Professional Documents
Culture Documents
Пакер Тулз Каталог На Английском
Пакер Тулз Каталог На Английском
GENERAL
CATALOG
CONTENTS
1
PACKERS FOR HYDRAULIC FRACTURING AND TECHNOLOGICAL OPERATIONS
Overview
Packer PS is applied for fracture treatment performance, plugging operations, acid treatments, formations testing, casing string leakage revealing.
Technical specifications
Top anchor hydraulic
Bottom anchor mechanical
The way of installing rotatable
Pressure differential taken by packer 70 MPa
Max extension load 400 kN
Installation weight min-max 6-15 t
Max temperature of exploitation 176 °С
Sizes
*The upper / lower
Casing size, The range of The diameter of the Internal drift Packer Packer
Name thread. box-pin
mm (inch) applicability, mm calibrating rings, mm diameter, mm length, mm weight, kg
GOST 633-80
Packer PS-114/96/44-V-70GYA-К1- V60/V60 114 (4 1/2) 98…104 95,7 44,5 1575 50 60V/60V
Packer PS-127/102/44-V-70GYA-К1- V60/V60 127 (5) 104…115 102 44,5 1575 50 60V/60V
140 (5 1/2)
Packer PS-140/120/49-V-70GYA-К1- V60/V60 124…136 120,5 49 1870 80 60V/60V
146 (5 3/4)
Packer PS-168/142/60-V-70GYA-К1- V73/V73 168 ( 6 5/8 ) 145…154 142 60 1925 120 73V/73V
Packer PS-168/146/60-V-70GYA-К1- V73/V73 168 ( 6 5/8 ) 150…158 146 60 1925 120 73V/73V
Packer PS-245/205/100-V-70GYA-К1- 114/114 245 212…226 205 100 2510 400 114/114
Packer PS-245/210/100-V-70GYA-К1- 114/114 245 220…229 210 100 2510 400 114/114
* - the possibility of different types of thread manufacturing by the customer’s request
Constructional peculiarities
– equipped by bypass assembly that provides the opportunity to adjust pressure for unsetting ease as well as allows to conduct direct and back
cleaning out of annulus section of packer above;
– has got high abrasion resistance to proppant pumping while fracturing (up to 600 tons per one tripping operation);
– is equipped by spring elements in corrosion-resistant performance, that provides packer working capacity in corrosion environment (acid
treatments, acid fracture treatments and other operations);
– assembled on a mono well bore;
– direct influence of pumped out fluid to a hydraulic anchor is excluded that provides assured reset of rams into a transport position.
2
PACKERS FOR HYDRAULIC FRACTURING AND TECHNOLOGICAL OPERATIONS
Overview
PS-P packer is applied for fracture treatment performance, plugging operations, acid treatments, formations testing, casing string leakage
revealing.
Technical specifications
Top anchor hydraulic
Bottom anchor mechanical
The way of installing axial-type
Pressure differential taken by packer 70 MPa
Max extension load 400 kN
Installation weight min-max 6-15 t
Max temperature of exploitation 176 °С
Sizes
The diameter of Packer *The upper / lower Differential
Casing size, The range of Internal drift Packer
Name the calibrating length, thread. box-pin pressure, perceived
mm applicability, mm diameter, mm weight, kg
rings, mm mm GOST 633-80 by the packer, MPa
168
PS-168/136/60-О-70GYA-К1-V73/V73 140…148 136 60 2700 100 V73/V73* 70
(6 5/8 )
168
PS-168/142/60-О-70GYA-К1-V73/V73 145…156 142 60 2700 110 V73/V73* 70
(6 5/8 )
168
PS-168/146/60-О-70GYA-К1-V73/V73 (6 5/8 ) 150…157 146 60 2700 110 V73/V73* 70
178 ( 7 )
Constructional peculiarities
– equipped by bypass assembly that provides the opportunity to adjust pressure for unsetting ease as well as allows to conduct direct and back
cleaning out of annulus section of packer above;
– has got high abrasion resistance to proppant pumping while fracturing (up to 600 tons per one tripping operation);
– is equipped by spring elements in corrosion-resistant performance, that provides packer working capacity in corrosion environment (acid
treatments, acid fracture treatments and other operations);
– assembled on a mono well bore;
– direct influence of pumped out fluid to a hydraulic anchor is excluded that provides assured reset of rams into a transport position.
3
PACKERS FOR HYDRAULIC FRACTURING AND TECHNOLOGICAL OPERATIONS
Overview
Packer PS-MYA is applied for fracture treatment performance, plugging operations, acid treatments, formations testing, casing string leakage
revealing. Applied for injection wells exploitation.
Technical specifications
Top anchor mechanical
Bottom anchor mechanical
The way of installing rotatable
Pressure differential taken by packer 70 MPa
Max extension load 400 kN
Installation weight min-max 6-15 t
Max temperature of exploitation 175 °С
Sizes
The diameter of the *The upper / lower
Casing string size, The range of Internal drift Packer
Name calibrating rings, thread. box-pin
mm (inch) applicability, mm diameter, mm length, mm
mm GOST 633-80
140 (5 1/2) /
Packer PS-146/118/60- V-70MYA-K1-73/73 121...134 118 60 1930 73/73
146 (5 3/4)
Constructional peculiarities
– equipped by bypass assembly that provides the opportunity to adjust pressure for unsetting ease as well as allows to conduct direct and back
cleaning out of annulus section of packer above;
– has got high abrasion resistance to proppant pumping while fracturing (up to 600 tons per one tripping operation);
– is equipped by spring elements in corrosion-resistant performance, that provides packer working capacity in corrosion environment (acid
treatments, acid fracture treatments and other operations);
– assembled on a mono well bore.
4
PACKERS FOR PLUGGING AND TECHNOLOGICAL OPERATIONS
Overview
Packer PS-P is applied for plugging operations, acid treatments, formations testing, casing string leakage revealing.
Technical specifications
Top anchor hydraulic
Bottom anchor mechanical
The way of installing rotatable
Pressure differential taken by packer 35 MPa
Max extension load 400 kN
Installation weight min-max 12-16 t
Max temperature of exploitation 176 °С
Sizes
The diameter of Internal drift Packer *The upper / lower
Casing string size, The range of Packer
Name the calibrating diameter, length, thread. box-pin
mm (inch) applicability, mm weight, kg
rings, mm mm mm GOST 633-80
146 (5 ¾)
Packer PS- P140/116/44-V- 70GYA-К1-V73/V73 121..126 116 44 1650 80 V73/V73
140 (5 ½)
Packer PS- P146/122/60-V- 70GYA-К1-V73/V73 146 (5 ¾) 127…130 122,5 59…61 1600 75 V73/V73
Packer PS- P168/138/60-V- 70GYA-К1-V73/V73 168 (6 ⅝) 142…148 138 60 1720 100 V73/V73
Packer PS- P168/142/76-V- 70GYA-К1-V89/89 168 (6 ⅝) 145…150 142 76 1700 100 V89/89
Packer PS-P178/150/76-V- 70GYA-К1- V89/89 178 (7) 154…160 150 76 1700 100 V89/89
Constructional peculiarities
– increased ID;
– equipped by bypass assembly that provides the opportunity to adjust pressure for unsetting ease as well as allows to conduct direct and back
cleaning out of annulus section of packer above;
– is equipped by spring elements in corrosion-resistant performance, that provides packer working capacity in corrosion environment (acid
treatments, acid fracture treatments and other operations);
– assembled on a mono well bore.
5
PACKERS FOR TECHNOLOGICAL OPERATIONS
SERIES PSMO
Overview
Packer PS-MO is intended for pressure-tight intervals’ isolation of casing string hole and its protection from dynamic influence of working fluid
during different technological operations conducting.
Technical specifications
The way of installing axial-type
Pressure differential taken by packer 70 MPa
Max extension load 350 kN
Installation weight min-max 8-15 t
Max temperature of exploitation 176 °С
Sizes
The diameter of *The upper / lower thread.
Casing string size, The range of Internal drift Packer Packer weight,
Name the calibrating box-pin
mm (inch) applicability, mm diameter, mm length, mm kg
rings, mm GOST 633-80
146 (5 ½)
PS-M140/118/60-О-70К1-73V/89 121…134 118 60 2050 60 73V/89
146 (5 ¾)
168 (6 ⅝)
PS-М168/146/76-О-70К1-89/89 150…157 146 76 2200 90 89/89
178 (7)
Constructional peculiarities
– is equipped by spring elements in corrosion-resistant performance, that provides packer working capacity in corrosion environment (acid
treatments, acid fracture treatments and other operations);
– assembled on a mono well bore;
– high repairability.
6
PACKERS FOR TECHNOLOGICAL OPERATIONS
Overview
Packer PS-1M GYA is intended for pressure-tight intervals’ isolation of casing string hole and its protection from dynamic influence of working fluid
during different technological operations conducting.
Technical specifications
The way of installing axial-type
Differential pressure 70 MPa
The maximum load tension 300 kN
Installation weight min-max 6-12 t
Maximum operating temperature 120/150 °С
K1 Carbon dioxide content in well
Corrosion-resistant performance production not more than 10%
Sizes
The diameter of *The upper / lower thread.
Casing string size, The range of Internal drift Packer Packer weight,
Name the calibrating box-pin
mm (inch) applicability, mm diameter, mm length, mm kg
rings, mm GOST 633-80
168 (6 ⅝)
PS-1М 168/146/76-О-70GYA-К1-89/89 150…160 146±0,1 75±1 1850 150 89/89**
178 (7)
PS-1М 178/150/76-О-70GYA-К1-89/89 178 (7) 154…166 150 75±1 1850 160 89/89**
*- the possibility of different types of thread manufacturing by the customer’s request
Constructional peculiarities
– is equipped by spring elements in corrosion-resistant performance, that provides packer working capacity in corrosion environment (acid
treatments, acid fracture treatments and other operations);
– assembled on a mono well bore;
– high repairability.
7
SERVICE PACKERS
SERIES PSM
Overview
Packer PS-M is applied for plugging operations, acid treatments, formations testing, casing string leakage revealing, different fluids pumping into
the formation.
Technical specifications
The way of installing rotatable
Pressure differential taken by packer 35 MPa
Max extension load 200 kN
Installation weight min-max 8-15 t
Max temperature of exploitation 120 °С
Sizes
The diameter of *The upper / lower thread.
Casing string size, The range of Internal drift Packer Packer
Name the calibrating box-pin
mm (inch) applicability, mm diameter, mm length, mm weight, kg
rings, mm GOST 633-80
Constructional peculiarities
– equipped by bypass assembly that provides the opportunity to adjust pressure for unsetting ease as well as allows to conduct direct and back
cleaning out of annulus section of packer above;
– has got high abrasion resistance to proppant pumping while fracturing (up to 600 tons per one tripping operation);
– is equipped by spring elements in corrosion-resistant performance, that provides packer working capacity in corrosion environment (acid
treatments, acid fracture treatments and other operations).
8
SELECTIVE PACKERS
SERIES PSS
Overview
Packer PS-S applied for fracture treatment performance, plugging operations, acid
treatments, formations testing, casing string leakage revealing.
That is a retrievable tool with two assemblies being fixed in that position into production string
as well as with two seal assemblies between of which there a section of tubing-annulus
connection. It is equipped additionally with back ball (stabbing) valve for shutting down of
tubing side below and above the intervals of its installing.
Technical specifications
The way of installing rotatable
Pressure differential taken by packer 70 MPa
Max extension load 400 kN
Installation weight min-max 11-18 t
Max temperature of exploitation 176 °С
Sizes
PS-146S/121/49-V- PS-168S/142/60-V- PS-178S/150/60-V-
70 GYA-К1 89/60V 70 GYA-К1 89/73V 70 GYA-К1 89/73V
Casing string size, mm
146 (5 3/4) 168 (6 5/8) 178 (7)
(inch)
The range of applicability,
124…136 145…155 154…164
mm
The diameter of the
121 142 150
calibrating rings, mm
Internal drift diameter,
49 60 60
mm
Packer length, mm 5000 5000 5000
Constructional peculiarities
– top packer as well as bottom packer are equipped by bypass assembly that provides the
opportunity to adjust pressure for unsetting ease;
– has got high abrasion resistance to proppant pumping while fracturing (up to 600 tons per
one tripping operation);
– is equipped by spring elements in corrosion-resistant performance, that provides packer
working capacity in corrosion environment (acid treatments, acid fracture treatments and
other operations);
– direct influence of pumped out fluid to a hydraulic anchor is excluded that provides assured
reset of rams into a transport position;
– packer PS-S allows to influence the formation selectively;
– packer PS-S is the tool for passing through allowing to pump through it volumes of fluid
and to run into the hole smoothly perforators and logging tools.
9
BACK BALL VALVE, TYPE OSHK
Overview
Back ball valve is intended for shutting down of tubing side to exclude necessity of well killing.
Sizes
Outside diameter, Run-in clearance, Length, Weight, The maximum Upper / lower
Name
mm mm mm kg load, kN connecting thread
Constructional peculiarities
– ball valve is opened and closed by ½ rotation of tubing turning;
– back ball valve construction allows possibility of its opening and closure by right turning as well as by left turning;
– for changeover of direction of closure/ opening it is enough to turn 180 degrees about the ball of back ball valve;
– application with any downhole equipment is possible.
10
PACKERS FOR SEPARATE WATER INJECTION OPERATIONS AND PRESSURE MAINTENANCE
Overview
Press-on packer PSN assembled with hydraulic anchor is intended for two intervals separation of production casing of the well with one or some
reservoirs.
Sizes
Packer Packer Packer Packer
PSN-178/152/76 PSN-168/142/76 PSN-146/121/60 PSN-140/116/60-
-70-К1- 89/89 -70-К1- 89/89 -70-К1-V73/V73 70-К1-V73/V73
Tubing string outer diameter, mm 177,8 168 146 140
Tubing string internal diameter, mm 154…164 145 …154 124 …136 119 …133
*Upper connecting thread, GOST 633-80 Oil-well tubing 89 Oil-well tubing 89 Oil-well tubing 73V Oil-well tubing 73
*Lower connecting thread, GOST 633-80 Oil-well tubing 89 Oil-well tubing 89 Oil-well tubing 89 Oil-well tubing 89
Constructional peculiarities
Press-on packer PSN assembled with hydraulic anchor is applied in injection and production wells at dual exploitation of some reservoirs of one
well, also in multipacker assemblies as top cut-off packer, activated by weight applying down the hole or to the packer located below.
11
PACKERS FOR SEPARATE WATER INJECTION OPERATIONS AND PRESSURE MAINTENANCE
SERIES PSNMYA
Overview
Packer PSN-MYA is intended for two intervals separation of production casing of the well with one or some reservoirs. It is applied in injection and
production wells at dual injection operations and dual production operations as well as it is applied in multipacker assemblies as top cut-off device.
Technical specifications
The way of installing weight applying
Pressure differential taken by packer 35 MPa
Max extension load 400 kN
Installation weight min-max 6-15 t
Max temperature of exploitation 176 °С
Sizes
Casing string size, The range of The diameter of the Internal drift Length, *The upper / lower thread.
Name
mm (inch) applicability, mm calibrating rings, mm diameter, mm mm box-pin GOST 633-80
Constructional peculiarities
– shear pins’ absence providing possibility of multiple application per one tripping operation;
– is equipped by spring elements in corrosion-resistant performance, that provides packer working capacity in corrosion environment (acid
treatments, acid fracture treatments and other operations);
– is equipped by bypass assembly that provides the opportunity to adjust pressure for unsetting ease as well as allows to conduct direct and back
cleaning out of annulus section of packer above.
12
PACKERS FOR WELLS WITH ESP OUTFIT
SERIES PSK
Overview
Packer PS-K is applied for intervals isolation of production casing during exploitation of the wells with ESP with isolation of production casing
leaking section located above packer setting place. Packer PS-K setting and unsetting into the well is made by standard operations with tubing
string (up-and-down motions) with pressure change making while setting and equalization of pressure at unsetting.
Technical specifications
The way of installing axial-type
Pressure differential taken by packer 35 MPa
Max extension load 200 kN
Installation weight min-max 6-16 t
Max temperature of exploitation 120 °С
Sizes
Casing string size, The range of The diameter of the Internal drift Length, *The upper / lower thread.
Name
mm (inch) applicability, mm calibrating rings, mm diameter, mm mm box-pin GOST 633-80
Constructional peculiarities
– possibility of cable run of ESP without integrity damage of cable and cable coupler;
– availability of two injections ports providing the opportunity of chemicals loading to ESP and gas withdrawal from below-packer section;
– possibility of wellhead cable hermetic sealing assembly pressure testing;
– possibility of packer PS-K pressure testing in pressure-tight section of production string;
– equipment of multiple application per one tripping operation;
– is equipped by spring elements in corrosion-resistant performance, that provides packer working capacity in corrosion environment (acid
treatments, acid fracture treatments and other operations).
13
ANCHOR EQUIPMENT
Overview
Hydraulic anchor GYA is applied for packers’ setting and other downhole equipment settling in production casing string while conducting of
fracturing, plugging operations, acid treatment, formation testing, casing string leakage revealing and wells’ exploitating. It is a retrievable
tool with locking assembly into production string.
Hydraulic anchor GYA is the tool for passing through allowing to pump through it volumes of fluid and to run into the hole smoothly
perforators and logging tools.
Technical specifications
Pressure differential taken by packer 70 MPa
Max extension load 400 kN
Max temperature of exploitation 176 °С
Sizes
Internal drift The diameter of *Upper / lower connecting
Casing string size, The range of Length, Weight,
Name diameter, the calibrating thread, box in accordance
mm (inch) applicability, mm mm no more, kg
mm rings with GOST 633-80
Hydraulic anchor
140 119…133 56 116 380 20 73 / 73V
GYA-140/116/56- 70К1-73/73V
Hydraulic anchor
140/146 121…133 58 118 390 20 73V / 73
GYA-140/118/58- 70К1-73/73
Hydraulic anchor
146 125…136 60 121 380 20 73В / 73V
GYA-146/121/60- 70К1-73V/73V
Hydraulic anchor
168 ( 6 5/8 ) 145…154 68 140 425 25 89V / 89
GYA-168/140/68- 70К1-89V/89
Hydraulic anchor
168 ( 6 5/8 ) 145…155 77 142 400 25 89 / V89
GYA-168/142/77- 70К1-89/V89
Hydraulic anchor
178 ( 7 ) 151…164 77 148 400 25 89 / V89
GYA-178/148/77- 70К1-89/V89
Hydraulic anchor
178 ( 7 ) 154…166 76 150 400 30 89V / 89
GYA-178/150/76- 70К1-89V/89
- the possibility of different types of thread manufacturing by the customer’s request
Constructional peculiarities
– hydraulic anchor GYA is equipped by spring elements in corrosion-resistant performance, that provides packer working capacity in
corrosion environment (acid treatments, acid fracture treatments and other operations).
14
MECHANICAL STRING DISCONNECTOR
Overview
Mechanical string disconnector is intended for connection and disconnection of flexible pressure-tight joint of tubing string with packer and
anchor equipment left self-contained in production casing as well as for its retrieving.
Technical specifications
Disconnection turn of 1/4 tubing string
Differential pressure 70 MPa
The maximum load tension 320 kN
Maximum operating temperature 176 °С
Sizes
*Upper *Lower
Length,
Name OD, mm ID, mm Weight, kg connecting thread, box connecting thread nipple
mm
GOST 633-80 GOST 633-80
Constructional peculiarities
– separation does not require the use of balls;
– short compact design;
– switch can be assembled as a discharge for cutting and for cutting by means of a tension;
– disconnectors allows for the re-connection automatically when the application loads the landing;
– adjustable cutting-off force;
– right hand and Left hand.
15
HYDRAULIC STRING DISCONNECTOR
Overview
Hydraulic disconnector RG-95.60.50-K1-73/73V is intended to release tubing string from the
downhole equipment or retrievable object if the effort made by the lift is not sufficient to eliminate
the tubing being stuck or it is necessary to leave the equipment that is below string disconnector
autonomously into the well.
Technical specifications
Differential pressure, MPa 70
Maximum tensile load before disengaging, kN 830
Maximum operating temperature, °С 150
Outer diameter per disconnector body, mm 95
Outer diameter per fishing liner, mm 105
Upper connecting thread NKT 73
Lower connecting thread NKT 73V
Internal diameter before disconnection, mm 50
Internal diameter after disconnection, mm 60
Disconnector’s length, mm 715
Pins quantity in disconnector, pcs. 12
Pin’s cutting pressure, MPa 1
Activation plug diameter, mm 56
Activation plug valve pins cutting of pressure, MPa 20
Catcher’s outside diameter, mm 122,5
Catcher’s length, mm 740
Catcher’s connecting thread * NKT 89
Maximum tensile load of catcher, kN 450
*- the possibility of different types of thread manufacturing by the customer’s request
Constructional peculiarities
– splined connection ensures the transmission of torque;
– disconnection occurs due to the ball dropping or activation plug and pumping into the disconnector
seat;
– possibility of regulating the activation pressure;
– removing with a LRG catcher or standard fishing tool (overshot or spear); adjustable cutting-off
force;
– possibility of disconnecting by ¼ right rotation of the catcher from the disconnector.
16
CONTAINERS FOR SELFPOWERED GEOPHYSICAL INSTRUMENTS
Overview
The container for self-powered geophysical devices is intended for mounting and grid feeling of one or two converters in layout on tubing
string.
Technical specifications
Differential pressure 70 MPa
Max extension load 400 kN
Maximum operating temperature 176 °С
Sizes
Min inside diameter of *Upper / lower
Name Internal drift diameter, mm the production column, Length, mm connection thread according to
mm GOST 633-80
Constructional peculiarities
– mounting and grid feeling of one or two converters in layout on tubing string;
– has a high wear resistance to pumping proppant at fracturing (up to 600 t per one tripping operation).
17
PILOT MILLING CUTTER, TYPE FTVP
Overview
Pilot milling cutter type FTVP is intended for milling a cement stone in cased well, metal objects with a hollow form, upper ends of tubing
string, drilling and casing pipes in order to ensure trapping with a fishing tool.
Sizes
Diameter with the Range of applicability,
Name Diameter of the pilot, mm Pilot length, no more mm Connecting thread
reinforcement, mm mm
Constructional peculiarities
– the presence of the pilot in the design of the cutter allows you to center it relative to the center of the milled object;
– it is possible to make milling in aggressive environments and in difficult conditions where high durability of the tool is required;
– flushing channels are provided for supplying flushing and cooling liquid to the milling zone.
18
CONICAL MILLING CUTTER TYPE FKK
Overview
Conical milling cutter type FKK is intended for milling damaged sections (borehole collapse) of pipe columns, as well as for cutting
windows in casing strings in order to spud a new bore hole during repair and recovery operations in wells.
Sizes
Name Diameter, mm Length, mm The range of applicability, mm Connecting thread
Constructional peculiarities
– it is possible to make milling in aggressive environments and in difficult conditions where high durability of the tool is required;
– flushing channels are provided for the supply of flushing and cooling liquid to the milling zone.
19
HOLE ANNULUS MILLING SYSTEM
Sizes
Name Name D, mm Thread
Sizes
Name Name D, mm d, mm Thread
Sizes
Outer Inside The number The outer diameter The inside diameter
Connection thread
Name Name diameter, diameter, of grooves of cutting structure, of cutting structure,
FJ-WP
mm mm X, pcs mm mm
Radial mill FK 121х8 PP-95 121 105 3…,6 Request Request 4 3/4"
Radial mill FK 136х9 PP-ХХ 136 118 3…,6 Request Request 5 3/8"
Radial mill FK 146х10 PP-ХХ 146 126 3…,6 Request Request 5 1/2"
Radial mill FK 146х10 PP-ХХ 146 126 3…,6 Request Request 5 1/2"
Constructional peculiarities
– the use of a special thread that allows you to transmit high torque when using a thin-walled wash pipe;
– quick replacement of worn-out cutter by quick screwing-unscrewing, without the use of welding.
20
STABILIZER
Overview
The stabilizer is intended for centering drill string, drill bit, milling tool to improve working conditions, as well
as to reduce the curvature of the well .Stabilizers are available with straight and spiral blades.
Sizes
Length, Top / bottom connecting thread.
Name Diameter, mm
no more, mm tool- joint thread or tubing string
21
FACE MILLING CUTTER, TYPE FT
Overview
Face milling cutter is intended for the destruction of metal objects cement stone and cemented metal objects throughout the section of
wells during repair and recovery operations in oil and gas wells, it is well established in the milling of ports with balls and without in the
layout multistage fracturing.
Sizes
Outer Length L, Weight, Connection
Name
diameter D, mm mm kg thread
Constructional peculiarities
– aggressive heavy front cutting structure;
– cutting structure of the rear part of the milling cutter;
– elongated gauge section.
22
FISHING TOOLS
Overview
Twin overshot type OVSH is intended to catch and retrieve the CT pipe, the cylindrical objects left in the well as a
consequence of sticking or other reasons.
Technical specifications
OVSH – 54PT OVSH – 57PT OVSH – 68PT
Diameter, D mm 54 57 68
Constructional peculiarities
– the ability to flush during running-in and fishing operations;
– uniform distribution of gripping load on two baskets;
– the increased length of the overshot allows you to grip the undeformed section of the CT pipe.
23
FISHING TOOLS
Overview
The catcher type LRG is intended for catching the inner surface of the standard GS neck and retrieve the tool left in the well due to stuck or other
reasons.
Technical specifications
LRG– 45 LRG-54 LRG-73
Fishing neck 2” GS 2 ½” GS 3” GS
Diameter, D mm 45 54 73
Constructional peculiarities
– the ability to flush during running in and fishing operations;
– the possibility of release, in case the generate force with the coiled tubing installation is not sufficient.
24
FISHING TOOLS
Sizes
Name Outer diameter of the sub, mm Outer diameter of the body, mm Length, mm Connection thread, GOST Р 50864-96* Weight, kg
CABLE CATCHERS
SPIRAL CABLE CATCHER Overview
Cable catchers are intended for retrieving broken off ropes, cables and wires from
tubing string with diameters of 60, 73, 89 mm. Cable catcher running in the well on CT
pipe when working with coiled tubing units or on a rope.
CABLE CATCHER PIKE’S MOUTH DOUBLE CABLE CATCHER PIKE’S MOUTH TRIPLE
Sizes
Nominal diameter Cable catcher length, Cable catcher diameter, Weight, Connection thread,
Name
of the tubing string, mm not more than, mm not more than, mm no more than, kg GOST Р 50864-96*
Constructional peculiarities
– simple design;
– high maintainability.
25
EQUIPMENT FOR COILED TUBING
WASHJETTING SHOECONTAINER
Overview
Wash-jetting shoe-container for coiled tubing is intended for fastening and reliable retention of autonomous geophysical devices in the arrangement
on CT pipe.
Technical specifications
Differential pressure 35 MPa
The maximum load tension 150 kN
Maximum operating temperature 120 °С
Sizes
Name Internal drift diameter, mm Length, mm Connection thread
Constructional peculiarities
– fastening and reliable retention of the converter in the layout on CT;
– has an internal drift channel for flushing.
Overview
Spherical wash-jetting shoe-container is intended for washing sand-proppant plugs with the possibility of installing autonomous geophysical
devices.
Technical specifications
Differential pressure 35 MPa
The maximum load tension 150 kN
Maximum operating temperature 120 °С
Sizes
Outside diameter, Diameter of the pocket Converter length, Length L, Connection
Name
D, mm for the converter d, mm L, mm mm thread
Constructional peculiarities
– the geophysical instrument is placed in a groove isolated from the flushing channel.
26
EQUIPMENT FOR COILED TUBING
Overview
Conical wash-jetting shoe-container is intended for washing sand-proppant plugs with the ability to install autonomous geophysical instruments.
Technical specifications
Differential pressure 35 MPa
The maximum load tension 150 kN
Maximum operating temperature 120 °С
Sizes
Outer Diameter of the pocket Converter length Length L, Connection
Name
diameter D, mm for the converter d, mm L, mm mm thread
Constructional peculiarities
– the geophysical instrument is placed in a groove isolated from the flushing channel;
– has a front bevelled part, which allows the mechanical destruction of the obstacle.
27
EQUIPMENT FOR COILED TUBING
Overview
CT pipe reeling electric mechanism EMNT-01 is intended for CT pipe reeling/
unreeling with a diameter up to 44.45 mm of the reeling node (drum) of coiled
tubing units when replacing, repairing, or rewinding the pipe.
Technical specifications
Nominal pipe diameter, mm up 44.45
Drive Electric
Power, kW:
- drum drive 11
- level wind drive 3.7
Torque, Nm
- drum drive 22000
- level wind drive 900
Dimensions, mm, no more:
- height 2860
- width 3640
- length 2500
Unit weight, kg, no more than: 2500
Rotational speed of drum 4,8 turn/min
Constructional peculiarities
– equipped with electric drive;
– frequency control of drum drives and lay down machine for smooth and uniform
reeling;
– removable lay down machine;
– equipped with a mechanical counter of the length of reeling up pipe;
– remote control;
– water-proof version of the control panel.
28
EQUIPMENT FOR COILED TUBING
CT CROSSOVER
Overview
CT crossover is intended for connecting threaded elements with different diameters
or threads, as well as for equipment affixing having threaded ends of the indicated
designations.
Technical specifications
The outside diameter The inside diameter
Thread mark
d, mm d, mm
29
EQUIPMENT FOR COILED TUBING
CIRCULATING SUB
Overview
Circulation sub is intended to create a hydrodynamic connection with the annular space of the tubing string, the production column and the coiled tubing in wells with low
reservoir pressure. It is used for milling, creating a constant pressure drop of the nitrated liquid above the screw downhole motor.
Sizes
Name Outer diameter, D, mm Inner diameter, d mm Coupling thread Nipple thread Length L, mm Weight, kg
Constructional peculiarities
– replaceable fittings;
– simple design.
30
EQUIPMENT FOR COILED TUBING
Overview
Crossover sub for coiled tubing (Roller) is intended for the connection of the CT pipe with a downhole tool.
Technical specifications
The maximum load tension 60 kN
Maximum operating temperature 120 °С
Sizes
Nominal pipe Wall thickness Outer Internal Length L, Connection
Name
diameter, mm of pipe, mm diameter D, mm diameter, mm mm thread
Constructional peculiarities
– does not require trimming the seam of the pipe installation.
31
EQUIPMENT FOR COILED TUBING
Overview
Crossover sub for coiled tubing (roller) is intended for the connection of the CT pipe with a downhole tool. Equipped
with two O-rings, ensuring a hermetic connection with coiled tubing.
Technical specifications
Differential pressure 35 MPa
The maximum load tension 60 kN
Maximum operating temperature 120 °С
Sizes
Nominal pipe Wall thickness Outer diameter Internal Length L, Connection
Name
diameter, mm of pipe, mm D, mm diameter, mm mm thread
32
EQUIPMENT FOR COILED TUBING
Overview
Crossover sub for coiled tubing (connector) is intended to connect the CT pipe with a downhole tool.
Technical specifications
Differential pressure 35 MPa
The maximum load tension 200 kN
Maximum operating temperature 120 °С
Sizes
Nominal pipe Outer Internal Length L, Connection Weight,
Name
diameter, mm diameter D, mm diameter, mm mm thread kg
Overview
The device is intended for mounting and dismounting the connector.
Sizes
Pipe diameter, Number of Length L, Connection
Name
mm mounting screws mm thread
33
EQUIPMENT FOR COILED TUBING
Technical specifications
Differential pressure 35 MPa
The maximum load tension 250 kN
Maximum operating temperature 120 °С
Sizes
Nominal pipe Outer Internal Length L, Connection Weight,
Name
diameter, mm diameter D, mm diameter, mm mm thread kg
Overview
Crossover sub for coiled tubing (connector) is intended for connection of a CT pipe with a downhole tool.
Sizes
Pipe diameter, Number of Length L, Connection
Name
mm mounting screws mm thread
34
EQUIPMENT FOR COILED TUBING
Overview
The basket connector is intended for CT pipe connecting with the downhole tool
Technical specifications
Differential pressure 35 MPa
The maximum load tension 200 kN
Maximum operating temperature 120 °С
Sizes
Nominal pipe Outer Internal Length L, Connection Weight,
Name
diameter, mm diameter D, mm diameter, mm mm thread kg
Basket connector KTS-54/38,1 38,1 54 25,5 290 М 42х2 1 ½ АММТ NKT 42 No more 2.5
Basket connector KTS-57/44.45 44, 45 57 22 330 М 42х2 1 ½ АММТ Z-45 NKT 42 No more 2.5
Constructional peculiarities
– simplicity and reliability of construction;
– does not require a device for installation.
35
EQUIPMENT FOR COILED TUBING
Overview
Check valve type KO is intended to prevent the flow of fluid in CT pipe when the injection is stopped.
Technical specifications
КО – 38TS КО – 45TS
Diameter, D mm 38.1 45
Connection thread М 30 х 2 М 30 х 2
Constructional peculiarities
– as a locking element is used carbide pair «ball-saddle»;
– the pusher and spring are made of corrosion-resistant materials.
36
EQUIPMENT FOR COILED TUBING
Overview
Flap valve type KOS is intended to prevent the flow of fluid in CT pipe when the injection is stopped.
Technical specifications
KOS-8 KOS-45 KOS-54 KOS-57 KOS-73 KOS-78
Nominal diameter of tubing string, mm 60; 73; 89 60; 73 89 73; 89 89; 102; 114 102; 114 102; 114
Diameter D, mm 38,1 45 54 57 73 78
Constructional peculiarities
– double valve;
– the possibility of pumping the ball to activate the below equipment;
– valve elements are made of corrosion-resistant materials;
– the possibility of acid treatments.
37
EQUIPMENT FOR COILED TUBING
Overview
Shear sleeve type MS is intended for secondary release of CT pipe from the downhole equipment or retrievable subject, in the case of sticking of
downstream equipment.
Technical specifications
MS-38PT MS-45PT MS-54PT MS-54/25PT
Sleeve length, L mm, not more than 176 176 176 265
Connection thread М 30 × 2 М 42 × 2
Constructional peculiarities
– simplicity and reliability of the design;
– ability to control the cutting force (from 1 to 8 tons).
38
EQUIPMENT FOR COILED TUBING
Overview
Cylinder impression tool type PT is intended to determine the position of the emergency tool or equipment, as well as to determine the nature of
the nature of breakage of columns in the well, by obtaining a print on the face surface.
Sizes
Outer diameter Length L, Weight,
Name Connecting thread
D, mm mm no more, kg
Constructional peculiarities
– reliable fastening of the lead part;
– has a through channel for flushing.
39
EQUIPMENT FOR COILED TUBING
Overview
Drift mandrel is intended for tubing string gaging. Has a through channel for flushing.
Sizes
Diameter of flushing
Name Length L, mm Diameter D, mm Weight, kg Connecting thread
hole, mm
Overview
The wash-jetting shoe for drift mandrel is intended to create directed jets of fluid, capable of destroying the counter-surface of the
obstacles in the case of washing in the gaging tubing string.
Sizes
Diameter of flushing
Name Length L, mm Diameter D, mm Weight, kg Connecting thread
hole, mm
40
EQUIPMENT FOR COILED TUBING
Sizes
Outer diameter Number Diameter Length L,
Name Connecting thread
D, mm of holes, pcs. of holes, mm mm
Constructional peculiarities
– it has one central and 4 side holes;
– simplicity and reliability of the design.
41
EQUIPMENT FOR COILED TUBING
Technical specifications
Wash-jetting shoe Wash-jetting shoe
D38,1-М30х2 D44-М30х2
Internal diameter, mm 4, 5, 6 4, 5, 6
Connecting threads М 30 x 2
Constructional peculiarities
– wash-jetting shoe equipped with replaceable wear- resistant hydro-monitor nozzles of different diameters;
– wash-jetting shoe is protected from the action of the reverse jet by a wear-resistant fairing.
42
EQUIPMENT FOR COILED TUBING
NOZZLE SPHERE
Overview
Nozzle-sphere is intended for washing wells with low reservoir pressure.
Sizes
Outer diameter Number of holes, Diameter of holes, Length L,
Name Connecting thread
D, mm pcs. mm mm
Constructional peculiarities
– has one central and 4 side holes, directed upwards, creating a vortex flow;
– simplicity and reliability of the design.
43
EQUIPMENT FOR COILED TUBING
Overview
Conical wash-jetting shoe is intended for washover and restoring the bottom of a well.
Sizes
Outer diameter Number of holes, Diameter of side holes, Diamet er of central Length L,
Name Connecting thread
D, mm pcs. mm holes, mm mm
Constructional peculiarities
– has a front bevelled part, which enables the mechanical destruction of the obstacle;
– has one central and 3 lateral openings.
44
EQUIPMENT FOR COILED TUBING
Overview
The special nozzle is intended for opening ports and circulation sleeves in multi-stage hydraulic fracturing
assembly.
Sizes
Name D, mm d, mm d1, mm D1, mm L, mm Weight, kg Connecting thread
Constructional peculiarities
– the possibility of washing the well from sand-proppant plugs and activation of the hydraulic fracturing
sleeve per one tripping operation;
– no central channel, side channels are directed up and down.
45
EQUIPMENT FOR COILED TUBING
Overview
The hydraulic disconnector, type RG is intended to release the coiled tubing (pipe) from the downhole
equipment or recoverable object, if the force, developed by the CT unit, is not sufficient to eliminate pipe
sticking.
Technical specifications
RG-45D RG- 54D
Shear pressure of the pins after ball install on seat, MPa, not more 18 15
Constructional peculiarities
– shaped connection provides transmission of torque;
– disconnecting occurs due to the discharge of the ball and pumping it into the saddle;
– the possibility of regulating the activation pressure.
46
EQUIPMENT FOR COILED TUBING
Overview
The hydraulic disconnector type SHP is intended for CT pipe release from the downhole equipment or retrievable item, if the effort developed by CT
unit is not sufficient to eliminate pipe sticking. Hydraulic disconnector bottom, type SHP has an internal profile of the fishing neck, type GS.
Technical specifications
RG-54SHP RG- 57SHP RG-73SHP
Constructional peculiarities
– shaped connection provides transmission of torque;
– disconnecting occurs due to the discharge of the ball and pumping it into the saddle;
– possibility of regulation of activation pressure;
– fitted with fishing neck type GS, which allows the capture of a standard fishing tool after disconnection.
47
EQUIPMENT FOR COILED TUBING
Overview
The motorhead assembly was designed due to manufacturing demand for compact equipment of increased operational reliability, being
an integral part of the bottom-hole assembly. It includes a double reverse flap valve, a hydraulic disconnector and a circulation valve. The
compact design reduces the total length of the tool by 30% in comparison with the use of conventional individual assemblies.
Technical specifications
Параметры KNDМ-54 KNDМ-57 KNDМ-73
48
EQUIPMENT FOR COILED TUBING
TOOL FOR WORKING WITH CT UNITS AND CABLE MACHINERY RIGID STABILIZER
Overview
Rigid stabilizer, is designed for centering of the downhole equipment and to stabilize the hydraulic bottomhole motors in the tubing string.
Rigid stabilizer is lowered into the well with coiled tubing.
Sizes
Nominal diameter of the Diameter Length Diameter of the Weight,
Name Connecting thread
tubing string, mm D, mm L, mm inner hole, mm kg
49
EQUIPMENT FOR COILED TUBING
PERFORATOR TYPE P
Overview
Perforator, type P is a special tool intended for cutting through holes in the production string.
Sizes
Outer diameter Diameter of the Length L, Number of
Name Connecting thread
D, mm nozzle, mm mm perforating holes
P40х3х3х120-М36х2 PT 40 3 3
Constructional peculiarities
– equipped with three carbide hydro-monitor nozzles;
– simple design.
50
EQUIPMENT FOR COILED TUBING
PERFORATOR, TYPE P2
Overview
Perforator type P2 is a special tool intended for cutting holes in the production string.
Sizes
Outer diameter Diameter of the Number of
Name Length L, mm Connecting thread
D, mm nozzle, mm perforating holes
Constructional peculiarities
– equipped with two nozzles. The valves are intended for descent with rinsing and subsequent
shutdown or without circulation;
– equipped with three hard-alloy nozzles;
– equipped with the circulation sub-device for the removal of abrasive after the hydro sandblasting
perforation.
51
EQUIPMENT FOR COILED TUBING
Sizes
Outer Drift Hardness Diameter Operating Diameter of the ball Diameter
Name diameter D, diameter, of carbide nozzle of carbide nozzle, temperature, °С, of activation of the of the wash activation
mm mm HRA mm no more than perforator, mm ball, mm
Constructional peculiarities
– equipped with three hard-alloy nozzles;
– equipped with a circulation sub-device for the removal of abrasive after the hydro sandblasting perforation;
– prior to activation of the perforator, it is possible to flush and control the pressure below 70 MPa below the equipment;
– maximum tensile load - 200 kN.
52
EQUIPMENT FOR COILED TUBING
Overview
Device for CT emergency pulling-out (Elevator) is intended to pulling-out and connect above the wellhead of an emergency or damaged coiled
tubing when operating with CT units.
Technical specifications
19,10
25,4
CT diameter, mm 33,5
38,1
44,45
Operating Lifting capacity, kN 160
Overall diameter (by body), mm 160
Overall diameter (by pins), mm 270
Weight, kg, no more than 12
53
EQUIPMENT FOR COILED TUBING
LUBRICATOR
Overview
The lubricator is used for the formation of the seal chamber to input the tool into the oil well and pulling it out during operations performed using coiled tubing.
Sizes
Name Length, L mm Connecting thread Drift diameter
54
EQUIPMENT FOR COILED TUBING
Overview
Cable head, type KN is intended for mechanical and electrical connection of geophysical equipment with an
armored geophysical cable which is located in the coiled tubing.
Sizes
Length L,
Name Connecting thread Outer diameter D, mm Weight, kg
mm
Constructional peculiarities
– equipped with three swivel joints;
– equipped with three electric lines;
– the maximum pressure is 70 MPa;
– maximum temperature - 120 °C;
– the maximum voltage is 500 V;
– maximum current 7 A;
– maximum tensile load - 30 kN.
55
EQUIPMENT FOR COILED TUBING
Overview
The cable thimble KN-GNKT-44GK PT is intended for connection of coiled tubing with logging instruments during geophysical surveys. Cable lug
for coiled tubing, specially designed for electrical and mechanical connection, single-core carrying geophysical cable, stored in coiled tubing, to a
logging tool.
Technical specifications
Material Steel 40KH Steel 40KHN Steel 12KH18Н10Т
Connecting threads, GOST 16093-2004 М 30х2 (top) М 33х1,5 (bottom) М 30х2 (plugs)
Outside diameter D, mm 44
Maximum current, A 7
Tensile load, kN 30
56
EQUIPMENT FOR COILED TUBING
Overview
The cable sealer GK-GNKT PT is intended to connect the ground part of the geophysical equipment to the coiled tubing with a cable during geophysical surveys using a coiled
tubing unit.
Technical specifications
Maximum working pressure, mPa 70
Nominal diameter 2”
Connection thread SPM 2”
Length, mm 167
Weight no more, kg 5
57
EQUIPMENT FOR COILED TUBING
Overview
The cable geophysical head GKG-3x7x500-M is intended to connect the ground part of geophysical equipment to the coiled tubing with a cable during geophysical surveys
using a coiled tubing unit.
Technical specifications
Maximum working pressure, MPa 70
Nominal diameter 2”
The maximum voltage, V 500
Maximum current, A 7
Number of current leads, pcs. 3
Length, mm 360
Weight no more, kg 20
58
WELLHEAD EQUIPMENT
FRAC WELLHEAD
Overview
Frac wellhead is a assembly of elements for well head piping, assembled into one product.
It’s intended for hanging of the tubing string and packer assembly, sealing the well-head
and ensuring the pumping process of working fluids and mixtures applied within fracturing.
Technical specifications
Set height, no more than, mm 2500
Threaded connection of the hanging nozzle, GOST 633-80 NKT 89
Threaded connection of the lifting sub, GOST 633-80 NKT 89
Dimensions of the flange for connection to the well
– diameter of the flange, mm 395
– number of holes for studs, pcs. 12
– average diameter under the sealing groove, mm 211.1
Operating pressure, MPa 70
Lifting capacity 80 000
Weight, no more than kg 500
Drifting diameter, mm 70
59
WELLHEAD EQUIPMENT
CROSSOVER FLANGES
Overview
Crossover flanges intended for connection of wellhead equipment having flanged connections to
equipment having a threaded connection.
Technical specifications
Name Nominal inside diameter Thread mark Flange mark
60
WELLHEAD EQUIPMENT
CROSSOVER COIL
Overview
The crossover coil is a connecting element in the wellhead arrangement of the oil well between the
flanges in accordance with GOST 28919.
Technical specifications
Name Drift diameter D, mm
KP-80×70-80×70 80
KP-180×21-180×70 180
KP-80×70-180×70 80
KP-80×70-180×21 80
KP-80×70-80×35 80
KP-80×70-60×70 60
KP-80×70-80×14 80
KP-80×70-100×35 80
KP-80×70-100×70 80
KP-80х70-230х35 80
KP-80×70-80×21 80
KP-80×70-65×35 65
KP-80×70-65×14 65
KP-80×70-65×70 65
KP-80х70-100х21 80
KP-80х70-100х100 80
KP-80×70-65×105 65
KP-80×70-100×14 80
It is possible to supply transition rails comes with studs and gaskets for flanges in accordance with
GOST28919-91.
61
WELLHEAD EQUIPMENT
Overview
The sealing coil (flange) is intended to seal a round pipe in the presence of pressure at the wellhead.
Allows the axial movement of the pipe, its rotation, dragging the sleeves from the bottom up and pushing
downwards under pressure. The values of the working pressures for pulling and pushing the sleeves
depend on the diameter of the pipes and sleeves.
Technical specifications
Diameter, The diameter of the Weight, Operating pressure Internal drift
Name
mm sealing tubes, mm kg of the body, MPa diameter, mm
62
WELLHEAD EQUIPMENT
Overview
Flanged coil (mid-mounted) is a transitional element in the layout of the wellhead of the oil well between
the flanges, made in accordance with GOST 28919-91 or API 6A and is used for hanging of tubing string.
Technical specifications
Connecting
D, Designation of the upper Designation of the lower
Name thread for tubing in
mm flange flange
accordance with GOST 633
63
WELLHEAD EQUIPMENT
Overview
The Cross connection flange (all flange cross) intended to connect the wellhead equipment having
flanges made in accordance with GOST 28919-91 or API 6A and strapping.
Technical specifications
Connecting flange Connecting thread of lateral tap
Name Drift diameter
GOST 28919-91 GOST 633-80
64
EQUIPMENT FOR WELLS’ COMPLETION BY UNCEMENTED LINERS
65
EQUIPMENT FOR WELLS’ COMPLETION BY UNCEMENTED LINERS
Overview
Circulating sub TSP-127 is run into the well as a component part of liner string and provides the possibility
of fluid pumping over through it in the open position while running into the hole. Circulating sub TSP-137
is mounted, as a rule, just above liner string shoe. The purpose of the following circulating sub TSP-137
application – hydraulic isolation of liner string below and above of the crossover sub stroked to “closed”
position.
Technical specifications
– Piston is supplied with locking that prevents the next opening in case of back pressure;
– Circulating sub TSP-137 is used into the wells for selective fracture treatments in openhole;
– Can be run into vertical, deviated and horizontal wells;
– Setting of pressure activation – closure is set on by the selection of certain quantity of shear pins prior
running into the hole.
66
EQUIPMENT FOR WELLS’ COMPLETION BY UNCEMENTED LINERS
Overview
Hydraulic sleeve MG-139,7 is a sealed device with a displaceable piston by which we can achieve
connections of tubing and casing annulus. It is run into the hole as a component part of liner string. Sleeve
activating is made by certain pressure making inside liner string. Upon the completion of fracturing without
any extra works at drilling out, the sleeve has the dimeter equal with other parts of liner string.
Technical specifications
– Hydraulic sleeve is applied for the wells for selective fracturing in openhole;
– Can be run into vertical, deviated and horizontal wells;
– It is mounted in the bottom part of assembly;
– Opening is made at differential pressure making inside and outside of hydraulic sleeve;
– Setting of pressure activation – opening is set on by the selection of certain quantity of shear pins
prior running into the hole.
67
EQUIPMENT FOR WELLS’ COMPLETION BY UNCEMENTED LINERS
PACKER PZG145
Overview
Packer PZG-145 is the device set in openhole and in closed hole allowing to perform pressure tight isolation
of zones behind and below packer, activated hydraulically owing to predetermined pressure differential
between packer internal and outside space. packer PZG-145 has straight drift diameter and is applied as a
rule for multistage fracturing in openhole.
Technical specifications
– packer of hydraulic setting for sublayers isolation at completion and selective treatment of formations;
– It can be used in openhole or in cased hole and in the assembly of cemented liners;
– The construction prevents early setting owing to setting of pressure activating immediately prior to
running into the hole;
– Сlickwork after activating keeps packer seal in compressed position regardless of course of pressure
change;
– Any quantity of packers can be run into the hole;
68
EQUIPMENT FOR WELLS’ COMPLETION BY UNCEMENTED LINERS
Overview
Stinger of model SYA-147/114/89 is intended for pressure-tight connection of tubing string with liner hanger at multi staged fracture
treatment performance (in liners Ø 114,3 mm). After set of equipment setting into the well for multi-staged fracturing performance
and setting device retrieving, stinger is run into the hole on tubing string. After stinger RIH at the predetermined depth there is a stinger
connection with packer PVP- 150.7/100-ОТТМ-114, that is represented by “liners’ head”. Stinger consists of gasket set, the size of which
is compatible with burnished packer funnel ID PVP- 150.7/100-ОТТМ-114. Burnished packer funnel top has a special section line for left
thread of stinger anchor unit. After stinger’s setting into a burnished packer funnel there is a necessity to perform 0,2…0,5t unloading,
thereat there is stinger anchoring in packer- liner hanger. Upon frac works’ completion stinger either is kept for the period of operational
activity or is retrieved from the well. Stinger’s disconnection from packer-hanger is performed just by turning to the right.
Technical specifications
Pressure differential taken up by stinger 70 MPa
Max extension load 400 kN
Installation weight min-max 0,2-0,5 t
Fixing mechanism Threaded basket grapple
Quantity of seals’ rows 2
Length 1010 mm
Max temperature of exploitation 150 °С
ID 98,3 / 81,5 mm
Coupling thread NKT 114 / NKT 89*
OD 149 mm
Retrieving 6-8 rotations clockwise (to the right)
69
EQUIPMENT FOR WELLS’ COMPLETION BY UNCEMENTED LINERS
Overview
Packer PVP-150.7/100-ОТТМ 114 is non-recoverable packer that has been specially designed for multi staged
fracturing. Packer-hanger has full-bore diameter. Packer RIH and setting is conducted by hydraulic setting device PU-
149,3/55-З 102/М78х3, that consists of hydraulic setting cylinders for packer activation as well as adapter with left
thread for mechanical disconnection from packer-hanger by rotating to the right after activating. Top packer hook is
equipped by burnished guiding funnel that is used for any downhole equipment running into liner string, as well as for
stinger SYA-147/114/89 locking up for multi staged fracturing.
Technical specifications
Operational pressure 70 MPa
Max extension load 765 kN
Application interval 154…162 mm
Length 1875 mm
Max exploitation temperature 150 °С
ID 100 mm
Connecting thread ОТТМ 114
OD 150,7 mm
70
EQUIPMENT FOR WELLS’ COMPLETION BY UNCEMENTED LINERS
Overview
Hydraulic setting device PU-149,3/55-З 102/М78х3 is used for RIH and activation of packer-hanger PVP- 150.7/100-ОТТМ-114
into the well as a part of standard system of multi staged fracturing. Setting device has a hydraulic principle of action. After running
into the hole to a selected depth there is pressure rise in tubing towards isolating device below the instrument where seat is for
ball pumping over from wellhead. Applied pressure cuts off the screws and hydraulic cylinders are moving to the fore activating
the rams and sealing packer’s element. After packer setting and pressure testing setting device is disconnecting by string pulling
and rotating to the right. The ports, located between O-rings of setting device, provide fluid flowing during retrieving from the well.
Technical specifications
Operational pressure 70 MPa
Max extension load 450 kN
Length 2410 mm
Max exploitation temperature 150 °С
ID 55 mm
Connecting thread (top /bottom) М 78 х 3
OD 150 mm
Max rotation torque 7…9 kN*м
Makeup torque of connecting thread Z-102 10..12 kN*м
Makeup torque of connecting thread М78х3 1…3 kN*м
71
EQUIPMENT FOR WELLS’ COMPLETION BY UNCEMENTED LINERS
Overview
Hydraulic port P-143/98-ОТТМ114 is a sealed device with displaceable piston due to which its possible to get
communication between tubing and annulus for multi staged fracturing performance. Hydraulic port is run into the hole
as a component part of liner string. Hydraulic port activation is made by dropping of the ball of a certain diameter. The
ball is dropping from wellhead to tubing string added up to liner’s head and gasketed by the stinger. Then the ball has
been pumped over to its setting into the seat then the pressure is making required for withheld screws cutting off, after
that hydraulic port is opening. Upon fracturing completion activating balls are washed out owing to CT unit or should be
drilled out jointly with the seats for fullbore diameter of liner string.
Technical specifications
Easily drilled over material of seats
Possibility of up to 20 ports’ installation into assembly
Operational pressure 700 atm
Operational temperature 150 °С
Connecting threads ОТТМ 114
Length 822 mm
OD 143 mm
Tensile load rating 765 kN
28.6 26.1
31.8 29.4
35 32.5
38.1 35.6
41.2 38.9
44.45 42
47.7 45.2
50.8 48.4
54 51.6
57.2 54.7
60.4 58
63.5 61
66.7 64.2
70 67.5
73 70.6
76.2 73.6
79.4 77
82.6 80.2
85.8 83.3
72
EQUIPMENT FOR WELLS’ COMPLETION BY UNCEMENTED LINERS
Overview
Drilled balls are applied for technological operations conducting at fracture treatment (fracturing), namely frac sleeves activating (ports’ opening). The balls are run into the
hole while cleaning by working fluid at fracture treatment. Pass through ports of downhole equipment should allow unobstructed ball movement up to the setting of the ball
into the appropriately sized seat of frac sleeve.
Technical specifications
Composite Aluminium
73
contact@packer-tools.ru
www.packer-tools.ru