RPM. TEFC
A & H, lead time
consult factory for other motor speeds (RPM) and voltages.
is four weeks.
** Use “W” prefix when no motor is required on unit. When
* Unless otherwise ordering, “W” must be followed by motor model code
specified, a SAE-6 sense equivalent to frame size of motor to be used.
Ordering Compensator port line will be supplied in
Code Description topplate.
Ordering Pump Flow Rate
Single Pressure When shuttle check option Pump Used and Description
Omit Code @ 1800 LPM (RPM)
Remote Compensator (9 or 0) is specified on
D03 or D05 manifold, 7 29.5 (7.8) PVP16 - Std. Remote Compensator
Single Pressure sense line will be plumbed
B Specify in GPM Destroked Max. Volume
Remote Compensator to shuttle check. *
With Low Pressure 7.57 LPM (2 GPM) Min.
** Unless otherwise
Standby specified, horsepower * Unless otherwise specified, units are shipped at max. flow rate (29.5 LPM
setting will be (7.8 GPM)) at 1800 RPM. When reduced flow setting is required, specify
Single Pressure at max. flow & pressure pump setting in .5 GPM increments. Example: 5, 5.5, 6, 6.5 with a 2 GPM
BJ minimum flow.
Remote Compensator obtainable with motor
With Low Pressure selected. Reference Pump If horsepower limiting pump (H) control is required to be destroked, utilize
Standby, 24VDC HP curves. the special ordering code X.
Example: V*5**-- = Std. Pump Destroked to 5 GPM
Bi-Pressure Remote V*A4.5**-- = Load Sense Pump Destroked to 4.5 GPM
C
Compensator
Bi-Pressure Remote
CJ
Compensator, 24 VDC Ordering Supply/Return Port
Pump Control/Mounting Other
Code Actuator Port Size
Bi-Pressure Remote
Compensator With Pressure and Return Port Block “P” & “T” Port Convertible to
D O
Low Pressure Standby with Safety Relief Valve SAE-12 Str. Thr’d S3, S5, S6 Option
Bi-Pressure Remote D03 Single Station Subplate “A” & “B” Ports Spare “P” & “T”
S3
Compensator With with Safety Relief Valve SAE-8 Str. Thr’d SAE-10 Ports
DJ
Low Pressure
Standby, 24VDC D05 Single Station Subplate “A” & “B” Ports Spare “P” & “T”
S5
with Safety Relief Valve SAE-10 Str. Thr’d SAE-12 Ports
Provision For
Customer Supplied M33 D03 Multistation Parallel Circuit Manifold “A” & “B” Ports Spare “G” Port
F
Remote Control Relief M35 with Safety Relief Valve SAE-8 Str. Thr’d SAE-6
Valve
M53 D05 Multistation Parallel Circuit Manifold “A” & “B” Ports Spare “G” Port
M55 with Safety Relief Valve SAE-8 Str. Thr’d SAE-6
* When ordering Multi-Station Manifolds, the number of stations must be specified. If more than 5 stations
required, consult factory. If valves are to be mounted, specify the valves and sequence. If the model code
exceeds 25 digits, utilize the special ordering code X.
Example: V2 7 N M33X NOTE:
X= 3 Station Manifold Manifolds are mounted vertically.
Station #1: A Bottom station is number 1.
Station #2: B
Station #3: C24
F D3W1CN** D05 75.7 (20) N.O. Float Up And/Or 65.6°C (150°F) (N.C.)
➤
➤
(Spr. Ctr) P T
A B *Heat rejection based on flow given with a 4.4°C (40°F) differential between
Double
➤
transfer medium.
➤
(Spr. Ctr) P T
† Units less valves will be supplied with station cover plates installed.
Note: Refer to options and accessories for voltage and connection choices.
15 OR Reduced
Flow W
Reservoir Remote Pump Pump No Motor Electric Manifold
Compensator Control Flow (See Note) Motor
Options
**
Ordering Reservoir Size Ordering Pump Control Ordering Code Motor Description (KW (HP)-RPM-Frame)
Code Liters(Gallons) Code Option
L 3.7 (5) - 1725 - 184TC - 3
V2 75.7 (20) Std. Remote
Omit M 5.6 (7.5) - 1725 - 213TC - 3
Compensator
V3 113.6 (30)
Load Sense N 7.5 (10) - 1725 - 215TC - 3
V4 151.4 (40) A*
(Flow Control) P 11.2 (15) - 1725 - 254TC - 3
Bi-Pressure Remote
CJ
Compensator, 24 VDC
Ordering Porting Block/Subplate Supply/Return Port
Bi-Pressure Remote Other
Code or Manifold Type or Actuator Port Size
Compensator With
D Pressure and Return Port Block “P” & “T” Ports Convertible to
Low Pressure O
Standby with Safety Relief Valve SAE-12 Str. Thr’d S3, S5, S6 Option
Bi-Pressure Remote D03 Single Station Subplate “A” & “B” Ports Spare “P” & “T”
S3
Compensator With with Safety Relief Valve SAE-8 Str. Thr’d SAE-10 Ports
DJ
Low Pressure
D05 Single Station Subplate “A” & “B” Ports Spare “P” & “T”
Standby, 24VDC S5
with Safety Relief Valve SAE-10 Str. Thr’d SAE-12 Ports
Provision For
M33 D03 Multistation Parallel Circuit Manifold “A” & “B” Ports Spare “G” Port
F Customer Supplied
M35 with Safety Relief Valve SAE-8 Str. Thr’d SAE-6
Remote Control
Relief Valve M53 D05 Multistation Parallel Circuit Manifold “A” & “B” Ports Spare “G” Port
M55 with Safety Relief Valve SAE-8 Str. Thr’d SAE-6
NOTE:
Manifolds are mounted vertically.
Bottom station is number 1.
Return
➤
B D1VW001CN*** D03 26.5 (7) O [45.2 LPM Ind. Gage - 1.03 Bar (15 PSI)
(Spr. Ctr)
➤
➤
P T Filter
(12 GPM) Bypass
Double A B
Max. Oil Flow]
➤
➤
(Spr. Ctr)
➤
P T
Combination Fixed Temp at 65°C (149°F)
Double A B
R1 Float/Temp. SW 876782-01 Close @ Low Level
➤
➤
F D3W1CN** D05 75.7 (20) N.O. Float Up And/Or 65°C (149°F) (N.O.)
➤
➤
(Spr. Ctr) P T
P T
N.O. Float Up And/Or 65.6°C (150°F) (N.C.)
† Units less valves will be supplied with station cover plates installed. *Heat rejection based on flow given with a 4.4°C (40°F) differential between
Refer to options and accessories for voltage and connection choices. transfer medium.
381.0 (15.0)
19.1
(.75) 342.9 (13.5)
T
22.9 B A
(.9)
PRESSURE GAGE
WITH NEEDLE VALVE
SPARE RETURN PORT
1/2" NPTF
WITH DROP PIPE
B A FILLER
BREATHER
T
OIL LEVEL
SIGHT GAGE
263.1
(10.36) TANK DRAIN
SAE-12 (PLUGGED)
38.1
(1.5)
“M3*” & "C3*" OPTION MANIFOLD
(MULTI-STATION D03 MANIFOLD)
SHOWN WITH OPTION “O” RETURN FILTER
3.1
307.9 (.12)
(12.12)
33.3
“B” (1.31)
.56 DIA. MOUNTING
HOLES - 4 PLACES
T
DROP PIPE
ELECTRIC MOTOR
P
355.6
(14.00)
FOR H-PAKS
SAFETY RELIEF VALVE
P
FOR V-PAKS
ROTATION ARROW
A-D03 B-D03
B-D05 A-D05
PRESSURE GAGE
WITH NEEDLE VALVE
OIL LEVEL
SIGHT GAGE
38.1
P
(1.5)
38.1 IN
“B” (1.5)
.56 DIA. MOUNTING
HOLES - 4 PLACES
T
(17.0) ELECTRIC MOTOR
P
508.0 PUMP PREFILL PORT
(20.0) FOR V-PAKS (8-15 GPM ONLY)
“O” & “S5” OPTION MANIFOLD
(P & T BLOCK & D05 SINGLE STATION)
SYSTEM RELIEF VALVE SHOWN WITH OPTION “N” RETURN FILTER
FOR H-PAKS
T
FOR V-PAKS
PRESSURE GAGE
WITH NEEDLE VALVE A-D03 B-D03
B-D05 A-D05
FILLER
BREATHER
OIL LEVEL
SIGHT GAGE OUT
TANK DRAIN IN
38.1
(1.5)
T
P
495.3 3.1
(19.5) (.12)
Manifold Options
Inch equivalents for millimeter dimensions are shown in (**).
X
RETURN P T “A” RETURN P T “A”
PORT X P A X PORT PORT X P A PORT
SAE-10 SAE-8 SAE-10 SAE-8
T B
“B” T T B
“B” T
X PORT PORT
D03 SAE-8 D03 SAE-8
87.4 P P
COVER (3.44) 52.3 MNTG
PLATE SURFACE
(2.06) 31.8
(1.25)
44.2
PUMP (1.75) PUMP
SUPPLY SUPPLY
B A B A
85.9
(3.38) 47.8
(1.88)
22.0 44.5
(.87) (1.75)
O S3
T B X PORT T
B
PORT T
44.5
D05 SAE-10 (1.75) D05 SAE-10
P
COVER MNTG
PLATE 53.8 SURFACE
RETURN (2.12) RETURN 31.8
PORT X PORT X (1.25)
SAE-12 SAE-12
44.5
PUMP (1.75) PUMP
SUPPLY SUPPLY
17.5 53.8
(.69) (2.12)
O S5
MANIFOLD OPTION
FOR SUPPLY & RETURN CONNECTIONS SUBPLATE OPTION
(37.9, 75.7, 113.6, 115.4 LIT FOR USE WITH D3W VALVE
(10, 20, 30, 40 GAL) RESERVOIR UNITS) (NFPA D05)
Manifold Options
Inch equivalents for millimeter dimensions are shown in (**).
RETURN
PORT
Option M33/M35 SAE-10
X
P T
A
3 AND 5 STATIONS)
"A"&"B"PORTS
B
SAE-8
T
A
G B
"G"
SAE-6 D03
MNTG
SURFACE
33.3
(1.31)
PUMP
SUPPLY
54.0
(2.12)
PER STATION
3 AND 5 B A
STATION
G
AVAIL. 54.0
4.25 B A (2.12)
22.1 1.06
(0.87)
44.5
(1.75)
RETURN
PORT
Option M53/M55 SAE-12
X
P T
A
3 AND 5 STATIONS
"A"&"B"PORTS
B
SAE-8
A
P
G B
"G"
SAE-6 D05
MNTG
SURFACE 31.8
(1.25)
PUMP
SUPPLY
82.6 (3.25)
PER STATION
3 AND 5 B A
STATION
AVAIL. G
165.1 82.6
(6.50) (3.25)
B A
39.6
17.5 (1.56)
(0.69)
54.0
(2.12)
T T
INVERTED
INVERTED
UPRIGHT
UPRIGHT
P
B A
B A G
B A
T T
INVERTED
INVERTED
UPRIGHT
UPRIGHT
P
B A
B A G
B A
T
INVERTED
UPRIGHT
B A
"D"PAK WITH
"OMIT" MANIFOLD
(CONNECTED TO SYSTEM RETURN
P T HIGH
SOL
P
P
SAE
SOLENOID IS LOW WATT
-6 WITH DIN. 43650 CONNECTOR
AND MANUAL OVERRIDE
HI LO
SOL SOL
HI
LO
“C” OPTION T
“D” OPTION T
BI-PRESSURE HIGH LOW BI-PRESSURE HIGH LOW
PSI PSI LOW SOL
REMOTE COMPENSATOR PSI REMOTE COMPENSATOR PSI
STANDBY
W/LOW PRESS. STANDBY
HIGH HIGH
SOL SOL
P P
HI LO HI LO
SOL SOL SOL SOL
HI HI
LO LO
“F” OPTION
PROVISION FOR
CUSTOMER SUPPLIED
REMOTE COMPENSATOR
SAE -6
37 FLARE
P T
P P
T
T
PUMP COMPENSATOR
PRESSURE (INLET) PORT
PUMP COMPENSATOR
TANK (RETURN) PORT
Accessory Options
D & H-PAKS
Option B Return Line Air/Oil Heat Exchanger (B1 or B2) Option N Return Line Filter
Option H Pressure Filter Option O Return Line Filter
Option K Check Valve – Pump Outlet Option R Combination Temp/Level Switch (R1 or R2)
Option L Check Valve – Return Line Bypass
SEE MANIFOLD
OPTIONS
P T
H L N O
SAE-10
SAE-6
1/2"NPT-"D"PAKS SAE-10
3/4"NPT-"H"PAKS
B K
M
R
SAE
X
-12
V-PAKS
Option A Pump Case Heat Exchanger Option L Check Valve – Return Line Bypass
Option B Return Line Air/Oil Heat Exchanger (B1 or B2) Option N Return Line Filter
Option H Pressure Filter Option O Return Line Filter
Option K Check Valve – Pump Outlet Option R Combination Temp/Level Switch (R1 or R2)
SEE MANIFOLD
OPTIONS
P T
H L N O
SAE-10
SAE-6
SAE-10
A B K
SEE
M COMPENSATOR
OPTIONS
3/4"
NPT R
SAE
X
-12
CONNECTED TO RETURN
LINE WITH OPTION "B"
19.8
[0.78]
P
10.8
[0.43]
129.5
[5.1]
OPTION "B1" REF.
AIR/OIL
HEAT EXCHANGER
16.3
[0.64]
16.9
[0.67]
12.7
[0.50]
10.2
[0.40]
T
T
P
P
32.0
[1.26]
26.5
89.7
[1.04] [3.53]
DIM DIM
"A" "A"
REF OPTION "R1" OR" R2" REF
FLOAT/TEMP. SWITCH
(1/2" ELEC. CONN.)
A-D03 B-D03
OPTION "H" A-D03 B-D03
B-D05 A-D05
PRESSURE FILTER B-D05 A-D05
FLOAT 2"
BELOW
LOW LEVEL
105.2
[4.14]
53.5
[2.11] 19.1
[0.75]
T
3/4" NPTF
WITH DROP PIPE
P
P
OPTION "B2"
128.0
AIR/OIL [5.04]
HEAT EXCHANGER OPTION "A"
PUMP CASE HEAT EXCHANGER
(USED ON V-PAKS ONLY)
129.5 124.5
[5.10] [4.90] 89.7
[3.53]
DIM DIM
"A" "A"
REF OPTION "R1" OR "R2" REF
FLOAT/TEMP. SWITCH
(1/2"ELEC. CONN.)
OPTION "H"
PRESSURE FILTER
FLOAT 2"
BELOW
LOW LEVEL
q
38.0
[1.49]
90 34.1 9 90 68.2 18
Efficiency - %
Overall Efficiency
Overall Efficiency
80 30.3 8 80 60.6 16
Flow
70 26.5 7 Flow 70 53.0 14
60 22.7 6 60 45.4 12
KW HP KW HP
Flow
Flow
w
15.1 4 11.9 16.0 30.3 8 lo 23.9 32.0
F low l lF
ull t Fu
Power
Power
22.7 6 17.9 24.0
ra
11.4 3
tF
8.9 12.0
a e
er ow
7.6 2 ow 6.0 8.0 15.1 4 tP 11.9 16.0
u tP pu
In
3.8 1
Inp 3.0 4.0 7.6 2 6.0 8.0
Power wer
Compensated Compensated Po
0 0 0 0 0 0 0 0
Bar 0 69 138 207 275 Bar 0 69 138 207 275
PSI 0 1000 2000 3000 4000 PSI 0 1000 2000 3000 4000
Pressure Pressure
NOTE: The efficiencies and data in the graph are good WHERE:
only for pumps running at 1800 RPM and stroked to Q = Actual Output Flow in GPM
maximum. To calculate approximate horsepower for the
other conditions, use the following formula: PSI = Pressure At Pump Outlet
CHp= Input Horsepower @ Full compensation
HP = [ Q x (PSI)
1714 ] + (CHp) x
1800
N
@ 1800 RPM (from graph read at
operating pressure)
Actual GPM is directly proportional to drive speed and
maximum volume setting. Flow loss, however, is a N = Drive Speed in RPM
function of pressure only.
6 12 15 30
400 1000
Input Torque (In.-Lb.)
B C D E
D
Horsepower HP
Horsepower HP
F 10 25
C A E 800
300
4 8 10 20
B D 600
E
6 200 15
A C
D 400
2 4 5 10
C 100
B B 200
2 5
A A
0 0 0 0 0 0
0 1000 2000 3000 0 1000 2000 3000
Pressure - PSI Pressure - PSI
MOTOR KW (HP) MOTOR KW (HP)
1.5(2) 2.2(3) 3.7(5) 5.6(7.5) 7.5(10) 11.2(15) 5.6(7.5) 7.5(10) 11.2(15) 14.9(20)
Compensator Setting Bar (PSI) Compensator Setting Bar (PSI)
PVP16 110.3 151.7 206.8 206.8 206.8 206.8 PVP33 151.7 186.2 206.8 206.8
FULL STROKE (1600) (2200) (3000) (3000) (3000) (3000) FULL STROKE (2200) (2700) (3000) (3000)
Pump Control Option “H” with PVP16 Pump Control Option “H” with PVP33
Horsepower Limiting Horsepower Limiting
Factory Compensator Settings Factory Compensator Settings
1.1(1.5)
By Cooler KW (HP)
B2
.75(1)
.60(.8)
.45(.6)
A
.37(.5)
.30(.4)
B1* B1
.22(.3)
Horsepower Removed
By Reservoir RESERVOIR SIZE LITERS (GALLONS) Heat removal is based on
18.9(5) 37.9(10) 75.7(20) 113.6(30) 151.4(40) static ambient air at 29.4oC
(85oF) and max. oil temperature
KW (HP) REMOVAL .15(.2) .28(.38) .43(.58) .51(.68) .60(.81)
of 57.2oC (135oF).
Operating Notes
• Jog the electric motor once and verify that the • It is recommended that every 4,000 operating hours
electric motor is rotating in the same direction as the or once a year, whichever occurs first, the filler/
arrow on the electric motor housing. If direction is breather cap and suction strainer should be replaced.
incorrect, reverse two of the three leads on a
3-phase electric motor.
Fluid Recommendations
• D & H-Pak power units are tested and relief valve Premium quality hydraulic oil with a viscosity range
is set at maximum pressure of the pump /motor between 150-250 SSU (30-50 cst.) at 100°F (38°C).
combination. Normal operating viscosity range between 80-1000 SSU
• V-Pak power units are tested and pressure control (17-180 cst.). Maximum start-up viscosity is 4000 SSU
valves are factory preset. If adjustments are needed, (1000 cst.).
follow the procedure below: Begin adjusting relief NOTE: Consult Parker when exceeding 160°F (71°C)
valve and pump compensator control valve to operation. Oil should have maximum anti-wear
increase pressure gradually. (NOTE: Always set relief properties, rust and oxidation treatment.
valve 250 PSI higher than pump compensator
pressure control valve or severe overheating will
occur.) Filtration
For maximum pump and system component life, the
• If pump fails to prime, vent pump discharge to
system should be protected from contamination at a
atmosphere to establish fluid flow.
level not to exceed 125 particles greater than 10 microns
• Reservoir temperature should not exceed 150°F. per milliliter of fluid. (SAE Class 4 / ISO 16/13.) Due to
System reliability and component service life will be the nature of variable displacement pumps, variations
reduced when system is operated at higher in pump inlet conditions, fluid acceleration losses,
temperature. system aeration, and duty cycle must be carefully
considered before specifying suction line filtration.
• Clean fluid = improved system reliability and longer Contact your Parker representative for assistance.
component service life, change filter elements
whenever filter indicators indicate a dirty element NOTE: For additional information refer to latest edition
condition. of Bulletin No. HY13-2600-550-xxx..
Dimensions*
Pump Mounting Adapter
G
A G A
DIA. D P B DIA. D P B
DIA. DIA. DIA. DIA.
DIA. DIA.
G
G
876631 SAE AA 56C 6.7 5.0 5.88 N/A 4.50 3.50 1.63 3/8-16 0.44 2.00 YES YES 1 3 lb.
876632 SAE AA 182TC/256TC 9.0 5.3 7.25 N/A 8.50 5.00 1.63 3/8-16 0.56 2.00 YES YES 1 4 lb.
876633 SAE A 56C 6.7 5.0 5.88 N/A 4.50 4.25 2.10 3/8-16 0.44 3.25 YES YES 1 4 lb.
876634 SAE A 182TC/256TC 9.0 5.3 7.25 N/A 8.50 5.00 2.10 3/8-16 0.56 3.25 YES YES 1 4 lb.
876635 SAE A 182TC/256TC 9.0 5.3 7.25 N/A 8.50 5.88 2.10 3/8-16 0.56 3.25 YES YES 1 5 lb.
875343 SAE B 182TC/256TC 11.4 9.0 7.25 10.25 8.50 5.75 2.88 1/2-13 0.53 4.00 YES NO 2 7 lb.
875344 SAE B 182TC/256TC 11.4 9.0 7.25 10.25 8.50 6.81 2.88 1/2-13 0.53 4.00 YES NO 2 8 lb.
876683 SAE B 182TC/256TC 9.0 8.8 7.25 N/A 8.50 6.38 2.88 1/2-13 0.53 4.00 NO YES 1 7 lb.
876684 SAE C 182TC/256TC 9.0 9.3 7.25 N/A 8.50 6.69 3.56 5/8-11 0.53 5.00 NO YES 1 20 lb.
NOTE: It is the responsibility of the user to check the listed dimensions to ensure suitability of mounting adapter with pump/coupling/motor combination.
Application Formulas
• 1 GPM at 1500 PSI = 1 HP (General Rule) • 1 HP = 42.4 BTU/Min.
• 1 Gallon = 231 Cubic Inches (3.7854 Liters) • 1 Gallon = 3.7854 Liters
• 1 Gallon Oil = 7.08 Lbs.
• 1 bar = 14.5 PSI
• 25.4mm = 1 Inch
GPM x PSI
HP =
1714 x Pump Efficiency
HP x 63025
Torque =
RPM
HP x 63025
RPM =
Torque
Motor Information
At 440V — 3-Phase Motor Draws 1.25 AMP/HP
At 220V — 3-Phase Motor Draws 2.5 AMP/HP
At 110V — Single Phase Motor Draws 10 AMP/HP